diff --git a/Source/HBIOS/Config/RCZ280_zz80mb.asm b/Source/HBIOS/Config/RCZ280_zz80mb.asm
index 88fbd454..5d56493c 100644
--- a/Source/HBIOS/Config/RCZ280_zz80mb.asm
+++ b/Source/HBIOS/Config/RCZ280_zz80mb.asm
@@ -28,7 +28,7 @@
 ;
 #include "cfg_rcz280.asm"
 ;
-CPUOSC		.SET	12000000	; CPU OSC FREQ IN MHZ
+CPUOSC		.SET	24000000	; CPU OSC FREQ IN MHZ
 INTMODE		.SET	3		; INTERRUPTS: 0=NONE, 1=MODE 1, 2=MODE 2
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
 ;
diff --git a/Source/HBIOS/hbios.asm b/Source/HBIOS/hbios.asm
index fcddd3df..ea18756c 100644
--- a/Source/HBIOS/hbios.asm
+++ b/Source/HBIOS/hbios.asm
@@ -2772,6 +2772,7 @@ HB_WDZ:
 ;
 	LD	A,(CB_CONDEV)		; GET CURRENT CONSOLE
 	LD	(HB_NEWCON),A		; AND INIT NEW CONSOLE VAR
+;
 #IF CRTACT
 ;
 ; BIOS IS CONFIGURED TO AUTO ACTIVATE CRT DEVICE.  FIRST,
@@ -2795,11 +2796,6 @@ HB_WDZ:
 ;
 #ENDIF
 ;
-; THIS IS A GOOD PLACE TO DETERMINE IF FRONT PANEL HARDWARE REALLY
-; EXISTS.
-;
-	CALL	FP_DETECT
-;
 #IF (FPSW_ENABLE)
 ;
 ; IF WE HAVE FRONT PANEL SWITCHES, THIS IS THE RIGHT PLACE TO HANDLE
@@ -2813,8 +2809,9 @@ HB_WDZ:
 	LD	A,FPSW_IO
 	CALL	PRTHEXBYTE
 ;
-	; THE EXISTENCE OF THE FP WAS TESTED EARLIER.  IF IT DOESN'T
-	; EXIST, BAIL OUT.
+	CALL	FP_DETECT
+;
+	; IF FP DOESN'T EXIST, BAIL OUT.
 	LD	A,(FPSW_ACTIVE)		; GET FP EXISTENCE FLAG
 	OR	A			; SET FLAGS
 	JR	NZ,HB_FP1		; IF WE HAVE ONE, CONTINUE
@@ -5114,6 +5111,99 @@ SYS_INTSET1:
 	RET				; DONE
 ;
 ;==================================================================================================
+;   Z280 INTERRUPT VECTOR TABLE
+;==================================================================================================
+;
+#IF (MEMMGR == MM_Z280)
+;
+	; THE Z280 IVT MUST BE ON A 4K BOUNDARY.  IT HAS BEEN LOCATED
+	; HERE IN AN EFFORT TO MINIMIZE WASTED SPACE.  THERE SHOULD BE
+	; A LITTLE LESS THAN 4K OF CODE ABOVE.
+;
+Z280_IVT_SLACK	.EQU	$1000 - ($ & $FFF)
+		.ECHO	"Z280 IVT SLACK occupies "
+		.ECHO	Z280_IVT_SLACK
+		.ECHO	" bytes.\n"
+		;.FILL	$1000 - ($ & $FFF)	; MUST BE 4K ALIGNED!
+		.FILL	Z280_IVT_SLACK		; MUST BE 4K ALIGNED!
