You should find the following ROM
images in the Output driectory.
Refer to the descriptions below to select 
one that matches your hardware 
configuration, burn it, and use it.

All builds have the following:
 - 512KB ROM Disk
 - 512KB RAM Disk
 - 38.4Kbps baud console

All of the above can be modified by using
a custom build.  See Build.txt in the 
Doc directory.

Note have all hard disk units are assumed to have
at least 2 slices and therefore two drive letters
are assigned per disk unit by default.  However,
you can easily add/remove drive letters and slices
by using the ASSIGN command to modify drive
letter to disk/slice mapping on the fly at
the command line.

Note that there are no longer separate
ROM images for CP/M and ZSystem.  Both
OS variants are now imbedded in the ROM
image and you are given the ability to
choose the one you want to boot at
startup.

  N8VEM_std.rom for N8VEM Z80 SBC V1/V2:
    - Drives A:=ROM, B:=RAM

  N8VEM_diskio.rom for N8VEM Z80 SBC V1/V2 + DISKIO:
    - Floppy support via DISKIO
    - IDE support via DISKIO
    - Drives A:=ROM, B:=RAM, C:=FD0, D:=FD1, E:=IDE0:00, F:=IDE0:01

  N8VEM_dide.rom for N8VEM Z80 SBC V1/V2 + DUAL IDE:
    - Floppy support via DISKIO
    - IDE support via DISKIO
    - Drives A:=ROM, B:=RAM, C:=FD0, D:=FD1, E:=IDE0:00, F:=IDE0:01
    
  N8VEM_diskio3.rom for N8VEM Z80 SBC V1/V2 + DISKIO3:
    - Floppy support via DISKIO3
    - IDE support via DISKIO3
    - Drives A:=ROM, B:=RAM, C:=FD0, D:=FD1, E:=IDE0:00, F:=IDE0:01

  N8VEM_diskio3+cvdu.rom for N8VEM Z80 SBC V1/V2 + DISKIO3:
    - Floppy support via DISKIO3
    - IDE support via DISKIO3
    - ColorVDU board support
    - Console defaults to VGA & PS/2 Keyboard.  Short JP2 (CONFIG)
      to use the serial port as the console.
    - Drives A:=ROM, B:=RAM, C:=FD0, D:=FD1, E:=IDE0:00, F:=IDE0:01

  N8VEM_ppide.rom for N8VEM Z80 SBC V1/V2 + PPIDE:
    - PPIDE support via built-in PPI
    - Drives A:=ROM, B:=RAM, C:=PPIDE0:00, D:=PPIDE0:01
    
  N8VEM_ppisd.rom for N8VEM Z80 SBC V1/V2 + PPISD:
    - PPISD support
    - Drives A:=ROM, B:=RAM, C:=SD0:00, D:=SD0:01
    
  N8VEM_dsd.rom for N8VEM Z80 SBC V1/V2 + Dual SD:
    - Dual SD support
    - Drives A:=ROM, B:=RAM, C:=SD0:00, D:=SD0:01
    
  N8VEM_propio.rom for N8VEM Z80 SBC V1/V2 + PROPIO:
    - SD Card support via PropIO
    - VGA console support via PropIO
    - PS/2 Keyboard support via PropIO
    - You *MUST* use the RomWBW specific firmware
      for the Propeller found in the Support directory!
    - Console defaults to VGA & PS/2 Keyboard.  Short JP2 (CONFIG)
      to use the serial port as the console.
    - Drives A:=ROM, B:=RAM, C:=PRPSD0:00, D:=PRPSD0:01

  N8VEM_mfp.rom for N8VEM Z80 SBC V1/V2:
    - IDE support via Multifunction / PIC
    - Second UART via Multifunction / PIC
    - Drives A:=ROM, B:=RAM, C:=PPIDE0:00, D:=PPIDE0:01

  N8VEM_ci.rom for N8VEM Z80 SBC V1/V2:
    - Cassette Interface mapped to RDR/PUN
    - Drives A:=ROM, B:=RAM

  N8VEM_simh.rom for N8VEM SIMH Simulator:
    - SIMH HDSK (simulated hard disk) support
    - Drives A:=ROM, B:=RAM, C:=HDSK0:00, D:=HDSK0:01

  N8VEM_rf.rom for N8VEM Z80 SBC V1/2 + RAM Flopppy:
    - RAM Floppy support
    - Drives A:=ROM, B:=RAM, C:=RF0, D:=RF1

  N8VEM_vdu.rom for N8VEM Z80 SBC V1/V2:
    - VDU board support
    - Drives A:=ROM, B:=RAM
	- NOTE: Console defaults to CRT & PS/2 Keyboard.  Short JP2
	  (one bit input port) to use the serial port as the console.
    
