Revise S100 Monitor Boot Option

- PIO mode of sd.asm driver modified to setup shadow register (Issue #352).
- Relocated Z280 IVT to improve space utilization in HBIOS bank.

Doc/ChangeLog.txt

@@ -16,6 +16,7 @@ Version 3.3
 - WBW: Support for Z180 running interrupt mode 1
 - WBW: Preliminary support for S100 Computers Z180
 - WBW: Preliminary support for Dan Werner's ESP32 MBC Module
+- WBW: Early support for Duodyne base system (CPU/UART/ROM/RAM/RTC/SPK)
 
 Version 3.2.1
 -------------

Source/Apps/rtc.asm

@@ -51,7 +51,7 @@ PORT_DYNO	.EQU	$0C		; RTC port for DYNO
 PORT_RCZ280	.EQU	$C0		; RTC port for RCZ280
 PORT_MBC	.EQU	$70		; RTC port for MBC
 PORT_RPH	.EQU	$84		; RTC port for RHYOPHYRE
-PORT_DUO	.EQU	$70		; RTC port for DUODYNE
+PORT_DUO	.EQU	$94		; RTC port for DUODYNE
 
 
 BDOS		.EQU	5		; BDOS invocation vector
@@ -1140,7 +1140,7 @@ HINIT:
 ;
 	LD	C,PORT_DUO
 	LD	DE,PLT_DUO
-	CP	13		; DUODYNE
+	CP	17		; DUODYNE
 	JP	Z,RTC_INIT2
 ;
 	; Unknown platform

Source/HBIOS/Config/DUO_std.asm

@@ -33,26 +33,12 @@ INTMODE		.SET	0		; INTERRUPTS: 0=NONE, 1=MODE 1, 2=MODE 2, 3=MODE 3 (Z280)
 ;
 DMAENABLE	.SET	FALSE		; DMA: ENABLE DMA DRIVER (DMA.ASM)
 ;
-BATCOND		.SET	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
-;
-CPUSPDDEF	.SET	SPD_LOW		; CPU SPEED DEFAULT SPD_UNSUP|SPD_HIGH|SPD_LOW
+BATCOND		.SET	TRUE		; ENABLE LOW BATTERY WARNING MESSAGE
 ;
 ROMSIZE		.SET	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
 RAMSIZE		.SET	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ;
 MDFFENABLE	.SET	FALSE		; MD: ENABLE FLASH FILE SYSTEM
 ;
-DSKYENABLE	.SET	TRUE		; ENABLES DSKY FUNCTIONALITY
-ICMENABLE	.SET	FALSE		; ENABLES ORIGINAL DSKY ICM DRIVER (7218)
-PKDENABLE	.SET	TRUE		; ENABLES DSKY NG PKD DRIVER (8259)
-;
 UARTINTS	.SET	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 ;UARTCFG	.SET	UARTCFG | SER_RTS
-;
-LPTENABLE	.SET	TRUE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
-;
-CVDUMON		.SET	CVDUMON_CGA	; CVDU: CVDU MONITOR SETUP: CVDUMON_[NONE|CGA|EGA]
-;
-FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-;
-PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/RCZ280_zz80mb.asm

@@ -28,7 +28,7 @@
 ;
 #include "cfg_rcz280.asm"
 ;
-CPUOSC		.SET	12000000	; CPU OSC FREQ IN MHZ
+CPUOSC		.SET	24000000	; CPU OSC FREQ IN MHZ
 INTMODE		.SET	3		; INTERRUPTS: 0=NONE, 1=MODE 1, 2=MODE 2
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
 ;

