Multiple

- Complete initial support for Karl's Z280 module w/ 512K RAM/ROM module
- Allow swapping Z180 serial ports via ASCISWAP config variable
- Fix Z180 include file per Issue #141 from J.B. Lang

Binary/RomList.txt

@@ -182,6 +182,23 @@ RCZ180 (RCZ180_nat.rom & RCZ180_ext.rom):
    - RCZ180_ext.rom uses external bank management to access
      memory, such as the 512K RAM/ROM module.
 
+RCZ280 (RCZ280_ext.rom):
+ *** Experimental ***
+ - Assumes CPU oscillator of 24 MHz
+ - Bus clock will be 6 MHz, so does not match RC2014 standard!!!
+ - Requires 512K RAM/ROM module
+ - Auto detects Serial I/O Module (ACIA), Dual Serial
+   Module (SIO/2), and EP Dual UART.
+ - Console on whichever serial module is installed,
+   order of priority is UART, SIO, then ACIA.
+ - Baud rate is determined by hardware, but normally 115200.
+ - Auto support for RC2014 Compact Flash Module
+ - Auto support for RC2014 PPIDE Module
+ - Support for Scott Baker SIO board may be enabled in config
+ - Support for Scott Baker floppy controllers (SMC & WDC) may
+   be enabled in config
+ - Support for J.B. Lang TMS9918 video card may be enabled in config
+
 SCZ180 (SCZ180_126.rom, SCZ180_130.rom, SCZ180_131.rom):
  - Same as RCZ180
  - Adds auto support for SPI SD Card

Doc/ChangeLog.txt

@@ -5,6 +5,7 @@ Version 3.1.1
 - WBW: Change Propeller VGA signal timings to 60Hz refresh
 - WBW: Enhanced SYSTEM RESET function to allow a warm start back to boot loader
 - C?O: Add DUART driver
+- WBW: Early Z280 support (requires 512K RAM/ROM board)
 
 Version 3.1
 -----------

Source/HBIOS/Build.ps1

@@ -19,7 +19,7 @@ param([string]$Platform = "", [string]$Config = "", [string]$RomSize = "512", [s
 # setup mechanism so that multiple configuration are not needed.  When building for UNA, the pre-built
 # UNA BIOS is simply imbedded, it is not built here.
 #
-$PlatformListZ80 = "SBC", "ZETA", "ZETA2", "RCZ80", "EZZ80", "UNA"
+$PlatformListZ80 = "SBC", "ZETA", "ZETA2", "RCZ80", "RCZ280", "EZZ80", "UNA"
 $PlatformListZ180 = "N8", "MK4", "RCZ180", "SCZ180", "DYNO"
 
 #

Source/HBIOS/Config/RCZ280_ext.asm

@@ -0,0 +1,39 @@
+;
+;==================================================================================================
+;   RC2014 Z280 STANDARD CONFIGURATION (EXTERNAL 512K RAM/ROM BANKED MEMORY MODULE)
+;==================================================================================================
+;
+; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
+; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
+; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
+; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
+; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
+; YOUR FILE IN THE BUILD PROCESS.
+;
+; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
+; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
+; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
+; SETTINGS.
+;
+; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
+; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
+; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
+; DIRECTORIES ABOVE THIS ONE).
+;
+#define	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
+;
+#include "cfg_rcz280.asm"
+;
+CPUOSC		.SET	7372800		; CPU OSC FREQ IN MHZ
+;
+INTMODE		.SET	1
+;
+UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+ACIAENABLE	.SET	TRUE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
+SIOENABLE	.SET	TRUE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
+;
+IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
+;
+PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Makefile

@@ -11,6 +11,7 @@ else
 	OBJECTS += N8_std.rom N8_std.com
 	OBJECTS += RCZ180_ext.rom RCZ180_ext.com
 	OBJECTS += RCZ180_nat.rom RCZ180_nat.com
+	OBJECTS += RCZ280_ext.rom RCZ280_ext.com
 	OBJECTS += RCZ80_kio.rom RCZ80_kio.com
 	OBJECTS += RCZ80_mt.rom RCZ80_mt.com
 	OBJECTS += RCZ80_duart.rom RCZ80_duart.com

