Small Bug Fix for PPA/IMM/SYQ Drivers

Credit to Mark Elkin for testing and finding this issue.

Doc/ChangeLog.txt

@@ -7,6 +7,9 @@ Version 3.3
 - WBW: Support per-drive floppy configuration
 - WBW: Support for Bill Shen's VGARC
 - WBW: Support for MG014 Parallel Port module + printer
+- WBW: Support for EMM Zip Drive on PPI interface (much inspiration from Alan Cox)
+- WBW: Support for PPA Zip Drive on PPI interface (much inspiration from Alan Cox)
+- WBW: Support for SyQuest SparQ Drive on PPI interface (much inspiration from Alan Cox)
 
 Version 3.2.1
 -------------

ReadMe.md

@@ -3,7 +3,7 @@
 **RomWBW ReadMe** \
 Version 3.3 \
 Wayne Warthen  ([wwarthen@gmail.com](mailto:wwarthen@gmail.com)) \
-03 May 2023
+02 Jun 2023
 
 # Overview
 

ReadMe.txt

@@ -1,6 +1,6 @@
 RomWBW ReadMe
 Wayne Warthen (wwarthen@gmail.com)
-03 May 2023
+02 Jun 2023
 
 
 

Source/Apps/assign.asm

@@ -1918,9 +1918,9 @@ dev06	.db	"SD",0
 dev07	.db	"PRPSD",0
 dev08	.db	"PPPSD",0
 dev09	.db	"HDSK",0
-dev10	.equ	devunk
-dev11	.equ	devunk
-dev12	.equ	devunk
+dev10	.db	"PPA",0
+dev11	.db	"IMM",0
+dev12	.db	"SYQ",0
 dev13	.equ	devunk
 dev14	.equ	devunk
 dev15	.equ	devunk

Source/CBIOS/cbios.asm

@@ -2929,6 +2929,14 @@ DRV_INIT3:
 	RET
 ;
 DRV_INIT3A:
+	; CHECK FOR HARD DISK REMOVABLE CARTRIDGE DRIVES
+	CP	DIODEV_PPA		; PPA (ZIP DRIVE) IS REMOVABLE
+	JR	Z,DRV_INIT3B		; IF SO, SKIP MEDIA CHECK
+	CP	DIODEV_IMM		; IMM (ZIP DRIVE) IS REMOVABLE
+	JR	Z,DRV_INIT3B		; IF SO, SKIP MEDIA CHECK
+	CP	DIODEV_SYQ		; IMM (ZIP DRIVE) IS REMOVABLE
+	JR	Z,DRV_INIT3B		; IF SO, SKIP MEDIA CHECK
+
 	; CHECK FOR ACTIVE AND RETURN IF NOT
 	PUSH	DE			; SAVE DE (HARD DISK VOLUME COUNTER)
 	PUSH	HL			; SAVE DRIVE LIST PTR
@@ -2944,6 +2952,7 @@ DRV_INIT3A:
 
 	RET	NZ			; IF NO MEDIA, JUST RETURN
 
+DRV_INIT3B:
 	; IF ACTIVE...
 	LD	(HL),C			; SAVE UNIT NUM IN LIST
 	INC	HL			; BUMP PTR
@@ -3392,9 +3401,9 @@ DEV06	.DB	"SD$"
 DEV07	.DB	"PRPSD$"
 DEV08	.DB	"PPPSD$"
 DEV09	.DB	"HDSK$"
-DEV10	.EQU	DEVUNK
-DEV11	.EQU	DEVUNK
-DEV12	.EQU	DEVUNK
+DEV10	.DB	"PPA$"
+DEV11	.DB	"IMM$"
+DEV12	.DB	"SYQ$"
 DEV13	.EQU	DEVUNK
 DEV14	.EQU	DEVUNK
 DEV15	.EQU	DEVUNK

Source/CPM3/boot.z80

@@ -181,6 +181,14 @@ dinit3:
 	ret
 ;
 dinit3a:
+	; check for hard disk removable cartridge drives
+	cp	0A0h			; ppa (zip drive) is removable
+	jr	z,dinit3b		; if so, skip media check
+	cp	0B0h			; imm (zip drive) is removable
+	jr	z,dinit3b		; if so, skip media check
+	cp	0C0h			; syq (syquest drive) is removable
+	jr	z,dinit3b		; if so, skip media check
+
 	; check for active and return if not
 	push	de			; save de (hard disk volume counter)
 	push	hl			; save drive list ptr
@@ -195,7 +203,8 @@ dinit3a:
 	pop	de			; restore de
 	
 	ret	nz			; if no media, just return
-	
+
+dinit3b:
 	; if active...
 	ld	(hl),c			; save unit num in list
 	inc	hl			; bump ptr

Source/Doc/Applications.md

@@ -889,6 +889,28 @@ written in C and requires SDCC to compile. As such it is not part of
 the RomWBW build process. However, the full project and source code is
 found in the [FAT GitHub Repository](https://github.com/wwarthen/FAT).
 