Source/HBIOS/cfg_duo.asm

@@ -26,8 +26,8 @@ TICKFREQ	.EQU	50		; DESIRED PERIODIC TIMER INTERRUPT FREQUENCY (HZ)
 BOOT_TIMEOUT	.EQU	-1		; AUTO BOOT TIMEOUT IN SECONDS, -1 TO DISABLE, 0 FOR IMMEDIATE
 BOOT_DELAY	.EQU	0		; FIXED BOOT DELAY IN SECONDS PRIOR TO CONSOLE OUTPUT
 ;
-CPUSPDCAP	.EQU	SPD_HILO	; CPU SPEED CHANGE CAPABILITY SPD_FIXED|SPD_HILO
-CPUSPDDEF	.EQU	SPD_LOW		; CPU SPEED DEFAULT SPD_UNSUP|SPD_HIGH|SPD_LOW
+CPUSPDCAP	.EQU	SPD_FIXED	; CPU SPEED CHANGE CAPABILITY SPD_FIXED|SPD_HILO
+CPUSPDDEF	.EQU	SPD_UNSUP	; CPU SPEED DEFAULT SPD_UNSUP|SPD_HIGH|SPD_LOW
 CPUOSC		.EQU	8000000		; CPU OSC FREQ IN MHZ
 INTMODE		.EQU	0		; INTERRUPTS: 0=NONE, 1=MODE 1, 2=MODE 2, 3=MODE 3 (Z280)
 DEFSERCFG	.EQU	SER_38400_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
@@ -36,18 +36,18 @@ RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE_CHK	.EQU	0		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
 MEMMGR		.EQU	MM_Z2		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
-MPGSEL_0	.EQU	$78		; Z2 MEM MGR BANK 0 PAGE SELECT REG (WRITE ONLY)
-MPGSEL_1	.EQU	$79		; Z2 MEM MGR BANK 1 PAGE SELECT REG (WRITE ONLY)
-MPGSEL_2	.EQU	$7A		; Z2 MEM MGR BANK 2 PAGE SELECT REG (WRITE ONLY)
-MPGSEL_3	.EQU	$7B		; Z2 MEM MGR BANK 3 PAGE SELECT REG (WRITE ONLY)
-MPGENA		.EQU	$7C		; Z2 MEM MGR PAGING ENABLE REGISTER (BIT 0, WRITE ONLY)
+MPGSEL_0	.EQU	$50		; Z2 MEM MGR BANK 0 PAGE SELECT REG (WRITE ONLY)
+MPGSEL_1	.EQU	$51		; Z2 MEM MGR BANK 1 PAGE SELECT REG (WRITE ONLY)
+MPGSEL_2	.EQU	$52		; Z2 MEM MGR BANK 2 PAGE SELECT REG (WRITE ONLY)
+MPGSEL_3	.EQU	$53		; Z2 MEM MGR BANK 3 PAGE SELECT REG (WRITE ONLY)
+MPGENA		.EQU	$54		; Z2 MEM MGR PAGING ENABLE REGISTER (BIT 0, WRITE ONLY)
 ;
-RTCIO		.EQU	$70		; RTC LATCH REGISTER ADR
+RTCIO		.EQU	$94		; RTC LATCH REGISTER ADR
 ;
 KIOENABLE	.EQU	FALSE		; ENABLE ZILOG KIO SUPPORT
 KIOBASE		.EQU	$80		; KIO BASE I/O ADDRESS
 ;
-CTCENABLE	.EQU	TRUE		; ENABLE ZILOG CTC SUPPORT
+CTCENABLE	.EQU	FALSE		; ENABLE ZILOG CTC SUPPORT
 CTCDEBUG	.EQU	FALSE		; ENABLE CTC DRIVER DEBUG OUTPUT
 CTCBASE		.EQU	$B0		; CTC BASE I/O ADDRESS
 CTCTIMER	.EQU	TRUE		; ENABLE CTC PERIODIC TIMER
@@ -65,7 +65,7 @@ WDOGMODE	.EQU	WDOG_NONE	; WATCHDOG MODE: WDOG_[NONE|EZZ80|SKZ]
 ;
 FPLED_ENABLE	.EQU	FALSE		; FP: ENABLES FRONT PANEL LEDS
 FPLED_IO	.EQU	$00		; FP: PORT ADDRESS FOR FP LEDS
-FPLED_DSKACT	.EQU	TRUE		; FP: ENABLES DISK I/O ACTIVITY ON FP LEDS
+FPLED_DSKACT	.EQU	FALSE		; FP: ENABLES DISK I/O ACTIVITY ON FP LEDS
 FPSW_ENABLE	.EQU	FALSE		; FP: ENABLES FRONT PANEL SWITCHES
 FPSW_IO		.EQU	$00		; FP: PORT ADDRESS FOR FP SWITCHES
 ;
@@ -123,13 +123,14 @@ UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG	; UART: LINE CONFIG FOR UART PORTS
 UARTCASSPD	.EQU	SER_300_8N1	; UART: ECB CASSETTE UART DEFAULT SPEED
-UARTSBC		.EQU	TRUE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
 UARTSBCFORCE	.EQU	FALSE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
 UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
-UARTDUAL	.EQU	TRUE		; UART: AUTO-DETECT DUAL UART
+UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
+UARTDUO		.EQU	TRUE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;
@@ -137,7 +138,7 @@ Z2UENABLE	.EQU	FALSE		; Z2U: ENABLE Z280 UART SERIAL DRIVER (Z2U.ASM)
 ;
 ACIAENABLE	.EQU	FALSE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
 ;
-SIOENABLE	.EQU	TRUE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
+SIOENABLE	.EQU	FALSE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
 SIODEBUG	.EQU	FALSE		; SIO: ENABLE DEBUG OUTPUT
 SIOBOOT		.EQU	0		; SIO: REBOOT ON RCV CHAR (0=DISABLED)
 SIOCNT		.EQU	1		; SIO: NUMBER OF CHIPS TO DETECT (1-2), 2 CHANNELS PER CHIP
@@ -154,11 +155,11 @@ XIOCFG		.EQU	DEFSERCFG	; XIO: SERIAL LINE CONFIG
 ;
 VDUENABLE	.EQU	FALSE		; VDU: ENABLE VDU VIDEO/KBD DRIVER (VDU.ASM)
 VDUSIZ		.EQU	V80X25		; VDU: DISPLAY FORMAT [V80X24|V80X25|V80X30]
-CVDUENABLE	.EQU	TRUE		; CVDU: ENABLE CVDU VIDEO/KBD DRIVER (CVDU.ASM)
+CVDUENABLE	.EQU	FALSE		; CVDU: ENABLE CVDU VIDEO/KBD DRIVER (CVDU.ASM)
 CVDUMODE	.EQU	CVDUMODE_MBC	; CVDU: CVDU MODE: CVDUMODE_[NONE|ECB|MBC]
 CVDUMON		.EQU	CVDUMON_CGA	; CVDU: CVDU MONITOR SETUP: CVDUMON_[NONE|CGA|EGA]
 GDCENABLE	.EQU	FALSE		; GDC: ENABLE 7220 GDC VIDEO/KBD DRIVER (GDC.ASM)
-TMSENABLE	.EQU	TRUE		; TMS: ENABLE TMS9918 VIDEO/KBD DRIVER (TMS.ASM)
+TMSENABLE	.EQU	FALSE		; TMS: ENABLE TMS9918 VIDEO/KBD DRIVER (TMS.ASM)
 TMSMODE		.EQU	TMSMODE_MBC	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MSXKBD|COLECO]
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
@@ -237,7 +238,7 @@ ESPENABLE	.EQU	FALSE		; ESP: ENABLE ESP32 IO BOARD DRIVER (ESP.ASM)
 HDSKENABLE	.EQU	FALSE		; HDSK: ENABLE SIMH HDSK DISK DRIVER (HDSK.ASM)
 HDSKTRACE	.EQU	1		; HDSK: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 ;
-PIOENABLE	.EQU	TRUE		; PIO: ENABLE ZILOG PIO DRIVER (PIO.ASM)
+PIOENABLE	.EQU	FALSE		; PIO: ENABLE ZILOG PIO DRIVER (PIO.ASM)
 PIOCNT		.EQU	2		; PIO: NUMBER OF CHIPS TO DETECT (1-2), 2 CHANNELS PER CHIP
 PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
 PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR

Source/HBIOS/cfg_dyno.asm

@@ -133,6 +133,7 @@ UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
+UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCIINTS	.EQU	TRUE		; ASCI: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3

Source/HBIOS/cfg_master.asm

@@ -169,6 +169,7 @@ UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
+UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCIINTS	.EQU	TRUE		; ASCI: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3

Source/HBIOS/cfg_mbc.asm

@@ -127,6 +127,7 @@ UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	TRUE		; UART: AUTO-DETECT DUAL UART
+UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;

Source/HBIOS/cfg_mk4.asm

@@ -133,6 +133,7 @@ UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	TRUE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
+UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCIINTS	.EQU	TRUE		; ASCI: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3

Source/HBIOS/cfg_n8.asm

@@ -135,6 +135,7 @@ UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	TRUE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
+UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCIINTS	.EQU	TRUE		; ASCI: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3

Source/HBIOS/cfg_rcz180.asm

@@ -139,6 +139,7 @@ UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
+UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCIINTS	.EQU	TRUE		; ASCI: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3

Source/HBIOS/cfg_rcz280.asm

@@ -133,6 +133,7 @@ UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
+UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;

Source/HBIOS/cfg_rcz80.asm

@@ -132,6 +132,7 @@ UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
+UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;

Source/HBIOS/cfg_rph.asm

@@ -133,6 +133,7 @@ UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
+UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCIINTS	.EQU	TRUE		; ASCI: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3

Source/HBIOS/cfg_s100.asm

@@ -133,6 +133,7 @@ UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
+UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCIINTS	.EQU	TRUE		; ASCI: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3

Source/HBIOS/cfg_sbc.asm

@@ -127,6 +127,7 @@ UARTMFP		.EQU	TRUE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	TRUE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
+UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;

Source/HBIOS/cfg_scz180.asm

@@ -133,6 +133,7 @@ UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
+UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCIINTS	.EQU	TRUE		; ASCI: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3

Source/HBIOS/cfg_z80retro.asm

@@ -125,6 +125,7 @@ UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
+UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;

Source/HBIOS/cfg_zeta.asm

@@ -114,6 +114,7 @@ UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
+UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;

Source/HBIOS/cfg_zeta2.asm

@@ -125,6 +125,7 @@ UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
+UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;

