LPT Driver Boot Messages, Issue #555

LPT driver will now display hardware that is not detected.  Thanks and credit to @robbbates.

Source/HBIOS/lpt.asm

@@ -95,10 +95,18 @@ LPT_INIT:
 	LD	IY,LPT_CFG		; POINT TO START OF CFG TABLE
 LPT_INIT0:
 	PUSH	BC			; SAVE LOOP CONTROL
+	CALL	LPT_PRTCFG		; PRINT CONFIG
 	CALL	LPT_INITUNIT		; HAND OFF TO UNIT INIT CODE
 	POP	BC			; RESTORE LOOP CONTROL
 ;
-	LD	A,(IY+1)		; GET THE LPT TYPE DETECTED
+	JR	Z,LPT_INIT1		; IF DETECTED, CONTINUE INIT
+	CALL	PC_SPACE		; FORMATTING
+	LD	DE,LPT_STR_NOLPT	; NO LPT MESSAGE
+	CALL	WRITESTR		; DISPLAY IT
+	JR	LPT_INIT2		; AND LOOP AS NEEDED
+;
+LPT_INIT1:
+	LD	A,(IY+1)		; GET THE LPT TYPE
 	OR	A			; SET FLAGS
 	JR	Z,LPT_INIT2		; SKIP IT IF NOTHING FOUND
 ;
@@ -107,7 +115,6 @@ LPT_INIT0:
 	POP	DE			; ... TO DE
 	LD	BC,LPT_FNTBL		; BC := FUNCTION TABLE ADDRESS
 	CALL	NZ,CIO_ADDENT		; ADD ENTRY IF LPT FOUND, BC:DE
-	CALL	LPT_PRTCFG		; PRINT IF NOT ZERO
 	POP	BC			; RESTORE LOOP CONTROL
 ;
 LPT_INIT2:
@@ -123,9 +130,7 @@ LPT_INIT3:
 ;
 LPT_INITUNIT:
 	CALL	LPT_DETECT		; DETERMINE LPT TYPE
-	LD	(IY+1),A		; SAVE IN CONFIG TABLE
-	OR	A			; SET FLAGS
-	RET	Z			; ABORT IF NOTHING THERE
+	RET	NZ			; ABORT IF NOTHING THERE
 ;
 	; UPDATE WORKING LPT DEVICE NUM
 	LD	HL,LPT_DEV		; POINT TO CURRENT DEVICE NUM
@@ -326,15 +331,7 @@ LPT_DETECT:
 ;
 LPT_DETECT:
 	LD	C,(IY+3)		; BASE PORT ADDRESS
-	CALL	LPT_DETECT2		; CHECK IT
-	JR	Z,LPT_DETECT1		; FOUND IT, RECORD IT
-	LD	A,LPTMODE_NONE		; NOTHING FOUND
-	RET				; DONE
-;
-LPT_DETECT1:
-	; LPT FOUND, RECORD IT
-	LD	A,LPTMODE_SPP		; RETURN CHIP TYPE
-	RET				; DONE
+	JR	LPT_DETECT2		; CHECK IT
 ;
 LPT_DETECT2:
 	; LOOK FOR LPT AT BASE PORT ADDRESS IN C
@@ -394,20 +391,13 @@ LPT_DETECT:
 	CALL	PRTHEXBYTE
   #ENDIF
 	CP	$A5			; CHECK FOR TEST VALUE
-	JR	Z,LPT_DETECT1		; FOUND IT
-	LD	A,LPTMODE_NONE		; NOT FOUND
-	RET
-;
-LPT_DETECT1:
-	; LPT FOUND, RECORD IT
-	LD	A,LPTMODE_MG014		; RETURN CHIP TYPE
-	RET				; DONE
+	RET				; ZF SET IF DETECTED
 #ENDIF
 ;
 #IF (LPTMODE == LPTMODE_S100)
 LPT_DETECT:
 	; PORT ALWAYS EXISTS ON FPGA
-	LD	A,LPTMODE_S100		; RETURN CHIP TYPE
+	XOR	A			; SIGNAL SUCCESS
 	RET				; DONE
 #ENDIF
 ;
@@ -417,7 +407,7 @@ LPT_PRTCFG:
 	; ANNOUNCE PORT
 	CALL	NEWLINE			; FORMATTING
 	PRTS("LPT$")			; FORMATTING
-	LD	A,(IY)			; DEVICE NUM
+	LD	A,(IY+2)		; DEVICE NUM
 	CALL	PRTDECB			; PRINT DEVICE NUM
 	PRTS(": IO=0x$")		; FORMATTING
 	LD	A,(IY+3)		; GET BASE PORT
@@ -452,11 +442,13 @@ LPT_TYPE_MAP:
 		.DW	LPT_STR_MG014
 		.DW	LPT_STR_S100
 ;
-LPT_STR_NONE	.DB	"<NOT PRESENT>$"
+LPT_STR_NONE	.DB	"???$"
 LPT_STR_SPP	.DB	"SPP$"
 LPT_STR_MG014	.DB	"MG014$"
 LPT_STR_S100	.DB	"S100$"
 ;
+LPT_STR_NOLPT	.DB	"NOT PRESENT$"
+;
 ; WORKING VARIABLES
 ;
 LPT_DEV		.DB	0		; DEVICE NUM USED DURING INIT
@@ -468,7 +460,7 @@ LPT_CFG:
 LPT0_CFG:
 	; LPT MODULE A CONFIG
 	.DB	0			; DEVICE NUMBER (SET DURING INIT)
-	.DB	0			; LPT TYPE (SET DURING INIT)
+	.DB	LPTMODE			; LPT MODE
 	.DB	0			; MODULE ID
 	.DB	LPT0BASE		; BASE PORT
 	.DW	0			; LINE CONFIGURATION
@@ -494,7 +486,7 @@ LPT_CFGSIZ	.EQU	$ - LPT_CFG	; SIZE OF ONE CFG TABLE ENTRY
 LPT1_CFG:
 	; LPT MODULE B CONFIG
 	.DB	0			; DEVICE NUMBER (SET DURING INIT)
-	.DB	0			; LPT TYPE (SET DURING INIT)
+	.DB	LPTMODE			; LPT MODE
 	.DB	1			; MODULE ID
 	.DB	LPT1BASE		; BASE PORT
 	.DW	0			; LINE CONFIGURATION