+;
+Z280_IVT:
+	.DW	0, 0			; RESERVED
+	.DW	0			; NMI MSR
+	.DW	0			; NMI VECTOR
+	.DW	$0000			; INT A MSR
+	.DW	Z280_BADINT		; INT A VECTOR
+	.DW	$0000			; INT B MSR
+	.DW	Z280_BADINT		; INT B VECTOR
+	.DW	$0000			; INT C MSR
+	.DW	Z280_BADINT		; INT C VECTOR
+	.DW	$0000			; COUNTER/TIMER 0 MSR
+	.DW	Z280_BADINT		; COUNTER/TIMER 0 VECTOR
+	.DW	$0000			; COUNTER/TIMER 1 MSR
+	.DW	Z280_BADINT		; COUNTER/TIMER 1 VECTOR
+	.DW	0, 0			; RESERVED
+	.DW	$0000			; COUNTER/TIMER 2 MSR
+	.DW	Z280_BADINT		; COUNTER/TIMER 2 VECTOR
+	.DW	$0000			; DMA CHANNEL 0 MSR
+	.DW	Z280_BADINT		; DMA CHANNEL 0 VECTOR
+	.DW	$0000			; DMA CHANNEL 1 MSR
+	.DW	Z280_BADINT		; DMA CHANNEL 1 VECTOR
+	.DW	$0000			; DMA CHANNEL 2 MSR
+	.DW	Z280_BADINT		; DMA CHANNEL 2 VECTOR
+	.DW	$0000			; DMA CHANNEL 3 MSR
+	.DW	Z280_BADINT		; DMA CHANNEL 3 VECTOR
+	.DW	$0000			; UART RECEIVER MSR
+	.DW	Z280_BADINT		; UART RECEIVER VECTOR
+	.DW	$0000			; UART TRANSMITTER MSR
+	.DW	Z280_BADINT		; UART TRANSMITTER VECTOR
+	.DW	$0000			; SINGLE STEP TRAP MSR
+	.DW	Z280_SSTEP		; SINGLE STEP TRAP VECTOR
+	.DW	$0000			; BREAK ON HALT TRAP MSR
+	.DW	Z280_BRKHLT		; BREAK ON HALT TRAP VECTOR
+	.DW	$0000			; DIVISION EXCEPTION TRAP MSR
+	.DW	Z280_DIVEXC		; DIVISION EXCEPTION TRAP VECTOR
+	.DW	$0000			; STACK OVERFLOW WARNING TRAP MSR
+	.DW	Z280_STKOVR		; STACK OVERFLOW WARNING TRAP VECTOR
+	.DW	$0000			; ACCESS VIOLATION TRAP MSR
+	.DW	Z280_ACCVIO		; ACCESS VIOLATION TRAP VECTOR
+	.DW	$0000			; SYSTEM CALL TRAP MSR
+	.DW	Z280_SYSCALL		; SYSTEM CALL TRAP VECTOR
+	.DW	$0000			; PRIVILEGED INSTRUCTION TRAP MSR
+	.DW	Z280_PRIVINST		; PRIVILEGED INSTRUCTION TRAP VECTOR
+	.DW	$0000			; EPU <- MEMORY EXTENDED INSTRUCTION TRAP MSR
+	.DW	$0000			; EPU <- MEMORY EXTENDED INSTRUCTION TRAP VECTOR
+	.DW	$0000			; MEMORY <- EPU EXTENDED INSTRUCTION TRAP MSR
+	.DW	$0000			; MEMORY <- EPU EXTENDED INSTRUCTION TRAP VECTOR
+	.DW	$0000			; A <- EPU EXTENDED INSTRUCTION TRAP MSR
+	.DW	$0000			; A <- EPU EXTENDED INSTRUCTION TRAP VECTOR
+	.DW	$0000			; EPU INTERNAL OPERATION EXTENDED INSTRUCTION TRAP MSR
+	.DW	$0000			; EPU INTERNAL OPERATION EXTENDED INSTRUCTION TRAP VECTOR
+	.DW	0, 0			; RESERVED
+	.DW	0, 0			; RESERVED
+	; PROGRAM COUNTER VALUES FOR NMI/INTA (16)
+	.DW	HBX_IV00
+	.DW	HBX_IV01
+	.DW	HBX_IV02
+	.DW	HBX_IV03
+	.DW	HBX_IV04
+	.DW	HBX_IV05
+	.DW	HBX_IV06
+	.DW	HBX_IV07
+	.DW	HBX_IV08
+	.DW	HBX_IV09
+	.DW	HBX_IV0A
+	.DW	HBX_IV0B
+	.DW	HBX_IV0C
+	.DW	HBX_IV0D
+	.DW	HBX_IV0E
+	.DW	HBX_IV0F
+	; THE REMAINDER OF THE Z280 IVT IS TRUNCATED HERE BECAUSE IT
+	; TAKES A BUNCH OF SPACE AND IS NOT USED.  WE SUPPORT ONLY
+	; 16 VECTORED INTERRUPTS AND THEY MUST BE CONNECTED TO INTA.
