Regen Doc

- Added WDATE command courtesy Kevin Boone.  See https://github.com/kevinboone/wdate-cpm for more information.
- Final cleanup of PPA/IMM/SYQ drivers including CPU speed compensated timeouts.

Doc/ChangeLog.txt

@@ -5,6 +5,11 @@ Version 3.3
 - A?C: Support for SD PIO
 - A?C: Support for Z80-Retro SD interface
 - WBW: Support per-drive floppy configuration
+- WBW: Support for Bill Shen's VGARC
+- WBW: Support for MG014 Parallel Port module + printer
+- WBW: Support for EMM Zip Drive on PPI interface (much inspiration from Alan Cox)
+- WBW: Support for PPA Zip Drive on PPI interface (much inspiration from Alan Cox)
+- WBW: Support for SyQuest SparQ Drive on PPI interface (much inspiration from Alan Cox)
 
 Version 3.2.1
 -------------

ReadMe.md

@@ -3,7 +3,7 @@
 **RomWBW ReadMe** \
 Version 3.3 \
 Wayne Warthen  ([wwarthen@gmail.com](mailto:wwarthen@gmail.com)) \
-03 May 2023
+06 Jun 2023
 
 # Overview
 

ReadMe.txt

@@ -1,6 +1,6 @@
 RomWBW ReadMe
 Wayne Warthen (wwarthen@gmail.com)
-03 May 2023
+06 Jun 2023
 
 
 

Source/Apps/assign.asm

@@ -1918,9 +1918,9 @@ dev06	.db	"SD",0
 dev07	.db	"PRPSD",0
 dev08	.db	"PPPSD",0
 dev09	.db	"HDSK",0
-dev10	.equ	devunk
-dev11	.equ	devunk
-dev12	.equ	devunk
+dev10	.db	"PPA",0
+dev11	.db	"IMM",0
+dev12	.db	"SYQ",0
 dev13	.equ	devunk
 dev14	.equ	devunk
 dev15	.equ	devunk

Source/CBIOS/cbios.asm

@@ -2929,6 +2929,14 @@ DRV_INIT3:
 	RET
 ;
 DRV_INIT3A:
+	; CHECK FOR HARD DISK REMOVABLE CARTRIDGE DRIVES
+	CP	DIODEV_PPA		; PPA (ZIP DRIVE) IS REMOVABLE
+	JR	Z,DRV_INIT3B		; IF SO, SKIP MEDIA CHECK
+	CP	DIODEV_IMM		; IMM (ZIP DRIVE) IS REMOVABLE
+	JR	Z,DRV_INIT3B		; IF SO, SKIP MEDIA CHECK
+	CP	DIODEV_SYQ		; IMM (ZIP DRIVE) IS REMOVABLE
+	JR	Z,DRV_INIT3B		; IF SO, SKIP MEDIA CHECK
+
 	; CHECK FOR ACTIVE AND RETURN IF NOT
 	PUSH	DE			; SAVE DE (HARD DISK VOLUME COUNTER)
 	PUSH	HL			; SAVE DRIVE LIST PTR
@@ -2944,6 +2952,7 @@ DRV_INIT3A:
 
 	RET	NZ			; IF NO MEDIA, JUST RETURN
 
+DRV_INIT3B:
 	; IF ACTIVE...
 	LD	(HL),C			; SAVE UNIT NUM IN LIST
 	INC	HL			; BUMP PTR
@@ -3392,9 +3401,9 @@ DEV06	.DB	"SD$"
 DEV07	.DB	"PRPSD$"
 DEV08	.DB	"PPPSD$"
 DEV09	.DB	"HDSK$"
-DEV10	.EQU	DEVUNK
-DEV11	.EQU	DEVUNK
-DEV12	.EQU	DEVUNK
+DEV10	.DB	"PPA$"
+DEV11	.DB	"IMM$"
+DEV12	.DB	"SYQ$"
 DEV13	.EQU	DEVUNK
 DEV14	.EQU	DEVUNK
 DEV15	.EQU	DEVUNK

Source/CPM3/boot.z80

@@ -181,6 +181,14 @@ dinit3:
 	ret
 ;
 dinit3a:
+	; check for hard disk removable cartridge drives
+	cp	0A0h			; ppa (zip drive) is removable
+	jr	z,dinit3b		; if so, skip media check
+	cp	0B0h			; imm (zip drive) is removable
+	jr	z,dinit3b		; if so, skip media check
+	cp	0C0h			; syq (syquest drive) is removable
+	jr	z,dinit3b		; if so, skip media check
+
 	; check for active and return if not
 	push	de			; save de (hard disk volume counter)
 	push	hl			; save drive list ptr
@@ -195,7 +203,8 @@ dinit3a:
 	pop	de			; restore de
 	
 	ret	nz			; if no media, just return
-	
+
+dinit3b:
 	; if active...
 	ld	(hl),c			; save unit num in list
 	inc	hl			; bump ptr

Source/Doc/Applications.md

@@ -51,6 +51,7 @@ found:
 | INTTEST     | No       | Yes        | Yes      |
 | FAT         | No       | Yes        | Yes      |
 | TUNE        | No       | Yes        | Yes      |
+| WDATE       | No       | Yes        | Yes      |
 
 `\clearpage`{=latex}
 
@@ -889,6 +890,28 @@ written in C and requires SDCC to compile. As such it is not part of
 the RomWBW build process. However, the full project and source code is
 found in the [FAT GitHub Repository](https://github.com/wwarthen/FAT).
 
+## Known Issues
+
+CP/M (and workalike) OSes have significant restrictions on filename
+characters.  The FAT application will block any attempt to create a
+file on the CP/M filesystem containing any of these prohibited
+characters:
+
+|         `< > . , ; : = ? * [ ] _ % | ( ) / \`
+
+The operation will be aborted with "`Error: Invalid Path Name`" if such
+a filename character is encountered.
+
+Since MS-DOS does allow some of these characters, you can have
+issues when copying files from MS-DOS to CP/M if the MS-DOS filenames
+use these characters.  Unfortunately, FAT is not yet smart enough to
+substitute illegal characters with legal ones.  So, you will need to
+clean the filenames before trying to copy them to CP/M.
+
+The FAT application does try to detect the scenario where you are
+copying a file to itself.  However, this detection is not perfect and
+can corrupt a file if it occurs.  Be careful to avoid this.
+
 `\clearpage`{=latex}
 
 # TUNE
@@ -1106,3 +1129,85 @@ can be used to reduce your processor speed.
 
 VGMPLAY is still under development. The source code is provided in the 
 RomWBW distribution.
+
+`\clearpage`{=latex}
+
+# WDATE
+
+`wdate` is a utility for CP/M systems that have Wayne Warthen's
+ROMWBW firmware. It reads or sets the real-time clock, using function
+calls in the BIOS. It should work on any RTC device that is supported by
+ROMWBW, including the internal interrupt-driven timer that is is available
+on some systems. 
+
+`wdate` differs from the `rtc.com` utility that is provided with the
+ROMWBW version of CP/M in that it only gets and sets the date/time. 
+`rtc.com` can also manipulate the nonvolatile RAM in certain clock
+devices, and modify the charge controller. However, `wdate` is (I would
+argue) easier to use, as it takes its input from the command line, which
+can be edited, and it's less fussy about the format. It doesn't require
+the date to be set if you only want to change the time, for example.
+ In addition, `wdate` has at least some error checking.
+
+`wdate` displays the day-of-week and month as English text, not 
+numbers. It calculates the day-of-week from the year, month, and day.
+RTC chips usually store a day-of-week value, but it's useless in this
+application for two reasons: first, the BIOS does not expose it. Second,
+there is no universally-accepted way to interpret it (which day does
+the week start on? Is '0' a valid day of the week?)
+
+## Syntax
+
+| `WDATE`
+| `WDATE ` *`<hr> <min>`*
+| `WDATE ` *`<hr> <min> <sec>`*
+| `WDATE ` *`<year> <month> <day> <hr> <min> <sec>`*
+
+## Usage
+
+    A> wdate
+    Saturday 27 May 13:14:39 2023
+
+With no arguments, displays the current date and time. 
+
+    A> wdate hr min
+
+With two arguments, sets the time in hours and minutes, without changing date
+or seconds
+
+    A> wdate hr min sec
+
+With three arguments, sets the time in hours, minutes, and seconds, without
+changing date
+
+    A> wdate year month day hr min sec
+
+With six arguments, sets date and time. All numbers are one or two digits.  The
+two-digit year starts at 2000. 
+
+    A> wdate /?
+
+Show a summary of the command-line usage.
+
+## Notes
+
+I've tested this utility with the DS1302 clock board designed by Ed 
+Brindly, and on the interrupt-driven timer built into my Z180 board. 
+However, it does not interact with hardware, only BIOS; I would expect 
+it to work with other hardware.
+
+wdate checks for the non-existence of ROMWBW, and also for failing 
+operations on the RTC. It will display the terse "No RTC" message in 
+both cases.
+
+The ROMWBW functions that manipulate the date and time operate on BCD 
+numbers, as RTC chips themselves usually do. wdate works in decimal, so 
+that it can check that the user input makes sense. A substantial part of
+the program's code is taken up by number format conversion and range 
+checking.
+
+## Etymology
+
+The `WDATE` application was written and contributed by Kevin Boone.
+The source code is available on GitHub at
+[https://github.com/kevinboone/wdate-cpm/blob/main/README.md](https://github.com/kevinboone/wdate-cpm/blob/main/README.md).