+## Known Issues
+
+CP/M (and workalike) OSes have significant restrictions on filename
+characters.  The FAT application will block any attempt to create a
+file on the CP/M filesystem containing any of these prohibited
+characters:
+
+|         `< > . , ; : = ? * [ ] _ % | ( ) / \`
+
+The operation will be aborted with "`Error: Invalid Path Name`" if such
+a filename character is encountered.
+
+Since MS-DOS does allow some of these characters, you can have
+issues when copying files from MS-DOS to CP/M if the MS-DOS filenames
+use these characters.  Unfortunately, FAT is not yet smart enough to
+substitute illegal characters with legal ones.  So, you will need to
+clean the filenames before trying to copy them to CP/M.
+
+The FAT application does try to detect the scenario where you are
+copying a file to itself.  However, this detection is not perfect and
+can corrupt a file if it occurs.  Be careful to avoid this.
+
 `\clearpage`{=latex}
 
 # TUNE

Source/Doc/UserGuide.md

@@ -3896,10 +3896,12 @@ may be discovered by RomWBW in your system.
 | DSKY      | System   | Keypad & Display                                       |
 | DSRTC     | RTC      | Maxim DS1302 Real-Time Clock w/ NVRAM                  |
 | DUART     | Char     | SCC2681 or compatible Dual UART                        |
-| FD        | Disk     | 8272 of compatible Floppy Disk Controller              |
+| EMM       | Disk     | Disk drive on Parallel Port emm interface (Zip Drive)  |
+| FD        | Disk     | 8272 or compatible Floppy Disk Controller              |
 | GDC       | Video    | uPD7220 Video Display Controller                       |
 | HDSK      | Disk     | SIMH Simulator Hard Disk                               |
 | IDE       | Disk     | IDE/ATA Hard Disk Interface                            |
+| IMM       | Disk     | IMM Zip Drive on PPI                                   |
 | INTRTC    | RTC      | Interrupt-based Real Time Clock                        |
 | KBD       | Kbd      | 8242 PS/2 Keyboard Controller                          |
 | KIO       | System   | Zilog Serial/ Parallel Counter/Timer                   |
@@ -3909,6 +3911,7 @@ may be discovered by RomWBW in your system.
 | I2C       | System   | I2C Interface                                          |
 | PIO       | Char     | Zilog Parallel Interface Controller                    |
 | PPIDE     | Disk     | 8255 IDE/ATA Hard Disk Interface                       |
+| PPA       | Disk     | PPA Zip Drive on PPI                                   |
 | PPK       | Kbd      | Matrix Keyboard                                        |
 | PPPSD     | Disk     | ParPortProp SD Card Interface                          |
 | PPPCON    | Serial   | ParPortProp Serial Console Interface                   |
@@ -3921,6 +3924,7 @@ may be discovered by RomWBW in your system.
 | SIO       | Char     | Zilog Serial Port Interface                            |
 | SN76489   | Sound    | SN76489 Programmable Sound Generator                   |
 | SPK       | Sound    | Bit-bang Speaker                                       |
+| SYQ       | Disk     | Iomega SparQ Drive on PPI                              |
 | TMS       | Video    | TMS9918/38/58 Video Display Controller                 |
 | UART      | Char     | 16C550 Family Serial Interface                         |
 | USB-FIFO  | Char     | FT232H-based ECB USB FIFO                              |

Source/HBIOS/Config/RCZ80_easy.asm

@@ -75,5 +75,6 @@ IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
 SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
+IMMENABLE	.SET	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
 ;
 PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)

Source/HBIOS/Config/RCZ80_kio.asm

@@ -72,5 +72,6 @@ IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
 SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
+IMMENABLE	.SET	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
 ;
 PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)

Source/HBIOS/Config/RCZ80_skz.asm

@@ -67,5 +67,6 @@ IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
 SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
+IMMENABLE	.SET	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
 ;
 PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)

Source/HBIOS/Config/RCZ80_std.asm

@@ -61,5 +61,6 @@ PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
 SDMODE		.SET	SDMODE_PIO	; SD: DRIVER MODE: SDMODE_[JUHA|N8|CSIO|PPI|UART|DSD|MK4|SC|MT|PIO|USR]
 SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
+IMMENABLE	.SET	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
 ;
 PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)

Source/HBIOS/Config/RCZ80_tiny.asm

@@ -82,5 +82,6 @@ IDE0BASE	.SET	$90		; IDE 0: IO BASE ADDRESS
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
 SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
+IMMENABLE	.SET	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
 ;
 PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)

Source/HBIOS/Config/RCZ80_zrc.asm

@@ -59,5 +59,6 @@ IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
 SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
+IMMENABLE	.SET	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
 ;
 PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)

Source/HBIOS/Config/RCZ80_zrc_ram.asm

@@ -63,5 +63,6 @@ IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
 SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
+IMMENABLE	.SET	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
 ;
 PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)

Source/HBIOS/cfg_dyno.asm

@@ -252,6 +252,12 @@ PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)
 PIO_SBC		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR 8255 CHIP

Source/HBIOS/cfg_master.asm

@@ -311,12 +311,33 @@ PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
 PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
-LPTMODE		.EQU	LPTMODE_NONE	; LPT: DRIVER MODE: LPTMODE_[NONE|IBM|MG014]
+LPTMODE		.EQU	LPTMODE_NONE	; LPT: DRIVER MODE: LPTMODE_[NONE|SPP|MG014]
 LPTCNT		.EQU	1		; LPT: NUMBER OF CHIPS TO DETECT (1-2)
 LPTTRACE	.EQU	1		; LPT: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 LPT0BASE	.EQU	$E8		; LPT 0: REGISTERS BASE ADR
 LPT1BASE	.EQU	$EC		; LPT 1: REGISTERS BASE ADR
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+PPACNT		.EQU	1		; PPA: NUMBER OF PPA DEVICES (1-2)
+PPATRACE	.EQU	1		; PPA: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+PPAMODE		.EQU	PPAMODE_SPP	; PPA: DRIVER MODE: PPAMODE_[NONE|SPP|MG014]
+PPA0BASE	.EQU	LPT0BASE	; PPA 0: BASE I/O ADDRESS OF PPI FOR PPA
+PPA1BASE	.EQU	LPT1BASE	; PPA 1: BASE I/O ADDRESS OF PPI FOR PPA
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+IMMCNT		.EQU	1		; IMM: NUMBER OF IMM DEVICES (1-2)
+IMMTRACE	.EQU	1		; IMM: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+IMMMODE		.EQU	IMMMODE_SPP	; IMM: DRIVER MODE: IMMMODE_[NONE|SPP|MG014]
+IMM0BASE	.EQU	LPT0BASE	; IMM 0: BASE I/O ADDRESS OF PPI FOR IMM
+IMM1BASE	.EQU	LPT1BASE	; IMM 1: BASE I/O ADDRESS OF PPI FOR IMM
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+SYQCNT		.EQU	1		; SYQ: NUMBER OF SYQ DEVICES (1-2)
+SYQTRACE	.EQU	1		; SYQ: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+SYQMODE		.EQU	IMMMODE_SPP	; SYQ: DRIVER MODE: SYQMODE_[NONE|SPP|MG014]
+SYQ0BASE	.EQU	LPT0BASE	; SYQ 0: BASE I/O ADDRESS OF PPI FOR SYQ
+SYQ1BASE	.EQU	LPT1BASE	; SYQ 1: BASE I/O ADDRESS OF PPI FOR SYQ
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO4BASE	.EQU	$90		; PIO: PIO REGISTERS BASE ADR FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)