Source/HBIOS/asci.asm

@@ -796,8 +796,32 @@ ASCI1_BUFSZ	.EQU	$ - ASCI1_BUF	; SIZE OF RING BUFFER
 ;
 ASCI_CFG:
 ;
+#IF (ASCISWAP)
+;
+ASCI1_CFG:
+	; ASCI CHANNEL B CONFIG
+	.DB	0			; DEVICE NUMBER (SET DURING INIT)
+	.DB	0			; ASCI TYPE (SET DURING INIT)
+	.DB	1			; MODULE ID
+	.DB	ASCI1_BASE		; BASE PORT
+	.DW	ASCI1CFG		; LINE CONFIGURATION
+	.DW	ASCI1_RCVBUF		; POINTER TO RCV BUFFER STRUCT
+;
+ASCI_CFGSIZ	.EQU	$ - ASCI_CFG	; SIZE OF ONE CFG TABLE ENTRY
+;
+ASCI0_CFG:
+	; ASCI CHANNEL A CONFIG
+	.DB	0			; DEVICE NUMBER (SET DURING INIT)
+	.DB	0			; ASCI TYPE (SET DURING INIT)
+	.DB	0			; MODULE ID
+	.DB	ASCI0_BASE		; BASE PORT
+	.DW	ASCI0CFG		; LINE CONFIGURATION
+	.DW	ASCI0_RCVBUF		; POINTER TO RCV BUFFER STRUCT
+;
+#ELSE
+;
 ASCI0_CFG:
-	; ASCI MODULE A CONFIG
+	; ASCI CHANNEL A CONFIG
 	.DB	0			; DEVICE NUMBER (SET DURING INIT)
 	.DB	0			; ASCI TYPE (SET DURING INIT)
 	.DB	0			; MODULE ID
@@ -808,7 +832,7 @@ ASCI0_CFG:
 ASCI_CFGSIZ	.EQU	$ - ASCI_CFG	; SIZE OF ONE CFG TABLE ENTRY
 ;
 ASCI1_CFG:
-	; ASCI MODULE B CONFIG
+	; ASCI CHANNEL B CONFIG
 	.DB	0			; DEVICE NUMBER (SET DURING INIT)
 	.DB	0			; ASCI TYPE (SET DURING INIT)
 	.DB	1			; MODULE ID
@@ -816,4 +840,7 @@ ASCI1_CFG:
 	.DW	ASCI1CFG		; LINE CONFIGURATION
 	.DW	ASCI1_RCVBUF		; POINTER TO RCV BUFFER STRUCT
 ;
+#ENDIF
+;
+;
 ASCI_CFGCNT	.EQU	($ - ASCI_CFG) / ASCI_CFGSIZ

Source/HBIOS/cfg_dyno.asm

@@ -14,7 +14,7 @@
 #DEFINE PLATFORM_NAME "DYNO"
 ;
 PLATFORM	.EQU	PLT_DYNO	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO]
-CPUFAM		.EQU	CPU_Z180	; CPU FAMILY: CPU_[Z80|Z180]
+CPUFAM		.EQU	CPU_Z180	; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
 HBIOS_MUTEX	.EQU	FALSE		; ENABLE REENTRANT CALLS TO HBIOS (ADDS OVERHEAD)
@@ -79,6 +79,7 @@ DUARTENABLE	.EQU	FALSE		; DUART: ENABLE 2681/2692 SERIAL DRIVER (DUART.ASM)
 UARTENABLE	.EQU	FALSE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
+ASCISWAP	.EQU	FALSE		; ASCI: SWAP CHANNELS
 ASCI0CFG	.EQU	DEFSERCFG	; ASCI 0: SERIAL LINE CONFIG
 ASCI1CFG	.EQU	DEFSERCFG	; ASCI 1: SERIAL LINE CONFIG
 ;

Source/HBIOS/cfg_ezz80.asm

@@ -14,7 +14,7 @@
 #DEFINE PLATFORM_NAME "EASYZ80"
 ;
 PLATFORM	.EQU	PLT_EZZ80	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO]
-CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180]
+CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
 HBIOS_MUTEX	.EQU	FALSE		; ENABLE REENTRANT CALLS TO HBIOS (ADDS OVERHEAD)

Source/HBIOS/cfg_master.asm

@@ -11,7 +11,7 @@
 #DEFINE PLATFORM_NAME "ROMWBW"
 ;
 PLATFORM	.EQU	PLT_SBC		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO]
-CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180]
+CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
 HBIOS_MUTEX	.EQU	FALSE		; ENABLE REENTRANT CALLS TO HBIOS (ADDS OVERHEAD)
@@ -40,6 +40,9 @@ Z180_CLKDIV	.EQU	1		; Z180: CHK DIV: 0=OSC/2, 1=OSC, 2=OSC*2
 Z180_MEMWAIT	.EQU	0		; Z180: MEMORY WAIT STATES (0-3)
 Z180_IOWAIT	.EQU	1		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
 ;
+Z280_MEMWAIT	.EQU	0		; Z280: MEMORY WAIT STATES (0-3)
+Z280_IOWAIT	.EQU	1		; Z280: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
+;
 N8_PPI0		.EQU	$80		; N8: FIRST PARALLEL PORT REGISTERS BASE ADR
 N8_PPI1		.EQU	$84		; N8: SECOND PARALLEL PORT REGISTERS BASE ADR
 N8_RTC		.EQU	$88		; N8: RTC LATCH REGISTER ADR
@@ -119,6 +122,7 @@ UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
+ASCISWAP	.EQU	FALSE		; ASCI: SWAP CHANNELS
 ASCI0CFG	.EQU	DEFSERCFG	; ASCI 0: SERIAL LINE CONFIG
 ASCI1CFG	.EQU	DEFSERCFG	; ASCI 1: SERIAL LINE CONFIG
 ;

Source/HBIOS/cfg_mk4.asm

@@ -14,7 +14,7 @@
 #DEFINE PLATFORM_NAME "MARK IV"
 ;
 PLATFORM	.EQU	PLT_MK4		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO]
-CPUFAM		.EQU	CPU_Z180	; CPU FAMILY: CPU_[Z80|Z180]
+CPUFAM		.EQU	CPU_Z180	; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
 HBIOS_MUTEX	.EQU	FALSE		; ENABLE REENTRANT CALLS TO HBIOS (ADDS OVERHEAD)
@@ -94,6 +94,7 @@ UART4		.EQU	TRUE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
+ASCISWAP	.EQU	FALSE		; ASCI: SWAP CHANNELS
 ASCI0CFG	.EQU	DEFSERCFG	; ASCI 0: SERIAL LINE CONFIG
 ASCI1CFG	.EQU	DEFSERCFG	; ASCI 1: SERIAL LINE CONFIG
 ;

