Add RC2014 UART, Improve SD protocol fix

- RC2014 and related platforms will autodetect a UART at 0xA0 and 0xA8
- Ensure that CS fully brackets all SD I/O

Source/HBIOS/Config/RCZ180_ext.asm

@@ -34,8 +34,8 @@ Z180_CLKDIV	.SET	1		; Z180: CHK DIV: 0=OSC/2, 1=OSC, 2=OSC*2
 Z180_MEMWAIT	.SET	0		; Z180: MEMORY WAIT STATES (0-3)
 Z180_IOWAIT	.SET	1		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
 ;
+UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 ASCIENABLE	.SET	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
-;
 ACIAENABLE	.SET	FALSE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
 SIOENABLE	.SET	FALSE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
 ;

Source/HBIOS/Config/RCZ180_nat.asm

@@ -34,8 +34,8 @@ Z180_CLKDIV	.SET	1		; Z180: CHK DIV: 0=OSC/2, 1=OSC, 2=OSC*2
 Z180_MEMWAIT	.SET	0		; Z180: MEMORY WAIT STATES (0-3)
 Z180_IOWAIT	.SET	1		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
 ;
+UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 ASCIENABLE	.SET	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
-;
 ACIAENABLE	.SET	FALSE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
 SIOENABLE	.SET	FALSE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
 ;

Source/HBIOS/Config/RCZ80_std.asm

@@ -28,8 +28,8 @@
 ;
 CPUOSC		.SET	7372800		; CPU OSC FREQ IN MHZ
 ;
+UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 ACIAENABLE	.SET	TRUE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
-;
 SIOENABLE	.SET	TRUE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
 ;
 FDENABLE	.SET	FALSE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)

Source/HBIOS/Config/SCZ180_126.asm

@@ -36,10 +36,9 @@ Z180_IOWAIT	.SET	1		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
 ;
 HBIOS_MUTEX	.SET	FALSE		; ENABLE REENTRANT CALLS TO HBIOS (ADDS OVERHEAD)
 ;
+UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 ASCIENABLE	.SET	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
-;
 ACIAENABLE	.SET	FALSE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
-;
 SIOENABLE	.SET	FALSE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
 ;
 FDENABLE	.SET	FALSE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)

Source/HBIOS/Config/SCZ180_130.asm

@@ -43,10 +43,9 @@ DIAGENABLE	.SET	FALSE		; ENABLES OUTPUT TO 8 BIT LED DIAGNOSTIC PORT
 TIMRTCENABLE	.SET	TRUE		; ENABLE PERIODIC TIMER CLOCK DRIVER (TIMRTC.ASM)
 DSRTCENABLE	.SET	FALSE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
 ;
+UARTENABLE	.SET	FALSE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 ASCIENABLE	.SET	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
-;
 ACIAENABLE	.SET	FALSE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
-;
 SIOENABLE	.SET	FALSE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
 ;
 FDENABLE	.SET	FALSE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)

Source/HBIOS/Config/SCZ180_131.asm

@@ -43,10 +43,9 @@ DIAGENABLE	.SET	FALSE		; ENABLES OUTPUT TO 8 BIT LED DIAGNOSTIC PORT
 TIMRTCENABLE	.SET	TRUE		; ENABLE PERIODIC TIMER CLOCK DRIVER (TIMRTC.ASM)
 DSRTCENABLE	.SET	FALSE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
 ;
+UARTENABLE	.SET	FALSE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 ASCIENABLE	.SET	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
-;
 ACIAENABLE	.SET	FALSE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
-;
 SIOENABLE	.SET	FALSE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
 ;
 FDENABLE	.SET	FALSE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)

Source/HBIOS/cfg_ezz80.asm

@@ -70,7 +70,14 @@ DSRTCCHG	.EQU	FALSE		; DSRTC: FORCE BATTERY CHARGE ON (USE WITH CAUTION!!!)
 BQRTCENABLE	.EQU	FALSE		; BQRTC: ENABLE BQ4845 CLOCK DRIVER (BQRTC.ASM)
 BQRTC_BASE	.EQU	$50		; BQRTC: I/O BASE ADDRESS
 ;
-UARTENABLE	.EQU	FALSE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+UARTENABLE	.EQU	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
+UARTCFG		.EQU	DEFSERCFG	; UART: LINE CONFIG FOR UART PORTS
+UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
+UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
+UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
+UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;