Source/Doc/UserGuide.md

@@ -3808,6 +3808,7 @@ the RomWBW HBIOS configuration.
    - WDC Floppy Disk Controller w/ 3.5" HD Drives
    - Onboard IDE Hard Disk Interface Module
    - PPIDE Hard Disk Interface Module
+   - VGARC Video & Keyboard Module
  - Serial baud rate is usually determined by hardware for ACIA and
    SIO interfaces
 
@@ -3831,6 +3832,7 @@ the RomWBW HBIOS configuration.
    - WDC Floppy Disk Controller w/ 3.5" HD Drives
    - Onboard IDE Hard Disk Interface Module
    - PPIDE Hard Disk Interface Module
+   - VGARC Video & Keyboard Module
  - Serial baud rate is usually determined by hardware for ACIA and
    SIO interfaces
 
@@ -3854,6 +3856,7 @@ the RomWBW HBIOS configuration.
    - WDC Floppy Disk Controller w/ 3.5" HD Drives
    - Onboard IDE Hard Disk Interface Module
    - PPIDE Hard Disk Interface Module
+   - VGARC Video & Keyboard Module
  - Serial baud rate is usually determined by hardware for ACIA and
    SIO interfaces
 
@@ -3893,10 +3896,12 @@ may be discovered by RomWBW in your system.
 | DSKY      | System   | Keypad & Display                                       |
 | DSRTC     | RTC      | Maxim DS1302 Real-Time Clock w/ NVRAM                  |
 | DUART     | Char     | SCC2681 or compatible Dual UART                        |
-| FD        | Disk     | 8272 of compatible Floppy Disk Controller              |
+| EMM       | Disk     | Disk drive on Parallel Port emm interface (Zip Drive)  |
+| FD        | Disk     | 8272 or compatible Floppy Disk Controller              |
 | GDC       | Video    | uPD7220 Video Display Controller                       |
 | HDSK      | Disk     | SIMH Simulator Hard Disk                               |
 | IDE       | Disk     | IDE/ATA Hard Disk Interface                            |
+| IMM       | Disk     | IMM Zip Drive on PPI                                   |
 | INTRTC    | RTC      | Interrupt-based Real Time Clock                        |
 | KBD       | Kbd      | 8242 PS/2 Keyboard Controller                          |
 | KIO       | System   | Zilog Serial/ Parallel Counter/Timer                   |
@@ -3906,6 +3911,7 @@ may be discovered by RomWBW in your system.
 | I2C       | System   | I2C Interface                                          |
 | PIO       | Char     | Zilog Parallel Interface Controller                    |
 | PPIDE     | Disk     | 8255 IDE/ATA Hard Disk Interface                       |
+| PPA       | Disk     | PPA Zip Drive on PPI                                   |
 | PPK       | Kbd      | Matrix Keyboard                                        |
 | PPPSD     | Disk     | ParPortProp SD Card Interface                          |
 | PPPCON    | Serial   | ParPortProp Serial Console Interface                   |
@@ -3918,11 +3924,12 @@ may be discovered by RomWBW in your system.
 | SIO       | Char     | Zilog Serial Port Interface                            |
 | SN76489   | Sound    | SN76489 Programmable Sound Generator                   |
 | SPK       | Sound    | Bit-bang Speaker                                       |
+| SYQ       | Disk     | Iomega SparQ Drive on PPI                              |
 | TMS       | Video    | TMS9918/38/58 Video Display Controller                 |
 | UART      | Char     | 16C550 Family Serial Interface                         |
 | USB-FIFO  | Char     | FT232H-based ECB USB FIFO                              |
 | VDU       | Video    | MC6845 Family Video Display Controller                 |
 | VGA       | Video    | HD6445CP4-based Video Display Controller               |
-| VRC       | Video    | VGARC Video Display Controller                        s |
+| VRC       | Video    | VGARC Video Display Controller                         |
 | YM        | Audio    | YM2612 Programmable Sound Generator                    |
 | Z2U       | Char     | Zilog Z280 CPU Built-in Serial Ports                   |

Source/Fonts/Build.cmd

@@ -11,8 +11,8 @@ echo Preparing compressed font files...
 lzsa -f2 -r font8x8u.bin font8x8c.bin || exit /b
 lzsa -f2 -r font8x11u.bin font8x11c.bin || exit /b
 lzsa -f2 -r font8x16u.bin font8x16c.bin || exit /b
-
 lzsa -f2 -r fontcgau.bin fontcgac.bin || exit /b
+lzsa -f2 -r fontvgarcu.bin fontvgarcc.bin || exit /b
 
 fonttool font8x8u.bin > font8x8u.asm || exit /b
 fonttool font8x11u.bin > font8x11u.asm || exit /b
@@ -20,6 +20,7 @@ fonttool font8x16u.bin > font8x16u.asm || exit /b
 fonttool font8x8c.bin > font8x8c.asm || exit /b
 fonttool font8x11c.bin > font8x11c.asm || exit /b
 fonttool font8x16c.bin > font8x16c.asm || exit /b
-
 fonttool fontcgau.bin > fontcgau.asm || exit /b
 fonttool fontcgac.bin > fontcgac.asm || exit /b
+fonttool fontvgarcu.bin > fontvgarcu.asm || exit /b
+fonttool fontvgarcc.bin > fontvgarcc.asm || exit /b

Source/Fonts/Makefile

@@ -1,8 +1,8 @@
 OBJECTS = \
-	font8x8u.asm font8x11u.asm font8x16u.asm fontcgau.asm \
-	font8x8c.asm font8x11c.asm font8x16c.asm fontcgac.asm
+	font8x8u.asm font8x11u.asm font8x16u.asm fontcgau.asm fontvgarcu.asm \
+	font8x8c.asm font8x11c.asm font8x16c.asm fontcgac.asm fontvgarcc.asm
 
-OTHERS = font8x8c.bin font8x11c.bin font8x16c.bin fontcgac.bin
+OTHERS = font8x8c.bin font8x11c.bin font8x16c.bin fontcgac.bin fontvgarcc.bin
 
 TOOLS = ../../Tools
 
@@ -26,5 +26,8 @@ font8x16c.bin: font8x16u.bin
 fontcgac.bin: fontcgau.bin
 	$(BINDIR)/lzsa -f2 -r $< $@
 
+fontvgarcc.bin: fontvgarcu.bin
+	$(BINDIR)/lzsa -f2 -r $< $@
+
 %.asm: %.bin
 	$(BINDIR)/bin2asm $< > $@

Source/HBIOS/Config/MBC_std.asm

@@ -48,6 +48,8 @@ DSKYMODE	.SET	DSKYMODE_NG	; DSKY VERSION: DSKYMODE_[V1|NG]
 UARTINTS	.SET	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 ;UARTCFG	.SET	UARTCFG | SER_RTS
 ;
+LPTENABLE	.SET	TRUE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
+;
 CVDUMON		.SET	CVDUMON_CGA	; CVDU: CVDU MONITOR SETUP: CVDUMON_[NONE|CGA|EGA]
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)

Source/HBIOS/Config/RCZ80_easy.asm

@@ -75,5 +75,6 @@ IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
 SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
+IMMENABLE	.SET	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
 ;
 PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)

Source/HBIOS/Config/RCZ80_kio.asm

@@ -72,5 +72,6 @@ IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
 SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
+IMMENABLE	.SET	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
 ;
 PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)

Source/HBIOS/Config/RCZ80_skz.asm

@@ -67,5 +67,6 @@ IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
 SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
+IMMENABLE	.SET	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
 ;
 PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)

Source/HBIOS/Config/RCZ80_std.asm

@@ -40,6 +40,8 @@ ACIAENABLE	.SET	TRUE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
 SIOENABLE	.SET	TRUE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
 DUARTENABLE	.SET	FALSE		; DUART: ENABLE 2681/2692 SERIAL DRIVER (DUART.ASM)
 ;
+LPTENABLE	.SET	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
+;
 TMSENABLE	.SET	FALSE		; TMS: ENABLE TMS9918 VIDEO/KBD DRIVER (TMS.ASM)
 TMSTIMENABLE	.SET	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 TMSMODE		.SET	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MSXKBD|COLECO]
@@ -59,5 +61,6 @@ PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
 SDMODE		.SET	SDMODE_PIO	; SD: DRIVER MODE: SDMODE_[JUHA|N8|CSIO|PPI|UART|DSD|MK4|SC|MT|PIO|USR]
 SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
+IMMENABLE	.SET	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
 ;
 PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)