Source/HBIOS/cfg_n8.asm

@@ -14,7 +14,7 @@
 #DEFINE PLATFORM_NAME "N8"
 ;
 PLATFORM	.EQU	PLT_N8		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO]
-CPUFAM		.EQU	CPU_Z180	; CPU FAMILY: CPU_[Z80|Z180]
+CPUFAM		.EQU	CPU_Z180	; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
 HBIOS_MUTEX	.EQU	FALSE		; ENABLE REENTRANT CALLS TO HBIOS (ADDS OVERHEAD)
@@ -97,6 +97,7 @@ UART4		.EQU	TRUE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
+ASCISWAP	.EQU	FALSE		; ASCI: SWAP CHANNELS
 ASCI0CFG	.EQU	DEFSERCFG	; ASCI 0: SERIAL LINE CONFIG
 ASCI1CFG	.EQU	DEFSERCFG	; ASCI 1: SERIAL LINE CONFIG
 ;

Source/HBIOS/cfg_rcz180.asm

@@ -14,7 +14,7 @@
 #DEFINE PLATFORM_NAME "RC2014"
 ;
 PLATFORM	.EQU	PLT_RCZ180	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO]
-CPUFAM		.EQU	CPU_Z180	; CPU FAMILY: CPU_[Z80|Z180]
+CPUFAM		.EQU	CPU_Z180	; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
 HBIOS_MUTEX	.EQU	FALSE		; ENABLE REENTRANT CALLS TO HBIOS (ADDS OVERHEAD)
@@ -96,6 +96,7 @@ UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
+ASCISWAP	.EQU	FALSE		; ASCI: SWAP CHANNELS
 ASCI0CFG	.EQU	DEFSERCFG	; ASCI 0: SERIAL LINE CONFIG
 ASCI1CFG	.EQU	DEFSERCFG	; ASCI 1: SERIAL LINE CONFIG
 ;

