FDC Detection Update & Enable ESP Driver on Duodyne

- Based on reports from Martin R, the FDC detection algorithm has been updated to try reading the FDC MSR register twice to try and get the desired value of 0x80. - Dan Werner's ESP board for Duodyne is working well, so the default Duodyne config has been changed to automatically detect this board.
Merge pull request #357 from fernandocarolo/dev
2026-02-07 06:53:13 -06:00 · 2023-08-25 10:25:07 -07:00 · 2023-08-23 14:44:47 -07:00 · 2023-08-23 14:28:20 -07:00 · 2023-08-23 21:02:48 +01:00 · 2023-08-22 15:22:11 -07:00
49 changed files with 559 additions and 194 deletions
--- a/Source/Apps/FDU/fdu.doc
+++ b/Source/Apps/FDU/fdu.doc
@@ -153,7 +153,8 @@ JP2 (/FAULT) shorted, JP3 (MINI): 2-3, JP4 (/DC/RDY): 2-3.

 The RCBus Scott Baker WDC-based floppy module should be jumpered
 for I/O base address 0x50 (SV1: 11-12), JP1 (/DACK): 1-2,
-JP2 (TC): 2-3.
+JP2 (TC): 2-3.  Note that pin 1 of JPX jumpers is toward the bottom
+of the board.

 The RCBus FDC by Alan Cox (Etched Pixels) needs to be strapped
 for base I/O address 0x48.
--- a/Source/HBIOS/Config/DUO_std.asm
+++ b/Source/HBIOS/Config/DUO_std.asm
@@ -44,3 +44,5 @@ MDFFENABLE	.SET	FALSE		; MD: ENABLE FLASH FILE SYSTEM
 ;
 UARTINTS	.SET	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 ;UARTCFG	.SET	UARTCFG | SER_RTS
+;
+ESPENABLE	.SET	TRUE		; ESP: ENABLE ESP32 IO BOARD DRIVER (ESP.ASM)
--- a/Source/HBIOS/Config/MK4_std.asm
+++ b/Source/HBIOS/Config/MK4_std.asm
@@ -47,7 +47,7 @@ VGAENABLE	.SET	TRUE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VDAEMU_SERKBD	.SET	0		; VDA EMULATION: SERIAL KBD UNIT #, OR $FF FOR HW KBD
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_DIDE	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_DIDE	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ180_ext.asm
+++ b/Source/HBIOS/Config/RCZ180_ext.asm
@@ -58,7 +58,7 @@ AYMODE		.SET	AYMODE_RCZ180	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LI
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ180_nat.asm
+++ b/Source/HBIOS/Config/RCZ180_nat.asm
@@ -57,7 +57,7 @@ AYMODE		.SET	AYMODE_RCZ180	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LI
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ280_ext.asm
+++ b/Source/HBIOS/Config/RCZ280_ext.asm
@@ -56,7 +56,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ280_nat.asm
+++ b/Source/HBIOS/Config/RCZ280_nat.asm
@@ -56,7 +56,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ280_zz80mb.asm
+++ b/Source/HBIOS/Config/RCZ280_zz80mb.asm
@@ -62,7 +62,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ280_zzrc.asm
+++ b/Source/HBIOS/Config/RCZ280_zzrc.asm
@@ -70,7 +70,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ80_easy.asm
+++ b/Source/HBIOS/Config/RCZ80_easy.asm
@@ -41,6 +41,7 @@ WDOGIO		.SET	$6F		; WATCHDOG REGISTER ADR
 ;
 DSRTCENABLE	.SET	TRUE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
 RP5RTCENABLE	.SET	FALSE		; RP5C01 RTC BASED CLOCK (RP5RTC.ASM)
+INTRTCENABLE	.SET	TRUE		; ENABLE PERIODIC INTERRUPT CLOCK DRIVER (INTRTC.ASM)
 ;
 CTCENABLE	.SET	TRUE		; ENABLE ZILOG CTC SUPPORT
 CTCTIMER	.SET	TRUE		; ENABLE CTC PERIODIC TIMER
@@ -69,7 +70,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ80_jbl.asm
+++ b/Source/HBIOS/Config/RCZ80_jbl.asm
@@ -69,7 +69,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	TRUE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	FALSE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ80_kio.asm
+++ b/Source/HBIOS/Config/RCZ80_kio.asm
@@ -66,7 +66,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ80_skz.asm
+++ b/Source/HBIOS/Config/RCZ80_skz.asm
@@ -61,7 +61,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ80_std.asm
+++ b/Source/HBIOS/Config/RCZ80_std.asm
@@ -54,7 +54,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ80_tiny.asm
+++ b/Source/HBIOS/Config/RCZ80_tiny.asm
@@ -75,7 +75,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 IDE0BASE	.SET	$90		; IDE 0: IO BASE ADDRESS
--- a/Source/HBIOS/Config/RCZ80_zrc.asm
+++ b/Source/HBIOS/Config/RCZ80_zrc.asm
@@ -53,7 +53,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ80_zrc_ram.asm
+++ b/Source/HBIOS/Config/RCZ80_zrc_ram.asm
@@ -57,7 +57,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/SBC_std.asm
+++ b/Source/HBIOS/Config/SBC_std.asm
@@ -45,7 +45,7 @@ VGAENABLE	.SET	TRUE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VDAEMU_SERKBD	.SET	0		; VDA EMULATION: SERIAL KBD UNIT #, OR $FF FOR HW KBD
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_DIO3	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_DIO3	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	FALSE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/SCZ180_sc126.asm
+++ b/Source/HBIOS/Config/SCZ180_sc126.asm
@@ -59,7 +59,7 @@ AYMODE		.SET	AYMODE_RCZ180	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LI
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/SCZ180_sc130.asm
+++ b/Source/HBIOS/Config/SCZ180_sc130.asm
@@ -60,7 +60,7 @@ AYMODE		.SET	AYMODE_RCZ180	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LI
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/SCZ180_sc140.asm
+++ b/Source/HBIOS/Config/SCZ180_sc140.asm
@@ -54,7 +54,7 @@ AYMODE		.SET	AYMODE_LINC	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LINC
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/SCZ180_sc503.asm
+++ b/Source/HBIOS/Config/SCZ180_sc503.asm
@@ -54,7 +54,7 @@ AYMODE		.SET	AYMODE_LINC	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LINC
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/ZETA2_std.asm
+++ b/Source/HBIOS/Config/ZETA2_std.asm
@@ -35,7 +35,7 @@ UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 UARTSBC		.SET	TRUE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_ZETA2	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_ZETA2	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 PPIDEENABLE	.SET	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
--- a/Source/HBIOS/Config/ZETA_std.asm
+++ b/Source/HBIOS/Config/ZETA_std.asm
@@ -35,7 +35,7 @@ UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 UARTSBC		.SET	TRUE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_ZETA	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_ZETA	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 PPIDEENABLE	.SET	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
--- a/Source/HBIOS/cfg_duo.asm
+++ b/Source/HBIOS/cfg_duo.asm
@@ -1,6 +1,6 @@
 ;
 ;==================================================================================================
-;   ROMWBW 2.X CONFIGURATION DEFAULTS FOR DUODYNE
+;   ROMWBW 3.X CONFIGURATION DEFAULTS FOR DUODYNE
 ;==================================================================================================
 ;
 ; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
@@ -126,14 +126,13 @@ UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG	; UART: LINE CONFIG FOR UART PORTS
 UARTCASSPD	.EQU	SER_300_8N1	; UART: ECB CASSETTE UART DEFAULT SPEED
-UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTSBC		.EQU	TRUE		; UART: AUTO-DETECT SBC/ZETA/DUO ONBOARD UART
 UARTSBCFORCE	.EQU	FALSE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
 UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
-UARTDUO		.EQU	TRUE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;
@@ -237,6 +236,7 @@ PRPCONENABLE	.EQU	TRUE		; PRP: ENABLE PROPIO DRIVER VIDEO/KBD SUPPORT
 PPPENABLE	.EQU	FALSE		; PPP: ENABLE ZETA PARALLEL PORT PROPELLER BOARD DRIVER (PPP.ASM)
 ;
 ESPENABLE	.EQU	FALSE		; ESP: ENABLE ESP32 IO BOARD DRIVER (ESP.ASM)
+ESPCONENABLE	.EQU	TRUE		; ESP: ENABLE ESP32 CONSOLE IO DRIVER VIDEO/KBD SUPPORT
 ;
 HDSKENABLE	.EQU	FALSE		; HDSK: ENABLE SIMH HDSK DISK DRIVER (HDSK.ASM)
 HDSKTRACE	.EQU	1		; HDSK: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
@@ -299,5 +299,5 @@ DMAENABLE	.EQU	TRUE		; DMA: ENABLE DMA DRIVER (DMA.ASM)
 DMABASE		.EQU	$40		; DMA: DMA BASE ADDRESS
 DMAMODE		.EQU	DMAMODE_DUO	; DMA: DMA MODE (NONE|ECB|Z180|Z280|RC|MBC|DUO)
 ;
-YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER (MUTE STUB)
-VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76469s/CTC)
+YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER
+VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76489s/CTC)
--- a/Source/HBIOS/cfg_dyno.asm
+++ b/Source/HBIOS/cfg_dyno.asm
@@ -1,6 +1,6 @@
 ;
 ;==================================================================================================