Source/HBIOS/Config/RCZ80_tiny.asm

@@ -82,5 +82,6 @@ IDE0BASE	.SET	$90		; IDE 0: IO BASE ADDRESS
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
 SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
+IMMENABLE	.SET	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
 ;
 PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)

Source/HBIOS/Config/RCZ80_zrc.asm

@@ -59,5 +59,6 @@ IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
 SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
+IMMENABLE	.SET	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
 ;
 PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)

Source/HBIOS/Config/RCZ80_zrc_ram.asm

@@ -63,5 +63,6 @@ IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
 SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
+IMMENABLE	.SET	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
 ;
 PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)

Source/HBIOS/Makefile

@@ -24,7 +24,8 @@ endif
 
 include $(TOOLS)/Makefile.inc
 
-FONTS := font8x11c.asm font8x11u.asm font8x16c.asm font8x16u.asm font8x8c.asm font8x8u.asm fontcgac.asm fontcgau.asm
+FONTS := font8x11c.asm font8x11u.asm font8x16c.asm font8x16u.asm font8x8c.asm font8x8u.asm \
+	fontcgac.asm fontcgau.asm fontvgarcc.asm fontvgarcu.asm
 
 ifeq ($(CPUFAM),2)
 	TASM=$(BINDIR)/uz80as -t hd64180

Source/HBIOS/cfg_dyno.asm

@@ -252,6 +252,12 @@ PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)
 PIO_SBC		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR 8255 CHIP

Source/HBIOS/cfg_master.asm

@@ -311,10 +311,33 @@ PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
 PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
+LPTMODE		.EQU	LPTMODE_NONE	; LPT: DRIVER MODE: LPTMODE_[NONE|SPP|MG014]
 LPTCNT		.EQU	1		; LPT: NUMBER OF CHIPS TO DETECT (1-2)
+LPTTRACE	.EQU	1		; LPT: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 LPT0BASE	.EQU	$E8		; LPT 0: REGISTERS BASE ADR
 LPT1BASE	.EQU	$EC		; LPT 1: REGISTERS BASE ADR
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+PPACNT		.EQU	1		; PPA: NUMBER OF PPA DEVICES (1-2)
+PPATRACE	.EQU	1		; PPA: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+PPAMODE		.EQU	PPAMODE_SPP	; PPA: DRIVER MODE: PPAMODE_[NONE|SPP|MG014]
+PPA0BASE	.EQU	LPT0BASE	; PPA 0: BASE I/O ADDRESS OF PPI FOR PPA
+PPA1BASE	.EQU	LPT1BASE	; PPA 1: BASE I/O ADDRESS OF PPI FOR PPA
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+IMMCNT		.EQU	1		; IMM: NUMBER OF IMM DEVICES (1-2)
+IMMTRACE	.EQU	1		; IMM: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+IMMMODE		.EQU	IMMMODE_SPP	; IMM: DRIVER MODE: IMMMODE_[NONE|SPP|MG014]
+IMM0BASE	.EQU	LPT0BASE	; IMM 0: BASE I/O ADDRESS OF PPI FOR IMM
+IMM1BASE	.EQU	LPT1BASE	; IMM 1: BASE I/O ADDRESS OF PPI FOR IMM
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+SYQCNT		.EQU	1		; SYQ: NUMBER OF SYQ DEVICES (1-2)
+SYQTRACE	.EQU	1		; SYQ: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+SYQMODE		.EQU	IMMMODE_SPP	; SYQ: DRIVER MODE: SYQMODE_[NONE|SPP|MG014]
+SYQ0BASE	.EQU	LPT0BASE	; SYQ 0: BASE I/O ADDRESS OF PPI FOR SYQ
+SYQ1BASE	.EQU	LPT1BASE	; SYQ 1: BASE I/O ADDRESS OF PPI FOR SYQ
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO4BASE	.EQU	$90		; PIO: PIO REGISTERS BASE ADR FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)

Source/HBIOS/cfg_mbc.asm

@@ -234,11 +234,34 @@ PIOCNT		.EQU	2		; PIO: NUMBER OF CHIPS TO DETECT (1-2), 2 CHANNELS PER CHIP
 PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
 PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
-LPTENABLE	.EQU	TRUE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
+LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
+LPTMODE		.EQU	LPTMODE_SPP	; LPT: DRIVER MODE: LPTMODE_[NONE|SPP|MG014]
 LPTCNT		.EQU	1		; LPT: NUMBER OF CHIPS TO DETECT (1-2)
+LPTTRACE	.EQU	1		; LPT: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 LPT0BASE	.EQU	$E8		; LPT 0: REGISTERS BASE ADR
 LPT1BASE	.EQU	$EC		; LPT 1: REGISTERS BASE ADR
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+PPACNT		.EQU	1		; PPA: NUMBER OF PPA DEVICES (1-2)
+PPATRACE	.EQU	1		; PPA: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+PPAMODE		.EQU	PPAMODE_SPP	; PPA: DRIVER MODE: PPAMODE_[NONE|MG014]
+PPA0BASE	.EQU	LPT0BASE	; PPA 0: BASE I/O ADDRESS OF PPI FOR PPA
+PPA1BASE	.EQU	LPT1BASE	; PPA 1: BASE I/O ADDRESS OF PPI FOR PPA
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+IMMCNT		.EQU	1		; IMM: NUMBER OF IMM DEVICES (1-2)
+IMMTRACE	.EQU	1		; IMM: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+IMMMODE		.EQU	IMMMODE_SPP	; IMM: DRIVER MODE: IMMMODE_[NONE|SPP|MG014]
+IMM0BASE	.EQU	LPT0BASE	; IMM 0: BASE I/O ADDRESS OF PPI FOR IMM
+IMM1BASE	.EQU	LPT1BASE	; IMM 1: BASE I/O ADDRESS OF PPI FOR IMM
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+SYQCNT		.EQU	1		; SYQ: NUMBER OF SYQ DEVICES (1-2)
+SYQTRACE	.EQU	1		; SYQ: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+SYQMODE		.EQU	IMMMODE_SPP	; SYQ: DRIVER MODE: SYQMODE_[NONE|SPP|MG014]
+SYQ0BASE	.EQU	LPT0BASE	; SYQ 0: BASE I/O ADDRESS OF PPI FOR SYQ
+SYQ1BASE	.EQU	LPT1BASE	; SYQ 1: BASE I/O ADDRESS OF PPI FOR SYQ
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO4BASE	.EQU	$90		; PIO: PIO REGISTERS BASE ADR FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)

Source/HBIOS/cfg_mk4.asm

@@ -248,10 +248,18 @@ PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
 PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
+LPTMODE		.EQU	LPTMODE_NONE	; LPT: DRIVER MODE: LPTMODE_[NONE|SPP|MG014]
 LPTCNT		.EQU	1		; LPT: NUMBER OF CHIPS TO DETECT (1-2)
+LPTTRACE	.EQU	1		; LPT: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 LPT0BASE	.EQU	$E8		; LPT 0: REGISTERS BASE ADR
 LPT1BASE	.EQU	$EC		; LPT 1: REGISTERS BASE ADR
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO4BASE	.EQU	$90		; PIO: PIO REGISTERS BASE ADR FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)

Source/HBIOS/cfg_n8.asm

@@ -247,6 +247,12 @@ PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO4BASE	.EQU	$90		; PIO: PIO REGISTERS BASE ADR FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)

Source/HBIOS/cfg_rcz180.asm

@@ -257,6 +257,32 @@ PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
 PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
+LPTMODE		.EQU	LPTMODE_MG014	; LPT: DRIVER MODE: LPTMODE_[NONE|SPP|MG014]
+LPTCNT		.EQU	1		; LPT: NUMBER OF CHIPS TO DETECT (1-2)
+LPTTRACE	.EQU	1		; LPT: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+LPT0BASE	.EQU	$18		; LPT 0: REGISTERS BASE ADR
+LPT1BASE	.EQU	$00		; LPT 1: REGISTERS BASE ADR
+;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+PPACNT		.EQU	1		; PPA: NUMBER OF PPA DEVICES (1-2)
+PPATRACE	.EQU	1		; PPA: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+PPAMODE		.EQU	PPAMODE_MG014	; PPA: DRIVER MODE: PPAMODE_[NONE|SPP|MG014]
+PPA0BASE	.EQU	LPT0BASE	; PPA 0: BASE I/O ADDRESS OF PPI FOR PPA
+PPA1BASE	.EQU	LPT1BASE	; PPA 1: BASE I/O ADDRESS OF PPI FOR PPA
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+IMMCNT		.EQU	1		; IMM: NUMBER OF IMM DEVICES (1-2)
+IMMTRACE	.EQU	1		; IMM: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+IMMMODE		.EQU	IMMMODE_MG014	; IMM: DRIVER MODE: IMMMODE_[NONE|SPP|MG014]
+IMM0BASE	.EQU	LPT0BASE	; IMM 0: BASE I/O ADDRESS OF PPI FOR IMM
+IMM1BASE	.EQU	LPT1BASE	; IMM 1: BASE I/O ADDRESS OF PPI FOR IMM
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+SYQCNT		.EQU	1		; SYQ: NUMBER OF SYQ DEVICES (1-2)
+SYQTRACE	.EQU	1		; SYQ: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+SYQMODE		.EQU	IMMMODE_MG014	; SYQ: DRIVER MODE: SYQMODE_[NONE|SPP|MG014]
+SYQ0BASE	.EQU	LPT0BASE	; SYQ 0: BASE I/O ADDRESS OF PPI FOR SYQ
+SYQ1BASE	.EQU	LPT1BASE	; SYQ 1: BASE I/O ADDRESS OF PPI FOR SYQ
 ;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)