Source/HBIOS/cfg_rcz280.asm

@@ -0,0 +1,217 @@
+;
+;==================================================================================================
+;   ROMWBW 2.X CONFIGURATION DEFAULTS FOR RC2014 Z280 (512K RAM/ROM CARD)
+;==================================================================================================
+;
+; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE. THIS FILE SHOULD *NOT* NORMALLY BE CHANGED.	INSTEAD, YOU SHOULD
+; OVERRIDE ANY SETTINGS YOU WANT USING A CONFIGURATION FILE IN THE CONFIG DIRECTORY
+; UNDER THIS DIRECTORY.
+;
+; THIS FILE CAN BE CONSIDERED A REFERENCE THAT LISTS ALL POSSIBLE CONFIGURATION SETTINGS
+; FOR THE PLATFORM.
+;
+#DEFINE PLATFORM_NAME "RC2014"
+;
+PLATFORM	.EQU	PLT_RCZ80	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO]
+CPUFAM		.EQU	CPU_Z280	; CPU FAMILY: CPU_[Z80|Z180|Z280]
+BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
+BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
+HBIOS_MUTEX	.EQU	FALSE		; ENABLE REENTRANT CALLS TO HBIOS (ADDS OVERHEAD)
+USELZSA2	.EQU	TRUE		; ENABLE FONT COMPRESSION
+TICKFREQ	.EQU	50		; DESIRED PERIODIC TIMER INTERRUPT FREQUENCY (HZ)
+;
+BOOT_TIMEOUT	.EQU	-1		; AUTO BOOT TIMEOUT IN SECONDS, -1 TO DISABLE, 0 FOR IMMEDIATE
+;
+CPUOSC		.EQU	24000000	; CPU OSC FREQ IN MHZ
+INTMODE		.EQU	0		; INTERRUPTS: 0=NONE, 1=MODE 1, 2=MODE 2
+DEFSERCFG	.EQU	SER_115200_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
+;
+RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
+MEMMGR		.EQU	MM_Z2		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180]
+MPGSEL_0	.EQU	$78		; Z2 MEM MGR BANK 0 PAGE SELECT REG (WRITE ONLY)
+MPGSEL_1	.EQU	$79		; Z2 MEM MGR BANK 1 PAGE SELECT REG (WRITE ONLY)
+MPGSEL_2	.EQU	$7A		; Z2 MEM MGR BANK 2 PAGE SELECT REG (WRITE ONLY)
+MPGSEL_3	.EQU	$7B		; Z2 MEM MGR BANK 3 PAGE SELECT REG (WRITE ONLY)
+MPGENA		.EQU	$7C		; Z2 MEM MGR PAGING ENABLE REGISTER (BIT 0, WRITE ONLY)
+;
+Z280_MEMWAIT	.EQU	0		; Z280: MEMORY WAIT STATES (0-3)
+Z280_IOWAIT	.EQU	1		; Z280: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
+;
+RTCIO		.EQU	$C0		; RTC LATCH REGISTER ADR
+;
+KIOENABLE	.EQU	FALSE		; ENABLE ZILOG KIO SUPPORT
+KIOBASE		.EQU	$80		; KIO BASE I/O ADDRESS
+;
+CTCENABLE	.EQU	FALSE		; ENABLE ZILOG CTC SUPPORT
+CTCDEBUG	.EQU	FALSE		; ENABLE CTC DRIVER DEBUG OUTPUT
+CTCBASE		.EQU	$88		; CTC BASE I/O ADDRESS
+CTCTIMER	.EQU	FALSE		; ENABLE CTC PERIODIC TIMER
+CTCMODE		.EQU	CTCMODE_TIM16	; CTC MODE: CTCMODE_[NONE|CTR|TIM16|TIM256]
+CTCPRE		.EQU	256		; PRESCALE CONSTANT (1-256)
+CTCPRECH	.EQU	2		; PRESCALE CHANNEL (0-3)
+CTCTIMCH	.EQU	3		; TIMER CHANNEL (0-3)
+CTCOSC		.EQU	7372800		; CTC CLOCK FREQUENCY
+;
+DIAGENABLE	.EQU	TRUE		; ENABLES OUTPUT TO 8 BIT LED DIAGNOSTIC PORT
+DIAGPORT	.EQU	$00		; DIAGNOSTIC PORT ADDRESS
+DIAGDISKIO	.EQU	TRUE		; ENABLES DISK I/O ACTIVITY ON DIAGNOSTIC LEDS
+;
+LEDENABLE	.EQU	FALSE		; ENABLES STATUS LED (SINGLE LED)
+LEDPORT		.EQU	$0E		; STATUS LED PORT ADDRESS
+LEDDISKIO	.EQU	TRUE		; ENABLES DISK I/O ACTIVITY ON STATUS LED
+;
+DSKYENABLE	.EQU	FALSE		; ENABLES DSKY (DO NOT COMBINE WITH PPIDE)
+;
+CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
+VDAEMU		.EQU	EMUTYP_ANSI	; VDA EMULATION: EMUTYP_[TTY|ANSI]
+ANSITRACE	.EQU	1		; ANSI DRIVER TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+;
+DSRTCENABLE	.EQU	TRUE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
+DSRTCMODE	.EQU	DSRTCMODE_STD	; DSRTC: OPERATING MODE: DSRTC_[STD|MFPIC]
+DSRTCCHG	.EQU	FALSE		; DSRTC: FORCE BATTERY CHARGE ON (USE WITH CAUTION!!!)
+;
+BQRTCENABLE	.EQU	FALSE		; BQRTC: ENABLE BQ4845 CLOCK DRIVER (BQRTC.ASM)
+BQRTC_BASE	.EQU	$50		; BQRTC: I/O BASE ADDRESS
+;
+INTRTCENABLE	.EQU	FALSE		; ENABLE PERIODIC INTERRUPT CLOCK DRIVER (INTRTC.ASM)
+;
+HTIMENABLE	.EQU	FALSE		; ENABLE SIMH TIMER SUPPORT
+SIMRTCENABLE	.EQU	FALSE		; ENABLE SIMH CLOCK DRIVER (SIMRTC.ASM)
+;
+DUARTENABLE	.EQU	FALSE		; DUART: ENABLE 2681/2692 SERIAL DRIVER (DUART.ASM)
+DUARTCNT	.EQU	2		; DUART: NUMBER OF CHIPS TO DETECT (1-2)
+DUART0BASE	.EQU	$A0		; DUART 0: BASE ADDRESS OF CHIP
+DUART0ACFG	.EQU	DEFSERCFG	; DUART 0A: SERIAL LINE CONFIG
+DUART0BCFG	.EQU	DEFSERCFG	; DUART 0B: SERIAL LINE CONFIG
+DUART1BASE	.EQU	$40		; DUART 1: BASE ADDRESS OF CHIP
+DUART1ACFG	.EQU	DEFSERCFG	; DUART 1A: SERIAL LINE CONFIG
+DUART1BCFG	.EQU	DEFSERCFG	; DUART 1B: SERIAL LINE CONFIG
+;
+UARTENABLE	.EQU	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
+UARTCFG		.EQU	DEFSERCFG | SER_RTS	; UART: LINE CONFIG FOR UART PORTS
+UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
+UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
+UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
+UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
+;
+ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
+;
+ACIAENABLE	.EQU	TRUE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
+ACIADEBUG	.EQU	FALSE		; ACIA: ENABLE DEBUG OUTPUT
+ACIACNT		.EQU	1		; ACIA: NUMBER OF CHIPS TO DETECT (1-2)
+ACIA0BASE	.EQU	$80		; ACIA 0: REGISTERS BASE ADR
+ACIA0CLK	.EQU	7372800		; ACIA 0: OSC FREQ IN HZ
+ACIA0DIV	.EQU	1		; ACIA 0: SERIAL CLOCK DIVIDER
+ACIA0CFG	.EQU	DEFSERCFG	; ACIA 0: SERIAL LINE CONFIG  (SEE STD.ASM)
+ACIA1BASE	.EQU	$40		; ACIA 1: REGISTERS BASE ADR
+ACIA1CLK	.EQU	7372800		; ACIA 1: OSC FREQ IN HZ
+ACIA1DIV	.EQU	1		; ACIA 1: SERIAL CLOCK DIVIDER
+ACIA1CFG	.EQU	DEFSERCFG	; ACIA 1: SERIAL LINE CONFIG  (SEE STD.ASM)
+;
+SIOENABLE	.EQU	TRUE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
+SIODEBUG	.EQU	FALSE		; SIO: ENABLE DEBUG OUTPUT
+SIOCNT		.EQU	2		; SIO: NUMBER OF CHIPS TO DETECT (1-2), 2 CHANNELS PER CHIP
