RomWBW/Source/Images/d_z80asm/u0/SYNTAX.HLP

   Here is a very brief introduction to the syntax and use of the assembler
and linker.  The default operation of each tool can be changed using the
corresponding configuration program, CONFIG for Z80ASM, 180FIG for SLR180,
and LNKFIG for SLRNK.  Make copies of the master disk and then experiment
with the configuration programs.  They are self-prompting and easy to use.

   The basic syntax for the assemblers is: Z80ASM FILE/options or SLR180
FILE/options.  The file name must have a type of Z80 (unless changed by
CONFIG) for Z80ASM or type 180 (unless changed by 180FIG) for SLR180.  The
most commonly used options are:

	A	Generate, in one pass, an absolute output (COM file). This
		is the preferred mode unless the source is not self-
		contained and requires linkage to other modules.

	H	Generate a HEX output file.  This is rarely needed (only for
		patch files); normally the 'A' option is preferrable.

	M	Generate a Microsoft relocatable format.  Use '/M6' or just
		'/6' for six significant characters (this is what the
		Conn libraries use) or '/M7' or just '/7' for seven
		significant characters.

	R	Generate an SLR-format relocatable file

	F	Perform a two-pass assembly (slower, but all symbol values
		resolved in the listing) and generate a listing file.  Use
		this option only when a listing is needed.

	L	Generate a one-pass assembly and listing.  Forward-
		referenced symbols will not have their values included in
		the listing.

	S	Generate a symbol file (this is in a special format that
		must be converted using MAKESYM.COM to make a symbol file
		that can be used by symbolic debuggers such as SID and DSD.

	X	Generate a crossreference listing.

	U	Declare all undefined symbols to be external.

   To assemble ZCPR33 to a COM file for installation using a disk utility or
debugging program, I use the command line "Z80ASM ZCPR33/A".  Actually, I do
not have to enter the 'A' because I configure my Z80ASM to default to
absolute output mode.

   Drives can be specified for the source, code output, and listing outputs
in the same way as with the Digital Research ASM.COM assembler, namely,
using three file-type letters.  Thus

	SLR180 PROG.ABC/HF

will read PROG.180 from drive A, send PROG.HEX (the 'H' option specifies HEX
output) to drive B, and send the two-pass listing file PROG.LST to drive C. 
Valid drive letters are 'A' to 'P' and '@', the latter indicating the
currently logged drive.  If you want to suppress one of the outputs, use the
letter 'Z' in positions two or three.  The third letter specifies the
destination for listing, crossreference, and symbol table outputs.  The
letter 'X' in the third position will send this output to the console, and
the letter 'Y' will send it to the printer.  For example, the command

	SLR180 PROG.@@Z/AF

will force a two-pass assembly but will not produce a listing file.


   The linker is more complex (as linkers always are).  Here is a sample
command line for linking a typical ZCPR3 utility program called PROG.  Let's
assume that we have assembled it to a 6-character standard Microsoft REL
file using the command line

	Z80ASM PROG/6	or    SLR180 PROG/6

Then we link it with the Conn libraries as follows:

	SLRNK PROG/N,/A:100,PROG,VLIB/S,Z3LIB/S,SYSLIB/S,/E

The first item (PROG/N) declares the 'N'ame of the output COM file.  The
second item sets the linkage addresses for 'A'll segments (code, data,
common) to begin at 100H.  If you are using separate data segments, you
could use an expression like "/P:100,/D:2000" to set the code ('P'rogram
segment to 100H and the 'D'ata segment to 2000H.  The 'A' directive takes
care of things automatically, though it follows the M80 convention (I
believe) of putting DSEGs before CSEGs from each module.  This messes up the
ZCPR3 environment header at the beginning of the program.  If you do declare
separate DSEGs, you should do one linkage using a high value for the DSEG
address.  Note the reported address of the end of the CSEG and relink using
the next address in the '/D' directive.

   The third item on the command line links in the main module, PROG.REL. 
The next three items link in the library modules, where the '/S' option
causes the libraries to be 'S'canned so that only the modules required by
PROG will be linked in.  Without the 'S' switch, the entire libraries would
be linked in, making for a huge output file.  The final item is the 'E'nd
switch, telling the linker that we are done and that the output file should
be written to disk.

   The switch '/V' will put the linker in verbose mode, and it will display
much more information about what it is doing on the screen.  Including an
item of the form 'NAME/M' will result in a load map being written to a disk
file of the name NAME.SYM.

   Two words of caution are in order.  The slash options are generally
processed before the files are processed.  Thus the command

	SLRNK OUTNAME/N/A:100,PROGNAME/E

will not work because the '/E' directive to 'End' the linkage will be
processed before PROGNAME.REL has been read in.  However, the following
command will work:

	SLRNK /A:100,PROGNAME,OUTNAME/N/M

My recommendation is to put the directives in their own individual tokens
and to declare output file names first, addresses second, and input file
names third.  SLRNK will tolerate some deviations from this, but the more
advanced SLRNK+ virtual linker is fussier when it is generating SPR or PRL
type files.  Thus I would recommend:

	SLRNK OUTNAME/N,MAPNAME/M,/V,/A:100,INPUT,/E

The second caution regards mixing SLR and Microsoft format REL files.  The
linker will handle mixtures, but incompatibilites in the files can easily
occur.  If the source code has labels of more than 6 characters, the
Microsoft REL file will have truncated them to 6 characters, but the SLR REL
format will include the first 16!  Conn's SYSLIB, Z3LIB, and Z3LIB libraries
were linked to 6 characters although the official names of a number of the
routines are longer than 6 characters.  I recommend picking up my SLR
versions of the libraries and working entirely with SLR format REL files. 
They are shorter and faster and will support meaningfully long names.


     With the linker and the assembler, the individual items can be entered
one item at a time in interactive mode.  The assembler, for example, can
assemble multiple programs.  Just enter Z80ASM or SLR180 alone on the
command line and then respond to the prompts.

	B0:WORK>Z80ASM		; invoke assembler
	%PROG1/A		; absolute assembly of PROG1
	%PROG2/R		; SLR-format REL assembly of PROG2
	%/Q			; quit assembling (control-c works too)
	B0:WORK>		; back to system

This is very efficient, since the assembler only has to load once, and the
SLR assemblers are so fast that this time is often a large fraction of the
total time required for the assembly.

   The linker will handle only one linkage at a time, but the items can be
entered interactively.

	B0:WORK>SLRNK PROG1/N	; invoke linker (some items on command line)
	%/A:100,PROG1		; more items at each prompt
	%/V			; change to verbose mode
	%VLIB/S			; link in VLIB
	%/U			; list undefined symbols at this point
	%Z3LIB/S,SYSLIB/S,/U	; link in rest of libraries
	%/E			; end linkage
	B0:WORK>		; back to system

   Whole scripts of commands can be passed to the assemblers and linker in
special files.  Thus the following commands

	SLR180 ASCRIPT/I
	SLRNK LSCRIPT/I

will read in text files with the names ASCRIPT.SUB and LSCRIPT.SUB (the file
type SUB can be reconfigured -- I prefer to use SLR so as not to confuse the
files with SUBMIT files).  This is very handy for performing very lengthy
sequences of operations, such as assembling all 200 programs that go into
SYSLIB!  Let me tell you, it is amazing to watch SLR180 gobble them up!

					Jay Sage