Source/HBIOS/hbios.asm

@@ -118,6 +118,7 @@ MODCNT	.SET	MODCNT + 1
 ; TinyZ80: LED Port=0x6E, bit 0, inverted, dedicated port
 ; Z80-512K: LED Port=0x6E, bit 0, inverted, dedicated port
 ; MBC: LED Port=0x70, bits 1-0, normal, shared w/ RTC port
+; DUO: LED Port=0x94, bits 1-0, normal, shared w/ RTC port
 ; 
 #IF (LEDENABLE)
   #IF (LEDMODE == LEDMODE_STD)
@@ -465,7 +466,11 @@ HBX_ROM:
 	BIT	7,A			; BIT 7 SET REQUESTS RAM PAGE
 	JR	Z,HBX_ROM		; NOT SET, SELECT ROM PAGE
 	RES	7,A			; RAM PAGE REQUESTED: CLEAR ROM BIT
+  #IF (PLATFORM == PLT_DUO)
+	ADD	A,64			; ADD 64 x 32K - RAM STARTS FROM 2048K
+  #ELSE
 	ADD	A,16			; ADD 16 x 32K - RAM STARTS FROM 512K
+  #ENDIF
 ;
 HBX_ROM:
 	RLCA				; TIMES 2 - GET 16K PAGE INSTEAD OF 32K
@@ -1310,7 +1315,13 @@ Z280_INITZ:
 	INC	A
 	OUT	(MPGSEL_1),A
   #ENDIF
-	LD	A,62
+;
+  #IF (PLATFORM == PLT_DUO)
+	LD	A,128 + (RAMSIZE / 16) - 2
+  #ELSE
+	LD	A,64 - 2
+  #ENDIF
+;
 	OUT	(MPGSEL_2),A
 	INC	A
 	OUT	(MPGSEL_3),A
@@ -2772,6 +2783,7 @@ HB_WDZ:
 ;
 	LD	A,(CB_CONDEV)		; GET CURRENT CONSOLE
 	LD	(HB_NEWCON),A		; AND INIT NEW CONSOLE VAR
+;
 #IF CRTACT
 ;
 ; BIOS IS CONFIGURED TO AUTO ACTIVATE CRT DEVICE.  FIRST,
@@ -2795,11 +2807,6 @@ HB_WDZ:
 ;
 #ENDIF
 ;
-; THIS IS A GOOD PLACE TO DETERMINE IF FRONT PANEL HARDWARE REALLY
-; EXISTS.
-;
-	CALL	FP_DETECT
-;
 #IF (FPSW_ENABLE)
 ;
 ; IF WE HAVE FRONT PANEL SWITCHES, THIS IS THE RIGHT PLACE TO HANDLE
@@ -2813,8 +2820,9 @@ HB_WDZ:
 	LD	A,FPSW_IO
 	CALL	PRTHEXBYTE
 ;
-	; THE EXISTENCE OF THE FP WAS TESTED EARLIER.  IF IT DOESN'T
-	; EXIST, BAIL OUT.
+	CALL	FP_DETECT
+;
+	; IF FP DOESN'T EXIST, BAIL OUT.
 	LD	A,(FPSW_ACTIVE)		; GET FP EXISTENCE FLAG
 	OR	A			; SET FLAGS
 	JR	NZ,HB_FP1		; IF WE HAVE ONE, CONTINUE
@@ -5114,6 +5122,99 @@ SYS_INTSET1:
 	RET				; DONE
 ;
 ;==================================================================================================
+;   Z280 INTERRUPT VECTOR TABLE
+;==================================================================================================
+;
+#IF (MEMMGR == MM_Z280)
+;
+	; THE Z280 IVT MUST BE ON A 4K BOUNDARY.  IT HAS BEEN LOCATED
+	; HERE IN AN EFFORT TO MINIMIZE WASTED SPACE.  THERE SHOULD BE
+	; A LITTLE LESS THAN 4K OF CODE ABOVE.
+;
+Z280_IVT_SLACK	.EQU	$1000 - ($ & $FFF)
+		.ECHO	"Z280 IVT SLACK occupies "
+		.ECHO	Z280_IVT_SLACK
+		.ECHO	" bytes.\n"
+		;.FILL	$1000 - ($ & $FFF)	; MUST BE 4K ALIGNED!
+		.FILL	Z280_IVT_SLACK		; MUST BE 4K ALIGNED!
+;
+Z280_IVT:
+	.DW	0, 0			; RESERVED
+	.DW	0			; NMI MSR
+	.DW	0			; NMI VECTOR
+	.DW	$0000			; INT A MSR
+	.DW	Z280_BADINT		; INT A VECTOR
+	.DW	$0000			; INT B MSR
+	.DW	Z280_BADINT		; INT B VECTOR
+	.DW	$0000			; INT C MSR
+	.DW	Z280_BADINT		; INT C VECTOR
+	.DW	$0000			; COUNTER/TIMER 0 MSR
+	.DW	Z280_BADINT		; COUNTER/TIMER 0 VECTOR
+	.DW	$0000			; COUNTER/TIMER 1 MSR
+	.DW	Z280_BADINT		; COUNTER/TIMER 1 VECTOR
+	.DW	0, 0			; RESERVED