+SIO0MODE	.EQU	SIOMODE_RC	; SIO 0: CHIP TYPE: SIOMODE_[STD|RC|SMB|ZP]
+SIO0BASE	.EQU	$80		; SIO 0: REGISTERS BASE ADR
+SIO0ACLK	.EQU	7372800		; SIO 0A: OSC FREQ IN HZ, ZP=2457600/4915200, RC/SMB=7372800
+SIO0ACFG	.EQU	DEFSERCFG	; SIO 0A: SERIAL LINE CONFIG
+SIO0ACTCC	.EQU	-1		; SIO 0A: CTC CHANNEL 0=A, 1=B, 2=C, 3=D, -1 FOR NONE
+SIO0BCLK	.EQU	7372800		; SIO 0B: OSC FREQ IN HZ, ZP=2457600/4915200, RC/SMB=7372800
+SIO0BCFG	.EQU	DEFSERCFG	; SIO 0B: SERIAL LINE CONFIG
+SIO0BCTCC	.EQU	-1		; SIO 0B: CTC CHANNEL 0=A, 1=B, 2=C, 3=D, -1 FOR NONE
+SIO1MODE	.EQU	SIOMODE_RC	; SIO 1: CHIP TYPE: SIOMODE_[STD|RC|SMB|ZP]
+SIO1BASE	.EQU	$84		; SIO 1: REGISTERS BASE ADR
+SIO1ACLK	.EQU	7372800		; SIO 1A: OSC FREQ IN HZ, ZP=2457600/4915200, RC/SMB=7372800
+SIO1ACFG	.EQU	DEFSERCFG	; SIO 1A: SERIAL LINE CONFIG
+SIO1ACTCC	.EQU	-1		; SIO 1A: CTC CHANNEL 0=A, 1=B, 2=C, 3=D, -1 FOR NONE
+SIO1BCLK	.EQU	7372800		; SIO 1B: OSC FREQ IN HZ, ZP=2457600/4915200, RC/SMB=7372800
+SIO1BCFG	.EQU	DEFSERCFG	; SIO 1B: SERIAL LINE CONFIG
+SIO1BCTCC	.EQU	-1		; SIO 1B: CTC CHANNEL 0=A, 1=B, 2=C, 3=D, -1 FOR NONE
+;
+XIOCFG		.EQU	DEFSERCFG	; XIO: SERIAL LINE CONFIG
+;
+VDUENABLE	.EQU	FALSE		; VDU: ENABLE VDU VIDEO/KBD DRIVER (VDU.ASM)
+CVDUENABLE	.EQU	FALSE		; CVDU: ENABLE CVDU VIDEO/KBD DRIVER (CVDU.ASM)
+NECENABLE	.EQU	FALSE		; NEC: ENABLE NEC UPD7220 VIDEO/KBD DRIVER (NEC.ASM)
+TMSENABLE	.EQU	FALSE		; TMS: ENABLE TMS9918 VIDEO/KBD DRIVER (TMS.ASM)
+TMSMODE		.EQU	TMSMODE_RC	; TMS: DRIVER MODE: TMSMODE_[SCG/N8]
+TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
+VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
+;
+MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
+MDTRACE		.EQU	1		; MD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+;
+FDENABLE	.EQU	FALSE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
+FDMODE		.EQU	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDCNT		.EQU	2		; FD: NUMBER OF FLOPPY DRIVES ON THE INTERFACE (1-2)
+FDTRACE		.EQU	1		; FD: TRACE LEVEL (0=NO,1=FATAL,2=ERRORS,3=ALL)
+FDMEDIA		.EQU	FDM144		; FD: DEFAULT MEDIA FORMAT FDM[720|144|360|120|111]
+FDMEDIAALT	.EQU	FDM720		; FD: ALTERNATE MEDIA FORMAT FDM[720|144|360|120|111]
+FDMAUTO		.EQU	TRUE		; FD: AUTO SELECT DEFAULT/ALTERNATE MEDIA FORMATS
+;
+RFENABLE	.EQU	FALSE		; RF: ENABLE RAM FLOPPY DRIVER
+;
+IDEENABLE	.EQU	FALSE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
+IDETRACE	.EQU	1		; IDE: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+IDECNT		.EQU	1		; IDE: NUMBER OF IDE INTERFACES TO DETECT (1-3), 2 DRIVES EACH
+IDE0MODE	.EQU	IDEMODE_RC	; IDE 0: DRIVER MODE: IDEMODE_[DIO|DIDE|MK4|RC]
+IDE0BASE	.EQU	$10		; IDE 0: IO BASE ADDRESS
+IDE0DATLO	.EQU	$00		; IDE 0: DATA LO PORT FOR 16-BIT I/O
+IDE0DATHI	.EQU	$00		; IDE 0: DATA HI PORT FOR 16-BIT I/O
+IDE0A8BIT	.EQU	TRUE		; IDE 0A (MASTER): 8 BIT XFER
+IDE0B8BIT	.EQU	TRUE		; IDE 0B (MASTER): 8 BIT XFER
+IDE1MODE	.EQU	IDEMODE_NONE	; IDE 1: DRIVER MODE: IDEMODE_[DIO|DIDE|MK4|RC]
+IDE1BASE	.EQU	$00		; IDE 1: IO BASE ADDRESS
+IDE1DATLO	.EQU	$00		; IDE 1: DATA LO PORT FOR 16-BIT I/O
+IDE1DATHI	.EQU	$00		; IDE 1: DATA HI PORT FOR 16-BIT I/O
+IDE1A8BIT	.EQU	TRUE		; IDE 1A (MASTER): 8 BIT XFER
+IDE1B8BIT	.EQU	TRUE		; IDE 1B (MASTER): 8 BIT XFER
+IDE2MODE	.EQU	IDEMODE_NONE	; IDE 2: DRIVER MODE: IDEMODE_[DIO|DIDE|MK4|RC]
+IDE2BASE	.EQU	$00		; IDE 2: IO BASE ADDRESS
+IDE2DATLO	.EQU	$00		; IDE 2: DATA LO PORT FOR 16-BIT I/O
+IDE2DATHI	.EQU	$00		; IDE 2: DATA HI PORT FOR 16-BIT I/O
+IDE2A8BIT	.EQU	TRUE		; IDE 2A (MASTER): 8 BIT XFER
+IDE2B8BIT	.EQU	TRUE		; IDE 2B (MASTER): 8 BIT XFER
+;
+PPIDEENABLE	.EQU	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
+PPIDETRACE	.EQU	1		; PPIDE: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+PPIDECNT	.EQU	1		; PPIDE: NUMBER OF PPI CHIPS TO DETECT (1-3), 2 DRIVES PER CHIP
+PPIDE0BASE	.EQU	$20		; PPIDE 0: PPI REGISTERS BASE ADR
+PPIDE0A8BIT	.EQU	FALSE		; PPIDE 0A (MASTER): 8 BIT XFER
+PPIDE0B8BIT	.EQU	FALSE		; PPIDE 0B (SLAVE): 8 BIT XFER
+PPIDE1BASE	.EQU	$00		; PPIDE 1: PPI REGISTERS BASE ADR
+PPIDE1A8BIT	.EQU	FALSE		; PPIDE 1A (MASTER): 8 BIT XFER
+PPIDE1B8BIT	.EQU	FALSE		; PPIDE 0B (SLAVE): 8 BIT XFER
+PPIDE2BASE	.EQU	$00		; PPIDE 2: PPI REGISTERS BASE ADR
+PPIDE2A8BIT	.EQU	FALSE		; PPIDE 2A (MASTER): 8 BIT XFER
+PPIDE2B8BIT	.EQU	FALSE		; PPIDE 0B (SLAVE): 8 BIT XFER
+;
+SDENABLE	.EQU	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
+SDMODE		.EQU	SDMODE_MT	; SD: DRIVER MODE: SDMODE_[JUHA|N8|CSIO|PPI|UART|DSD|MK4|SC|MT]
+SDCNT		.EQU	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD & SC ONLY
+SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+SDCSIOFAST	.EQU	FALSE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
+;
+PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
+;
+PPPENABLE	.EQU	FALSE		; PPP: ENABLE ZETA PARALLEL PORT PROPELLER BOARD DRIVER (PPP.ASM)
+;
+HDSKENABLE	.EQU	FALSE		; HDSK: ENABLE SIMH HDSK DISK DRIVER (HDSK.ASM)
+;
+PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
+PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)
+PPI_SBC		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR 8255 CHIP
+;
+UFENABLE	.EQU	FALSE		; UF: ENABLE ECB USB FIFO DRIVER (UF.ASM)
+;
+AUDIOTRACE	.EQU	FALSE		; ENABLE TRACING TO CONSOLE OF SOUND DRIVER
+SN76489ENABLE	.EQU	FALSE		; SN76489 SOUND DRIVER
+SN7CLK		.EQU	7372800 / 4	; DEFAULT TO CPUOSC / 4
+
+AY38910ENABLE	.EQU	FALSE		; AY: AY-3-8910 / YM2149 SOUND DRIVER
+AY_CLK		.EQU	7372800 / 4	; DEFAULT TO CPUOSC / 4
+AYMODE		.EQU	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG/N8/RCZ80/RCZ180]
+SPKENABLE	.EQU	FALSE		; SPK: ENABLE RTC LATCH IOBIT SOUND DRIVER (SPK.ASM)