+;
+#ENDIF
+;
+;==================================================================================================
 ;   GLOBAL HBIOS FUNCTIONS
 ;==================================================================================================
 ;
@@ -5673,94 +5763,6 @@ HB_ALLOC1:
 HB_TMPSZ	.DW	0
 HB_TMPREF	.DW	0
 ;
-;==================================================================================================
-;   Z280 INTERRUPT VECTOR TABLE
-;==================================================================================================
-;
-#IF (MEMMGR == MM_Z280)
-;
-	; THE Z280 IVT MUST BE ON A 4K BOUNDARY.  IT HAS BEEN LOCATED
-	; HERE IN AN EFFORT TO MINIMIZE WASTED SPACE.  THERE SHOULD BE
-	; A LITTLE LESS THAN 4K OF CODE ABOVE.
-;
-	.FILL	$1000 - ($ & $FFF)	; MUST BE 4K ALIGNED!
-;
-Z280_IVT:
-	.DW	0, 0			; RESERVED
-	.DW	0			; NMI MSR
-	.DW	0			; NMI VECTOR
-	.DW	$0000			; INT A MSR
-	.DW	Z280_BADINT		; INT A VECTOR
-	.DW	$0000			; INT B MSR
-	.DW	Z280_BADINT		; INT B VECTOR
-	.DW	$0000			; INT C MSR
-	.DW	Z280_BADINT		; INT C VECTOR
-	.DW	$0000			; COUNTER/TIMER 0 MSR
-	.DW	Z280_BADINT		; COUNTER/TIMER 0 VECTOR
-	.DW	$0000			; COUNTER/TIMER 1 MSR
-	.DW	Z280_BADINT		; COUNTER/TIMER 1 VECTOR
-	.DW	0, 0			; RESERVED
-	.DW	$0000			; COUNTER/TIMER 2 MSR
-	.DW	Z280_BADINT		; COUNTER/TIMER 2 VECTOR
-	.DW	$0000			; DMA CHANNEL 0 MSR
-	.DW	Z280_BADINT		; DMA CHANNEL 0 VECTOR
-	.DW	$0000			; DMA CHANNEL 1 MSR
-	.DW	Z280_BADINT		; DMA CHANNEL 1 VECTOR
-	.DW	$0000			; DMA CHANNEL 2 MSR
-	.DW	Z280_BADINT		; DMA CHANNEL 2 VECTOR
-	.DW	$0000			; DMA CHANNEL 3 MSR
-	.DW	Z280_BADINT		; DMA CHANNEL 3 VECTOR
-	.DW	$0000			; UART RECEIVER MSR
-	.DW	Z280_BADINT		; UART RECEIVER VECTOR
-	.DW	$0000			; UART TRANSMITTER MSR
-	.DW	Z280_BADINT		; UART TRANSMITTER VECTOR
-	.DW	$0000			; SINGLE STEP TRAP MSR
-	.DW	Z280_SSTEP		; SINGLE STEP TRAP VECTOR
-	.DW	$0000			; BREAK ON HALT TRAP MSR
-	.DW	Z280_BRKHLT		; BREAK ON HALT TRAP VECTOR
-	.DW	$0000			; DIVISION EXCEPTION TRAP MSR
-	.DW	Z280_DIVEXC		; DIVISION EXCEPTION TRAP VECTOR
-	.DW	$0000			; STACK OVERFLOW WARNING TRAP MSR
-	.DW	Z280_STKOVR		; STACK OVERFLOW WARNING TRAP VECTOR
-	.DW	$0000			; ACCESS VIOLATION TRAP MSR
-	.DW	Z280_ACCVIO		; ACCESS VIOLATION TRAP VECTOR
-	.DW	$0000			; SYSTEM CALL TRAP MSR