-;   ROMWBW 2.X CONFIGURATION DEFAULTS FOR DYNO
+;   ROMWBW 3.X CONFIGURATION DEFAULTS FOR DYNO
 ;==================================================================================================
 ;
 ; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
@@ -129,14 +129,13 @@ UARTENABLE	.EQU	FALSE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG | SER_RTS	; UART: LINE CONFIG FOR UART PORTS
-UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA/DUO ONBOARD UART
 UARTSBCFORCE	.EQU	FALSE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
 UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
-UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCIINTS	.EQU	TRUE		; ASCI: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
@@ -285,5 +284,5 @@ DMAENABLE	.EQU	FALSE		; DMA: ENABLE DMA DRIVER (DMA.ASM)
 DMABASE		.EQU	$E0		; DMA: DMA BASE ADDRESS
 DMAMODE		.EQU	DMAMODE_Z180	; DMA: DMA MODE (NONE|ECB|Z180|Z280|RC|MBC|DUO)
 ;
-YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER (MUTE STUB)
-VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76469s/CTC)
+YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER
+VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76489s/CTC)
--- a/Source/HBIOS/cfg_master.asm
+++ b/Source/HBIOS/cfg_master.asm
@@ -1,6 +1,6 @@
 ;
 ;==================================================================================================
-;   ROMWBW 2.X CONFIGURATION MASTER
+;   ROMWBW 3.X CONFIGURATION MASTER
 ;==================================================================================================
 ;
 ; THIS FILE IS *NOT* A REAL CONFIGURATION FILE.	 IT IS A MASTER TEMPLATE FILE
@@ -165,14 +165,13 @@ UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG	; UART: LINE CONFIG FOR UART PORTS
 UARTCASSPD	.EQU	SER_300_8N1	; UART: ECB CASSETTE UART DEFAULT SPEED
-UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA/DUO ONBOARD UART
 UARTSBCFORCE	.EQU	FALSE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
 UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
-UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCIINTS	.EQU	TRUE		; ASCI: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
@@ -373,5 +372,5 @@ DMAENABLE	.EQU	FALSE		; DMA: ENABLE DMA DRIVER (DMA.ASM)
 DMABASE		.EQU	$E0		; DMA: DMA BASE ADDRESS
 DMAMODE		.EQU	DMAMODE_NONE	; DMA: DMA MODE (NONE|ECB|Z180|Z280|RC|MBC|DUO)
 ;
-YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER (MUTE STUB)
-VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76469s/CTC)
+YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER
+VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76489s/CTC)
--- a/Source/HBIOS/cfg_mbc.asm
+++ b/Source/HBIOS/cfg_mbc.asm
@@ -1,6 +1,6 @@
 ;
 ;==================================================================================================
-;   ROMWBW 2.X CONFIGURATION DEFAULTS FOR MBC
+;   ROMWBW 3.X CONFIGURATION DEFAULTS FOR MBC
 ;==================================================================================================
 ;
 ; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
@@ -123,14 +123,13 @@ UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG	; UART: LINE CONFIG FOR UART PORTS
 UARTCASSPD	.EQU	SER_300_8N1	; UART: ECB CASSETTE UART DEFAULT SPEED
-UARTSBC		.EQU	TRUE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTSBC		.EQU	TRUE		; UART: AUTO-DETECT SBC/ZETA/DUO ONBOARD UART
 UARTSBCFORCE	.EQU	FALSE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
 UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	TRUE		; UART: AUTO-DETECT DUAL UART
-UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;
@@ -297,6 +296,5 @@ DMAENABLE	.EQU	FALSE		; DMA: ENABLE DMA DRIVER (DMA.ASM)
 DMABASE		.EQU	$E0		; DMA: DMA BASE ADDRESS
 DMAMODE		.EQU	DMAMODE_MBC	; DMA: DMA MODE (NONE|ECB|Z180|Z280|RC|MBC|DUO)
 ;
-YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER (MUTE STUB)
-VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76469s/CTC)
-
+YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER
+VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76489s/CTC)
--- a/Source/HBIOS/cfg_mk4.asm
+++ b/Source/HBIOS/cfg_mk4.asm
@@ -1,6 +1,6 @@
 ;
 ;==================================================================================================
-;   ROMWBW 2.X CONFIGURATION FOR MARK IV
+;   ROMWBW 3.X CONFIGURATION FOR MARK IV
 ;==================================================================================================
 ;
 ; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
@@ -129,14 +129,13 @@ UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG	; UART: LINE CONFIG FOR UART PORTS
 UARTCASSPD	.EQU	SER_300_8N1	; UART: ECB CASSETTE UART DEFAULT SPEED
-UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA/DUO ONBOARD UART
 UARTSBCFORCE	.EQU	FALSE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
 UARTCAS		.EQU	TRUE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	TRUE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
-UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCIINTS	.EQU	TRUE		; ASCI: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
@@ -294,5 +293,5 @@ DMAENABLE	.EQU	FALSE		; DMA: ENABLE DMA DRIVER (DMA.ASM)
 DMABASE		.EQU	$E0		; DMA: DMA BASE ADDRESS
 DMAMODE		.EQU	DMAMODE_ECB	; DMA: DMA MODE (NONE|ECB|Z180|Z280|RC|MBC|DUO)
 ;
-YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER (MUTE STUB)
-VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76469s/CTC)
+YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER 
+VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76489s/CTC)
--- a/Source/HBIOS/cfg_n8.asm
+++ b/Source/HBIOS/cfg_n8.asm
@@ -1,6 +1,6 @@
 ;
 ;==================================================================================================
-;   ROMWBW 2.X CONFIGURATION FOR N8
+;   ROMWBW 3.X CONFIGURATION FOR N8
 ;==================================================================================================
 ;
 ; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
@@ -131,14 +131,13 @@ UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG	; UART: LINE CONFIG FOR UART PORTS
 UARTCASSPD	.EQU	SER_300_8N1	; UART: ECB CASSETTE UART DEFAULT SPEED
-UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA/DUO ONBOARD UART
 UARTSBCFORCE	.EQU	FALSE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
 UARTCAS		.EQU	TRUE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	TRUE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
-UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCIINTS	.EQU	TRUE		; ASCI: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
@@ -287,5 +286,5 @@ DMAENABLE	.EQU	FALSE		; DMA: ENABLE DMA DRIVER (DMA.ASM)
 DMABASE		.EQU	$E0		; DMA: DMA BASE ADDRESS
 DMAMODE		.EQU	DMAMODE_Z180	; DMA: DMA MODE (NONE|ECB|Z180|Z280|RC|MBC|DUO)
 ;
-YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER (MUTE STUB)
-VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76469s/CTC)
+YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER 
+VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76489s/CTC)
--- a/Source/HBIOS/cfg_rcz180.asm
+++ b/Source/HBIOS/cfg_rcz180.asm
@@ -1,6 +1,6 @@
 ;
 ;==================================================================================================
-;   ROMWBW 2.X CONFIGURATION DEFAULTS FOR RCBUS Z180 CPU
+;   ROMWBW 3.X CONFIGURATION DEFAULTS FOR RCBUS Z180 CPU
 ;==================================================================================================
 ;
 ; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
@@ -135,14 +135,13 @@ UARTENABLE	.EQU	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG | SER_RTS	; UART: LINE CONFIG FOR UART PORTS
-UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA/DUO ONBOARD UART
 UARTSBCFORCE	.EQU	FALSE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
 UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
-UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCIINTS	.EQU	TRUE		; ASCI: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
@@ -311,5 +310,5 @@ DMAENABLE	.EQU	FALSE		; DMA: ENABLE DMA DRIVER (DMA.ASM)
 DMABASE		.EQU	$E0		; DMA: DMA BASE ADDRESS
 DMAMODE		.EQU	DMAMODE_Z180	; DMA: DMA MODE (NONE|ECB|Z180|Z280|RC|MBC|DUO)
 ;
-YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER (MUTE STUB)
-VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76469s/CTC)
+YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER
+VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76489s/CTC)
--- a/Source/HBIOS/cfg_rcz280.asm
+++ b/Source/HBIOS/cfg_rcz280.asm
@@ -1,6 +1,6 @@
 ;
 ;==================================================================================================
-;   ROMWBW 2.X CONFIGURATION DEFAULTS FOR RCBUS Z280 CPU
+;   ROMWBW 3.X CONFIGURATION DEFAULTS FOR RCBUS Z280 CPU
 ;==================================================================================================
 ;
 ; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
@@ -129,14 +129,13 @@ UARTENABLE	.EQU	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG | SER_RTS	; UART: LINE CONFIG FOR UART PORTS
-UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA/DUO ONBOARD UART
 UARTSBCFORCE	.EQU	FALSE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
 UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
-UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;
@@ -315,5 +314,5 @@ DMAENABLE	.EQU	FALSE		; DMA: ENABLE DMA DRIVER (DMA.ASM)
 DMABASE		.EQU	$E0		; DMA: DMA BASE ADDRESS
 DMAMODE		.EQU	DMAMODE_Z280	; DMA: DMA MODE (NONE|ECB|Z180|Z280|RC|MBC|DUO)
 ;
-YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER (MUTE STUB)
-VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76469s/CTC)
+YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER
+VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76489s/CTC)
--- a/Source/HBIOS/cfg_rcz80.asm
+++ b/Source/HBIOS/cfg_rcz80.asm
@@ -1,6 +1,6 @@
 ;
 ;==================================================================================================
-;   ROMWBW 2.X CONFIGURATION DEFAULTS FOR RCBUS Z80
+;   ROMWBW 3.X CONFIGURATION DEFAULTS FOR RCBUS Z80
 ;==================================================================================================
 ;
 ; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
@@ -128,14 +128,13 @@ UARTENABLE	.EQU	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG | SER_RTS	; UART: LINE CONFIG FOR UART PORTS
-UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA/DUO ONBOARD UART
 UARTSBCFORCE	.EQU	FALSE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
 UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
-UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;
@@ -309,5 +308,5 @@ DMAENABLE	.EQU	FALSE		; DMA: ENABLE DMA DRIVER (DMA.ASM)
 DMABASE		.EQU	$E0		; DMA: DMA BASE ADDRESS
 DMAMODE		.EQU	DMAMODE_RC	; DMA: DMA MODE (NONE|ECB|Z180|Z280|RC|MBC|DUO)
 ;
-YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER (MUTE STUB)
-VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76469s/CTC)
+YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER
+VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76489s/CTC)
--- a/Source/HBIOS/cfg_rph.asm
+++ b/Source/HBIOS/cfg_rph.asm
@@ -1,6 +1,6 @@
 ;
 ;==================================================================================================
-;   ROMWBW 2.X CONFIGURATION FOR RHYOPHYRE
+;   ROMWBW 3.X CONFIGURATION FOR RHYOPHYRE
 ;==================================================================================================
 ;
 ; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
@@ -87,7 +87,7 @@ DSKYDSKACT	.EQU	TRUE		; ENABLES DISK ACTIVITY ON DSKY DISPLAY
 ICMENABLE	.EQU	FALSE		; ENABLES ORIGINAL DSKY ICM DRIVER (7218)
 ICMPPIBASE	.EQU	RPH_PPI0	; BASE I/O ADDRESS OF ICM PPI
 PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
-PKDPPIBASE	.EQU	RPH_PPI0		; BASE I/O ADDRESS OF PKD PPI
+PKDPPIBASE	.EQU	RPH_PPI0	; BASE I/O ADDRESS OF PKD PPI
 PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
 ;
 BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
@@ -129,14 +129,13 @@ UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG	; UART: LINE CONFIG FOR UART PORTS
 UARTCASSPD	.EQU	SER_300_8N1	; UART: ECB CASSETTE UART DEFAULT SPEED
-UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA/DUO ONBOARD UART
 UARTSBCFORCE	.EQU	FALSE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
 UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
-UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCIINTS	.EQU	TRUE		; ASCI: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
@@ -256,7 +255,7 @@ PIO4BASE	.EQU	$90		; PIO: PIO REGISTERS BASE ADR FOR ECB 4P BOARD
 PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)
 PIOZBASE	.EQU	$88		; PIO: PIO REGISTERS BASE ADR FOR ECB ZP BOARD
 PIO_SBC		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR 8255 CHIP
-PIOSBASE	.EQU	RPH_PPI0		; PIO: PIO REGISTERS BASE ADR FOR SBC PPI
+PIOSBASE	.EQU	RPH_PPI0	; PIO: PIO REGISTERS BASE ADR FOR SBC PPI
 ;
 UFENABLE	.EQU	FALSE		; UF: ENABLE ECB USB FIFO DRIVER (UF.ASM)
 FIFO_BASE	.EQU	$0C		; UF: REGISTERS BASE ADR
@@ -276,5 +275,5 @@ DMAENABLE	.EQU	FALSE		; DMA: ENABLE DMA DRIVER (DMA.ASM)
 DMABASE		.EQU	$E0		; DMA: DMA BASE ADDRESS
 DMAMODE		.EQU	DMAMODE_Z180	; DMA: DMA MODE (NONE|ECB|Z180|Z280|RC|MBC|DUO)
 ;
-YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER (MUTE STUB)
-VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76469s/CTC)
+YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER
+VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76489s/CTC)
--- a/Source/HBIOS/cfg_s100.asm
+++ b/Source/HBIOS/cfg_s100.asm
@@ -1,6 +1,6 @@
 ;
 ;==================================================================================================
-;   ROMWBW 2.X CONFIGURATION DEFAULTS FOR S100 Z180
+;   ROMWBW 3.X CONFIGURATION DEFAULTS FOR S100 Z180
 ;==================================================================================================
 ;
 ; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
@@ -129,14 +129,13 @@ UARTENABLE	.EQU	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG | SER_RTS	; UART: LINE CONFIG FOR UART PORTS
-UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA/DUO ONBOARD UART
 UARTSBCFORCE	.EQU	FALSE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
 UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
-UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCIINTS	.EQU	TRUE		; ASCI: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
@@ -305,5 +304,5 @@ DMAENABLE	.EQU	FALSE		; DMA: ENABLE DMA DRIVER (DMA.ASM)
 DMABASE		.EQU	$E0		; DMA: DMA BASE ADDRESS
 DMAMODE		.EQU	DMAMODE_Z180	; DMA: DMA MODE (NONE|ECB|Z180|Z280|RC|MBC|DUO)
 ;
-YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER (MUTE STUB)
-VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76469s/CTC)
+YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER
+VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76489s/CTC)
--- a/Source/HBIOS/cfg_sbc.asm
+++ b/Source/HBIOS/cfg_sbc.asm
@@ -1,6 +1,6 @@
 ;
 ;==================================================================================================
-;   ROMWBW 2.X CONFIGURATION DEFAULTS FOR SBC
+;   ROMWBW 3.X CONFIGURATION DEFAULTS FOR SBC
 ;==================================================================================================
 ;
 ; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
@@ -123,14 +123,13 @@ UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG	; UART: LINE CONFIG FOR UART PORTS
 UARTCASSPD	.EQU	SER_300_8N1	; UART: ECB CASSETTE UART DEFAULT SPEED
-UARTSBC		.EQU	TRUE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTSBC		.EQU	TRUE		; UART: AUTO-DETECT SBC/ZETA/DUO ONBOARD UART
 UARTSBCFORCE	.EQU	FALSE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
 UARTCAS		.EQU	TRUE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	TRUE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	TRUE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
-UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;
@@ -275,5 +274,5 @@ DMAENABLE	.EQU	FALSE		; DMA: ENABLE DMA DRIVER (DMA.ASM)
 DMABASE		.EQU	$E0		; DMA: DMA BASE ADDRESS
 DMAMODE		.EQU	DMAMODE_ECB	; DMA: DMA MODE (NONE|ECB|Z180|Z280|RC|MBC|DUO)
 ;
-YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER (MUTE STUB)
-VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76469s/CTC)
+YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER
+VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76489s/CTC)
--- a/Source/HBIOS/cfg_scz180.asm
+++ b/Source/HBIOS/cfg_scz180.asm
@@ -1,6 +1,6 @@
 ;
 ;==================================================================================================
-;   ROMWBW 2.X CONFIGURATION DEFAULTS FOR SC Z180 VARIANTS (SC126, SC130, ETC.)
+;   ROMWBW 3.X CONFIGURATION DEFAULTS FOR SC Z180 VARIANTS (SC126, SC130, ETC.)