Source/HBIOS/cfg_rcz80.asm

@@ -14,7 +14,7 @@
 #DEFINE PLATFORM_NAME "RC2014"
 ;
 PLATFORM	.EQU	PLT_RCZ80	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO]
-CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180]
+CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
 HBIOS_MUTEX	.EQU	FALSE		; ENABLE REENTRANT CALLS TO HBIOS (ADDS OVERHEAD)

Source/HBIOS/cfg_sbc.asm

@@ -14,7 +14,7 @@
 #DEFINE PLATFORM_NAME "SBC"
 ;
 PLATFORM	.EQU	PLT_SBC		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO]
-CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180]
+CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
 HBIOS_MUTEX	.EQU	FALSE		; ENABLE REENTRANT CALLS TO HBIOS (ADDS OVERHEAD)

Source/HBIOS/cfg_scz180.asm

@@ -14,7 +14,7 @@
 #DEFINE PLATFORM_NAME "SCZ180"
 ;
 PLATFORM	.EQU	PLT_SCZ180	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO]
-CPUFAM		.EQU	CPU_Z180	; CPU FAMILY: CPU_[Z80|Z180]
+CPUFAM		.EQU	CPU_Z180	; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
 HBIOS_MUTEX	.EQU	FALSE		; ENABLE REENTRANT CALLS TO HBIOS (ADDS OVERHEAD)
@@ -91,6 +91,7 @@ UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
+ASCISWAP	.EQU	FALSE		; ASCI: SWAP CHANNELS
 ASCI0CFG	.EQU	DEFSERCFG	; ASCI 0: SERIAL LINE CONFIG
 ASCI1CFG	.EQU	DEFSERCFG	; ASCI 1: SERIAL LINE CONFIG
 ;