Source/HBIOS/cfg_rcz280.asm

@@ -20,7 +20,7 @@ CPUFAM		.EQU	CPU_Z280	; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
 HBIOS_MUTEX	.EQU	FALSE		; ENABLE REENTRANT CALLS TO HBIOS (ADDS OVERHEAD)
-USELZSA2	.EQU	FALSE		; ENABLE FONT COMPRESSION
+USELZSA2	.EQU	TRUE		; ENABLE FONT COMPRESSION
 TICKFREQ	.EQU	50		; DESIRED PERIODIC TIMER INTERRUPT FREQUENCY (HZ)
 ;
 BOOT_TIMEOUT	.EQU	-1		; AUTO BOOT TIMEOUT IN SECONDS, -1 TO DISABLE, 0 FOR IMMEDIATE
@@ -261,6 +261,32 @@ PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
 PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
+LPTMODE		.EQU	LPTMODE_MG014	; LPT: DRIVER MODE: LPTMODE_[NONE|SPP|MG014]
+LPTCNT		.EQU	1		; LPT: NUMBER OF CHIPS TO DETECT (1-2)
+LPTTRACE	.EQU	1		; LPT: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+LPT0BASE	.EQU	$18		; LPT 0: REGISTERS BASE ADR
+LPT1BASE	.EQU	$00		; LPT 1: REGISTERS BASE ADR
+;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+PPACNT		.EQU	1		; PPA: NUMBER OF PPA DEVICES (1-2)
+PPATRACE	.EQU	1		; PPA: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+PPAMODE		.EQU	PPAMODE_MG014	; PPA: DRIVER MODE: PPAMODE_[NONE|SPP|MG014]
+PPA0BASE	.EQU	LPT0BASE	; PPA 0: BASE I/O ADDRESS OF PPI FOR PPA
+PPA1BASE	.EQU	LPT1BASE	; PPA 1: BASE I/O ADDRESS OF PPI FOR PPA
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+IMMCNT		.EQU	1		; IMM: NUMBER OF IMM DEVICES (1-2)
+IMMTRACE	.EQU	1		; IMM: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+IMMMODE		.EQU	IMMMODE_MG014	; IMM: DRIVER MODE: IMMMODE_[NONE|SPP|MG014]
+IMM0BASE	.EQU	LPT0BASE	; IMM 0: BASE I/O ADDRESS OF PPI FOR IMM
+IMM1BASE	.EQU	LPT1BASE	; IMM 1: BASE I/O ADDRESS OF PPI FOR IMM
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+SYQCNT		.EQU	1		; SYQ: NUMBER OF SYQ DEVICES (1-2)
+SYQTRACE	.EQU	1		; SYQ: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+SYQMODE		.EQU	IMMMODE_MG014	; SYQ: DRIVER MODE: SYQMODE_[NONE|SPP|MG014]
+SYQ0BASE	.EQU	LPT0BASE	; SYQ 0: BASE I/O ADDRESS OF PPI FOR SYQ
+SYQ1BASE	.EQU	LPT1BASE	; SYQ 1: BASE I/O ADDRESS OF PPI FOR SYQ
 ;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)

Source/HBIOS/cfg_rcz80.asm

@@ -255,6 +255,32 @@ PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
 PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
+LPTMODE		.EQU	LPTMODE_MG014	; LPT: DRIVER MODE: LPTMODE_[NONE|SPP|MG014]
+LPTCNT		.EQU	1		; LPT: NUMBER OF CHIPS TO DETECT (1-2)
+LPTTRACE	.EQU	1		; LPT: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+LPT0BASE	.EQU	$0C		; LPT 0: REGISTERS BASE ADR
+LPT1BASE	.EQU	$00		; LPT 1: REGISTERS BASE ADR
+;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+PPACNT		.EQU	1		; PPA: NUMBER OF PPA DEVICES (1-2)
+PPATRACE	.EQU	1		; PPA: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+PPAMODE		.EQU	PPAMODE_MG014	; PPA: DRIVER MODE: PPAMODE_[NONE|SPP|MG014]
+PPA0BASE	.EQU	LPT0BASE	; PPA 0: BASE I/O ADDRESS OF PPI FOR PPA
+PPA1BASE	.EQU	LPT1BASE	; PPA 1: BASE I/O ADDRESS OF PPI FOR PPA
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+IMMCNT		.EQU	1		; IMM: NUMBER OF IMM DEVICES (1-2)
+IMMTRACE	.EQU	1		; IMM: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+IMMMODE		.EQU	IMMMODE_MG014	; IMM: DRIVER MODE: IMMMODE_[NONE|SPP|MG014]
+IMM0BASE	.EQU	LPT0BASE	; IMM 0: BASE I/O ADDRESS OF PPI FOR IMM
+IMM1BASE	.EQU	LPT1BASE	; IMM 1: BASE I/O ADDRESS OF PPI FOR IMM
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+SYQCNT		.EQU	1		; SYQ: NUMBER OF SYQ DEVICES (1-2)
+SYQTRACE	.EQU	1		; SYQ: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+SYQMODE		.EQU	IMMMODE_MG014	; SYQ: DRIVER MODE: SYQMODE_[NONE|SPP|MG014]
+SYQ0BASE	.EQU	LPT0BASE	; SYQ 0: BASE I/O ADDRESS OF PPI FOR SYQ
+SYQ1BASE	.EQU	LPT1BASE	; SYQ 1: BASE I/O ADDRESS OF PPI FOR SYQ
 ;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)

Source/HBIOS/cfg_rph.asm

@@ -236,6 +236,12 @@ PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO4BASE	.EQU	$90		; PIO: PIO REGISTERS BASE ADR FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)

Source/HBIOS/cfg_sbc.asm

@@ -234,9 +234,12 @@ PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
 PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
-LPTCNT		.EQU	1		; LPT: NUMBER OF CHIPS TO DETECT (1-2)
-LPT0BASE	.EQU	$E8		; LPT 0: REGISTERS BASE ADR
-LPT1BASE	.EQU	$EC		; LPT 1: REGISTERS BASE ADR
+;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
 ;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO4BASE	.EQU	$90		; PIO: PIO REGISTERS BASE ADR FOR ECB 4P BOARD

Source/HBIOS/cfg_scz180.asm

@@ -251,6 +251,32 @@ PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
 PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
+LPTMODE		.EQU	LPTMODE_MG014	; LPT: DRIVER MODE: LPTMODE_[NONE|SPP|MG014]
+LPTCNT		.EQU	1		; LPT: NUMBER OF CHIPS TO DETECT (1-2)
+LPTTRACE	.EQU	1		; LPT: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+LPT0BASE	.EQU	$18		; LPT 0: REGISTERS BASE ADR
+LPT1BASE	.EQU	$00		; LPT 1: REGISTERS BASE ADR
+;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+PPACNT		.EQU	1		; PPA: NUMBER OF PPA DEVICES (1-2)
+PPATRACE	.EQU	1		; PPA: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+PPAMODE		.EQU	PPAMODE_MG014	; PPA: DRIVER MODE: PPAMODE_[NONE|SPP|MG014]
+PPA0BASE	.EQU	LPT0BASE	; PPA 0: BASE I/O ADDRESS OF PPI FOR PPA
+PPA1BASE	.EQU	LPT1BASE	; PPA 1: BASE I/O ADDRESS OF PPI FOR PPA
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+IMMCNT		.EQU	1		; IMM: NUMBER OF IMM DEVICES (1-2)
+IMMTRACE	.EQU	1		; IMM: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+IMMMODE		.EQU	IMMMODE_MG014	; IMM: DRIVER MODE: IMMMODE_[NONE|SPP|MG014]
+IMM0BASE	.EQU	LPT0BASE	; IMM 0: BASE I/O ADDRESS OF PPI FOR IMM
+IMM1BASE	.EQU	LPT1BASE	; IMM 1: BASE I/O ADDRESS OF PPI FOR IMM
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+SYQCNT		.EQU	1		; SYQ: NUMBER OF SYQ DEVICES (1-2)
+SYQTRACE	.EQU	1		; SYQ: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+SYQMODE		.EQU	IMMMODE_MG014	; SYQ: DRIVER MODE: SYQMODE_[NONE|SPP|MG014]
+SYQ0BASE	.EQU	LPT0BASE	; SYQ 0: BASE I/O ADDRESS OF PPI FOR SYQ
+SYQ1BASE	.EQU	LPT1BASE	; SYQ 1: BASE I/O ADDRESS OF PPI FOR SYQ
 ;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)