Source/HBIOS/cfg_mbc.asm

@@ -235,12 +235,33 @@ PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
 PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
-LPTMODE		.EQU	LPTMODE_IBM	; LPT: DRIVER MODE: LPTMODE_[NONE|IBM|MG014]
+LPTMODE		.EQU	LPTMODE_SPP	; LPT: DRIVER MODE: LPTMODE_[NONE|SPP|MG014]
 LPTCNT		.EQU	1		; LPT: NUMBER OF CHIPS TO DETECT (1-2)
 LPTTRACE	.EQU	1		; LPT: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 LPT0BASE	.EQU	$E8		; LPT 0: REGISTERS BASE ADR
 LPT1BASE	.EQU	$EC		; LPT 1: REGISTERS BASE ADR
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+PPACNT		.EQU	1		; PPA: NUMBER OF PPA DEVICES (1-2)
+PPATRACE	.EQU	1		; PPA: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+PPAMODE		.EQU	PPAMODE_SPP	; PPA: DRIVER MODE: PPAMODE_[NONE|MG014]
+PPA0BASE	.EQU	LPT0BASE	; PPA 0: BASE I/O ADDRESS OF PPI FOR PPA
+PPA1BASE	.EQU	LPT1BASE	; PPA 1: BASE I/O ADDRESS OF PPI FOR PPA
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+IMMCNT		.EQU	1		; IMM: NUMBER OF IMM DEVICES (1-2)
+IMMTRACE	.EQU	1		; IMM: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+IMMMODE		.EQU	IMMMODE_SPP	; IMM: DRIVER MODE: IMMMODE_[NONE|SPP|MG014]
+IMM0BASE	.EQU	LPT0BASE	; IMM 0: BASE I/O ADDRESS OF PPI FOR IMM
+IMM1BASE	.EQU	LPT1BASE	; IMM 1: BASE I/O ADDRESS OF PPI FOR IMM
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+SYQCNT		.EQU	1		; SYQ: NUMBER OF SYQ DEVICES (1-2)
+SYQTRACE	.EQU	1		; SYQ: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+SYQMODE		.EQU	IMMMODE_SPP	; SYQ: DRIVER MODE: SYQMODE_[NONE|SPP|MG014]
+SYQ0BASE	.EQU	LPT0BASE	; SYQ 0: BASE I/O ADDRESS OF PPI FOR SYQ
+SYQ1BASE	.EQU	LPT1BASE	; SYQ 1: BASE I/O ADDRESS OF PPI FOR SYQ
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO4BASE	.EQU	$90		; PIO: PIO REGISTERS BASE ADR FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)

Source/HBIOS/cfg_mk4.asm

@@ -248,12 +248,18 @@ PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
 PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
-LPTMODE		.EQU	LPTMODE_NONE	; LPT: DRIVER MODE: LPTMODE_[NONE|IBM|MG014]
+LPTMODE		.EQU	LPTMODE_NONE	; LPT: DRIVER MODE: LPTMODE_[NONE|SPP|MG014]
 LPTCNT		.EQU	1		; LPT: NUMBER OF CHIPS TO DETECT (1-2)
 LPTTRACE	.EQU	1		; LPT: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 LPT0BASE	.EQU	$E8		; LPT 0: REGISTERS BASE ADR
 LPT1BASE	.EQU	$EC		; LPT 1: REGISTERS BASE ADR
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO4BASE	.EQU	$90		; PIO: PIO REGISTERS BASE ADR FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)

Source/HBIOS/cfg_n8.asm

@@ -247,6 +247,12 @@ PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO4BASE	.EQU	$90		; PIO: PIO REGISTERS BASE ADR FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)

Source/HBIOS/cfg_rcz180.asm

@@ -257,12 +257,33 @@ PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
 PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
-LPTMODE		.EQU	LPTMODE_MG014	; LPT: DRIVER MODE: LPTMODE_[NONE|IBM|MG014]
+LPTMODE		.EQU	LPTMODE_MG014	; LPT: DRIVER MODE: LPTMODE_[NONE|SPP|MG014]
 LPTCNT		.EQU	1		; LPT: NUMBER OF CHIPS TO DETECT (1-2)
 LPTTRACE	.EQU	1		; LPT: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 LPT0BASE	.EQU	$18		; LPT 0: REGISTERS BASE ADR
 LPT1BASE	.EQU	$00		; LPT 1: REGISTERS BASE ADR
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+PPACNT		.EQU	1		; PPA: NUMBER OF PPA DEVICES (1-2)
+PPATRACE	.EQU	1		; PPA: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+PPAMODE		.EQU	PPAMODE_MG014	; PPA: DRIVER MODE: PPAMODE_[NONE|SPP|MG014]
+PPA0BASE	.EQU	LPT0BASE	; PPA 0: BASE I/O ADDRESS OF PPI FOR PPA
+PPA1BASE	.EQU	LPT1BASE	; PPA 1: BASE I/O ADDRESS OF PPI FOR PPA
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+IMMCNT		.EQU	1		; IMM: NUMBER OF IMM DEVICES (1-2)
+IMMTRACE	.EQU	1		; IMM: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+IMMMODE		.EQU	IMMMODE_MG014	; IMM: DRIVER MODE: IMMMODE_[NONE|SPP|MG014]
+IMM0BASE	.EQU	LPT0BASE	; IMM 0: BASE I/O ADDRESS OF PPI FOR IMM
+IMM1BASE	.EQU	LPT1BASE	; IMM 1: BASE I/O ADDRESS OF PPI FOR IMM
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+SYQCNT		.EQU	1		; SYQ: NUMBER OF SYQ DEVICES (1-2)
+SYQTRACE	.EQU	1		; SYQ: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+SYQMODE		.EQU	IMMMODE_MG014	; SYQ: DRIVER MODE: SYQMODE_[NONE|SPP|MG014]
+SYQ0BASE	.EQU	LPT0BASE	; SYQ 0: BASE I/O ADDRESS OF PPI FOR SYQ
+SYQ1BASE	.EQU	LPT1BASE	; SYQ 1: BASE I/O ADDRESS OF PPI FOR SYQ
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)
 PIO_SBC		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR 8255 CHIP