 ;==================================================================================================
 ;
 ; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
@@ -129,14 +129,13 @@ UARTENABLE	.EQU	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG | SER_RTS	; UART: LINE CONFIG FOR UART PORTS
-UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA/DUO ONBOARD UART
 UARTSBCFORCE	.EQU	FALSE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
 UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
-UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ASCIINTS	.EQU	TRUE		; ASCI: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
@@ -305,5 +304,5 @@ DMAENABLE	.EQU	FALSE		; DMA: ENABLE DMA DRIVER (DMA.ASM)
 DMABASE		.EQU	$E0		; DMA: DMA BASE ADDRESS
 DMAMODE		.EQU	DMAMODE_Z180	; DMA: DMA MODE (NONE|ECB|Z180|Z280|RC|MBC|DUO)
 ;
-YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER (MUTE STUB)
-VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76469s/CTC)
+YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER
+VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76489s/CTC)
--- a/Source/HBIOS/cfg_una.asm
+++ b/Source/HBIOS/cfg_una.asm
@@ -1,6 +1,6 @@
 ;
 ;==================================================================================================
-;   ROMWBW 2.X CONFIGURATION DEFAULTS FOR UNA
+;   ROMWBW 3.X CONFIGURATION DEFAULTS FOR UNA
 ;==================================================================================================
 ;
 ; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
--- a/Source/HBIOS/cfg_z80retro.asm
+++ b/Source/HBIOS/cfg_z80retro.asm
@@ -1,6 +1,6 @@
 ;
 ;==================================================================================================
-;   ROMWBW 2.X CONFIGURATION DEFAULTS FOR SIMPLE Z80 RETRO
+;   ROMWBW 3.X CONFIGURATION DEFAULTS FOR SIMPLE Z80 RETRO
 ;==================================================================================================
 ;
 ; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
@@ -121,14 +121,13 @@ UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG	; UART: LINE CONFIG FOR UART PORTS
 UARTCASSPD	.EQU	SER_300_8N1	; UART: ECB CASSETTE UART DEFAULT SPEED
-UARTSBC		.EQU	TRUE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTSBC		.EQU	TRUE		; UART: AUTO-DETECT SBC/ZETA/DUO ONBOARD UART
 UARTSBCFORCE	.EQU	FALSE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
 UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
-UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;
@@ -236,5 +235,5 @@ DMAENABLE	.EQU	FALSE		; DMA: ENABLE DMA DRIVER (DMA.ASM)
 DMABASE		.EQU	$E0		; DMA: DMA BASE ADDRESS
 DMAMODE		.EQU	DMAMODE_NONE	; DMA: DMA MODE (NONE|ECB|Z180|Z280|RC|MBC|DUO)
 ;
-YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER (MUTE STUB)
-VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76469s/CTC)
+YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER
+VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76489s/CTC)
--- a/Source/HBIOS/cfg_zeta.asm
+++ b/Source/HBIOS/cfg_zeta.asm
@@ -1,6 +1,6 @@
 ;
 ;==================================================================================================
-;   ROMWBW 2.X CONFIGURATION DEFAULTS FOR ZETA V1
+;   ROMWBW 3.X CONFIGURATION DEFAULTS FOR ZETA V1
 ;==================================================================================================
 ;
 ; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
@@ -117,7 +117,6 @@ UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
-UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;
@@ -207,5 +206,5 @@ DMAENABLE	.EQU	FALSE		; DMA: ENABLE DMA DRIVER (DMA.ASM)
 DMABASE		.EQU	$E0		; DMA: DMA BASE ADDRESS
 DMAMODE		.EQU	DMAMODE_NONE	; DMA: DMA MODE (NONE|ECB|Z180|Z280|RC|MBC|DUO)
 ;
-YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER (MUTE STUB)
-VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76469s/CTC)
+YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER
+VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76489s/CTC)
--- a/Source/HBIOS/cfg_zeta2.asm
+++ b/Source/HBIOS/cfg_zeta2.asm
@@ -1,6 +1,6 @@
 ;
 ;==================================================================================================
-;   ROMWBW 2.X CONFIGURATION DEFAULTS FOR ZETA V2
+;   ROMWBW 3.X CONFIGURATION DEFAULTS FOR ZETA V2
 ;==================================================================================================
 ;
 ; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
@@ -121,14 +121,13 @@ UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG	; UART: LINE CONFIG FOR UART PORTS
 UARTCASSPD	.EQU	SER_300_8N1	; UART: ECB CASSETTE UART DEFAULT SPEED
-UARTSBC		.EQU	TRUE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
+UARTSBC		.EQU	TRUE		; UART: AUTO-DETECT SBC/ZETA/DUO ONBOARD UART
 UARTSBCFORCE	.EQU	FALSE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
 UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
 UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
 UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
 UARTRC		.EQU	FALSE		; UART: AUTO-DETECT RC UART
 UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
-UARTDUO		.EQU	FALSE		; UART: AUTO-DETECT DUODYNE UART
 ;
 ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
 ;
@@ -219,4 +218,4 @@ DMABASE		.EQU	$E0		; DMA: DMA BASE ADDRESS
 DMAMODE		.EQU	DMAMODE_NONE	; DMA: DMA MODE (NONE|ECB|Z180|Z280|RC|MBC|DUO)
 ;
 YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER (MUTE STUB)
-VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76469s/CTC)
+VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76489s/CTC)
--- a/Source/HBIOS/esp.asm
+++ b/Source/HBIOS/esp.asm
@@ -7,20 +7,22 @@
 ;==================================================================================================
 ;
 ; TODO:
+; - CLEAR CONSOLE SCREEN AT INITIALIZATION
+; - INITIALIZE BAUD/MODE OF SERIAL INTERFACES AT INITIALIZATION
 ;
 ESP_IOBASE	.EQU	$9C
 ESP_0_IO	.EQU	ESP_IOBASE + 0
 ESP_1_IO	.EQU	ESP_IOBASE + 1
 ESP_STAT	.EQU	ESP_IOBASE + 2
 ;
-; ESP  STATUS PORT
-; MSB XX S S S S S S
-;        | | | | | +- ESP0 READY OUTPUT
-;        | | | | +--- ESP0 BUSY
-;        | | | +----- ESP0 SPARE
-;        | | +------- ESP1 READY OUTPUT
-;        | +--------- ESP1 BUSY
-;        +----------- ESP1 SPARE
+; ESP   STATUS PORT
+; MSB X X S S S S S S
+;         | | | | | +- ESP0 READY OUTPUT
+;         | | | | +--- ESP0 BUSY
+;         | | | +----- ESP0 SPARE
+;         | | +------- ESP1 READY OUTPUT
+;         | +--------- ESP1 BUSY
+;         +----------- ESP1 SPARE
 ;
 ESP_0_RDY	.EQU	%00000001
 ESP_0_BUSY	.EQU	%00000010
@@ -32,12 +34,25 @@ ESP_1_SPARE	.EQU	%00100000
 ; COMMAND OPCODES
 ;
 ESP_CMD_NOP	.EQU	0		; NO OP
-ESP_CMD_COUT	.EQU	1		; CHAR OUT
-ESP_CMD_SOUT	.EQU	2		; STRING OUT
-ESP_CMD_KIN	.EQU	3		; KEY IN
-ESP_CMD_KST	.EQU	4		; KBD BUF STATUS
+ESP_0_CMD_COUT	.EQU	1		; CHAR OUT
+ESP_0_CMD_CSTR	.EQU	2		; STRING OUT
+ESP_0_CMD_KIN	.EQU	3		; KEY IN
+ESP_0_CMD_KST	.EQU	4		; KBD BUF STATUS
+ESP_CMD_SBAUD	.EQU	6		; SET SERIAL BAUD RATE
+ESP_CMD_SMODE	.EQU	7		; SET SERIAL LINE MODE
+ESP_CMD_SOUT	.EQU	8		; SERIAL BYTE OUT
+ESP_CMD_SIN	.EQU	10		; SERIAL BYTE IN
+ESP_CMD_SST	.EQU	11		; SERIAL INPUT STATUS
 ESP_CMD_DISC	.EQU	$FF		; DISCOVER
 ;
+; ESP CONFIG TABLE ENTRY OFFSETS
+;
+ESP_CFG_DEV	.EQU	0		; DEVICE NUMBER
+ESP_CFG_IO	.EQU	1		; ESP I/O PORT
+ESP_CFG_ST	.EQU	2		; ESP STATUS PORT
+ESP_CFG_RDYMSK	.EQU	3		; ESP READY MASK
+ESP_CFG_BSYMSK	.EQU	4		; ESP BUSY MASK
+;
 ; GLOBAL ESP INITIALIZATION
 ;
 ESP_INIT:
@@ -47,16 +62,63 @@ ESP_INIT:
 	LD	A,ESP_IOBASE
 	CALL	PRTHEXBYTE
 ;
+	XOR	A			; ZERO ACCUM
+	LD	(ESP_PRES),A		; CLEAR MODULE PRESENCE BITS
+;
+	; DETECT FIRST ESP32 MODULE
+	PRTS(" A=$")
+	LD	IY,ESPSER0_CFG
 	CALL	ESP_DETECT
+	JR	Z,ESP_INIT1		; FOUND
 	LD	DE,ESP_STR_NOHW
-	JP	NZ,WRITESTR
+	CALL	WRITESTR
+	JR	ESP_INIT2
 ;
-	; PRINT FIRMWARE VERSION
-	PRTS(" F/W=$")
+ESP_INIT1:
 	CALL	ESP_PRTVER
+	
+	LD	A,(ESP_PRES)
+	SET	0,A
+	LD	(ESP_PRES),A
+	
 ;
+ESP_INIT2:
+	; DETECT SECOND ESP32 MODULE
+	PRTS(" B=$")
+	LD	IY,ESPSER1_CFG
+	CALL	ESP_DETECT
+	JR	Z,ESP_INIT3		; FOUND
+	LD	DE,ESP_STR_NOHW
+	CALL	WRITESTR
+	JR	ESP_INIT4
+;
+ESP_INIT3:
+	CALL	ESP_PRTVER
+
+	LD	A,(ESP_PRES)
+	SET	1,A
+	LD	(ESP_PRES),A
+
+;
+ESP_INIT4:
+	; INITIALIZE FIRST MODULE CHILD DRIVERS
+	LD	A,(ESP_PRES)
+	BIT	0,A
+	JR	Z,ESP_INIT5
+	LD	IY,ESPSER0_CFG
+	CALL	ESPSER_INIT		; SERIAL INITIALIZATION
+	LD	IY,ESPCON0_CFG
 	CALL	ESPCON_INIT		; CONSOLE INITIALIZATION
 ;
+ESP_INIT5:
+	; INITIALIZE SECOND MODULE CHILD DRIVERS
+	LD	A,(ESP_PRES)
+	BIT	1,A
+	JR	Z,ESP_INIT6
+	LD	IY,ESPSER1_CFG
+	CALL	ESPSER_INIT		; SERIAL INITIALIZATION
+;
+ESP_INIT6:
 	RET
 ;
 ;==================================================================================================
@@ -71,24 +133,14 @@ ESP_DETECT:
 ;
 	; LOOK FOR SIGNATURE STARTING WITH "ESP"
 	CALL	ESP_INWAIT		; ATTEMPT TO GET CHAR
-	;CALL	PRTHEXBYTE
 	CP	'E'
 	RET	NZ
 	CALL	ESP_INWAIT		; ATTEMPT TO GET CHAR
-	;CALL	PRTHEXBYTE
 	CP	'S'
 	RET	NZ
 	CALL	ESP_INWAIT		; ATTEMPT TO GET CHAR
-	;CALL	PRTHEXBYTE
 	CP	'P'
 	RET
-
-	;LD	DE,10			; DELAY 160US
-	;CALL	VDELAY			; ... TO ENSURE OUTPUT RDY SET
-	;IN	A,(ESP_STAT)		; GET STATUS
-	;AND	ESP_0_RDY		; ISOLATE OUTPUT READY BIT
-	;XOR	ESP_0_RDY		; INVERT SO 0=FOUND
-	;RET				; DONE
 ;
 ; CLEAR ESP INPUT QUEUE
 ;
@@ -98,9 +150,10 @@ ESP_CLR0:
 	CALL	ESP_WTNBSY		; WAIT TILL NOT BUSY
 	RET	NZ			; BAIL OUT IF TIMEOUT
 	IN	A,(ESP_STAT)		; GET STATUS
-	AND	ESP_0_RDY		; IS THERE MORE DATA?