+	.DW	$0000			; COUNTER/TIMER 2 MSR
+	.DW	Z280_BADINT		; COUNTER/TIMER 2 VECTOR
+	.DW	$0000			; DMA CHANNEL 0 MSR
+	.DW	Z280_BADINT		; DMA CHANNEL 0 VECTOR
+	.DW	$0000			; DMA CHANNEL 1 MSR
+	.DW	Z280_BADINT		; DMA CHANNEL 1 VECTOR
+	.DW	$0000			; DMA CHANNEL 2 MSR
+	.DW	Z280_BADINT		; DMA CHANNEL 2 VECTOR
+	.DW	$0000			; DMA CHANNEL 3 MSR
+	.DW	Z280_BADINT		; DMA CHANNEL 3 VECTOR
+	.DW	$0000			; UART RECEIVER MSR
+	.DW	Z280_BADINT		; UART RECEIVER VECTOR
+	.DW	$0000			; UART TRANSMITTER MSR
+	.DW	Z280_BADINT		; UART TRANSMITTER VECTOR
+	.DW	$0000			; SINGLE STEP TRAP MSR
+	.DW	Z280_SSTEP		; SINGLE STEP TRAP VECTOR
+	.DW	$0000			; BREAK ON HALT TRAP MSR
+	.DW	Z280_BRKHLT		; BREAK ON HALT TRAP VECTOR
+	.DW	$0000			; DIVISION EXCEPTION TRAP MSR
+	.DW	Z280_DIVEXC		; DIVISION EXCEPTION TRAP VECTOR
+	.DW	$0000			; STACK OVERFLOW WARNING TRAP MSR
+	.DW	Z280_STKOVR		; STACK OVERFLOW WARNING TRAP VECTOR
+	.DW	$0000			; ACCESS VIOLATION TRAP MSR
+	.DW	Z280_ACCVIO		; ACCESS VIOLATION TRAP VECTOR
+	.DW	$0000			; SYSTEM CALL TRAP MSR
+	.DW	Z280_SYSCALL		; SYSTEM CALL TRAP VECTOR
+	.DW	$0000			; PRIVILEGED INSTRUCTION TRAP MSR
+	.DW	Z280_PRIVINST		; PRIVILEGED INSTRUCTION TRAP VECTOR
+	.DW	$0000			; EPU <- MEMORY EXTENDED INSTRUCTION TRAP MSR
+	.DW	$0000			; EPU <- MEMORY EXTENDED INSTRUCTION TRAP VECTOR
+	.DW	$0000			; MEMORY <- EPU EXTENDED INSTRUCTION TRAP MSR
+	.DW	$0000			; MEMORY <- EPU EXTENDED INSTRUCTION TRAP VECTOR
+	.DW	$0000			; A <- EPU EXTENDED INSTRUCTION TRAP MSR
+	.DW	$0000			; A <- EPU EXTENDED INSTRUCTION TRAP VECTOR
+	.DW	$0000			; EPU INTERNAL OPERATION EXTENDED INSTRUCTION TRAP MSR
+	.DW	$0000			; EPU INTERNAL OPERATION EXTENDED INSTRUCTION TRAP VECTOR
+	.DW	0, 0			; RESERVED
+	.DW	0, 0			; RESERVED
+	; PROGRAM COUNTER VALUES FOR NMI/INTA (16)
+	.DW	HBX_IV00
+	.DW	HBX_IV01
+	.DW	HBX_IV02
+	.DW	HBX_IV03
+	.DW	HBX_IV04
+	.DW	HBX_IV05
+	.DW	HBX_IV06
+	.DW	HBX_IV07
+	.DW	HBX_IV08
+	.DW	HBX_IV09
+	.DW	HBX_IV0A
+	.DW	HBX_IV0B
+	.DW	HBX_IV0C
+	.DW	HBX_IV0D
+	.DW	HBX_IV0E
+	.DW	HBX_IV0F
+	; THE REMAINDER OF THE Z280 IVT IS TRUNCATED HERE BECAUSE IT
+	; TAKES A BUNCH OF SPACE AND IS NOT USED.  WE SUPPORT ONLY
+	; 16 VECTORED INTERRUPTS AND THEY MUST BE CONNECTED TO INTA.
+;
+#ENDIF
+;
+;==================================================================================================
 ;   GLOBAL HBIOS FUNCTIONS
 ;==================================================================================================
 ;
@@ -5673,94 +5774,6 @@ HB_ALLOC1:
 HB_TMPSZ	.DW	0
 HB_TMPREF	.DW	0
 ;
-;==================================================================================================
-;   Z280 INTERRUPT VECTOR TABLE
-;==================================================================================================
-;
-#IF (MEMMGR == MM_Z280)
-;
-	; THE Z280 IVT MUST BE ON A 4K BOUNDARY.  IT HAS BEEN LOCATED