Source/HBIOS/cfg_rcz280.asm

@@ -261,12 +261,33 @@ PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
 PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
-LPTMODE		.EQU	LPTMODE_MG014	; LPT: DRIVER MODE: LPTMODE_[NONE|IBM|MG014]
+LPTMODE		.EQU	LPTMODE_MG014	; LPT: DRIVER MODE: LPTMODE_[NONE|SPP|MG014]
 LPTCNT		.EQU	1		; LPT: NUMBER OF CHIPS TO DETECT (1-2)
 LPTTRACE	.EQU	1		; LPT: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 LPT0BASE	.EQU	$18		; LPT 0: REGISTERS BASE ADR
 LPT1BASE	.EQU	$00		; LPT 1: REGISTERS BASE ADR
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+PPACNT		.EQU	1		; PPA: NUMBER OF PPA DEVICES (1-2)
+PPATRACE	.EQU	1		; PPA: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+PPAMODE		.EQU	PPAMODE_MG014	; PPA: DRIVER MODE: PPAMODE_[NONE|SPP|MG014]
+PPA0BASE	.EQU	LPT0BASE	; PPA 0: BASE I/O ADDRESS OF PPI FOR PPA
+PPA1BASE	.EQU	LPT1BASE	; PPA 1: BASE I/O ADDRESS OF PPI FOR PPA
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+IMMCNT		.EQU	1		; IMM: NUMBER OF IMM DEVICES (1-2)
+IMMTRACE	.EQU	1		; IMM: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+IMMMODE		.EQU	IMMMODE_MG014	; IMM: DRIVER MODE: IMMMODE_[NONE|SPP|MG014]
+IMM0BASE	.EQU	LPT0BASE	; IMM 0: BASE I/O ADDRESS OF PPI FOR IMM
+IMM1BASE	.EQU	LPT1BASE	; IMM 1: BASE I/O ADDRESS OF PPI FOR IMM
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+SYQCNT		.EQU	1		; SYQ: NUMBER OF SYQ DEVICES (1-2)
+SYQTRACE	.EQU	1		; SYQ: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+SYQMODE		.EQU	IMMMODE_MG014	; SYQ: DRIVER MODE: SYQMODE_[NONE|SPP|MG014]
+SYQ0BASE	.EQU	LPT0BASE	; SYQ 0: BASE I/O ADDRESS OF PPI FOR SYQ
+SYQ1BASE	.EQU	LPT1BASE	; SYQ 1: BASE I/O ADDRESS OF PPI FOR SYQ
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)
 PIO_SBC		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR 8255 CHIP

Source/HBIOS/cfg_rcz80.asm

@@ -255,12 +255,33 @@ PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
 PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
-LPTMODE		.EQU	LPTMODE_MG014	; LPT: DRIVER MODE: LPTMODE_[NONE|IBM|MG014]
+LPTMODE		.EQU	LPTMODE_MG014	; LPT: DRIVER MODE: LPTMODE_[NONE|SPP|MG014]
 LPTCNT		.EQU	1		; LPT: NUMBER OF CHIPS TO DETECT (1-2)
 LPTTRACE	.EQU	1		; LPT: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
-LPT0BASE	.EQU	$18		; LPT 0: REGISTERS BASE ADR
+LPT0BASE	.EQU	$0C		; LPT 0: REGISTERS BASE ADR
 LPT1BASE	.EQU	$00		; LPT 1: REGISTERS BASE ADR
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+PPACNT		.EQU	1		; PPA: NUMBER OF PPA DEVICES (1-2)
+PPATRACE	.EQU	1		; PPA: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+PPAMODE		.EQU	PPAMODE_MG014	; PPA: DRIVER MODE: PPAMODE_[NONE|SPP|MG014]
+PPA0BASE	.EQU	LPT0BASE	; PPA 0: BASE I/O ADDRESS OF PPI FOR PPA
+PPA1BASE	.EQU	LPT1BASE	; PPA 1: BASE I/O ADDRESS OF PPI FOR PPA
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+IMMCNT		.EQU	1		; IMM: NUMBER OF IMM DEVICES (1-2)
+IMMTRACE	.EQU	1		; IMM: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+IMMMODE		.EQU	IMMMODE_MG014	; IMM: DRIVER MODE: IMMMODE_[NONE|SPP|MG014]
+IMM0BASE	.EQU	LPT0BASE	; IMM 0: BASE I/O ADDRESS OF PPI FOR IMM
+IMM1BASE	.EQU	LPT1BASE	; IMM 1: BASE I/O ADDRESS OF PPI FOR IMM
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+SYQCNT		.EQU	1		; SYQ: NUMBER OF SYQ DEVICES (1-2)
+SYQTRACE	.EQU	1		; SYQ: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+SYQMODE		.EQU	IMMMODE_MG014	; SYQ: DRIVER MODE: SYQMODE_[NONE|SPP|MG014]
+SYQ0BASE	.EQU	LPT0BASE	; SYQ 0: BASE I/O ADDRESS OF PPI FOR SYQ
+SYQ1BASE	.EQU	LPT1BASE	; SYQ 1: BASE I/O ADDRESS OF PPI FOR SYQ
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)
 PIO_SBC		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR 8255 CHIP