Source/HBIOS/cfg_master.asm

@@ -100,6 +100,7 @@ UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
 UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
+UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCI0CFG	.EQU	DEFSERCFG	; ASCI 0: SERIAL LINE CONFIG

Source/HBIOS/cfg_mk4.asm

@@ -85,6 +85,7 @@ UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
 UARTCAS		.EQU	TRUE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	TRUE		; UART: AUTO-DETECT 4UART UART
+UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCI0CFG	.EQU	DEFSERCFG	; ASCI 0: SERIAL LINE CONFIG

Source/HBIOS/cfg_n8.asm

@@ -88,6 +88,7 @@ UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
 UARTCAS		.EQU	TRUE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	TRUE		; UART: AUTO-DETECT 4UART UART
+UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCI0CFG	.EQU	DEFSERCFG	; ASCI 0: SERIAL LINE CONFIG

Source/HBIOS/cfg_rcz180.asm

@@ -73,7 +73,14 @@ DSRTCCHG	.EQU	FALSE		; DSRTC: FORCE BATTERY CHARGE ON (USE WITH CAUTION!!!)
 BQRTCENABLE	.EQU	FALSE		; BQRTC: ENABLE BQ4845 CLOCK DRIVER (BQRTC.ASM)
 BQRTC_BASE	.EQU	$50		; BQRTC: I/O BASE ADDRESS
 ;
-UARTENABLE	.EQU	FALSE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+UARTENABLE	.EQU	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
+UARTCFG		.EQU	DEFSERCFG	; UART: LINE CONFIG FOR UART PORTS
+UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
+UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
+UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
+UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCI0CFG	.EQU	DEFSERCFG	; ASCI 0: SERIAL LINE CONFIG

Source/HBIOS/cfg_rcz80.asm

@@ -69,7 +69,14 @@ DSRTCCHG	.EQU	FALSE		; DSRTC: FORCE BATTERY CHARGE ON (USE WITH CAUTION!!!)
 BQRTCENABLE	.EQU	FALSE		; BQRTC: ENABLE BQ4845 CLOCK DRIVER (BQRTC.ASM)
 BQRTC_BASE	.EQU	$50		; BQRTC: I/O BASE ADDRESS
 ;
-UARTENABLE	.EQU	FALSE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+UARTENABLE	.EQU	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
+UARTCFG		.EQU	DEFSERCFG	; UART: LINE CONFIG FOR UART PORTS
+UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
+UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
+UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
+UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;

Source/HBIOS/cfg_sbc.asm

@@ -79,6 +79,7 @@ UARTSBC		.EQU	TRUE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
 UARTCAS		.EQU	TRUE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	TRUE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	TRUE		; UART: AUTO-DETECT 4UART UART
+UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;

Source/HBIOS/cfg_scz180.asm

@@ -68,7 +68,14 @@ DSRTCCHG	.EQU	FALSE		; DSRTC: FORCE BATTERY CHARGE ON (USE WITH CAUTION!!!)
 BQRTCENABLE	.EQU	FALSE		; BQRTC: ENABLE BQ4845 CLOCK DRIVER (BQRTC.ASM)
 BQRTC_BASE	.EQU	$50		; BQRTC: I/O BASE ADDRESS
 ;
-UARTENABLE	.EQU	FALSE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+UARTENABLE	.EQU	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
+UARTCFG		.EQU	DEFSERCFG	; UART: LINE CONFIG FOR UART PORTS
+UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
+UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
+UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
+UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCI0CFG	.EQU	DEFSERCFG	; ASCI 0: SERIAL LINE CONFIG

Source/HBIOS/cfg_zeta.asm

@@ -73,6 +73,7 @@ UARTSBC		.EQU	TRUE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
 UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
+UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;