-	.DW	Z280_SYSCALL		; SYSTEM CALL TRAP VECTOR
-	.DW	$0000			; PRIVILEGED INSTRUCTION TRAP MSR
-	.DW	Z280_PRIVINST		; PRIVILEGED INSTRUCTION TRAP VECTOR
-	.DW	$0000			; EPU <- MEMORY EXTENDED INSTRUCTION TRAP MSR
-	.DW	$0000			; EPU <- MEMORY EXTENDED INSTRUCTION TRAP VECTOR
-	.DW	$0000			; MEMORY <- EPU EXTENDED INSTRUCTION TRAP MSR
-	.DW	$0000			; MEMORY <- EPU EXTENDED INSTRUCTION TRAP VECTOR
-	.DW	$0000			; A <- EPU EXTENDED INSTRUCTION TRAP MSR
-	.DW	$0000			; A <- EPU EXTENDED INSTRUCTION TRAP VECTOR
-	.DW	$0000			; EPU INTERNAL OPERATION EXTENDED INSTRUCTION TRAP MSR
-	.DW	$0000			; EPU INTERNAL OPERATION EXTENDED INSTRUCTION TRAP VECTOR
-	.DW	0, 0			; RESERVED
-	.DW	0, 0			; RESERVED
-	; PROGRAM COUNTER VALUES FOR NMI/INTA (16)
-	.DW	HBX_IV00
-	.DW	HBX_IV01
-	.DW	HBX_IV02
-	.DW	HBX_IV03
-	.DW	HBX_IV04
-	.DW	HBX_IV05
-	.DW	HBX_IV06
-	.DW	HBX_IV07
-	.DW	HBX_IV08
-	.DW	HBX_IV09
-	.DW	HBX_IV0A
-	.DW	HBX_IV0B
-	.DW	HBX_IV0C
-	.DW	HBX_IV0D
-	.DW	HBX_IV0E
-	.DW	HBX_IV0F
-	; THE REMAINDER OF THE Z280 IVT IS TRUNCATED HERE BECAUSE IT
-	; TAKES A BUNCH OF SPACE AND IS NOT USED.  WE SUPPORT ONLY
-	; 16 VECTORED INTERRUPTS AND THEY MUST BE CONNECTED TO INTA.
-;
-#ENDIF
-;
 ; Z280 BANK SELECTION (CALLED FROM PROXY)
 ;
 #IF (MEMMGR == MM_Z280)
diff --git a/Source/HBIOS/sd.asm b/Source/HBIOS/sd.asm
index 3207b64b..d6499552 100644
--- a/Source/HBIOS/sd.asm
+++ b/Source/HBIOS/sd.asm
@@ -9,14 +9,14 @@
 ;	- TEST XC CARD TYPE DETECTION
 ;	- TRY TO GET INIT TO FAIL, REMOVE DELAYS AT START OF GOIDLE?
 ;
-;----------------------------------------------------------------------------------------------
-; SD Signal	Active	JUHA	N8	CSIO	PPI	UART	DSD	MK4	SC	MT
-; ------------	------- ------- ------- ------- ------- ------- ------- -------	-------	-------
-; CS (DAT3)	LO ->	RTC:2	RTC:2	RTC:2	~PC:4	~MCR:3	OPR:2	SD:2	~RTC:2/3OPR:4/5
-; CLK		HI ->	RTC:1	RTC:1	CSIO	PC:1	~MCR:2	OPR:1	CSIO	CSIO	SPI
-; DI (CMD)	HI ->	RTC:0	RTC:0	CSIO	PC:0	~MCR:0	OPR:0	CSIO	CSIO	SPI
-; DO (DAT0)	HI ->	RTC:7	RTC:6	CSIO	PB:7	~MSR:5	OPR:0	CSIO	CSIO	SPI
-;----------------------------------------------------------------------------------------------
+;-----------------------------------------------------------------------------------------------------
+; SD Signal	Active	JUHA	N8	CSIO	PPI	UART	DSD	MK4	SC	MT     PIO
