Changed the Attribute for MD RF devices reordering/fliping (RF<->Flash) so bit masks are easier

Source/Apps/assign/assign.asm

@@ -614,17 +614,11 @@ bootdra:
 ; Note: if MDFFENABLE is enabled, this wont select the ROM since the
 ; driver returns MD_AFSH (%00010111), and we cannot generalise this mask
 bootdro:
-	ld	a,$FF		; specific mask to include all BITS
+	ld	a,%11111101	; ROM mask, excluding Bit 1, which varies
 	ld	(atrmask),a	; mask for device attributes
-	ld	a,%00010100	; specific mask for ROM drive. "MD_AROM"
+	ld	a,%00010100	; for values "MD_AROM", "MD_AFSH"; Att="000101x0"
 	ld	(atrcomp),a	; compare to after mask
 	call	bootadds	; do single slice assignment
-; possible workaround below, not elegant. other woraround is to have a specific option for this code
-; Better option is change the definitions for device attribute media types to
-; 4=ROM, 5=RAM, 6=FLASH, 7=RAMF, (6,7 swapped) so much easir to mask RAM/ROM as only 1 bit difference
-;	ld	a,%00010111	; specific mask for ROM drive. "MD_AFSH"
-;	ld	(atrcomp),a	; compare to after mask
-;	call	bootadds	; do single slice assignment
 	ret			; Finished, returning error
 ;
 ; FLOPPY DRIVE(S)

Source/CBIOS/cbios.asm

@@ -2343,10 +2343,8 @@ INIT2:
 	LD	C,(HL)		; PUT UNIT NUM IN C
 	RST	08		; CALL HBIOS
 	LD	A,C		; GET ATTRIBUTES
-	AND	%10001111	; ISOLATE TYPE BITS
-	CP	%00000100	; NOT FLOPPY, TYPE = ROM?
-	JR	Z,INIT2A	; IF SO, ADJUST DEF DRIVE
-	CP	%00000111	; NOT FLOPPY, TYPE = FLASH?
+	AND	%10001101	; ISOLATE TYPE BITS, NOT FLOPPY
+	CP	%00000100	; TYPE=ROM/FLASH ; Att="0xxx01x0"
 	JR	NZ,INIT2X	; IF NOT THEN DONE
 ;
 INIT2A:

Source/Doc/SystemGuide.md

@@ -1162,7 +1162,7 @@ The non-Floppy specific bits are:
 |---------:|--------------------------------------------------|
 | 4        | LBA Capable                                      |
 | 3-0      | Media Type: 0=Hard Disk, 1=CF, 2=SD, 3=USB,      |
-|          |   4=ROM, 5=RAM, 6=RAMF, 7=FLASH, 8=CD-ROM,       |
+|          |   4=ROM, 5=RAM, 6=FLASH, 7=RAMF, 8=CD-ROM,       |
 |          |   9=Cartridge                                    |
 
 Device Type (D) indicates the specific hardware driver that handles the 

Source/HBIOS/hbios.asm

@@ -8701,8 +8701,8 @@ PS_DTSD		.TEXT	"SD Card$"
 PS_DTUSB	.TEXT	"USB Drive$"
 PS_DTROM	.TEXT	"ROM Disk$"
 PS_DTRAM	.TEXT	"RAM Disk$"
+PS_DTFSH	.TEXT	"Flash ROM"
 PS_DTRF		.TEXT	"RAM Floppy$"
-PS_DTFSH	.TEXT	"Flash Drive$"
 PS_DTCD		.TEXT	"CD-ROM$"
 PS_DTCRT	.TEXT	"Cartridge$"
 PS_DTOTHER	.TEXT	"???$"

Source/HBIOS/md.asm

@@ -23,7 +23,7 @@ MD_ATTRIB	.EQU	7		; OFFSET OF ATTRIBUTE (BYTE)
 ;
 MD_AROM		.EQU	%00010100	; ROM ATTRIBUTE
 MD_ARAM		.EQU	%00010101	; RAM ATTRIBUTE
-MD_AFSH		.EQU	%00010111	; FLASH ATTRIBUTE
+MD_AFSH		.EQU	%00010110	; FLASH ATTRIBUTE
 ;
 MD_FDBG		.EQU	0		; FLASH DEBUG CODE
 MD_FVBS		.EQU	1		; FLASH VERBOSE OUTPUT

Source/HBIOS/rf.asm

@@ -198,7 +198,7 @@ RF_GEOM:
 RF_DEVICE:
 	LD	D,DIODEV_RF		; D := DEVICE TYPE
 	LD	E,(IY+RF_DEV)		; E := PHYSICAL DEVICE NUMBER
-	LD	C,%00010110		; C := ATTRIBUTES, NON-REMOVABLE RAM FLOPPY
+	LD	C,%00010111		; C := ATTRIBUTES, NON-REMOVABLE RAM FLOPPY
 	LD	H,0			; H := 0, DRIVER HAS NO MODES
 	LD	L,(IY+RF_IOAD)		; L := BASE I/O ADDRESS
 	XOR	A			; SIGNAL SUCCESS