Source/HBIOS/cfg_zeta2.asm

@@ -78,6 +78,7 @@ UARTSBC		.EQU	TRUE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
 UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
+UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;

Source/HBIOS/dbgmon.asm

@@ -31,7 +31,10 @@ BUFLEN	.EQU	40			; INPUT LINE LENGTH
 	JP	DSKY_ENTRY
 	JP	UART_ENTRY
 ;
-;#DEFINE USEDELAY
+#IF DSKYENABLE
+  #DEFINE USEDELAY
+#ENDIF
+;
 #INCLUDE "util.asm"
 ;
 ;__UART_ENTRY_________________________________________________________________

Source/HBIOS/dsrtc.asm

@@ -120,6 +120,8 @@ DSRTC_IDLE	.EQU	%00101000	; QUIESCENT STATE
 ;
 #ENDIF
 ;
+RTCDEF		.SET	DSRTC_IDLE	; FOR HBIOS MAINLINE
+;
 DSRTC_BUFSIZ	.EQU	7		; 7 BYTE BUFFER (YYMMDDHHMMSSWW)
 ;
 ; RTC DEVICE PRE-INITIALIZATION ENTRY
@@ -129,7 +131,7 @@ DSRTC_PREINIT:
 	; SET RELEVANT BITS IN RTC LATCH SHADOW REGISTER
 	; TO THEIR QUIESENT STATE
 	LD	A,(RTCVAL)		; GET CURRENT SHADOW REG VAL
-	AND	DSRTC_MASK		; CLEAR OUR BITS
+	AND	~DSRTC_MASK		; CLEAR OUR BITS
 	OR	DSRTC_IDLE		; SET OUR IDLE BITS
 	LD	(RTCVAL),A		; SAVE IT
 ;

Source/HBIOS/hbios.asm

@@ -132,6 +132,12 @@ CTCC		.EQU	CTCBASE + 2	; CTC: CHANNEL C REGISTER ADR
 CTCD		.EQU	CTCBASE + 3	; CTC: CHANNEL D REGISTER ADR
 #ENDIF
 ;
+; THIS EQUATE IS UPDATED BY DRIVER INCLUDES THAT SHARE THE RTC LATCH.
+; AS DRIVER IS INCLUDED, IT WILL USE .SET TO SET ANY BITS THEY OWN
+; AND WANT TO SET AS DEFAULT.
+;
+RTCDEF		.EQU	0		; ALLOWS DRIVERS TO SET BITS
+;
 ;
 ;
 #IFNDEF	APPBOOT
@@ -4100,7 +4106,7 @@ HB_SECS		.FILL	4,0		; 32 BIT SECONDS COUNTER
 ;
 HB_CPUTYPE	.DB	0		; 0=Z80, 1=80180, 2=SL1960, 3=ASCI BRG
 ;
-RTCVAL		.DB	0		; SHADOW VALUE FOR RTC LATCH PORT
+RTCVAL		.DB	RTCDEF		; SHADOW VALUE FOR RTC LATCH PORT
 ;
 HB_BATCOND	.DB	0		; BATTERY CONDITION (0=LOW, 1=OK)
 ;