-	; HERE IN AN EFFORT TO MINIMIZE WASTED SPACE.  THERE SHOULD BE
-	; A LITTLE LESS THAN 4K OF CODE ABOVE.
-;
-	.FILL	$1000 - ($ & $FFF)	; MUST BE 4K ALIGNED!
-;
-Z280_IVT:
-	.DW	0, 0			; RESERVED
-	.DW	0			; NMI MSR
-	.DW	0			; NMI VECTOR
-	.DW	$0000			; INT A MSR
-	.DW	Z280_BADINT		; INT A VECTOR
-	.DW	$0000			; INT B MSR
-	.DW	Z280_BADINT		; INT B VECTOR
-	.DW	$0000			; INT C MSR
-	.DW	Z280_BADINT		; INT C VECTOR
-	.DW	$0000			; COUNTER/TIMER 0 MSR
-	.DW	Z280_BADINT		; COUNTER/TIMER 0 VECTOR
-	.DW	$0000			; COUNTER/TIMER 1 MSR
-	.DW	Z280_BADINT		; COUNTER/TIMER 1 VECTOR
-	.DW	0, 0			; RESERVED
-	.DW	$0000			; COUNTER/TIMER 2 MSR
-	.DW	Z280_BADINT		; COUNTER/TIMER 2 VECTOR
-	.DW	$0000			; DMA CHANNEL 0 MSR
-	.DW	Z280_BADINT		; DMA CHANNEL 0 VECTOR
-	.DW	$0000			; DMA CHANNEL 1 MSR
-	.DW	Z280_BADINT		; DMA CHANNEL 1 VECTOR
-	.DW	$0000			; DMA CHANNEL 2 MSR
-	.DW	Z280_BADINT		; DMA CHANNEL 2 VECTOR
-	.DW	$0000			; DMA CHANNEL 3 MSR
-	.DW	Z280_BADINT		; DMA CHANNEL 3 VECTOR
-	.DW	$0000			; UART RECEIVER MSR
-	.DW	Z280_BADINT		; UART RECEIVER VECTOR
-	.DW	$0000			; UART TRANSMITTER MSR
-	.DW	Z280_BADINT		; UART TRANSMITTER VECTOR
-	.DW	$0000			; SINGLE STEP TRAP MSR
-	.DW	Z280_SSTEP		; SINGLE STEP TRAP VECTOR
-	.DW	$0000			; BREAK ON HALT TRAP MSR
-	.DW	Z280_BRKHLT		; BREAK ON HALT TRAP VECTOR
-	.DW	$0000			; DIVISION EXCEPTION TRAP MSR
-	.DW	Z280_DIVEXC		; DIVISION EXCEPTION TRAP VECTOR
-	.DW	$0000			; STACK OVERFLOW WARNING TRAP MSR
-	.DW	Z280_STKOVR		; STACK OVERFLOW WARNING TRAP VECTOR
-	.DW	$0000			; ACCESS VIOLATION TRAP MSR
-	.DW	Z280_ACCVIO		; ACCESS VIOLATION TRAP VECTOR
-	.DW	$0000			; SYSTEM CALL TRAP MSR
-	.DW	Z280_SYSCALL		; SYSTEM CALL TRAP VECTOR
-	.DW	$0000			; PRIVILEGED INSTRUCTION TRAP MSR
-	.DW	Z280_PRIVINST		; PRIVILEGED INSTRUCTION TRAP VECTOR
-	.DW	$0000			; EPU <- MEMORY EXTENDED INSTRUCTION TRAP MSR
-	.DW	$0000			; EPU <- MEMORY EXTENDED INSTRUCTION TRAP VECTOR
-	.DW	$0000			; MEMORY <- EPU EXTENDED INSTRUCTION TRAP MSR
-	.DW	$0000			; MEMORY <- EPU EXTENDED INSTRUCTION TRAP VECTOR
-	.DW	$0000			; A <- EPU EXTENDED INSTRUCTION TRAP MSR
-	.DW	$0000			; A <- EPU EXTENDED INSTRUCTION TRAP VECTOR
-	.DW	$0000			; EPU INTERNAL OPERATION EXTENDED INSTRUCTION TRAP MSR
-	.DW	$0000			; EPU INTERNAL OPERATION EXTENDED INSTRUCTION TRAP VECTOR
-	.DW	0, 0			; RESERVED
-	.DW	0, 0			; RESERVED
-	; PROGRAM COUNTER VALUES FOR NMI/INTA (16)
-	.DW	HBX_IV00
-	.DW	HBX_IV01
-	.DW	HBX_IV02
-	.DW	HBX_IV03
-	.DW	HBX_IV04
-	.DW	HBX_IV05
-	.DW	HBX_IV06
-	.DW	HBX_IV07
-	.DW	HBX_IV08
-	.DW	HBX_IV09
-	.DW	HBX_IV0A
-	.DW	HBX_IV0B
-	.DW	HBX_IV0C
-	.DW	HBX_IV0D
-	.DW	HBX_IV0E
-	.DW	HBX_IV0F
-	; THE REMAINDER OF THE Z280 IVT IS TRUNCATED HERE BECAUSE IT
-	; TAKES A BUNCH OF SPACE AND IS NOT USED.  WE SUPPORT ONLY
-	; 16 VECTORED INTERRUPTS AND THEY MUST BE CONNECTED TO INTA.
-;
-#ENDIF
-;
 ; Z280 BANK SELECTION (CALLED FROM PROXY)
 ;
 #IF (MEMMGR == MM_Z280)