+	AND	(IY+ESP_CFG_RDYMSK)	; IS THERE MORE DATA?
 	RET	Z			; IF NOT, DONE
-	IN	A,(ESP_0_IO)		; GET CHAR
+	LD	C,(IY+ESP_CFG_IO)	; ESP I/O PORT
+	IN	A,(C)			; GET BYTE
 	DJNZ	ESP_CLR0		; LOOP TILL DONE
 	OR	$FF			; SIGNAL FAILURE
 	RET
@@ -115,7 +168,8 @@ ESP_PRTVER:
 ESP_PRTVER1:
 	CALL	ESP_WTNBSY		; WAIT TILL NOT BUSY
 	IN	A,(ESP_STAT)		; GET STATUS
-	AND	ESP_0_RDY		; ISOLATE OUTPUT READY BIT
+	;AND	ESP_0_RDY		; ISOLATE OUTPUT READY BIT
+	AND	(IY+ESP_CFG_RDYMSK)	; ISOLATE OUTPUT READY BIT
 	RET	Z			; DONE IF NOTHING READY
 	CALL	ESP_IN			; GET NEXT CHAR
 	CALL	COUT			; PRINT CHAR
@@ -127,7 +181,8 @@ ESP_OUT:
 	PUSH	AF			; SAVE VALUE
 	CALL	ESP_WTNBSY		; WAIT TILL NOT BUSY
 	POP	AF			; POP VALUE
-	OUT	(ESP_0_IO),A		; SEND CHARACTER
+	LD	C,(IY+ESP_CFG_IO)	; ESP I/O PORT
+	OUT	(C),A			; SEND BYTE
 	JR	ESP_WTBSY		; RETURN VIA WTBSY
 ;
 ; GET BYTE FROM ESP (BLOCKING)
@@ -142,7 +197,8 @@ ESP_INWAIT:
 ESP_IN:
 	CALL	ESP_WTNBSY		; WAIT TILL NOT BUSY
 ESP_IN1:	
-	IN	A,(ESP_0_IO)		; GET BYTE
+	LD	C,(IY+ESP_CFG_IO)	; ESP I/O PORT
+	IN	A,(C)			; GET BYTE
 	PUSH	AF			; SAVE VALUE
 	CALL	ESP_WTBSY		; WAIT TILL BUSY
 	POP	AF			; RESTORE VALUE
@@ -153,8 +209,9 @@ ESP_IN1:
 ESP_WTNBSY:
 	LD	B,0			; MAX TRIES
 ESP_WTNBSY1:	
-	IN	A,(ESP_STAT)		; GET STATUS
-	AND	ESP_0_BUSY		; IS ESP BUSY?
+	LD	C,(IY+ESP_CFG_ST)	; ESP STATUS PORT
+	IN	A,(C)			; GET STATUS
+	AND	(IY+ESP_CFG_BSYMSK)	; IS ESP BUSY?
 	RET	Z			; RETURN IF NOT BUSY
 	DJNZ	ESP_WTNBSY1		; ELSE LOOP
 	OR	$FF			; SIGNAL TIMEOUT
@@ -165,9 +222,10 @@ ESP_WTNBSY1:
 ESP_WTBSY:
 	LD	B,20			; MAX TRIES
 ESP_WTBSY1:	
-	IN	A,(ESP_STAT)		; GET STATUS
-	AND	ESP_0_BUSY		; IS ESP BUSY?
-	XOR	ESP_0_BUSY		; INVERT
+	LD	C,(IY+ESP_CFG_ST)	; ESP STATUS PORT
+	IN	A,(C)			; GET STATUS
+	XOR	$FF			; INVERT SO 0=BUSY
+	AND	(IY+ESP_CFG_BSYMSK)	; IS ESP BUSY?
 	RET	Z			; RETURN IF BUSY
 	DJNZ	ESP_WTBSY1		; ELSE LOOP
 	OR	$FF			; SIGNAL TIMEOUT
@@ -178,9 +236,10 @@ ESP_WTBSY1:
 ESP_WTRDY:
 	LD	B,0			; MAX TRIES
 ESP_WTRDY1:
-	IN	A,(ESP_STAT)		; GET STATUS
-	AND	ESP_0_RDY		; IS ESP READY TO OUTPUT
-	XOR	ESP_0_RDY		; INVERT, 0=READY
+	LD	C,(IY+ESP_CFG_ST)	; ESP STATUS PORT
+	IN	A,(C)			; GET STATUS
+	XOR	$FF			; INVERT SO 0=READY
+	AND	(IY+ESP_CFG_RDYMSK)	; IS ESP READY TO OUTPUT
 	RET	Z			; RETURN IF READY
 	DJNZ	ESP_WTRDY1		; ELSE LOOP
 	OR	$FF			; SIGNAL TIMEOUT
@@ -188,8 +247,10 @@ ESP_WTRDY1:
 ;
 ;
 ;
-ESP_STR_NOHW		.TEXT	" NOT PRESENT$"
-ESP_STR_UPGRADE		.TEXT	" !!!UPGRADE REQUIRED!!!$"
+ESP_PRES		.DB	0	; MODULE PRESENCE BITS
+;
+ESP_STR_NOHW		.TEXT	"NOT PRESENT$"
+ESP_STR_UPGRADE		.TEXT	"!!!UPGRADE REQUIRED!!!$"
 ;
 ;==================================================================================================
 ; ESP32 CONSOLE DRIVER
@@ -202,9 +263,26 @@ ESPCON_COLS	.EQU	80		; VGA DISPLAY COLS
 ;
 ;
 ESPCON_INIT:
+	LD	A,(ESPCON_DEVCNT)	; GET ESPCON PHYSICAL DEVICE COUNT
+	LD	(IY+ESP_CFG_DEV),A	; SAVE PHYSICAL UNIT NUMBER
+	INC	A			; UPDATE COUNT
+	LD	(ESPCON_DEVCNT),A	; SAVE COUNT
 ;
-	CALL	NEWLINE
-	PRTS("ESPCON:$")
+; ADD OURSELVES TO CIO DISPATCH TABLE
+;
+	LD	BC,ESPCON_FNTBL		; BC := FUNCTION TABLE ADDRESS
+	PUSH	IY			; COPY CONFIG ENTRY PTR
+	POP	DE			; ... TO DE
+	CALL	CIO_ADDENT		; ADD ENTRY, A := UNIT ASSIGNED
+	LD	(HCB + HCB_CRTDEV),A	; SET OURSELVES AS THE CRT DEVICE
+;
+; ANNOUNCE OURSLEVES
+;
+	CALL	NEWLINE			; FORMATTING
+	PRTS("ESPCON$")			; NAME
+	LD	A,(IY+ESP_CFG_DEV)	; GET PHYSICAL UNIT NUMBER
+	CALL	PRTDECB			; UNIT STILL IN A FROM ABOVE
+	CALL	PC_COLON		; FORMATTING
 ;
 	; DISPLAY CONSOLE DIMENSIONS
 	CALL	PC_SPACE
@@ -216,14 +294,6 @@ ESPCON_INIT:
 	CALL	PRTDECB
 	CALL	PRTSTRD
 	.TEXT	" TEXT (ANSI)$"
-;
-; ADD OURSELVES TO CIO DISPATCH TABLE
-;
-	LD	D,0			; PHYSICAL UNIT IS ZERO
-	LD	E,CIODEV_ESPCON		; DEVICE TYPE
-	LD	BC,ESPCON_FNTBL		; BC := FUNCTION TABLE ADDRESS
-	CALL	CIO_ADDENT		; ADD ENTRY, A := UNIT ASSIGNED
-	LD	(HCB + HCB_CRTDEV),A	; SET OURSELVES AS THE CRT DEVICE
 ;
 	XOR	A			; SIGNAL SUCCESS
 	RET
@@ -247,7 +317,7 @@ ESPCON_FNTBL:
 ESPCON_IN:
 	CALL	ESPCON_IST
 	JR	Z,ESPCON_IN
-	LD	A,ESP_CMD_KIN		; KBD INPUT
+	LD	A,ESP_0_CMD_KIN		; KBD INPUT
 	CALL	ESP_OUT			; SEND CMD OPCODE
 	CALL	ESP_INWAIT		; GET KEY
 	LD	E,A			; PUT IN E
@@ -257,7 +327,7 @@ ESPCON_IN:
 ;
 ;
 ESPCON_IST:
-	LD	A,ESP_CMD_KST		; KBD BUF STATUS
+	LD	A,ESP_0_CMD_KST		; KBD BUF STATUS
 	CALL	ESP_OUT			; SEND CMD OPCODE
 	CALL	ESP_INWAIT		; GET BUF SIZE
 	OR	A			; SET FLAGS
@@ -269,7 +339,7 @@ ESPCON_IST:
 ;
 ESPCON_OUT:
 	PUSH	DE
-	LD	A,ESP_CMD_COUT		; CHAR OUT OPCODE
+	LD	A,ESP_0_CMD_COUT	; CHAR OUT OPCODE
 	CALL	ESP_OUT
 	POP	DE
 	LD	A,E
@@ -280,7 +350,8 @@ ESPCON_OUT:
 ;
 ;
 ESPCON_OST:
-	OR	$FF			; SIGNAL OUTPUT QUEUE READY
+	XOR	A			; ZERO ACCUM
+	INC	A			; ACCUM := 1 TO SIGNAL 1 BUFFER POSITION