Source/HBIOS/cfg_rph.asm

@@ -236,6 +236,12 @@ PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO4BASE	.EQU	$90		; PIO: PIO REGISTERS BASE ADR FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)

Source/HBIOS/cfg_sbc.asm

@@ -234,11 +234,12 @@ PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
 PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
-LPTMODE		.EQU	LPTMODE_NONE	; LPT: DRIVER MODE: LPTMODE_[NONE|IBM|MG014]
-LPTCNT		.EQU	1		; LPT: NUMBER OF CHIPS TO DETECT (1-2)
-LPTTRACE	.EQU	1		; LPT: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
-LPT0BASE	.EQU	$E8		; LPT 0: REGISTERS BASE ADR
-LPT1BASE	.EQU	$EC		; LPT 1: REGISTERS BASE ADR
+;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
 ;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO4BASE	.EQU	$90		; PIO: PIO REGISTERS BASE ADR FOR ECB 4P BOARD

Source/HBIOS/cfg_scz180.asm

@@ -251,12 +251,33 @@ PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
 PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
-LPTMODE		.EQU	LPTMODE_MG014	; LPT: DRIVER MODE: LPTMODE_[NONE|IBM|MG014]
+LPTMODE		.EQU	LPTMODE_MG014	; LPT: DRIVER MODE: LPTMODE_[NONE|SPP|MG014]
 LPTCNT		.EQU	1		; LPT: NUMBER OF CHIPS TO DETECT (1-2)
 LPTTRACE	.EQU	1		; LPT: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 LPT0BASE	.EQU	$18		; LPT 0: REGISTERS BASE ADR
 LPT1BASE	.EQU	$00		; LPT 1: REGISTERS BASE ADR
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+PPACNT		.EQU	1		; PPA: NUMBER OF PPA DEVICES (1-2)
+PPATRACE	.EQU	1		; PPA: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+PPAMODE		.EQU	PPAMODE_MG014	; PPA: DRIVER MODE: PPAMODE_[NONE|SPP|MG014]
+PPA0BASE	.EQU	LPT0BASE	; PPA 0: BASE I/O ADDRESS OF PPI FOR PPA
+PPA1BASE	.EQU	LPT1BASE	; PPA 1: BASE I/O ADDRESS OF PPI FOR PPA
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+IMMCNT		.EQU	1		; IMM: NUMBER OF IMM DEVICES (1-2)
+IMMTRACE	.EQU	1		; IMM: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+IMMMODE		.EQU	IMMMODE_MG014	; IMM: DRIVER MODE: IMMMODE_[NONE|SPP|MG014]
+IMM0BASE	.EQU	LPT0BASE	; IMM 0: BASE I/O ADDRESS OF PPI FOR IMM
+IMM1BASE	.EQU	LPT1BASE	; IMM 1: BASE I/O ADDRESS OF PPI FOR IMM
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+SYQCNT		.EQU	1		; SYQ: NUMBER OF SYQ DEVICES (1-2)
+SYQTRACE	.EQU	1		; SYQ: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+SYQMODE		.EQU	IMMMODE_MG014	; SYQ: DRIVER MODE: SYQMODE_[NONE|SPP|MG014]
+SYQ0BASE	.EQU	LPT0BASE	; SYQ 0: BASE I/O ADDRESS OF PPI FOR SYQ
+SYQ1BASE	.EQU	LPT1BASE	; SYQ 1: BASE I/O ADDRESS OF PPI FOR SYQ
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)
 PIO_SBC		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR 8255 CHIP

Source/HBIOS/cfg_z80retro.asm

@@ -206,6 +206,12 @@ PIOENABLE	.EQU	FALSE		; PIO: ENABLE ZILOG PIO DRIVER (PIO.ASM)
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)
 PIO_SBC		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR 8255 CHIP

Source/HBIOS/cfg_zeta.asm

@@ -177,6 +177,12 @@ PIOENABLE	.EQU	FALSE		; PIO: ENABLE ZILOG PIO DRIVER (PIO.ASM)
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)
 PIO_SBC		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR 8255 CHIP

Source/HBIOS/cfg_zeta2.asm

@@ -188,6 +188,12 @@ PIOENABLE	.EQU	FALSE		; PIO: ENABLE ZILOG PIO DRIVER (PIO.ASM)
 ;
 LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
 ;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+;
 PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)
 PIO_SBC		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR 8255 CHIP

Source/HBIOS/hbios.asm

@@ -1261,11 +1261,11 @@ Z280_INITZ:
 