Source/HBIOS/sd.asm

@@ -119,31 +119,40 @@ SD_NOPULLUP	.EQU	TRUE		; ASSUME NO PULLUP
 SD_DEVCNT	.EQU	1		; NUMBER OF PHYSICAL UNITS (SOCKETS)
 SD_OPRREG	.EQU	RTCIO		; USES RTC LATCHES FOR OPERATION
 SD_OPRDEF	.EQU	%00000001	; QUIESCENT STATE
+SD_OPRMSK	.EQU	%10000111	; MASK FOR BITS WE OWN IN RTC LATCH PORT
 SD_INPREG	.EQU	RTCIO		; INPUT REGISTER IS RTC
 SD_CS0		.EQU	%00000100	; RTC:2 IS SELECT
 SD_CLK		.EQU	%00000010	; RTC:1 IS CLOCK
 SD_DI		.EQU	%00000001	; RTC:0 IS DATA IN (CARD <- CPU)
 SD_DO		.EQU	%10000000	; RTC:7 IS DATA OUT (CARD -> CPU)
+;
+RTCDEF		.SET	SD_OPRDEF	; SET DEFAULT IN HBIOS MAINLINE
 #ENDIF
 ;
 #IF (SDMODE == SDMODE_N8)		; UNMODIFIED N8-2511
 SD_DEVCNT	.EQU	1		; NUMBER OF PHYSICAL UNITS (SOCKETS)
 SD_OPRREG	.EQU	RTCIO		; USES RTC LATCHES FOR OPERATION
 SD_OPRDEF	.EQU	%00000001	; QUIESCENT STATE
+SD_OPRMSK	.EQU	%01000111	; MASK FOR BITS WE OWN IN RTC LATCH PORT
 SD_INPREG	.EQU	RTCIO		; INPUT REGISTER IS RTC
 SD_CS0		.EQU	%00000100	; RTC:2 IS SELECT
 SD_CLK		.EQU	%00000010	; RTC:1 IS CLOCK
 SD_DI		.EQU	%00000001	; RTC:0 IS DATA IN (CARD <- CPU)
 SD_DO		.EQU	%01000000	; RTC:6 IS DATA OUT (CARD -> CPU)
+;
+RTCDEF		.SET	SD_OPRDEF	; SET DEFAULT IN HBIOS MAINLINE
 #ENDIF
 ;
 #IF (SDMODE == SDMODE_CSIO)		; N8-2312
 SD_DEVCNT	.EQU	1		; NUMBER OF PHYSICAL UNITS (SOCKETS)
 SD_OPRREG	.EQU	RTCIO		; USES RTC LATCHES FOR OPERATION
 SD_OPRDEF	.EQU	%00000000	; QUIESCENT STATE
+SD_OPRMSK	.EQU	%00000100	; MASK FOR BITS WE OWN IN RTC LATCH PORT
 SD_CS0		.EQU	%00000100	; RTC:2 IS SELECT
 SD_CNTR		.EQU	Z180_CNTR
 SD_TRDR		.EQU	Z180_TRDR
+;
+RTCDEF		.SET	SD_OPRDEF	; SET DEFAULT IN HBIOS MAINLINE
 #ENDIF
 ;
 #IF (SDMODE == SDMODE_PPI)		; PPISD
@@ -165,6 +174,7 @@ SD_DO		.EQU	%10000000	; PPIB:7 IS DATA OUT (CARD -> CPU)
 SD_DEVCNT	.EQU	1		; NUMBER OF PHYSICAL UNITS (SOCKETS)
 SD_OPRREG	.EQU	SIO_MCR		; UART MCR PORT (OUTPUT: CS, CLK, DIN)
 SD_OPRDEF	.EQU	%00001100	; QUIESCENT STATE
+SD_OPRMSK	.EQU	%00101101	; MASK FOR BITS WE OWN IN RTC LATCH PORT
 SD_INPREG	.EQU	SIO_MSR		; INPUT REGISTER IS MSR
 SD_CS0		.EQU	%00001000	; UART MCR:3 IS SELECT
 SD_CLK		.EQU	%00000100	; UART MCR:2 IS CLOCK
@@ -198,10 +208,13 @@ SD_TRDR		.EQU	Z180_TRDR
 SD_DEVCNT	.EQU	SDCNT		; NUMBER OF PHYSICAL UNITS (SOCKETS)
 SD_OPRREG	.EQU	RTCIO		; USES RTC LATCHES FOR OPERATION
 SD_OPRDEF	.EQU	%00001100	; QUIESCENT STATE (/CS1 & /CS2 DEASSERTED)
+SD_OPRMSK	.EQU	%00001100	; MASK FOR BITS WE OWN IN RTC LATCH PORT
 SD_CS0		.EQU	%00000100	; RTC:2 IS SELECT FOR PRIMARY SPI CARD
 SD_CS1		.EQU	%00001000	; RTC:3 IS SELECT FOR SECONDARY SPI CARD
 SD_CNTR		.EQU	Z180_CNTR
 SD_TRDR		.EQU	Z180_TRDR
+;
+RTCDEF		.SET	SD_OPRDEF	; SET DEFAULT IN HBIOS MAINLINE
 #ENDIF
 ;
 #IF (SDMODE == SDMODE_MT)		; MT shift register for RC2014 (ref SDMODE_CSIO)
@@ -318,6 +331,7 @@ SD_INIT:
 	CALL	PRTHEXBYTE
 ;
 	LD	A,(RTCVAL)		; GET RTC PORT SHADOW VALUE