Source/HBIOS/romldr.asm

@@ -1343,6 +1343,22 @@ diskread:
 ;
 #endif
 ;
+; Built-in mini-loader for S100 Monitor
+;
+#if (BIOS == BIOS_WBW)
+  #if (PLATFORM == PLT_S100)
+;
+s100mon:
+;
+	; Launch S100 Monitor from ROM Bank 3
+	call	ldelay			; wait for UART buf to empty
+	ld	a,BID_IMG2		; S100 monitor bank
+	ld	ix,0			; execution resumes here
+	jp	HB_BNKCALL		; do it
+;
+  #endif
+#endif
+;
 ;=======================================================================
 ; Utility functions
 ;=======================================================================
@@ -2311,6 +2327,11 @@ ra_tbl:
 ;      ---------  -------  -----  --------  -----        -------  -------  ----------
 ra_ent(str_mon,	  'M',	   KY_CL, BID_IMG0, MON_IMGLOC,  MON_LOC, MON_SIZ, MON_SERIAL)
 ra_entsiz	.equ	$ - ra_tbl
+#if (BIOS == BIOS_WBW)
+  #if (PLATFORM == PLT_S100)
+ra_ent(str_smon,  'S',	   $FF,	  bid_cur , $8000,       $8000,   $0001,   s100mon)
+  #endif
+#endif
 ra_ent(str_zsys,  'Z',	   KY_FW, BID_IMG0, ZSYS_IMGLOC, CPM_LOC, CPM_SIZ, CPM_ENT)
 ra_ent(str_cpm22, 'C',	   KY_BK, BID_IMG0, CPM_IMGLOC,  CPM_LOC, CPM_SIZ, CPM_ENT)
 #if (BIOS == BIOS_WBW)
@@ -2333,7 +2354,7 @@ ra_tbl_app:
 ;      Name	  Key	   Dsky	  Bank	    Src	         Dest	    Size     Entry
 ;      ---------  -------  -----  --------  -----       -------  -------  ----------
 ra_ent(str_mon,	  'M',	   KY_CL, bid_cur,  MON_IMGLOC,  MON_LOC, MON_SIZ, MON_SERIAL)
-ra_ent(str_zsys,  'Z',	   KY_FW, bid_cur,  ZSYS_IMGLOC,  CPM_LOC, CPM_SIZ, CPM_ENT)
+ra_ent(str_zsys,  'Z',	   KY_FW, bid_cur,  ZSYS_IMGLOC, CPM_LOC, CPM_SIZ, CPM_ENT)
 #if (DSKYENABLE)
 ra_ent(str_dsky,  'Y'+$80, KY_GO, bid_cur,  MON_IMGLOC,  MON_LOC, MON_SIZ, MON_DSKY)
 #endif
@@ -2349,6 +2370,7 @@ str_tbas	.db	"Tasty BASIC",0
 str_play	.db	"Play a Game",0
 str_upd		.db	"XModem Flash Updater",0
 str_user	.db	"User App",0
+str_smon	.db	"S100 Z180 Monitor",0
 str_egg		.db	"",0
 str_net		.db	"Network Boot",0
 str_switches	.db	"FP Switches = 0x",0