Source/HBIOS/cfg_z80retro.asm

@@ -206,6 +206,12 @@ PIOENABLE	.EQU	FALSE		; PIO: ENABLE ZILOG PIO DRIVER (PIO.ASM)
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)
 PIO_SBC		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR 8255 CHIP

Source/HBIOS/cfg_zeta.asm

@@ -177,6 +177,12 @@ PIOENABLE	.EQU	FALSE		; PIO: ENABLE ZILOG PIO DRIVER (PIO.ASM)
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)
 PIO_SBC		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR 8255 CHIP

Source/HBIOS/cfg_zeta2.asm

@@ -188,6 +188,12 @@ PIOENABLE	.EQU	FALSE		; PIO: ENABLE ZILOG PIO DRIVER (PIO.ASM)
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)
 PIO_SBC		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR 8255 CHIP

Source/HBIOS/hbios.asm

@@ -1261,11 +1261,11 @@ Z280_INITZ:
 
 	; SET DEFAULT CPU CLOCK MULTIPLIERS (XTAL / 2)
 	;
-	; IT HAS BEEN REPORTED THAT CMR NEEDS TO BE SET PRIOR TO CCR
-	; WHEN USING AN INPUT FREQUENCY THAT IS XTAL / 2.
-	; I NEVER EXPERIENCED A PROBLEM RELATED TO ORDER, BUT JUST
+	; BILL MCMULLEN REPORTED THAT CMR NEEDS TO BE SET PRIOR TO CCR
+	; WHEN USING A CPU FREQUENCY (PHI) THAT IS XTAL * 2.
+	; HERE WE ARE SETTING CPU FREQUENCY TO XTAL / 2, BUT JUST
 	; FOR GOOD MEASURE, CMR IS SET PRIOR TO CCR BELOW.
-	; https://www.retrobrewcomputers.org/forum/index.php?t=msg&th=316&#msg_5045
+	; https://www.retrobrewcomputers.org/forum/index.php?t=msg&th=316&goto=5045&#msg_5045
 	XOR	A
 	OUT0	(Z180_CMR),A
 	OUT0	(Z180_CCR),A
@@ -3239,6 +3239,15 @@ HB_INITTBL:
 #IF (HDSKENABLE)
 	.DW	HDSK_INIT
 #ENDIF
+#IF (PPAENABLE)
+	.DW	PPA_INIT
+#ENDIF
+#IF (IMMENABLE)
+	.DW	IMM_INIT
+#ENDIF
+#IF (SYQENABLE)
+	.DW	SYQ_INIT
+#ENDIF
 #IF (PRPENABLE)
 	.DW	PRP_INIT
 #ENDIF
@@ -6225,6 +6234,16 @@ FONTCGA:
 	.ECHO	" CGA"
 #ENDIF
 ;
+#IFDEF USEFONTVGARC
+FONTVGARC:
+  #IF USELZSA2
+    #INCLUDE "fontvgarcc.asm"
+  #ELSE
+    #INCLUDE "fontvgarcu.asm"
+  #ENDIF
+	.ECHO	" VGARC"
+#ENDIF
+;
 SIZ_FONTS	.EQU	$ - ORG_FONTS
 		.ECHO	" occupy "
 		.ECHO	SIZ_FONTS
@@ -6338,6 +6357,33 @@ SIZ_HDSK	.EQU	$ - ORG_HDSK
 		.ECHO	" bytes.\n"
 #ENDIF
 ;
+#IF (PPAENABLE)
+ORG_PPA		.EQU	$
+  #INCLUDE "ppa.asm"
+SIZ_PPA		.EQU	$ - ORG_PPA
+		.ECHO	"PPA occupies "
+		.ECHO	SIZ_PPA
+		.ECHO	" bytes.\n"
+#ENDIF
+;
+#IF (IMMENABLE)
+ORG_IMM		.EQU	$
+  #INCLUDE "imm.asm"
+SIZ_IMM		.EQU	$ - ORG_IMM
+		.ECHO	"IMM occupies "
+		.ECHO	SIZ_IMM
+		.ECHO	" bytes.\n"
+#ENDIF
+;
+#IF (SYQENABLE)
+ORG_SYQ		.EQU	$
+  #INCLUDE "syq.asm"
+SIZ_SYQ		.EQU	$ - ORG_SYQ
+		.ECHO	"SYQ occupies "
+		.ECHO	SIZ_SYQ
+		.ECHO	" bytes.\n"
+#ENDIF
+;
 #IF (TERMENABLE)
 ORG_TERM	.EQU	$
   #INCLUDE "term.asm"
@@ -6752,7 +6798,6 @@ PS_PRTDC:
 	RES	7,D			; CLEAR LBA BIT
 	LD	B,11			; 11 BIT SHIFT TO CONVERT BLOCKS --> MB
 	CALL	SRL32			; RIGHT SHIFT
-	;CALL	PRTDEC			; PRINT LOW WORD IN DECIMAL (HIGH WORD DISCARDED)
 	CALL	PRTDEC32		; PRINT DWORD IN DECIMAL
 	PRTS("MB$")			; PRINT SUFFIX
 	CALL	PC_COMMA
@@ -6767,7 +6812,6 @@ PS_PRTDC1:
 	RES	7,D			; CLEAR LBA BIT
 	LD	B,1			; 11 BIT SHIFT TO CONVERT BLOCKS --> MB
 	CALL	SRL32			; RIGHT SHIFT
-	;CALL	PRTDEC			; PRINT LOW WORD IN DECIMAL (HIGH WORD DISCARDED)
 	CALL	PRTDEC32		; PRINT DWORD IN DECIMAL
 	PRTS("KB$")			; PRINT SUFFIX
 	CALL	PC_COMMA
@@ -7124,6 +7168,9 @@ PS_DDSD		.TEXT	"SD$"
 PS_DDPRPSD	.TEXT	"PRPSD$"
 PS_DDPPPSD	.TEXT	"PPPSD$"
 PS_DDHDSK	.TEXT	"HDSK$"
+PS_DDPPA	.TEXT	"PPA$"
+PS_DDIMM	.TEXT	"IMM$"
+PS_DDSYQ	.TEXT	"SYQ$"
 ;
 ; DISK TYPE STRINGS
 ;
@@ -7536,6 +7583,52 @@ HB_HASFP	.DB	0		; NON-ZERO MEANS FP EXISTS
 ;
 HB_WRKBUF	.FILL	512,0		; INTERNAL DISK BUFFER
 ;
+;
+;
+#IFDEF MG014_MAP
+;
+	.FILL	32 - ($ & (32 - 1))	; ALIGN TO 32 BYTE BOUNDARY
+
+MG014_STATMAPLO:
+	; LOWER NIBBLE
+	.DB	$08	; 00
+	.DB	$0C	; 01
+	.DB	$00	; 02
+	.DB	$04	; 03
+	.DB	$0A	; 04
+	.DB	$0E	; 05
+	.DB	$02	; 06
+	.DB	$06	; 07
+	.DB	$09	; 08
+	.DB	$0D	; 09
+	.DB	$01	; 0A
+	.DB	$05	; 0B
+	.DB	$0B	; 0C
+	.DB	$0F	; 0D
+	.DB	$03	; 0E
+	.DB	$07	; 0F
+;
+MG014_STATMAPHI:
+	; UPPER NIBBLE
+	.DB	$80	; 00
+	.DB	$C0	; 01
+	.DB	$00	; 02
+	.DB	$40	; 03
+	.DB	$A0	; 04
+	.DB	$E0	; 05
+	.DB	$20	; 06
+	.DB	$60	; 07
+	.DB	$90	; 08
+	.DB	$D0	; 09
+	.DB	$10	; 0A
+	.DB	$50	; 0B
+	.DB	$B0	; 0C
+	.DB	$F0	; 0D
+	.DB	$30	; 0E
+	.DB	$70	; 0F
+;
+#ENDIF
+;
 HB_END		.EQU	$
 ;
 SLACK		.EQU	BNKTOP - $

Source/HBIOS/hbios.inc

@@ -321,6 +321,9 @@ DIODEV_SD	.EQU	$60
 DIODEV_PRPSD	.EQU	$70
 DIODEV_PPPSD	.EQU	$80
 DIODEV_HDSK	.EQU	$90
+DIODEV_PPA	.EQU	$A0
+DIODEV_IMM	.EQU	$B0
+DIODEV_SYQ	.EQU	$C0
 ;
 ; RTC DEVICE IDS
 ;