+	AND	~SD_OPRMSK		; CLEAR OUR BITS
 	OR	SD_OPRDEF		; SET OUR BIT DEFAULTS
 	LD	(RTCVAL),A		; SAVE IT
 #ENDIF
@@ -329,6 +343,7 @@ SD_INIT:
 	CALL	PRTHEXBYTE
 ;
 	LD	A,(RTCVAL)		; GET RTC PORT SHADOW VALUE
+	AND	~SD_OPRMSK		; CLEAR OUR BITS
 	OR	SD_OPRDEF		; SET OUR BIT DEFAULTS
 	LD	(RTCVAL),A		; SAVE IT
 #ENDIF
@@ -349,6 +364,7 @@ SD_INIT:
 	CALL	PRTHEXBYTE
 ;
 	LD	A,(RTCVAL)		; GET RTC PORT SHADOW VALUE
+	AND	~SD_OPRMSK		; CLEAR OUR BITS
 	OR	SD_OPRDEF		; SET OUR BIT DEFAULTS
 	LD	(RTCVAL),A		; SAVE IT
 #ENDIF
@@ -412,6 +428,7 @@ SD_INIT:
 	CALL	PRTHEXBYTE
 ;
 	LD	A,(RTCVAL)		; GET RTC PORT SHADOW VALUE
+	AND	~SD_OPRMSK		; CLEAR OUR BITS
 	OR	SD_OPRDEF		; SET OUR BIT DEFAULTS
 	LD	(RTCVAL),A		; SAVE IT
 #ENDIF
@@ -844,6 +861,12 @@ SD_INITCARD1:
 	CALL	SD_PUT			; SEND 8 CLOCKS
 	POP	BC			; RESTORE LOOP CONTROL
 	DJNZ	SD_INITCARD1		; LOOP AS NEEDED
+;
+	; MAKE SURE WE FINISH SENDING
+#IF ((SDMODE == SDMODE_CSIO) | (SDMODE == SDMODE_MK4) | (SDMODE == SDMODE_SC))
+	CALL	SD_WAITTX		; WAIT FOR TE TO CLEAR
+	CALL	DLY4			; WAIT A BIT MORE FOR FINAL BIT
+#ENDIF
 ;
 	; PUT CARD IN IDLE STATE
 	CALL	SD_GOIDLE		; GO TO IDLE
@@ -1538,8 +1561,8 @@ SD_SETUP:
 ;
 #IF ((SDMODE == SDMODE_CSIO) | (SDMODE == SDMODE_MK4) | (SDMODE == SDMODE_SC))
 	; CSIO SETUP FOR Z180 CSIO
-;	LD	A,2			; 18MHz/20 <= 400kHz
-	LD	A,6			; ???
+;	LD	A,2			; DIV 80, 225KHZ @ 18MHZ CLK
+	LD	A,6			; DIV 1280, 14KHZ @ 18MHZ CLK
 	OUT0	(SD_CNTR),A
 #ENDIF
 ;
@@ -1556,7 +1579,6 @@ SD_SETUP:
 #ENDIF
 ;
 #IF (SDMODE == SDMODE_UART)
-SD_OPRMSK	.EQU	(SD_CS0 | SD_CLK | SD_DI)
 	IN	A,(SD_OPRREG)		; OPRREG == SIO_MCR
 	AND	~SD_OPRMSK		; MASK OFF SD CONTROL BITS
 	OR	SD_OPRDEF		; SET DEFAULT BITS
@@ -1605,9 +1627,10 @@ SD_CHKWP:
 ; SELECT CARD
 ;
 SD_SELECT:
-#IF ((SDMODE == SDMODE_CSIO) | (SDMODE == SDMODE_MK4) | (SDMODE == SDMODE_SC))
-	CALL	SD_WAITTX
-#ENDIF
+;	; FINISH SENDING BEFORE ASSERTING CS!
+;#IF ((SDMODE == SDMODE_CSIO) | (SDMODE == SDMODE_MK4) | (SDMODE == SDMODE_SC))
+;	CALL	SD_WAITTX
+;#ENDIF
 ;
 	LD	A,(IY+SD_DEV)		; GET CURRENT DEVICE
 	OR	A			; SET FLAGS
@@ -1641,6 +1664,22 @@ SD_SELECT2:
 ; DESELECT CARD
 ;
 SD_DESELECT:
+#IF ((SDMODE == SDMODE_CSIO) | (SDMODE == SDMODE_MK4) | (SDMODE == SDMODE_SC))
+	; DON'T REMOVE CS UNTIL WE ARE DONE SENDING!
+	CALL	SD_WAITTX		; WAIT FOR TE TO CLEAR
+;
+	; ACCORDING TO Z180 DOCS, IT MAY TAKE UP TO 1 BIT TIME TO
+	; FINISH SENDING AFTER TE IS CLEARED.  THE DELAY BELOW WILL
+	; DO THIS FOR THE SLOWEST POSSIBLE SEND RATE WHICH IS
+	; CLK / 1320, SO DELAY AT LEAST 1320 T-STATES
+	;CALL	DLY64			; DELAY FOR FINAL BIT
+;
+	; IN PRACTICE, IT LOOKS LIKE THIS WORST CASE SCENARIO NEVER
+	; OCCURS.  FOR NOW, USE A SMALL DELAY WHICH SEEMS TO BE MORE
+	; THAN ADEQUATE BASED ON LOGIC ANALYZER TRACES.
+	CALL	DLY4			; DELAY FOR FINAL BIT
+#ENDIF
+;
 	LD	A,(SD_OPRVAL)
 #IF (SD_DEVCNT > 1)
 	AND	~(SD_CS0 | SD_CS1)