 	; SET DEFAULT CPU CLOCK MULTIPLIERS (XTAL / 2)
 	;
-	; IT HAS BEEN REPORTED THAT CMR NEEDS TO BE SET PRIOR TO CCR
-	; WHEN USING AN INPUT FREQUENCY THAT IS XTAL / 2.
-	; I NEVER EXPERIENCED A PROBLEM RELATED TO ORDER, BUT JUST
+	; BILL MCMULLEN REPORTED THAT CMR NEEDS TO BE SET PRIOR TO CCR
+	; WHEN USING A CPU FREQUENCY (PHI) THAT IS XTAL * 2.
+	; HERE WE ARE SETTING CPU FREQUENCY TO XTAL / 2, BUT JUST
 	; FOR GOOD MEASURE, CMR IS SET PRIOR TO CCR BELOW.
-	; https://www.retrobrewcomputers.org/forum/index.php?t=msg&th=316&#msg_5045
+	; https://www.retrobrewcomputers.org/forum/index.php?t=msg&th=316&goto=5045&#msg_5045
 	XOR	A
 	OUT0	(Z180_CMR),A
 	OUT0	(Z180_CCR),A
@@ -3239,6 +3239,15 @@ HB_INITTBL:
 #IF (HDSKENABLE)
 	.DW	HDSK_INIT
 #ENDIF
+#IF (PPAENABLE)
+	.DW	PPA_INIT
+#ENDIF
+#IF (IMMENABLE)
+	.DW	IMM_INIT
+#ENDIF
+#IF (SYQENABLE)
+	.DW	SYQ_INIT
+#ENDIF
 #IF (PRPENABLE)
 	.DW	PRP_INIT
 #ENDIF
@@ -6348,6 +6357,33 @@ SIZ_HDSK	.EQU	$ - ORG_HDSK
 		.ECHO	" bytes.\n"
 #ENDIF
 ;
+#IF (PPAENABLE)
+ORG_PPA		.EQU	$
+  #INCLUDE "ppa.asm"
+SIZ_PPA		.EQU	$ - ORG_PPA
+		.ECHO	"PPA occupies "
+		.ECHO	SIZ_PPA
+		.ECHO	" bytes.\n"
+#ENDIF
+;
+#IF (IMMENABLE)
+ORG_IMM		.EQU	$
+  #INCLUDE "imm.asm"
+SIZ_IMM		.EQU	$ - ORG_IMM
+		.ECHO	"IMM occupies "
+		.ECHO	SIZ_IMM
+		.ECHO	" bytes.\n"
+#ENDIF
+;
+#IF (SYQENABLE)
+ORG_SYQ		.EQU	$
+  #INCLUDE "syq.asm"
+SIZ_SYQ		.EQU	$ - ORG_SYQ
+		.ECHO	"SYQ occupies "
+		.ECHO	SIZ_SYQ
+		.ECHO	" bytes.\n"
+#ENDIF
+;
 #IF (TERMENABLE)
 ORG_TERM	.EQU	$
   #INCLUDE "term.asm"
@@ -6762,7 +6798,6 @@ PS_PRTDC:
 	RES	7,D			; CLEAR LBA BIT
 	LD	B,11			; 11 BIT SHIFT TO CONVERT BLOCKS --> MB
 	CALL	SRL32			; RIGHT SHIFT
-	;CALL	PRTDEC			; PRINT LOW WORD IN DECIMAL (HIGH WORD DISCARDED)
 	CALL	PRTDEC32		; PRINT DWORD IN DECIMAL
 	PRTS("MB$")			; PRINT SUFFIX
 	CALL	PC_COMMA
@@ -6777,7 +6812,6 @@ PS_PRTDC1:
 	RES	7,D			; CLEAR LBA BIT
 	LD	B,1			; 11 BIT SHIFT TO CONVERT BLOCKS --> MB
 	CALL	SRL32			; RIGHT SHIFT
-	;CALL	PRTDEC			; PRINT LOW WORD IN DECIMAL (HIGH WORD DISCARDED)
 	CALL	PRTDEC32		; PRINT DWORD IN DECIMAL
 	PRTS("KB$")			; PRINT SUFFIX
 	CALL	PC_COMMA
@@ -7134,6 +7168,9 @@ PS_DDSD		.TEXT	"SD$"
 PS_DDPRPSD	.TEXT	"PRPSD$"
 PS_DDPPPSD	.TEXT	"PPPSD$"
 PS_DDHDSK	.TEXT	"HDSK$"
+PS_DDPPA	.TEXT	"PPA$"
+PS_DDIMM	.TEXT	"IMM$"
+PS_DDSYQ	.TEXT	"SYQ$"
 ;
 ; DISK TYPE STRINGS
 ;

Source/HBIOS/hbios.inc

@@ -321,6 +321,9 @@ DIODEV_SD	.EQU	$60
 DIODEV_PRPSD	.EQU	$70
 DIODEV_PPPSD	.EQU	$80
 DIODEV_HDSK	.EQU	$90
+DIODEV_PPA	.EQU	$A0
+DIODEV_IMM	.EQU	$B0
+DIODEV_SYQ	.EQU	$C0
 ;
 ; RTC DEVICE IDS
 ;