Source/HBIOS/lpt.asm

@@ -3,13 +3,17 @@
 ; CENTRONICS (LPT) INTERFACE DRIVER
 ;==================================================================================================
 ;
-; CENTRONICS-STYLE PARALLEL PRINTER DRIVER.  ASSUMES IBM STYLE
-; HARDWARE INTERFACE AS DESCRIBED BELOW.
+; CENTRONICS-STYLE PARALLEL PRINTER DRIVER.
 ;
 ; IMPLEMENTED AS A ROMWBW CHARACTER DEVICE.  CURRENTLY HANDLES OUPUT
 ; ONLY.
 ;
-;  PORT 0 (INPUT/OUTPUT):
+;==================================================================================================
+;
+;  IBM PC STANDARD PARALLEL PORT (SPP):
+;  - NHYODYNE PRINT MODULE
+;
+;  PORT 0 (OUTPUT):
 ;
 ;	D7	D6	D5	D4	D3	D2	D1	D0
 ;     +-------+-------+-------+-------+-------+-------+-------+-------+
@@ -20,26 +24,51 @@
 ;
 ;	D7	D6	D5	D4	D3	D2	D1	D0
 ;     +-------+-------+-------+-------+-------+-------+-------+-------+
-;     | BUSY  | ACK   | POUT  | SEL   | ERR   | 0     | 0     | 0     |
+;     | /BUSY | /ACK  | POUT  | SEL   | /ERR  | 0     | 0     | 0     |
 ;     +-------+-------+-------+-------+-------+-------+-------+-------+
 ;
-;  PORT 2 (INPUT/OUTPUT):
+;  PORT 2 (OUTPUT):
 ;
 ;	D7	D6	D5	D4	D3	D2	D1	D0
 ;     +-------+-------+-------+-------+-------+-------+-------+-------+
 ;     | STAT1 | STAT0 | ENBL  | PINT  | SEL   | RES   | LF    | STB   |
 ;     +-------+-------+-------+-------+-------+-------+-------+-------+
 ;
-LPT_NONE	.EQU	0		; NOT PRESENT
-LPT_IBM		.EQU	1		; IBM PC STYLE INTERFACE
+;==================================================================================================
+;
+;  MG014 STYLE INTERFACE:
+;  - RCBUS MG014 MODULE
+;
+;  PORT 0 (OUTPUT):
+;
+;	D7	D6	D5	D4	D3	D2	D1	D0
+;     +-------+-------+-------+-------+-------+-------+-------+-------+
+;     | PD7   | PD6   | PD5   | PD4   | PD3   | PD2   | PD1   | PD0   |
+;     +-------+-------+-------+-------+-------+-------+-------+-------+
+;
+;  PORT 1 (INPUT):
+;
+;	D7	D6	D5	D4	D3	D2	D1	D0
+;     +-------+-------+-------+-------+-------+-------+-------+-------+
+;     |	      |	      |	      | /ERR  | SEL   | POUT  | BUSY  | /ACK  |
+;     +-------+-------+-------+-------+-------+-------+-------+-------+
+;
+;  PORT 2 (OUTPUT):
+;
+;	D7	D6	D5	D4	D3	D2	D1	D0
+;     +-------+-------+-------+-------+-------+-------+-------+-------+
+;     | LED   |	      |	      |	      | /SEL  | /RES  | /LF   | /STB  |
+;     +-------+-------+-------+-------+-------+-------+-------+-------+
+;
+;==================================================================================================
 ;
 ; PRE-CONSOLE INITIALIZATION - DETECT AND INIT HARDWARE
 ;
 LPT_PREINIT:
 ;
 ; SETUP THE DISPATCH TABLE ENTRIES
-; NOTE: INTS WILL BE DISABLED WHEN PREINIT IS CALLED AND THEY MUST REMIAIN
-; DISABLED.
+; NOTE: INTS WILL BE DISABLED WHEN PREINIT IS CALLED AND THEY MUST
+; REMAIN DISABLED.
 ;
 	LD	B,LPT_CFGCNT		; LOOP CONTROL
 	XOR	A			; ZERO TO ACCUM
@@ -136,18 +165,26 @@ LPT_IN:
 LPT_OUT:
 	CALL	LPT_OST			; READY TO SEND?
 	JR	Z,LPT_OUT		; LOOP IF NOT
-	LD	A,(IY+3)
-	LD	C,A			; PORT 0 (DATA)
- 	OUT	(C),E			; OUTPUT DATA TO PORT
- 	CALL 	DELAY   		; IGNORE ANYTHING BACK AFTER A RESET
-        LD      A,%00001101             ; SELECT & STROBE, LEDS OFF
-	INC 	C 			; PUT CONTROL PORT IN C
-	INC 	C
-        OUT	(C),A			; OUTPUT DATA TO PORT
-  	CALL 	DELAY   		; IGNORE ANYTHING BACK AFTER A RESET
-        LD      A,%00001100             ; SELECT, LEDS OFF
-        OUT	(C),A			; OUTPUT DATA TO PORT
-
+	LD	C,(IY+3)		; PORT 0 (DATA)
+	OUT	(C),E			; OUTPUT DATA TO PORT
+#IF (LPTMODE == LPTMODE_SPP)
+	LD	A,%00001101		; SELECT & STROBE, LEDS OFF
+#ENDIF
+#IF (LPTMODE == LPTMODE_MG014)
+	LD	A,%00000100		; SELECT & STROBE, LED OFF
+#ENDIF
+	INC	C			; PUT CONTROL PORT IN C
+	INC	C
+	OUT	(C),A			; OUTPUT DATA TO PORT
+	CALL	DELAY
+#IF (LPTMODE == LPTMODE_SPP)
+	LD	A,%00001100		; SELECT, LEDS OFF
+#ENDIF
+#IF (LPTMODE == LPTMODE_MG014)
+	LD	A,%00000101		; SELECT, LED OFF
+#ENDIF
+	OUT	(C),A			; OUTPUT DATA TO PORT
+	CALL	DELAY
 	XOR	A			; SIGNAL SUCCESS
 	RET
 ;
@@ -161,11 +198,16 @@ LPT_IST:
 ; OUTPUT STATUS
 ;
 LPT_OST:
-	LD	A,(IY+3)
-	LD	C,A			; PORT 0 (DATA)
-	INC 	C			; SELECT STATUS PORT
- 	IN	A,(C)			; GET STATUS INFO
-    	AND	%10000000		; ONLY INTERESTED IN BUSY FLAG
+	LD	C,(IY+3)		; BASE PORT
+	INC	C			; SELECT STATUS PORT
+	IN	A,(C)			; GET STATUS INFO
+#IF (LPTMODE == LPTMODE_SPP)
+	AND	%10000000		; ISOLATE /BUSY
+#ENDIF
+#IF (LPTMODE == LPTMODE_MG014)
+	AND	%00000010		; ISOLATE BUSY
+	XOR	%00000010		; INVERT TO READY
+#ENDIF
 	RET				; DONE
 ;
 ; INITIALIZE DEVICE
@@ -180,20 +222,40 @@ LPT_INITDEV:
 ; PREINIT ABOVE.  PREINIT IS NOT ALLOWED TO ENABLE INTS!
 ;
 LPT_INITDEVX:
-	LD	A,(IY+3)
-	LD	C,A			; PORT 0 (DATA)
+;
+#IF (LPTMODE == LPTMODE_SPP)
+;
+	LD	C,(IY+3)		; PORT 0 (DATA)
 	XOR	A			; CLEAR ACCUM
 	OUT	(C),A			; SEND IT
 	INC	C			; BUMP TO
 	INC	C			; ... PORT 2
 	LD	A,%00001000		; SELECT AND ASSERT RESET, LEDS OFF
 	OUT	(C),A			; SEND IT
- 	CALL	LDELAY			; HALF SECOND DELAY
+	CALL	LDELAY			; HALF SECOND DELAY
 	LD	A,%00001100		; SELECT AND DEASSERT RESET, LEDS OFF
 	OUT	(C),A			; SEND IT
 	XOR	A			; SIGNAL SUCCESS
 	RET				; RETURN
 ;
+#ENDIF
+;
+#IF (LPTMODE == LPTMODE_MG014)
+	LD	A,(IY+3)		; BASE PORT
+	ADD	A,3			; BUMP TO CONTROL PORT
+	LD	C,A			; MOVE TO C FOR I/O
+	LD	A,$82			; CONFIG A OUT, B IN, C OUT
+	OUT	(C),A			; DO IT
+	DEC	C			; OUTPUT PORT
+	LD	A,$81			; STROBE OFF, SELECT ON, RES ON, LED ON
+	OUT	(C),A			; SEND IT
+	CALL	LDELAY			; HALF SECOND DELAY
+	LD	A,$05			; STROBE OFF, SELECT ON, RES OFF, LED OFF
+	OUT	(C),A			; SEND IT
+	XOR	A			; SIGNAL SUCCESS
+	RET				; RETURN
+#ENDIF
+;
 ;
 ;
 LPT_QUERY:
@@ -215,17 +277,26 @@ LPT_DEVICE:
 ;
 ; LPT DETECTION ROUTINE
 ;
+#IF (LPTMODE == LPTMODE_NONE)
+;
 LPT_DETECT:
-	LD	A,(IY+3)		; BASE PORT ADDRESS
-	LD	C,A			; PUT IN C FOR I/O
+	LD	A,LPTMODE_NONE		; NOTHING TO DETECT
+	RET
+;
+#ENDIF
+;
+#IF (LPTMODE == LPTMODE_SPP)
+;
+LPT_DETECT:
+	LD	C,(IY+3)		; BASE PORT ADDRESS
 	CALL	LPT_DETECT2		; CHECK IT
 	JR	Z,LPT_DETECT1		; FOUND IT, RECORD IT
-	LD	A,LPT_NONE		; NOTHING FOUND
+	LD	A,LPTMODE_NONE		; NOTHING FOUND
 	RET				; DONE
 ;
 LPT_DETECT1:
 	; LPT FOUND, RECORD IT
-	LD	A,LPT_IBM		; RETURN CHIP TYPE
+	LD	A,LPTMODE_SPP		; RETURN CHIP TYPE
 	RET				; DONE
 ;
 LPT_DETECT2:
@@ -253,6 +324,43 @@ LPT_DETECT2:
 	CP	$A5			; CORRECT?
 	RET				; RETURN (ZF SET CORRECTLY)
 ;
+#ENDIF
+;
+#IF (LPTMODE == LPTMODE_MG014)
+LPT_DETECT:
+;
+	; TEST FOR PPI EXISTENCE
+	; WE SETUP THE PPI TO WRITE, THEN WRITE A VALUE OF $A5
+	; TO PORT A (DATALO), THEN READ IT BACK.  IF THE PPI IS THERE
+	; THEN THE BUS HOLD CIRCUITRY WILL READ BACK THE $A5. SINCE
+	; WE ARE IN WRITE MODE, AN IDE CONTROLLER WILL NOT BE ABLE TO
+	; INTERFERE WITH THE VALUE BEING READ.
+;
+	LD	A,(IY+3)		; BASE IO ADDRESS
+	ADD	A,3			; BUMP TO CONTROL PORT
+	LD	C,A			; PUT IN C
+	LD	A,$80			; SET PORT A TO WRITE
+	OUT	(C),A			; WRITE IT
+;
+	LD	C,(IY+3)		; PPI PORT A
+	LD	A,$A5			; TEST VALUE
+	OUT	(C),A			; PUSH VALUE TO PORT
+	IN	A,(C)			; GET PORT VALUE
+#IF (LPTTRACE >= 3)
+	CALL	PC_SPACE
+	CALL	PRTHEXBYTE
+#ENDIF
+	CP	$A5			; CHECK FOR TEST VALUE
+	JR	Z,LPT_DETECT1		; FOUND IT
+	LD	A,LPTMODE_NONE		; NOT FOUND
+	RET
+;
+LPT_DETECT1:
+	; LPT FOUND, RECORD IT
+	LD	A,LPTMODE_MG014		; RETURN CHIP TYPE
+	RET				; DONE
+#ENDIF
+;
 ;
 ;
 LPT_PRTCFG:
@@ -266,7 +374,7 @@ LPT_PRTCFG:
 	CALL	PRTHEXBYTE		; PRINT BASE PORT
 