Source/HBIOS/uart.asm

@@ -626,5 +626,21 @@ UART_CFG:
 	.DW	UARTCFG				; LINE CONFIGURATION
 	.FILL	2,$FF				; FILLER
 #ENDIF
+#IF (UARTRC)
+	; UARTRC SERIAL PORT A
+	.DB	0				; DEVICE NUMBER (UPDATED DURING INIT)
+	.DB	0				; UART TYPE
+	.DB	$A0				; IO PORT BASE (RBR, THR)
+	.DB	$A0 + UART_LSR			; LINE STATUS PORT (LSR)
+	.DW	UARTCFG				; LINE CONFIGURATION
+	.FILL	2,$FF				; FILLER
+	; UARTRC SERIAL PORT B
+	.DB	0				; DEVICE NUMBER (UPDATED DURING INIT)
+	.DB	0				; UART TYPE
+	.DB	$A8				; IO PORT BASE (RBR, THR)
+	.DB	$A8 + UART_LSR			; LINE STATUS PORT (LSR)
+	.DW	UARTCFG				; LINE CONFIGURATION
+	.FILL	2,$FF				; FILLER
+#ENDIF
 ;
 UART_CNT	.EQU	($ - UART_CFG) / 8

Source/ver.inc

@@ -2,4 +2,4 @@
 #DEFINE	RMN	1
 #DEFINE	RUP	0
 #DEFINE	RTP	0
-#DEFINE BIOSVER	"3.1-pre.0"
+#DEFINE BIOSVER	"3.1-pre.1"

Source/ver.lib

@@ -3,5 +3,5 @@ rmn	equ	1
 rup	equ	0
 rtp	equ	0
 biosver	macro
-	db	"3.1-pre.0"
+	db	"3.1-pre.1"
 	endm