  N8VEM_cvdu.rom for N8VEM Z80 SBC V1/V2:
    - ColorVDU board support
    - Console defaults to VGA & PS/2 Keyboard.  Short JP2 (CONFIG)
      to use the serial port as the console.
    - Drives A:=ROM, B:=RAM
    
  ZETA_std.rom for Zeta Z80 SBC:
    - Floppy support via built-in FDC
    - Drives A:=ROM, B:=RAM, C:=FD0, D:=FD1, E:=PPIDE00-0, F:=PPIDE0:01

  ZETA_ppide.rom for Zeta Z80 SBC + PPIDE:
    - Floppy support via built-in FDC
    - PPIDE support via built-in PPI
    - Drives A:=ROM, B:=RAM, C:=PPIDE0:00, D:=PPIDE0:01
    
  ZETA_ppisd.rom for Zeta Z80 SBC + PPISD:
    - Floppy support via built-in FDC
    - PPISD support
    - Drives A:=ROM, B:=RAM, C:=SD0:00, D:=SD0:01
    
  ZETA_ppp.rom for Zeta Z80 SBC w/ ParPortProp:
    - Floppy support via built-in FDC
    - SD Card support via ParPortProp
    - VGA console support via ParPortProp
    - PS/2 Keyboard support via ParPortProp
    - You *MUST* use the RomWBW specific firmware
      for the Propeller found in the Support directory!
    - Console defaults to VGA & PS/2 Keyboard.  Short JP1 (CONFIG)
      to use the serial port as the console.
    - Drives A:=ROM, B:=RAM, C:=FD0, D:=FD1, E:=PPPSD0:00, F:=PPPSD0:01

  ZETA2_std.rom for Zeta 2 Z80 SBC:
    - Floppy support via built-in FDC
    - PPIDE support via built-in PPI
    - Drives A:=ROM, B:=RAM, C:=FD0, D:=FD1, E:=PPIDE00-0, F:=PPIDE0:01

  ZETA2_ppide.rom for Zeta 2 Z80 SBC + PPIDE:
    - Floppy support via built-in FDC
    - PPIDE support via built-in PPI
    - Drives A:=ROM, B:=RAM, C:=PPIDE0:00, D:=PPIDE0:01
    
  ZETA2_ppisd.rom for Zeta 2 Z80 SBC + PPISD:
    - Floppy support via built-in FDC
    - PPISD support
    - Drives A:=ROM, B:=RAM, C:=SD0:00, D:=SD0:01
    
  ZETA2_ppp.rom for Zeta 2 Z80 SBC w/ ParPortProp:
    - Floppy support via built-in FDC
    - SD Card support via ParPortProp
    - VGA console support via ParPortProp
    - PS/2 Keyboard support via ParPortProp
    - You *MUST* use the RomWBW specific firmware
      for the Propeller found in the Support directory!
    - Console defaults to VGA & PS/2 Keyboard.  Short JP1 (CONFIG)
      to use the serial port as the console.
    - Drives A:=ROM, B:=RAM, C:=FD0, D:=FD1, E:=PPPSD0:00, F:=PPPSD0:01

  N8_2511.rom for N8 2511 Z180:
    - Assumes CPU oscillator frequency of 18.432MHz
    - Floppy support via built-in FDC
    - SD card support via built-in SD card slot
    - Drives A:=ROM, B:=RAM, C:=FD0, D:=FD1, E:=SD0:00, F:=SD0:01

  N8_2312.rom for N8 2312 Z180:
    - Assumes CPU oscillator frequency of 18.432MHz
    - Floppy support via built-in FDC
    - SD card support via built-in SD card slot
    - Drives A:=ROM, B:=RAM, C:=FD0, D:=FD1, E:=SD0:00, F:=SD0:01

  MK4_std.rom for Mark IV Z180 SBC:
    - Assumes CPU oscillator frequency of 18.432MHz
    - Onboard SD Card
    - Onboard IDE
    - Drives A:=ROM, B:=RAM, C:=SD0-0, D:=SD0-1, E:=IDE0:00, F:=IDE0:01

  MK4_diskio3.rom for Mark IV Z180 SBC:
    - Assumes CPU oscillator frequency of 18.432MHz
    - Floppy support via DISKIO3
    - IDE support via DISKIO3
    - Drives A:=ROM, B:=RAM, C:=FD0, D:=FD1, E:=IDE0:00, F:=IDE0:01

  MK4_propio.rom for Mark IV Z180 SBC:
    - Assumes CPU oscillator frequency of 18.432MHz
    - SD Card support via PropIO
    - VGA console support via PropIO
    - PS/2 Keyboard support via PropIO
    - You *MUST* use the RomWBW specific firmware
      for the Propeller found in the Support directory!
    - Drives A:=ROM, B:=RAM, C:=PRPSD0:00, D:=PRPSD0:01

  UNA_std.rom for all UNA supported platforms (SBC V1/2, Zeta, Mark IV)
    - Initial baud rate is 9600, but can be configured
    - Resources are managed dynamically by UNA BIOS
    - Refer to UNA project for more details
    - Drive assignments occur dynamically based on UNA config