+; ------------	------- ------- ------- ------- ------- ------- ------- -------	-------	--------------
+; CS (DAT3)	LO ->	RTC:2	RTC:2	RTC:2	~PC:4	~MCR:3	OPR:2	SD:2	~RTC:2/3OPR:4/5~OPR:3
+; CLK		HI ->	RTC:1	RTC:1	CSIO	PC:1	~MCR:2	OPR:1	CSIO	CSIO	SPI    OPR:4
+; DI (CMD)	HI ->	RTC:0	RTC:0	CSIO	PC:0	~MCR:0	OPR:0	CSIO	CSIO	SPI    OPR:0
+; DO (DAT0)	HI ->	RTC:7	RTC:6	CSIO	PB:7	~MSR:5	OPR:0	CSIO	CSIO	SPI    OPR:7
+;-----------------------------------------------------------------------------------------------------
 ;
 ; CS = CHIP SELECT (AKA DAT3 FOR NON-SPI MODE)
 ; CLK = CLOCK
@@ -167,6 +167,7 @@ RTCDEF		.SET	RTCDEF | SD_OPRDEF	; SET DEFAULT IN HBIOS MAINLINE
 SD_DEVMAX	.EQU	1		; NUMBER OF PHYSICAL UNITS (SOCKETS)
 SD_PPIBASE	.EQU	SDPPIBASE	; BASE IO PORT FOR PPI
 SD_PPIB		.EQU	SDPPIBASE + 1	; PPI PORT B (INPUT: DOUT)
+SD_PPIB		.EQU	SDPPIBASE + 1	; PPI PORT B (INPUT: DOUT)
 SD_PPIC		.EQU	SDPPIBASE + 2	; PPI PORT C (OUTPUT: CS, CLK, DIN)
 SD_PPIX		.EQU	SDPPIBASE + 3	; PPI CONTROL PORT
 SD_OPRREG	.EQU	SD_PPIC		; PPI PORT C IS OPR REG
@@ -298,7 +299,10 @@ SD_INVCS	.EQU	FALSE		; INVERT CS
 SD_DEVMAX	.EQU	1		; NUMBER OF PHYSICAL UNITS (SOCKETS)
 SD_IOBASE	.EQU	$69		; IO BASE ADDRESS FOR SD INTERFACE
 SD_OPRREG	.EQU	SD_IOBASE	; OUTPUT PORT (OUTPUT: CS, CLK, DIN)
-SD_OPRDEF	.EQU	%11111111	; OUTPUT PORT DEFAULT STATE
+;--- WBW
+;SD_OPRDEF	.EQU	%11111111	; OUTPUT PORT DEFAULT STATE
+SD_OPRDEF	.EQU	%11101111	; OUTPUT PORT DEFAULT STATE
+;---
 SD_INPREG	.EQU	SD_IOBASE	; INPUT REGISTER
 SD_CS0		.EQU	%00001000	; SELECT
 SD_CLK		.EQU	%00010000	; CLOCK
@@ -1801,6 +1805,7 @@ SD_SETUP:
 ;
 #IF (SDMODE == SDMODE_PIO)
 	LD	A,SD_OPRDEF		; All output bits high
+	LD	(SD_OPRVAL),A		; WBW
 	OUT	(SD_OPRREG),A
 	LD	A,$CF			; Port B mode 3
 	OUT	(SD_DDR),A
diff --git a/Source/ver.inc b/Source/ver.inc
index 14e91216..df4be77a 100644
--- a/Source/ver.inc
+++ b/Source/ver.inc
@@ -2,7 +2,7 @@
 #DEFINE	RMN	3
 #DEFINE	RUP	0
 #DEFINE	RTP	0
-#DEFINE BIOSVER	"3.3.0-dev.33"
+#DEFINE BIOSVER	"3.3.0-dev.35"
 #define rmj	RMJ
 #define rmn	RMN
 #define rup	RUP
diff --git a/Source/ver.lib b/Source/ver.lib
index 69b8f659..9e38fd51 100644
--- a/Source/ver.lib
+++ b/Source/ver.lib
@@ -3,5 +3,5 @@ rmn	equ	3
 rup	equ	0
 rtp	equ	0
 biosver	macro
-	db	"3.3.0-dev.33"
+	db	"3.3.0-dev.35"
 	endm