Source/HBIOS/cfg_zeta.asm

@@ -14,7 +14,7 @@
 #DEFINE PLATFORM_NAME "ZETA"
 ;
 PLATFORM	.EQU	PLT_ZETA	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO]
-CPUFAM		.EQU	CPU_Z80		; CPU_[Z80|Z180]: CPU FAMILY
+CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; BIOS_[WBW|UNA]: HARDWARE BIOS
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
 HBIOS_MUTEX	.EQU	FALSE		; ENABLE REENTRANT CALLS TO HBIOS (ADDS OVERHEAD)

Source/HBIOS/cfg_zeta2.asm

@@ -14,7 +14,7 @@
 #DEFINE PLATFORM_NAME "ZETA V2"
 ;
 PLATFORM	.EQU	PLT_ZETA2	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO]
-CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180]
+CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
 HBIOS_MUTEX	.EQU	FALSE		; ENABLE REENTRANT CALLS TO HBIOS (ADDS OVERHEAD)

Source/HBIOS/hbios.asm

@@ -428,9 +428,9 @@ HBX_BNKSEL1:
 ;
 HBX_BNKCPY:
 #IF (INTMODE > 0)
-	LD	A,I
+	;LD	A,I
 	DI
-	PUSH	AF
+	;PUSH	AF
 #ENDIF
 	LD	(HBX_BC_SP),SP		; PUT STACK
 	LD	SP,HBX_TMPSTK		; ... IN HI MEM
@@ -462,8 +462,8 @@ HBX_BC_LAST:
 	LD	SP,$FFFF		; RESTORE STACK
 HBX_BC_SP	.EQU	$ - 2		; ... TO ORIGINAL VALUE
 #IF (INTMODE > 0)
-	POP	AF
-	JP	PO,$+4
+	;POP	AF
+	;JP	PO,$+4
 	EI
 #ENDIF
 	RET
@@ -824,19 +824,29 @@ HB_START:
 ;
 	LD	SP,HBX_LOC		; SETUP INITIAL STACK JUST BELOW HBIOS PROXY
 ;
-;#IF (CPUFAM == CPU_Z280)
-;	LD	C,$12		; CACHE CONTROL REGISTER
-;	LD	HL,$0060	; DISABLE INSTRUCTION CACHE
-;	;LDCTL	(C),HL		; SET IT (8 BITS)
-;	.DB	$ED,$6E
-;	;PCACHE			; PURGE ANY REMNANTS OF CACHE
-;	.DB	$ED,$65
-;#ENDIF
+#IF (CPUFAM == CPU_Z280)
+	;LD	C,$12		; CACHE CONTROL REGISTER
+	;LD	HL,$0060	; DISABLE INSTRUCTION CACHE
+	;;LDCTL	(C),HL		; SET IT (8 BITS)
+	;.DB	$ED,$6E
+	;;PCACHE			; PURGE ANY REMNANTS OF CACHE
+	;.DB	$ED,$65
+;
+	LD	C,$02		; BUS TIMING AND CONTROL REGISTER
+	LD	HL,$0033	; 3 I/O WAIT STATES ADDED
+	;LD	HL,$00F3	; 3 I/O W/S & 3 INT ACK W/S
+	;LDCTL	(C),HL		; SET IT (8 BITS)
+	.DB	$ED,$6E
+#ENDIF
 ;
 #IF (CPUFAM == CPU_Z180)
 	; SET BASE FOR CPU IO REGISTERS
+	; DO NOT USE Z180_ICR FROM Z180.INC BECAUSE THE ICR
+	; IS NOT YET AT THE RUNNING LOCATION.  AT RESET, THE Z180
+	; REGISTER BASE I/O ADDRESS IS ZERO, SO INITIALLY, ICR IS
+	; AT $3F.
 	LD	A,Z180_BASE
-	OUT0	(Z180_ICR),A
+	OUT0	($3F),A		; AT RESET, ICR IS AT $3F
 
 	DIAG(%00000010)
 