 	; PRINT THE LPT TYPE
-	CALL	PC_SPACE		; FORMATTING
+	PRTS(" MODE=$")			; FORMATTING
 	LD	A,(IY+1)		; GET LPT TYPE BYTE
 	RLCA				; MAKE IT A WORD OFFSET
 	LD	HL,LPT_TYPE_MAP		; POINT HL TO TYPE MAP TABLE
@@ -290,10 +398,12 @@ LPT_PRTCFG:
 ;
 LPT_TYPE_MAP:
 		.DW	LPT_STR_NONE
-		.DW	LPT_STR_IBM
+		.DW	LPT_STR_SPP
+		.DW	LPT_STR_MG014
 ;
 LPT_STR_NONE	.DB	"<NOT PRESENT>$"
-LPT_STR_IBM	.DB	"IBM$"
+LPT_STR_SPP	.DB	"SPP$"
+LPT_STR_MG014	.DB	"MG014$"
 ;
 ; WORKING VARIABLES
 ;

Source/HBIOS/ppp.asm

@@ -904,7 +904,7 @@ PPPSD_GETCSD:
 	CALL	PPP_SNDCMD		; SEND COMMAND
 	RET	NZ			; ABORT ON ERROR
 
-	LD	B,16			; GET 4 BYTES
+	LD	B,16			; GET 16 BYTES
 	LD	HL,PPPSD_CSDBUF
 PPPSD_GETCSD1:
 	CALL	PPP_GETBYTE

Source/HBIOS/romldr.asm

@@ -180,7 +180,7 @@ start1:
 	call	pstr			; do it
 	call	clrbuf			; zero fill the cmd buffer
 ;
-#if (BIOS == BIOS_WBW)
+#if ((BIOS == BIOS_WBW) & FPSW_ENABLE)
 ;
 	ld	b,BF_SYSGET		; HBIOS SysGet
 	ld	c,BF_SYSGET_PANEL	; ... Panel swiches value
@@ -390,7 +390,7 @@ runcmd2:
 	ld	(bootslice),a		; save boot slice
 	jp	diskboot		; boot the disk unit/slice
 ;
-#if (BIOS == BIOS_WBW)
+#if ((BIOS == BIOS_WBW) & FPSW_ENABLE)
 ;
 ;=======================================================================
 ; Process Front Panel switches

Source/HBIOS/std.asm

@@ -242,6 +242,30 @@ GDCMODE_NONE	.EQU	0
 GDCMODE_ECB	.EQU	1		; ECB GDC
 GDCMODE_RPH	.EQU	2		; RPH GDC
 ;
+; LPT DRIVER MODE SELECTIONS
+;
+LPTMODE_NONE	.EQU	0		; NONE
+LPTMODE_SPP	.EQU	1		; IBM PC STANDARD PAR PORT (SPP)
+LPTMODE_MG014	.EQU	2		; RCBUS MG014 STYLE INTERFACE
+;
+; PPA DRIVER MODE SELECTIONS
+;
+PPAMODE_NONE	.EQU	0		; NONE
+PPAMODE_SPP	.EQU	1		; IBM PC STANDARD PAR PORT (SPP)
+PPAMODE_MG014	.EQU	2		; RCBUS MG014 STYLE INTERFACE
+;
+; IMM DRIVER MODE SELECTIONS
+;
+IMMMODE_NONE	.EQU	0		; NONE
+IMMMODE_SPP	.EQU	1		; IBM PC STANDARD PAR PORT (SPP)
+IMMMODE_MG014	.EQU	2		; RCBUS MG014 STYLE INTERFACE
+;
+; SYQ DRIVER MODE SELECTIONS
+;
+SYQMODE_NONE	.EQU	0		; NONE
+SYQMODE_SPP	.EQU	1		; IBM PC STANDARD PAR PORT (SPP)
+SYQMODE_MG014	.EQU	2		; RCBUS MG014 STYLE INTERFACE
+;
 ; GDC MONITOR SELECTIONS
 ;
 GDCMON_NONE	.EQU	0
@@ -431,6 +455,16 @@ SPD_UNSUP	.EQU	0		; PLATFORM CAN CHANGE SPEEDS BUT IS UNSUPPORTED
 SPD_HIGH	.EQU	1		; PLATFORM CAN CHANGE SPEED, STARTS HIGH
 SPD_LOW		.EQU	2		; PLATFORM CAN CHANGE SPEED, STARTS LOW
 ;
+; SCSI COMMAND CODES (SHOULD BE IT IT'S OWN FILE)
+;
+SCSI_CMD_READ	.EQU	$08
+SCSI_CMD_INQ	.EQU	$12
+SCSI_CMD_TEST	.EQU	$00
+SCSI_CMD_START	.EQU	$1B
+SCSI_CMD_SENSE	.EQU	$03
+SCSI_CMD_WRITE	.EQU	$0A
+SCSI_CMD_RDCAP	.EQU	$25
+;
 #INCLUDE "build.inc"		; INCLUDE USER CONFIG, ADD VARIANT, TIMESTAMP, & ROMSIZE
 ;
 ; INCLUDE Z180 REGISTER DEFINITIONS

Source/HBIOS/unlzsa2s.asm

@@ -60,8 +60,8 @@
 ;  3. This notice may not be removed or altered from any source distribution.
 ;
 