Source/HBIOS/lpt.asm

@@ -10,9 +10,10 @@
 ;
 ;==================================================================================================
 ;
-;  IBM STYLE INTERFACE (USED BY NHYODYNE PRINT MODULE):
+;  IBM PC STANDARD PARALLEL PORT (SPP):
+;  - NHYODYNE PRINT MODULE
 ;
-;  PORT 0 (INPUT/OUTPUT):
+;  PORT 0 (OUTPUT):
 ;
 ;	D7	D6	D5	D4	D3	D2	D1	D0
 ;     +-------+-------+-------+-------+-------+-------+-------+-------+
@@ -26,7 +27,7 @@
 ;     | /BUSY | /ACK  | POUT  | SEL   | /ERR  | 0     | 0     | 0     |
 ;     +-------+-------+-------+-------+-------+-------+-------+-------+
 ;
-;  PORT 2 (INPUT/OUTPUT):
+;  PORT 2 (OUTPUT):
 ;
 ;	D7	D6	D5	D4	D3	D2	D1	D0
 ;     +-------+-------+-------+-------+-------+-------+-------+-------+
@@ -35,9 +36,10 @@
 ;
 ;==================================================================================================
 ;
-;  MG014 STYLE INTERFACE (USED BY RCBUS MG014 MODULE):
+;  MG014 STYLE INTERFACE:
+;  - RCBUS MG014 MODULE
 ;
-;  PORT 0 (INPUT/OUTPUT):
+;  PORT 0 (OUTPUT):
 ;
 ;	D7	D6	D5	D4	D3	D2	D1	D0
 ;     +-------+-------+-------+-------+-------+-------+-------+-------+
@@ -51,7 +53,7 @@
 ;     |	      |	      |	      | /ERR  | SEL   | POUT  | BUSY  | /ACK  |
 ;     +-------+-------+-------+-------+-------+-------+-------+-------+
 ;
-;  PORT 2 (INPUT/OUTPUT):
+;  PORT 2 (OUTPUT):
 ;
 ;	D7	D6	D5	D4	D3	D2	D1	D0
 ;     +-------+-------+-------+-------+-------+-------+-------+-------+
@@ -165,7 +167,7 @@ LPT_OUT:
 	JR	Z,LPT_OUT		; LOOP IF NOT
 	LD	C,(IY+3)		; PORT 0 (DATA)
 	OUT	(C),E			; OUTPUT DATA TO PORT
-#IF (LPTMODE == LPTMODE_IBM)
+#IF (LPTMODE == LPTMODE_SPP)
 	LD	A,%00001101		; SELECT & STROBE, LEDS OFF
 #ENDIF
 #IF (LPTMODE == LPTMODE_MG014)
@@ -175,7 +177,7 @@ LPT_OUT:
 	INC	C
 	OUT	(C),A			; OUTPUT DATA TO PORT
 	CALL	DELAY
-#IF (LPTMODE == LPTMODE_IBM)
+#IF (LPTMODE == LPTMODE_SPP)
 	LD	A,%00001100		; SELECT, LEDS OFF
 #ENDIF
 #IF (LPTMODE == LPTMODE_MG014)
@@ -199,7 +201,7 @@ LPT_OST:
 	LD	C,(IY+3)		; BASE PORT
 	INC	C			; SELECT STATUS PORT
 	IN	A,(C)			; GET STATUS INFO
-#IF (LPTMODE == LPTMODE_IBM)
+#IF (LPTMODE == LPTMODE_SPP)
 	AND	%10000000		; ISOLATE /BUSY
 #ENDIF
 #IF (LPTMODE == LPTMODE_MG014)
@@ -221,7 +223,7 @@ LPT_INITDEV:
 ;
 LPT_INITDEVX:
 ;
-#IF (LPTMODE == LPTMODE_IBM)
+#IF (LPTMODE == LPTMODE_SPP)
 ;
 	LD	C,(IY+3)		; PORT 0 (DATA)
 	XOR	A			; CLEAR ACCUM
@@ -283,7 +285,7 @@ LPT_DETECT:
 ;
 #ENDIF
 ;
-#IF (LPTMODE == LPTMODE_IBM)
+#IF (LPTMODE == LPTMODE_SPP)
 ;
 LPT_DETECT:
 	LD	C,(IY+3)		; BASE PORT ADDRESS
@@ -294,7 +296,7 @@ LPT_DETECT:
 ;
 LPT_DETECT1:
 	; LPT FOUND, RECORD IT
-	LD	A,LPTMODE_IBM		; RETURN CHIP TYPE
+	LD	A,LPTMODE_SPP		; RETURN CHIP TYPE
 	RET				; DONE
 ;
 LPT_DETECT2:
@@ -372,7 +374,7 @@ LPT_PRTCFG:
 	CALL	PRTHEXBYTE		; PRINT BASE PORT
 
 	; PRINT THE LPT TYPE
-	CALL	PC_SPACE		; FORMATTING
+	PRTS(" MODE=$")			; FORMATTING
 	LD	A,(IY+1)		; GET LPT TYPE BYTE
 	RLCA				; MAKE IT A WORD OFFSET
 	LD	HL,LPT_TYPE_MAP		; POINT HL TO TYPE MAP TABLE
@@ -396,11 +398,11 @@ LPT_PRTCFG:
 ;
 LPT_TYPE_MAP:
 		.DW	LPT_STR_NONE
-		.DW	LPT_STR_IBM
+		.DW	LPT_STR_SPP
 		.DW	LPT_STR_MG014
 ;
 LPT_STR_NONE	.DB	"<NOT PRESENT>$"
-LPT_STR_IBM	.DB	"IBM$"
+LPT_STR_SPP	.DB	"SPP$"
 LPT_STR_MG014	.DB	"MG014$"
 ;
 ; WORKING VARIABLES

Source/HBIOS/ppp.asm

@@ -904,7 +904,7 @@ PPPSD_GETCSD:
 	CALL	PPP_SNDCMD		; SEND COMMAND
 	RET	NZ			; ABORT ON ERROR
 
-	LD	B,16			; GET 4 BYTES
+	LD	B,16			; GET 16 BYTES
 	LD	HL,PPPSD_CSDBUF
 PPPSD_GETCSD1:
 	CALL	PPP_GETBYTE

Source/HBIOS/romldr.asm

@@ -180,7 +180,7 @@ start1:
 	call	pstr			; do it
 	call	clrbuf			; zero fill the cmd buffer
 ;
-#if (BIOS == BIOS_WBW)
+#if ((BIOS == BIOS_WBW) & FPSW_ENABLE)
 ;
 	ld	b,BF_SYSGET		; HBIOS SysGet
 	ld	c,BF_SYSGET_PANEL	; ... Panel swiches value
@@ -390,7 +390,7 @@ runcmd2:
 	ld	(bootslice),a		; save boot slice
 	jp	diskboot		; boot the disk unit/slice
 ;
-#if (BIOS == BIOS_WBW)
+#if ((BIOS == BIOS_WBW) & FPSW_ENABLE)
 ;
 ;=======================================================================
 ; Process Front Panel switches