 	RET				; RETURN
 ;
 ;
@@ -301,14 +372,239 @@ ESPCON_QUERY:
 ;
 ESPCON_DEVICE:
 	LD	D,CIODEV_ESPCON		; D := DEVICE TYPE
-	LD	E,0			; E := DEVICE NUM, ALWAYS 0
+	LD	E,(IY+ESP_CFG_DEV)	; E := DEVICE NUM
 	LD	C,$BF			; C := DEVICE TYPE, 0xBF IS PROP TERM
 	LD	H,0			; H := 0, DRIVER HAS NO MODES
-	LD	L,ESP_IOBASE		; L := BASE I/O ADDRESS
+	LD	L,(IY+ESP_CFG_IO)	; L := BASE I/O ADDRESS
 	XOR	A			; SIGNAL SUCCESS
 	RET
 ;
-;=============================================================================
-; DATA STORAGE
-;=============================================================================
+; ESPCON CONFIGURATION
 ;
+ESPCON_CFG:
+ESPCON0_CFG:
+	.DB	0				; DEVICE NUMBER (UPDATED DURING INIT)
+	.DB	ESP_0_IO			; ESP DATA PORT
+	.DB	ESP_STAT			; ESP STATUS PORT
+	.DB	ESP_0_RDY			; ESP READY BIT MASK
+	.DB	ESP_0_BUSY			; ESP BUSY BIT MASK
+;
+;
+;
+ESPCON_DEVCNT	.DB	0			; ESPCON DEVICES COUNT
+;
+;==================================================================================================
+; ESP32 SERIAL DRIVER
+;==================================================================================================
+;
+ESPSER_LINECFG		.EQU	SER_115200_8N1
+;
+ESPSER_CFG_LINE		.EQU	5
+;
+;
+;
+ESPSER_INIT:
+	LD	A,(ESPSER_DEVCNT)	; GET ESPSER PHYSICAL DEVICE COUNT
+	LD	(IY+ESP_CFG_DEV),A	; SAVE PHYSICAL UNIT NUMBER
+	INC	A			; UPDATE COUNT
+	LD	(ESPSER_DEVCNT),A	; SAVE COUNT
+;
+; ADD OURSELVES TO CIO DISPATCH TABLE
+;
+	LD	BC,ESPSER_FNTBL		; BC := FUNCTION TABLE ADDRESS
+	PUSH	IY			; COPY CONFIG ENTRY PTR
+	POP	DE			; ... TO DE
+	CALL	CIO_ADDENT		; ADD ENTRY, A := UNIT ASSIGNED
+;
+; ANNOUNCE OURSLEVES
+;
+	CALL	NEWLINE			; FORMATTING
+	PRTS("ESPSER$")			; NAME
+	LD	A,(IY+ESP_CFG_DEV)	; GET PHYSICAL UNIT NUMBER
+	CALL	PRTDECB			; UNIT STILL IN A FROM ABOVE
+	CALL	PC_COLON		; FORMATTING
+;
+	PRTS(" MODE=$")				; FORMATTING
+	LD	E,(IY+ESPSER_CFG_LINE+0)	; FIRST CONFIG BYTE TO E
+	LD	D,(IY+ESPSER_CFG_LINE+1)	; SECOND CONFIG BYTE TO D
+	CALL	PS_PRTSC0			; PRINT CONFIG
+;
+; TODO: PRINT SERIAL CONFIG
+;
+	XOR	A			; SIGNAL SUCCESS
+	RET
+;
+; DRIVER FUNCTION TABLE
+;
+ESPSER_FNTBL:
+	.DW	ESPSER_IN
+	.DW	ESPSER_OUT
+	.DW	ESPSER_IST
+	.DW	ESPSER_OST
+	.DW	ESPSER_INITDEV
+	.DW	ESPSER_QUERY
+	.DW	ESPSER_DEVICE
+#IF (($ - ESPSER_FNTBL) != (CIO_FNCNT * 2))
+	.ECHO	"*** INVALID ESPSER FUNCTION TABLE ***\n"
+#ENDIF
+;
+;
+;
+ESPSER_IN:
+	CALL	ESPSER_IST
+	JR	Z,ESPSER_IN
+	LD	A,ESP_CMD_SIN		; SERIAL INPUT
+	CALL	ESP_OUT			; SEND CMD OPCODE
+	CALL	ESP_INWAIT		; GET KEY
+	LD	E,A			; PUT IN E
+	XOR	A			; SIGNAL SUCCES
+	RET				; AND DONE
+;
+;
+;
+ESPSER_IST:
+	LD	A,ESP_CMD_SST		; SERIAL STATUS
+	CALL	ESP_OUT			; SEND CMD OPCODE
+	CALL	ESP_INWAIT		; GET BUF SIZE
+	OR	A			; SET FLAGS
+	RET	Z			; AND DONE
+	OR	A
+	RET
+;
+;
+;
+ESPSER_OUT:
+	PUSH	DE
+	LD	A,ESP_CMD_SOUT		; CHAR OUT OPCODE
+	CALL	ESP_OUT
+	POP	DE
+	LD	A,E
+	CALL	ESP_OUT			; SEND CHAR VALUE
+	XOR	A			; SIGNAL SUCCESS
+	RET
+;
+;
+;
+ESPSER_OST:
+	XOR	A			; ZERO ACCUM
+	INC	A			; ACCUM := 1 TO SIGNAL 1 BUFFER POSITION
+	RET				; RETURN
+;
+;
+;
+ESPSER_INITDEV:
+	PUSH	DE			; SAVE INCOMING CONFIG WORD
+;
+	; XLATE NEW LINE MODE INTO C
+	LD	A,E
+	AND	%00111111		; ISOLATE MODE BITS
+	LD	C,0			; 8N1 = 0
+	CP	SER_DATA8 | SER_PARNONE | SER_STOP1
+	JR	Z,ESPSER_INITDEV1	; IF MATCH, DO IT
+	INC	C			; 8E1 = 1
+	CP	SER_DATA8 | SER_PAREVEN | SER_STOP1
+	JR	Z,ESPSER_INITDEV1	; IF MATCH, DO IT
+	INC	C			; 8O1 = 2
+	CP	SER_DATA8 | SER_PARODD | SER_STOP1
+	JR	Z,ESPSER_INITDEV1	; IF MATCH, DO IT
+	INC	C			; 7N1 = 3
+	CP	SER_DATA7 | SER_PARNONE | SER_STOP1
+	JR	Z,ESPSER_INITDEV1	; IF MATCH, DO IT
+	INC	C			; 7E1 = 4
+	CP	SER_DATA7 | SER_PAREVEN | SER_STOP1
+	JR	Z,ESPSER_INITDEV1	; IF MATCH, DO IT
+	INC	C			; 7O1 = 5
+	CP	SER_DATA7 | SER_PARODD | SER_STOP1
+	JR	Z,ESPSER_INITDEV1	; IF MATCH, DO IT
+	JR	NZ,ESPSER_INITDEV_ERR	; ELSE FAIL
+;
+ESPSER_INITDEV1:
+	; DECODE NEW BAUD RATE INTO DE:HL
+	LD	H,0
+	LD	A,D
+	AND	%00011111
+	LD	L,A
+	LD	DE,75
+	PUSH	BC			; SAVE NEW LINE MODE
+	CALL	DECODE			; DE:HL IS DECODED BAUD RATE
+	POP	BC			; RESTORE NEW LINE MODE
+	JR	NZ,ESPSER_INITDEV_ERR	; IF ERROR, FAIL
+;
+	; PROGRAM NEW LINE MODE
+	PUSH	BC
+	LD	A,ESP_CMD_SMODE
+	CALL	ESP_OUT
+	POP	BC
+	LD	A,C
+	;CALL	PRTHEXBYTE
+	;CALL	LDELAY
+	CALL	ESP_OUT
+;
+	; PROGRAM NEW BAUD RATE
+	LD	A,ESP_CMD_SBAUD
+	CALL	ESP_OUT
+	LD	A,L
+	CALL	ESP_OUT
+	LD	A,H
+	CALL	ESP_OUT
+	LD	A,E
+	CALL	ESP_OUT
+	LD	A,D
+	CALL	ESP_OUT
+;
+	; SAVE NEW LINE CONFIG WORD
+	POP	DE				; RESTORE CONFIG WORD
+	LD	(IY+ESPSER_CFG_LINE+0),E	; FIRST CONFIG BYTE
+	LD	(IY+ESPSER_CFG_LINE+1),D	; SECOND CONFIG BYTE
+;
+	XOR	A
+	RET
+;
+ESPSER_INITDEV_ERR:
+	POP	DE			; THROW AWAY CONFIG WORD ON STACK
+	OR	$FF
+	RET
+;
+;
+;
+ESPSER_QUERY:
+	LD	E,(IY+ESPSER_CFG_LINE+0)	; FIRST CONFIG BYTE TO E
+	LD	D,(IY+ESPSER_CFG_LINE+1)	; SECOND CONFIG BYTE TO D
+	LD	HL,0
+	XOR	A
+	RET
+;
+;
+;
+ESPSER_DEVICE:
+	LD	D,CIODEV_ESPSER		; D := DEVICE TYPE
+	LD	E,(IY+ESP_CFG_DEV)	; E := DEVICE NUM
+	LD	C,$00			; C := DEVICE TYPE, 0x00 IS RS-232
+	LD	H,0			; H := 0, DRIVER HAS NO MODES
+	LD	L,(IY+ESP_CFG_IO)	; L := BASE I/O ADDRESS
+	XOR	A			; SIGNAL SUCCESS
+	RET
+;
+; ESPSER CONFIGURATION
+;
+ESPSER_CFG:
+ESPSER0_CFG:
+	.DB	0				; DEVICE NUMBER (UPDATED DURING INIT)
+	.DB	ESP_0_IO			; ESP DATA PORT
+	.DB	ESP_STAT			; ESP STATUS PORT
+	.DB	ESP_0_RDY			; ESP READY BIT MASK
+	.DB	ESP_0_BUSY			; ESP BUSY BIT MASK
+	.DW	ESPSER_LINECFG			; LINE CONFIGURATION
+
+;
+ESPSER1_CFG:
+	.DB	0				; DEVICE NUMBER (UPDATED DURING INIT)
+	.DB	ESP_1_IO			; ESP DATA PORT
+	.DB	ESP_STAT			; ESP STATUS PORT
+	.DB	ESP_1_RDY			; ESP READY BIT MASK
+	.DB	ESP_1_BUSY			; ESP BUSY BIT MASK
+	.DW	ESPSER_LINECFG			; LINE CONFIGURATION
+;
+;
+;
+ESPSER_DEVCNT	.DB	0			; ESPSER DEVICES COUNT
--- a/Source/HBIOS/fd.asm
+++ b/Source/HBIOS/fd.asm
@@ -811,19 +811,27 @@ FD_DETECT:
 	IN	A,(FDC_MSR)	; READ MSR
 	;CALL	PC_SPACE	; *DEBUG*
 	;CALL	PRTHEXBYTE	; *DEBUG*
-	CP	$80
-	JR	Z,FD_DETECT1	; $80 IS OK
-	CP	$D0
-	JR	Z,FD_DETECT1	; $D0 IS OK
-	RET			; NOPE, ABORT WITH ZF=NZ
-;
-FD_DETECT1:
-	CALL	DLY32		; WAIT A BIT FOR FDC
-	IN	A,(FDC_MSR)	; READ MSR AGAIN
+	
+	CP	$D0		; SPECIAL CASE: DATA PENDING?
+	JR	NZ,FD_DETECT1	; NOPE, MOVE ALONG
+	IN	A,(FDC_DATA)	; SWALLOW THE PENDING DATA
+	CALL	DLY32		; SETTLE
+	IN	A,(FDC_MSR)	; ... AND REREAD THE STATUS
 	;CALL	PC_SPACE	; *DEBUG*
 	;CALL	PRTHEXBYTE	; *DEBUG*
-	CP	$80
-	RET			; $80 OK, ELSE NOT PRESENT
+
+FD_DETECT1:
+	CP	$80		; WE EXPECT $80
+	RET	Z		; IF SO, ALL DONE
+
+	; WE HAVE SEEN AN FDC THAT NEEDS A SECOND READ TO GET
+	; DESIRED VALUE, SO TRY ONE MORE TIME
+	CALL	DLY32		; WAIT A BIT
+	IN	A,(FDC_MSR)	; ... AND REREAD THE STATUS
+	;CALL	PC_SPACE	; *DEBUG*
+	;CALL	PRTHEXBYTE	; *DEBUG*
+	CP	$80		; CHECK FOR CORRECT VALUE
+	RET			; RETURN WITH ZF ACCORDING TO RESULT
 ;
 ; UNIT INITIALIZATION
 ;
--- a/Source/HBIOS/hbios.asm
+++ b/Source/HBIOS/hbios.asm
@@ -2148,11 +2148,40 @@ HB_CPU3:
 	LD	HL,HB_TIMINT
 	CALL	HB_ADDIM1		; ADD TO IM1 CALL LIST
    #ENDIF
-
+;
  #ENDIF
 ;
 #ENDIF
 ;
+; TEMPLATE FOR SETTING UP INTERRUPTS USING THE MBC/DUODYNE IM2 INTERRUPT
+; PIN HEADERS. UPDATE HB_DUMMYx TO POINT TO THE INTERRUPT ROUTINE.
+; IN STD.ASM ALLOCATE THE EQUIVALENT INT_IM2PHx INTERRUPT TABLE ENTRY NUMBER. 
+;
+;
+;	LD	HL,HB_DUMMY0
+;	LD	(IVT(INT_IM2PH0)),HL
+;
+;	LD	HL,HB_DUMMY1
+;	LD	(IVT(INT_IM2PH1)),HL
+;
+;	LD	HL,HB_DUMMY2
+;	LD	(IVT(INT_IM2PH2)),HL
+;
+;	LD	HL,HB_DUMMY3
+;	LD	(IVT(INT_IM2PH3)),HL
+;
+;	LD	HL,HB_DUMMY4
+;	LD	(IVT(INT_IM2PH4)),HL
+;
+;	LD	HL,HB_DUMMY5
+;	LD	(IVT(INT_IM2PH5)),HL
+;
+;	LD	HL,HB_DUMMY6
+;	LD	(IVT(INT_IM2PH6)),HL
+;
+;	LD	HL,HB_DUMMY7
+;	LD	(IVT(INT_IM2PH7)),HL
+;
 #IF (KIOENABLE)
 	CALL	KIO_PREINIT
 #ENDIF
@@ -7390,6 +7419,7 @@ PS_SDDUART	.TEXT	"DUART$"
 PS_SDZ2U	.TEXT	"Z2U$"
 PS_SDLPT	.TEXT	"LPT$"
 PS_SDESPCON	.TEXT	"ESPCON$"
+PS_SDESPSER	.TEXT	"ESPSER$"
 ;
 ; CHARACTER SUB TYPE STRINGS
 ;
--- a/Source/HBIOS/hbios.inc
+++ b/Source/HBIOS/hbios.inc
@@ -314,6 +314,7 @@ CIODEV_DUART	.EQU	$90
 CIODEV_Z2U	.EQU	$A0
 CIODEV_LPT	.EQU	$B0
 CIODEV_ESPCON	.EQU	$C0
+CIODEV_ESPSER	.EQU	$D0
 ;
 ; SUB TYPES OF CHAR DEVICES
 ;
--- a/Source/HBIOS/std.asm
+++ b/Source/HBIOS/std.asm
@@ -758,15 +758,30 @@ INT_SIO1	.EQU	14	; ZILOG SIO 1, CHANNEL A & B
 #ENDIF

 #IF ((CPUFAM == CPU_Z80) & (INTMODE == 2))
-  #IF (PLATFORM == PLT_MBC)

-; MBC Z80
+  #IF (PLATFORM == PLT_MBC)
+;
+; MBC IM2 PINHEADER INTERRUPTS
+;
+;INT_IM2PH0	.EQU	0	
+;INT_IM2PH1	.EQU	1
+;INT_IM2PH2	.EQU	2
+;INT_IM2PH3	.EQU	3
+;INT_IM2PH4	.EQU	4
+;INT_IM2PH5	.EQU	5
+;INT_IM2PH6	.EQU	6
+;INT_IM2PH7	.EQU	7
+;
+; MBC Z80 INTERRUPTS
+;
 ;INT_CTC0A	.EQU	0	; ZILOG CTC 0, CHANNEL A
 ;INT_CTC0B	.EQU	1	; ZILOG CTC 0, CHANNEL B
 ;INT_CTC0C	.EQU	2	; ZILOG CTC 0, CHANNEL C
 ;INT_CTC0D	.EQU	3	; ZILOG CTC 0, CHANNEL D
 INT_UART0	.EQU	4	; UART 0
 INT_UART1	.EQU	5	; UART 1
+INT_INT6	.EQU	6	;
+INT_INT7	.EQU	7	;
 INT_SIO0	.EQU	8	; ZILOG SIO 0, CHANNEL A & B
 INT_SIO1	.EQU	9	; ZILOG SIO 1, CHANNEL A & B
 INT_CTC0A	.EQU	12	; ZILOG CTC 0, CHANNEL A
@@ -778,9 +793,42 @@ INT_CTC0D	.EQU	15	; ZILOG CTC 0, CHANNEL D
 ;INT_PIO1A	.EQU	11	; ZILOG PIO 1, CHANNEL A
 ;INT_PIO1B	.EQU	12	; ZILOG PIO 1, CHANNEL B

-  #ELSE
+  #ENDIF
+
+  #IF (PLATFORM == PLT_DUO)
+
+; DUO IM2 PINHEADER INTERRUPTS
+
+;INT_IM2PH0	.EQU	0
+;INT_IM2PH1	.EQU	1
+;INT_IM2PH2	.EQU	2
+;INT_IM2PH3	.EQU	3
+;INT_IM2PH4	.EQU	4
+;INT_IM2PH5	.EQU	5
+;INT_IM2PH6	.EQU	6
+;INT_IM2PH7	.EQU	7
+;
+; DUO Z80 IM2 INTERRUPTS
+; 
+INT_UART0	.EQU	7	; UART 0
+INT_UART1	.EQU	6	; UART 1 ?????