-;	#DEFINE	BACKWARD_DECOMPRESS						; uncomment for data compressed with option -b (+5 bytes, -3% speed)
-;	#DEFINE	AVOID_SELFMODIFYING_CODE					; uncomment to disallow self-modifying code (-1 byte, -4% speed)
+;	#DEFINE	BACKWARD_DECOMPRESS		; uncomment for data compressed with option -b (+5 bytes, -3% speed)
+;	#DEFINE	AVOID_SELFMODIFYING_CODE	; uncomment to disallow self-modifying code (-1 byte, -4% speed)
 
 	#IFNDEF	BACKWARD_DECOMPRESS
 
@@ -79,7 +79,7 @@
 
 		#DEFINE ADD_OFFSET \
 		#DEFCONT \ ld a,e \ sub l \ ld l,a
-		#DEFCONT \ ld a,d \ sbc h \ ld h,a						; 6*4 = 24t / 6 bytes
+		#DEFCONT \ ld a,d \ sbc h \ ld h,a	; 6*4 = 24t / 6 bytes
 
 		#DEFINE BLOCKCOPY \
 		#DEFCONT \ lddr
@@ -118,7 +118,7 @@ MatchLen:		and %00000111 \ add a,2 \ cp 9
 			call z,ExtendedCode
 
 CopyMatch:		ld c,a
-			push hl						; BC = len, DE = dest, HL = -offset, SP -> [src]
+			push hl		; BC = len, DE = dest, HL = -offset, SP -> [src]
 
 	#IFNDEF	AVOID_SELFMODIFYING_CODE
 PrevOffset		.EQU $+1 \ ld hl,0
@@ -126,8 +126,8 @@ PrevOffset		.EQU $+1 \ ld hl,0
 			push ix \ pop hl
 	#ENDIF
 			ADD_OFFSET
-			BLOCKCOPY					; BC = 0, DE = dest
-			pop hl						; HL = src
+			BLOCKCOPY	; BC = 0, DE = dest
+			pop hl		; HL = src
 
 ReadToken:	ld a,(hl) \ NEXT_HL \ push af
 		and %00011000 \ jr z,NoLiterals
@@ -163,12 +163,16 @@ ExtendedCode:	call ReadNibble \ inc a \ jr z,ExtraByte
 ExtraByte	ld a,15 \ add a,c \ add a,(hl) \ NEXT_HL \ ret nc
 		ld a,(hl) \ NEXT_HL
 		ld b,(hl) \ NEXT_HL \ ret nz
-		pop bc								; RET is not needed, because RET from ReadNibble is sufficient
+		pop bc			; RET is not needed, because RET from ReadNibble is sufficient
 
 
 ReadNibble:	ld c,a
-skipLDCA	xor a \ ex af,af' \ ret m
+skipLDCA	xor a \ nop \ ex af,af' \ ret m		; NOP for Z280 bug
 		ld a,(hl) \ or $F0 \ ex af,af'
 		ld a,(hl) \ NEXT_HL \ or $0F
 		rrca \ rrca \ rrca \ rrca \ ret
 
+; The extraneous NOP instruction above is to workaround a bug in the
+; Z280 processor where ex af,af' can copy rather than swap the flags
+; register.
+; See https://www.retrobrewcomputers.org/forum/index.php?t=msg&goto=10183&

Source/HBIOS/vrc.asm

@@ -21,8 +21,8 @@ VRC_KBDST	.EQU	$F5
 VRC_ROWS	.EQU	48
 VRC_COLS	.EQU	64
 ;
-#DEFINE USEFONT8X8
-#DEFINE	VRC_FONT FONT8X8
+#DEFINE USEFONTVGARC
+#DEFINE	VRC_FONT FONTVGARC
 ;
 TERMENABLE	.SET	TRUE		; INCLUDE TERMINAL PSEUDODEVICE DRIVER
 ;
@@ -283,9 +283,14 @@ VRC_LOADFONT:
 	LD	HL,VRC_FONT		; START OF FONT DATA
 #ENDIF
 ;
+#IF 0
+	; THIS APPROACH TO LOADING FONTS IS BEST (FASTEST), BUT IS
+	; CAUSING ARTIFACTS ON THE DISPLAYED FONTS WHEN RUN ON A
+	; Z280.  IT IS NOT CLEAR WHAT THE PROBLEM IS (POSSIBLY
+	; Z280 BUG), BUT FOR NOW WE AVOID THIS AND USE AN
+	; ALTERNATIVE APPROACH BELOW.
 	LD	DE,0+(128*8)-1		; LENGTH OF FONT DATA - 1
 	ADD	HL,DE			; ADD TO HL
-;	LD	HL,ENDFONT-1
 	LD	BC,VRC_FONTBASE+3	; WORK BACKWARDS
 	OTDR				; DO 4 PAGES
 	DEC	C
@@ -295,6 +300,24 @@ VRC_LOADFONT:
 	DEC	C
 	OTDR
 	DEC	C
+#ENDIF
+;
+#IF 1
+	; ALTERNATIVE APPROACH TO LOADING FONTS.  THIS ONE AVOIDS
+	; THE USE OF OTDR WHICH SEEMS TO CAUSE PROBLEMS ON Z280.
+	LD	B,0
+	LD	C,VRC_FONTBASE
+VRC_LOADFONT1:
+	LD	A,(HL)
+	OUT	(C),A
+	INC	HL
+	INC	B
+	JR	NZ,VRC_LOADFONT1
+	INC	C
+	LD	A,C
+	CP	VRC_FONTBASE + 4
+	JR	NZ,VRC_LOADFONT1
+#ENDIF
 ;
 #IF USELZSA2
 	LD	HL,(VRC_STACK)		; ERASE DECOMPRESS BUFFER

Source/pSys/ReadMe.txt

@@ -48,7 +48,7 @@ The layout of the first track does not conform exactly to the
 recommended p-System layout.  The recommended layout is not possible 
 because it conflicts with the RomWBW definition for a boot track.  
 However, the changes are only slightly different sector assignments for 
-the different boot componets -- the general boot sequence and mechanism 
+the different boot components -- the general boot sequence and mechanism 
 for the p-System is completely standard.
 
 The logical disk geometry used by this p-System
@@ -77,14 +77,17 @@ escape sequence handling configuration.  The debugger code as added to
 SYSTEM.PASCAL to enable the debug function.  SYSTEM.INTERP was modified 
 to enable the extended BIOS functions.
 
-The build/makefile creates the psys disk image (psys.img) by adding 
-concatentating psys.vol and blank.vol (after adding track 0 contents to 
+The build/makefile creates the psys disk image (psys.img) by 
+concatenating psys.vol and blank.vol (after adding track 0 contents to 
 each).  psys.vol and blank.vol are recognized by CiderPress and 
 CiderPress can be used to add/remove files from these volumes.  
-However, there is currently no straightforward way to extract the 
-volumes from the disk image.  If you are good with a binary disk 
-editor, you can do it that way.  Please contact me if you are 
-interested in pursuing that.
+To extract volumes from a disk image, Andrew Davidson has created
+a nice Python script that can extract p-System volumes from an
+existing disk image file.  The extracted volume can be manipulated
+by CiderPress.  The script is also capable of re-inserting a modified
+volume back into the disk image file.  This tool is available at:
+https://github.com/robosnacks/psysimg.
+
 
 There is currently no support for floppy drives.
 
@@ -119,7 +122,7 @@ that SofTech produced a IV.1 with some nice enhancements (like
 subsidiary volumes and decent support for ANSI/VT-100 terminals).  I
 have been unable to track down the IV.1 distribution media despite
 trying very hard.  If anyone knows of a source for the media of the
-Adapable p-System for Z80, I would love to get hold of it.
+Adaptable p-System for Z80, I would love to get hold of it.
 
 3:58 PM Tuesday, January 17, 2023
 
@@ -138,4 +141,10 @@ arrow keys transmitted by an ANSI/VT-100 terminal.  In this case,
 the setup program was used to define up/down/left/right like
 WordStar does: ^E,^X,^S,^D.
 
-5:48 PM Tuesday, January 17, 2023
+5:48 PM Tuesday, January 17, 2023
+
+Updated instructions above to include a reference to Andrew 
+Davidson's Python script that will extract/insert volumes from/to
+a disk image.
+
+1:31 PM Thursday, May 11, 2023

Source/ver.inc

@@ -2,7 +2,7 @@
 #DEFINE	RMN	3
 #DEFINE	RUP	0
 #DEFINE	RTP	0
-#DEFINE BIOSVER	"3.3.0-dev.10"
+#DEFINE BIOSVER	"3.3.0-dev.22"
 #define rmj	RMJ
 #define rmn	RMN
 #define rup	RUP

Source/ver.lib

@@ -3,5 +3,5 @@ rmn	equ	3
 rup	equ	0
 rtp	equ	0
 biosver	macro
-	db	"3.3.0-dev.10"
+	db	"3.3.0-dev.22"
 	endm