Source/HBIOS/std.asm

@@ -245,9 +245,27 @@ GDCMODE_RPH	.EQU	2		; RPH GDC
 ; LPT DRIVER MODE SELECTIONS
 ;
 LPTMODE_NONE	.EQU	0		; NONE
-LPTMODE_IBM	.EQU	1		; IBM STYLE INTERFACE
+LPTMODE_SPP	.EQU	1		; IBM PC STANDARD PAR PORT (SPP)
 LPTMODE_MG014	.EQU	2		; RCBUS MG014 STYLE INTERFACE
 ;
+; PPA DRIVER MODE SELECTIONS
+;
+PPAMODE_NONE	.EQU	0		; NONE
+PPAMODE_SPP	.EQU	1		; IBM PC STANDARD PAR PORT (SPP)
+PPAMODE_MG014	.EQU	2		; RCBUS MG014 STYLE INTERFACE
+;
+; IMM DRIVER MODE SELECTIONS
+;
+IMMMODE_NONE	.EQU	0		; NONE
+IMMMODE_SPP	.EQU	1		; IBM PC STANDARD PAR PORT (SPP)
+IMMMODE_MG014	.EQU	2		; RCBUS MG014 STYLE INTERFACE
+;
+; SYQ DRIVER MODE SELECTIONS
+;
+SYQMODE_NONE	.EQU	0		; NONE
+SYQMODE_SPP	.EQU	1		; IBM PC STANDARD PAR PORT (SPP)
+SYQMODE_MG014	.EQU	2		; RCBUS MG014 STYLE INTERFACE
+;
 ; GDC MONITOR SELECTIONS
 ;
 GDCMON_NONE	.EQU	0
@@ -437,6 +455,16 @@ SPD_UNSUP	.EQU	0		; PLATFORM CAN CHANGE SPEEDS BUT IS UNSUPPORTED
 SPD_HIGH	.EQU	1		; PLATFORM CAN CHANGE SPEED, STARTS HIGH
 SPD_LOW		.EQU	2		; PLATFORM CAN CHANGE SPEED, STARTS LOW
 ;
+; SCSI COMMAND CODES (SHOULD BE IT IT'S OWN FILE)
+;
+SCSI_CMD_READ	.EQU	$08
+SCSI_CMD_INQ	.EQU	$12
+SCSI_CMD_TEST	.EQU	$00
+SCSI_CMD_START	.EQU	$1B
+SCSI_CMD_SENSE	.EQU	$03
+SCSI_CMD_WRITE	.EQU	$0A
+SCSI_CMD_RDCAP	.EQU	$25
+;
 #INCLUDE "build.inc"		; INCLUDE USER CONFIG, ADD VARIANT, TIMESTAMP, & ROMSIZE
 ;
 ; INCLUDE Z180 REGISTER DEFINITIONS

Source/pSys/ReadMe.txt

@@ -48,7 +48,7 @@ The layout of the first track does not conform exactly to the
 recommended p-System layout.  The recommended layout is not possible 
 because it conflicts with the RomWBW definition for a boot track.  
 However, the changes are only slightly different sector assignments for 
-the different boot componets -- the general boot sequence and mechanism 
+the different boot components -- the general boot sequence and mechanism 
 for the p-System is completely standard.
 
 The logical disk geometry used by this p-System
@@ -77,14 +77,17 @@ escape sequence handling configuration.  The debugger code as added to
 SYSTEM.PASCAL to enable the debug function.  SYSTEM.INTERP was modified 
 to enable the extended BIOS functions.
 
-The build/makefile creates the psys disk image (psys.img) by adding 
-concatentating psys.vol and blank.vol (after adding track 0 contents to 
+The build/makefile creates the psys disk image (psys.img) by 
+concatenating psys.vol and blank.vol (after adding track 0 contents to 
 each).  psys.vol and blank.vol are recognized by CiderPress and 
 CiderPress can be used to add/remove files from these volumes.  
-However, there is currently no straightforward way to extract the 
-volumes from the disk image.  If you are good with a binary disk 
-editor, you can do it that way.  Please contact me if you are 
-interested in pursuing that.
+To extract volumes from a disk image, Andrew Davidson has created
+a nice Python script that can extract p-System volumes from an
+existing disk image file.  The extracted volume can be manipulated
+by CiderPress.  The script is also capable of re-inserting a modified
+volume back into the disk image file.  This tool is available at:
+https://github.com/robosnacks/psysimg.
+
 
 There is currently no support for floppy drives.
 
@@ -119,7 +122,7 @@ that SofTech produced a IV.1 with some nice enhancements (like
 subsidiary volumes and decent support for ANSI/VT-100 terminals).  I
 have been unable to track down the IV.1 distribution media despite
 trying very hard.  If anyone knows of a source for the media of the
-Adapable p-System for Z80, I would love to get hold of it.
+Adaptable p-System for Z80, I would love to get hold of it.
 
 3:58 PM Tuesday, January 17, 2023
 
@@ -138,4 +141,10 @@ arrow keys transmitted by an ANSI/VT-100 terminal.  In this case,
 the setup program was used to define up/down/left/right like
 WordStar does: ^E,^X,^S,^D.
 
-5:48 PM Tuesday, January 17, 2023
+5:48 PM Tuesday, January 17, 2023
+
+Updated instructions above to include a reference to Andrew 
+Davidson's Python script that will extract/insert volumes from/to
+a disk image.
+
+1:31 PM Thursday, May 11, 2023

Source/ver.inc

@@ -2,7 +2,7 @@
 #DEFINE	RMN	3
 #DEFINE	RUP	0
 #DEFINE	RTP	0
-#DEFINE BIOSVER	"3.3.0-dev.13"
+#DEFINE BIOSVER	"3.3.0-dev.20"
 #define rmj	RMJ
 #define rmn	RMN
 #define rup	RUP

Source/ver.lib

@@ -3,5 +3,5 @@ rmn	equ	3
 rup	equ	0
 rtp	equ	0
 biosver	macro
-	db	"3.3.0-dev.13"
+	db	"3.3.0-dev.20"
 	endm