Source/HBIOS/sd.asm

@@ -9,14 +9,14 @@
 ;	- TEST XC CARD TYPE DETECTION
 ;	- TRY TO GET INIT TO FAIL, REMOVE DELAYS AT START OF GOIDLE?
 ;
-;----------------------------------------------------------------------------------------------
-; SD Signal	Active	JUHA	N8	CSIO	PPI	UART	DSD	MK4	SC	MT
-; ------------	------- ------- ------- ------- ------- ------- ------- -------	-------	-------
-; CS (DAT3)	LO ->	RTC:2	RTC:2	RTC:2	~PC:4	~MCR:3	OPR:2	SD:2	~RTC:2/3OPR:4/5
-; CLK		HI ->	RTC:1	RTC:1	CSIO	PC:1	~MCR:2	OPR:1	CSIO	CSIO	SPI
-; DI (CMD)	HI ->	RTC:0	RTC:0	CSIO	PC:0	~MCR:0	OPR:0	CSIO	CSIO	SPI
-; DO (DAT0)	HI ->	RTC:7	RTC:6	CSIO	PB:7	~MSR:5	OPR:0	CSIO	CSIO	SPI
-;----------------------------------------------------------------------------------------------
+;-----------------------------------------------------------------------------------------------------
+; SD Signal	Active	JUHA	N8	CSIO	PPI	UART	DSD	MK4	SC	MT     PIO
+; ------------	------- ------- ------- ------- ------- ------- ------- -------	-------	--------------
+; CS (DAT3)	LO ->	RTC:2	RTC:2	RTC:2	~PC:4	~MCR:3	OPR:2	SD:2	~RTC:2/3OPR:4/5~OPR:3
+; CLK		HI ->	RTC:1	RTC:1	CSIO	PC:1	~MCR:2	OPR:1	CSIO	CSIO	SPI    OPR:4
+; DI (CMD)	HI ->	RTC:0	RTC:0	CSIO	PC:0	~MCR:0	OPR:0	CSIO	CSIO	SPI    OPR:0
+; DO (DAT0)	HI ->	RTC:7	RTC:6	CSIO	PB:7	~MSR:5	OPR:0	CSIO	CSIO	SPI    OPR:7
+;-----------------------------------------------------------------------------------------------------
 ;
 ; CS = CHIP SELECT (AKA DAT3 FOR NON-SPI MODE)
 ; CLK = CLOCK
@@ -167,6 +167,7 @@ RTCDEF		.SET	RTCDEF | SD_OPRDEF	; SET DEFAULT IN HBIOS MAINLINE
 SD_DEVMAX	.EQU	1		; NUMBER OF PHYSICAL UNITS (SOCKETS)
 SD_PPIBASE	.EQU	SDPPIBASE	; BASE IO PORT FOR PPI
 SD_PPIB		.EQU	SDPPIBASE + 1	; PPI PORT B (INPUT: DOUT)
+SD_PPIB		.EQU	SDPPIBASE + 1	; PPI PORT B (INPUT: DOUT)
 SD_PPIC		.EQU	SDPPIBASE + 2	; PPI PORT C (OUTPUT: CS, CLK, DIN)
 SD_PPIX		.EQU	SDPPIBASE + 3	; PPI CONTROL PORT
 SD_OPRREG	.EQU	SD_PPIC		; PPI PORT C IS OPR REG
@@ -298,7 +299,10 @@ SD_INVCS	.EQU	FALSE		; INVERT CS
 SD_DEVMAX	.EQU	1		; NUMBER OF PHYSICAL UNITS (SOCKETS)
 SD_IOBASE	.EQU	$69		; IO BASE ADDRESS FOR SD INTERFACE
 SD_OPRREG	.EQU	SD_IOBASE	; OUTPUT PORT (OUTPUT: CS, CLK, DIN)
-SD_OPRDEF	.EQU	%11111111	; OUTPUT PORT DEFAULT STATE
+;--- WBW
+;SD_OPRDEF	.EQU	%11111111	; OUTPUT PORT DEFAULT STATE
+SD_OPRDEF	.EQU	%11101111	; OUTPUT PORT DEFAULT STATE
+;---
 SD_INPREG	.EQU	SD_IOBASE	; INPUT REGISTER
 SD_CS0		.EQU	%00001000	; SELECT
 SD_CLK		.EQU	%00010000	; CLOCK
@@ -1801,6 +1805,7 @@ SD_SETUP:
 ;
 #IF (SDMODE == SDMODE_PIO)
 	LD	A,SD_OPRDEF		; All output bits high
+	LD	(SD_OPRVAL),A		; WBW
 	OUT	(SD_OPRREG),A
 	LD	A,$CF			; Port B mode 3
 	OUT	(SD_DDR),A

Source/HBIOS/uart.asm

@@ -59,6 +59,7 @@ UARTMBASE		.EQU	$18
 UART4BASE		.EQU	$C0
 UARTRBASE		.EQU	$A0
 UARTDBASE		.EQU	$80
+UARTYBASE		.EQU	$58
 ;
 #IF (UARTINTS)
 ;
@@ -1087,6 +1088,16 @@ UART_CFG_MFP:
 	.DW	UARTCFG				; LINE CONFIGURATION
 	.DW	0				; SHOULD NEVER NEED INT HANDLER
 #ENDIF
+#IF (UARTDUO)
+UART_CFG_DUO:
+	; DUODYNE ONBOARD SERIAL PORT
+	.DB	0				; DEVICE NUMBER (UPDATED DURING INIT)
+	.DB	0				; UART TYPE
+	.DB	UARTYBASE			; IO PORT BASE (RBR, THR)
+	.DB	UARTYBASE + UART_LSR		; LINE STATUS PORT (LSR)
+	.DW	UARTCFG				; LINE CONFIGURATION
+	.DW	0				; POINTER TO RCV BUFFER STRUCT
+#ENDIF
 ;
 UART_CNT	.EQU	($ - UART_CFG) / 8
 ;

Source/ver.inc

@@ -2,7 +2,7 @@
 #DEFINE	RMN	3
 #DEFINE	RUP	0
 #DEFINE	RTP	0
-#DEFINE BIOSVER	"3.3.0-dev.33"
+#DEFINE BIOSVER	"3.3.0-dev.39"
 #define rmj	RMJ
 #define rmn	RMN
 #define rup	RUP

Source/ver.lib

@@ -3,5 +3,5 @@ rmn	equ	3
 rup	equ	0
 rtp	equ	0
 biosver	macro
-	db	"3.3.0-dev.33"
+	db	"3.3.0-dev.39"
 	endm