+INT_CTC0A	.EQU	0	; ZILOG CTC 0, CHANNEL A
+INT_CTC0B	.EQU	1	; ZILOG CTC 0, CHANNEL B
+INT_CTC0C	.EQU	2	; ZILOG CTC 0, CHANNEL C
+INT_CTC0D	.EQU	3	; ZILOG CTC 0, CHANNEL D
+;INT_SIO0	.EQU	7	; ZILOG SIO 0, CHANNEL A & B
+INT_SIO1	.EQU	8	; ZILOG SIO 1, CHANNEL A & B
+INT_PIO0A	.EQU	9	; ZILOG PIO 0, CHANNEL A
+INT_PIO0B	.EQU	10	; ZILOG PIO 0, CHANNEL B
+INT_PIO1A	.EQU	11	; ZILOG PIO 1, CHANNEL A
+INT_PIO1B	.EQU	12	; ZILOG PIO 1, CHANNEL B
+
+  #ENDIF
+
+  #IF ((PLATFORM != PLT_MBC) & (PLATFORM != PLT_DUO))
+
+; GENERIC Z80 M2 INTERRUPTS

-; GENERIC Z80
 INT_CTC0A	.EQU	0	; ZILOG CTC 0, CHANNEL A
 INT_CTC0B	.EQU	1	; ZILOG CTC 0, CHANNEL B
 INT_CTC0C	.EQU	2	; ZILOG CTC 0, CHANNEL C
@@ -794,7 +842,8 @@ INT_PIO0B	.EQU	10	; ZILOG PIO 0, CHANNEL B
 INT_PIO1A	.EQU	11	; ZILOG PIO 1, CHANNEL A
 INT_PIO1B	.EQU	12	; ZILOG PIO 1, CHANNEL B

-    #ENDIF
+  #ENDIF
+
 #ENDIF

 #DEFINE IVT(INTX) HB_IVT+(INTX * 4)+1
--- a/Source/HBIOS/uart.asm
+++ b/Source/HBIOS/uart.asm
@@ -53,13 +53,16 @@ UART_INTACT		.EQU	7	; INT RCV ACTIVE BIT
 UART_FIFOACT		.EQU	6	; FIFO ACTIVE BIT
 UART_AFCACT		.EQU	5	; AUTO FLOW CONTROL ACTIVE BIT
 ;
+#IF (PLATFORM == PLT_DUO)
+UARTSBASE		.EQU	$58
+#ELSE
 UARTSBASE		.EQU	$68
+#ENDIF
 UARTCBASE		.EQU	$80
 UARTMBASE		.EQU	$18
 UART4BASE		.EQU	$C0
 UARTRBASE		.EQU	$A0
 UARTDBASE		.EQU	$80
-UARTYBASE		.EQU	$58
 ;
 #IF (UARTINTS)
 ;
@@ -1088,16 +1091,6 @@ UART_CFG_MFP:
 	.DW	UARTCFG				; LINE CONFIGURATION
 	.DW	0				; SHOULD NEVER NEED INT HANDLER
 #ENDIF
-#IF (UARTDUO)
-UART_CFG_DUO:
-	; DUODYNE ONBOARD SERIAL PORT
-	.DB	0				; DEVICE NUMBER (UPDATED DURING INIT)
-	.DB	0				; UART TYPE
-	.DB	UARTYBASE			; IO PORT BASE (RBR, THR)
-	.DB	UARTYBASE + UART_LSR		; LINE STATUS PORT (LSR)
-	.DW	UARTCFG				; LINE CONFIGURATION
-	.DW	0				; POINTER TO RCV BUFFER STRUCT
-#ENDIF
 ;
 UART_CNT	.EQU	($ - UART_CFG) / 8
 ;
--- a/Source/ver.inc
+++ b/Source/ver.inc
@@ -2,7 +2,7 @@
 #DEFINE	RMN	3
 #DEFINE	RUP	0
 #DEFINE	RTP	0
-#DEFINE BIOSVER	"3.3.0-dev.43"
+#DEFINE BIOSVER	"3.3.0-dev.48"
 #define rmj	RMJ
 #define rmn	RMN
 #define rup	RUP
--- a/Source/ver.lib
+++ b/Source/ver.lib
@@ -3,5 +3,5 @@ rmn	equ	3
 rup	equ	0
 rtp	equ	0
 biosver	macro
-	db	"3.3.0-dev.43"
+	db	"3.3.0-dev.48"
 	endm
Author	SHA1	Message	Date
Wayne Warthen	8b7e71049b	FDC Detection Update & Enable ESP Driver on Duodyne - Based on reports from Martin R, the FDC detection algorithm has been updated to try reading the FDC MSR register twice to try and get the desired value of 0x80. - Dan Werner's ESP board for Duodyne is working well, so the default Duodyne config has been changed to automatically detect this board.	2023-08-25 10:25:07 -07:00
Wayne Warthen	50e190c755	Merge pull request #357 from fernandocarolo/dev Fix references to the EPFDC driver in comments.	2023-08-23 14:44:47 -07:00
Wayne Warthen	d0eccf026b	Enable INTRTC for Easy Z80	2023-08-23 14:28:20 -07:00
Fernando Carolo	39f796ce22	Fix references to the EPFDC driver in comments. The EtchedPixels floppy disk controller is known by the identifier 'FDMODE_EPFDC', but the comments in the Config subdirectory have an incorrect reference to 'EPWDC'. This fix updates the comments to use the correct name.	2023-08-23 21:02:48 +01:00
Wayne Warthen	5610e79db4	Improve FD Driver Detection Credit to Martin R for reporting that his FDC was not being detected. The delay between FDC status register reads was increased in the detection routine to correct this.	2023-08-22 15:22:11 -07:00
Wayne Warthen	e782b78b16	Bump Version	2023-08-22 11:02:08 -07:00
Wayne Warthen	c0d3969244	Merge pull request #356 from b1ackmai1er/dev Duo/MBC IM2 Hardware Timer support	2023-08-22 10:54:30 -07:00
b1ackmai1er	c62af3df33	MBC / DUO IM2 template Template for setting up interrupts using the IM2 pin header on MBC and DUO platforms.	2023-08-22 13:16:42 +08:00
b1ackmai1er	6d736996fd	Merge pull request #60 from wwarthen/dev Support Serial Ports on ESP32 Board	2023-08-22 12:32:56 +08:00
Wayne Warthen	8bc801d0a4	Support Serial Ports on ESP32 Board	2023-08-21 17:40:34 -07:00
b1ackmai1er	2c6b7f7fb1	Update std.asm	2023-08-21 16:38:59 +08:00
b1ackmai1er	c3503f56d1	Update cfg_z80retro.asm	2023-08-21 16:29:27 +08:00
b1ackmai1er	d4c87996f0	Merge branch 'dev' of https://github.com/b1ackmai1er/RomWBW into dev	2023-08-21 16:25:29 +08:00
b1ackmai1er	9f5b3a8b1c	Duo/MBC IM2 Hardware Timer support	2023-08-21 16:00:47 +08:00
Wayne Warthen	d06e1e2a5c	Initial DUO Interrupt Handling	2023-08-20 15:03:34 -07:00