@@ -1090,12 +1100,13 @@ SAVE_REC_M:
 ;
 ; DISCOVER CPU TYPE
 ;
-; THIS CODE IS DERIVED FROM UNA BY JOHN COFFMAN
+; SOME OF THIS CODE IS DERIVED FROM UNA BY JOHN COFFMAN
 ;
 ;	0: Z80
 ;	1: Z80180 - ORIGINAL Z180 (EQUIVALENT TO HD64180)
 ;	2: Z8S180 - ORIGINAL S-CLASS, REV. K, AKA SL1960, NO ASCI BRG
 ;	3: Z8S180 - REVISED S-CLASS, REV. N, W/ ASCI BRG
+;	4: Z8280
 ;
 	LD	HL,0		; L = 0 MEANS Z80
 ;
@@ -1126,6 +1137,18 @@ SAVE_REC_M:
 ;
 #ENDIF
 ;
+#IF (CPUFAM == CPU_Z280)
+;
+	; TEST FOR Z280 PER ZILOG DOC
+	LD	A,$40		; INITIALIZE THE OPERAND
+	.DB	$CB,$37		; THIS INSTRUCTION WILL SET THE S FLAG
+				; ON THE Z80 CPU AND CLEAR THE S FLAG
+				; ON THE Z280 MPU.
+	JP	M,HB_CPU1	; IF Z80, SKIP AHEAD
+	LD	L,4		; WE ARE Z280
+;
+#ENDIF
+;
 HB_CPU1:
 	LD	A,L
 	LD	(HB_CPUTYPE),A
@@ -1174,6 +1197,16 @@ HB_CPU2:
 	LD	(CB_CPUKHZ),DE
 ;
 #ENDIF
+;
+#IF (CPUFAM == CPU_Z280)
+;
+	; Z280 PHI IS OSC / 2
+	LD	A,(CPUOSC / 2) / 1000000
+	LD	(CB_CPUMHZ),A
+	LD	DE,(CPUOSC / 2) / 1000
+	LD	(CB_CPUKHZ),DE
+;
+#ENDIF
 ;
 	DIAG(%00011111)
 ;
@@ -1267,7 +1300,6 @@ HB_CPU2:
 ;
 #ENDIF
 ;
-;
 ; INITIALIZE HEAP STORAGE
 ;
 	; INITIALIZE POINTERS
@@ -1454,18 +1486,22 @@ HB_SPDTST:
 ; DISPLAY CPU CONFIG
 ;
 	CALL	NEWLINE
+	XOR	A
 #IF (CPUFAM == CPU_Z180)
 	LD	A,Z180_MEMWAIT
-#ELSE
-	LD	A,0
+#ENDIF
+#IF (CPUFAM == CPU_Z280)
+	LD	A,Z280_MEMWAIT
 #ENDIF
 	CALL	PRTDECB
 	CALL	PRTSTRD
 	.TEXT	" MEM W/S, $"
+	LD	A,1
 #IF (CPUFAM == CPU_Z180)
 	LD	A,Z180_IOWAIT + 1
-#ELSE
-	LD	A,1
+#ENDIF
+#IF (CPUFAM == CPU_Z280)
+	LD	A,Z280_IOWAIT + 1
 #ENDIF
 	CALL	PRTDECB
 	CALL	PRTSTRD
@@ -1489,6 +1525,28 @@ HB_SPDTST:
 	CALL	PRTSTRD
 	.TEXT	"KB RAM$"
 ;
+#IF (CPUFAM == CPU_Z280)
+	CALL	NEWLINE
+	PRTS("Z280: $")
+	PRTS("MSR=$")
+	LD	C,$00			; MASTER STATUS REGISTER
+	;LDTCL	HL,(C)			; GET VALUE
+	.DB	$ED,$66
+	CALL	PRTHEXWORDHL
+	CALL	PC_SPACE
+	PRTS("BTCR=$")
+	LD	C,$02			; BUS TIMING AND CONTROL REGISTER
+	;LDTCL	HL,(C)			; GET VALUE
+	.DB	$ED,$66
+	CALL	PRTHEXWORDHL
+	CALL	PC_SPACE
+	PRTS("CCR=$")
+	LD	C,$12			; CACHE CONTROL REGISTER
+	;LDTCL	HL,(C)			; GET VALUE
+	.DB	$ED,$66
+	CALL	PRTHEXWORDHL
+#ENDIF
+;
 ; LOW BATTERY DIAGNOSTIC MESSAGE
 ;
 #IF (BATCOND)
@@ -2782,14 +2840,14 @@ SYS_SETSECS:
 ;
 SYS_PEEK:
 #IF (INTMODE == 1)
-	LD	A,I
+	;LD	A,I
 	DI
-	PUSH	AF
+	;PUSH	AF
 #ENDIF
 	CALL	HBX_PEEK		; IMPLEMENTED IN PROXY
 #IF (INTMODE == 1)
-	POP	AF
-	JP	PO,$+4
+	;POP	AF
+	;JP	PO,$+4
 	EI
 #ENDIF
 	XOR	A
@@ -2804,14 +2862,14 @@ SYS_PEEK:
 ;
 SYS_POKE:
 #IF (INTMODE == 1)
-	LD	A,I
+	;LD	A,I
 	DI
-	PUSH	AF
+	;PUSH	AF
 #ENDIF
 	CALL	HBX_POKE		; IMPLEMENTED IN PROXY
 #IF (INTMODE == 1)
-	POP	AF
-	JP	PO,$+4
+	;POP	AF
+	;JP	PO,$+4
 	EI
 #ENDIF
 	XOR	A
@@ -4261,10 +4319,11 @@ PS_PAD1:
 	DJNZ	PS_PAD1
 	RET
 ;
-HB_CPU_STR:	.TEXT	" Z80$"		; HB_STRZ80
-		.TEXT	" Z80180$"	; HB_STRZ180
-		.TEXT	" Z8S180-K$"	; HB_STRZS180K
-		.TEXT	" Z8S180-N$"	; HB_STRZS180N
+HB_CPU_STR:	.TEXT	" Z80$"
+		.TEXT	" Z80180$"
+		.TEXT	" Z8S180-K$"
+		.TEXT	" Z8S180-N$"
+		.TEXT	" Z80280$"
 ;
 PS_STRNUL	.TEXT	"--$"		; DISPLAY STRING FOR NUL VALUE
 ;

Source/HBIOS/z180.inc

@@ -64,4 +64,4 @@ Z180_BBR	.EQU	Z180_BASE + $39	; MMU BANK BASE REGISTER
 Z180_CBAR	.EQU	Z180_BASE + $3A	; MMU COMMON/BANK AREA REGISTER
 ;
 Z180_OMCR	.EQU	Z180_BASE + $3E	; OPERATION MODE CONTROL
-Z180_ICR	.EQU	$3F		; I/O CONTROL REGISTER (NOT RELOCATED!!!)
+Z180_ICR	.EQU	Z180_BASE + $3F	; I/O CONTROL REGISTER