Miscellaneous

- Minor correction to DMAMON to restore proper operation of interrupt testing
- Minor improvements to QPM documentation

Doc/ChangeLog.txt

@@ -19,6 +19,7 @@ Version 3.3
 - WBW: Early support for Duodyne base system (CPU/UART/ROM/RAM/RTC/SPK)
 - M?C: Fixed XM to allow specifying HBIOS port for send operations
 - WBW: Fix S100 Z180 LED operation (credit to Jay Cotton for finding this issue)
+- WBW: QPM system image is now combined with current CBIOS during build
 
 Version 3.2.1
 -------------

ReadMe.md

@@ -3,7 +3,7 @@
 **RomWBW ReadMe** \
 Version 3.3 \
 Wayne Warthen  ([wwarthen@gmail.com](mailto:wwarthen@gmail.com)) \
-08 Aug 2023
+10 Sep 2023
 
 # Overview
 

ReadMe.txt

@@ -1,6 +1,6 @@
 RomWBW ReadMe
 Wayne Warthen (wwarthen@gmail.com)
-08 Aug 2023
+10 Sep 2023
 
 
 

Source/Apps/FDU/fdu.doc

@@ -153,7 +153,8 @@ JP2 (/FAULT) shorted, JP3 (MINI): 2-3, JP4 (/DC/RDY): 2-3.
 
 The RCBus Scott Baker WDC-based floppy module should be jumpered
 for I/O base address 0x50 (SV1: 11-12), JP1 (/DACK): 1-2,
-JP2 (TC): 2-3.
+JP2 (TC): 2-3.  Note that pin 1 of JPX jumpers is toward the bottom
+of the board.
 
 The RCBus FDC by Alan Cox (Etched Pixels) needs to be strapped
 for base I/O address 0x48.

Source/Apps/Test/DMAmon/dmamon.asm

@@ -136,6 +136,8 @@ MAIN:
 	ld	de,$A000
 	ld	bc,hsiz
 	ldir
+	ld	a,(dmaport)
+	ld	(int_dmaport),a
 ;
 	; Install interrupt vector (RomWBW specific!!!)
 	ld	hl,int		; pointer to my interrupt handler
@@ -215,6 +217,9 @@ DMACFG_S:
 	call	HEXIN
 	ld	hl,dmaport
 	ld	(hl),a
+#IF (INTENABLE)
+	ld	(int_dmaport),a
+#ENDIF
 	jp	MENULP
 ;
 DMACFG_L:
@@ -1193,7 +1198,6 @@ CST:
 	RET
 ;
 USEINT	.DB	FALSE		; USE INTERRUPTS FLAG
-counter	.dw	0	
 dmaport	.db	DMABASE
 dmalach	.db	DMALATCH
 dmaxfer	.db	DMA_XMODE
@@ -1214,11 +1218,16 @@ reladr	.equ	$		; relocation start adr
 	.org	$A000		; code will run here
 ;
 int:
+	;LD	E,'.'			; OUTPUT CHAR TO E
+	;LD	C,CIO_CONSOLE		; CONSOLE UNIT TO C
+	;LD	B,BF_CIOOUT		; HBIOS FUNC: OUTPUT CHAR
+	;CALL	$FFF0			; HBIOS OUTPUTS CHARACTER
+
 	; According to the DMA doc, you must issue
 	; a DMA_DISABLE command prior to a
 	; DMA_REINIT_STATUS_BYTE command to avoid a
 	; potential race condition.
-	ld	a,(dmaport)
+	ld	a,(int_dmaport)
 	ld	c,a
 	ld	a,DMA_DISABLE
 	out	(c),a
@@ -1238,6 +1247,11 @@ int:
 	or	$ff		; signal int handled
 	ret
 ;
+; data referred to in handler must reside in high mem
+;
+int_dmaport	.db	0	; hi mem copy of dmaport
+counter		.dw	0	; interrupt counter
+;
 hsiz	.equ	$ - $A000	; size of handler to relocate
 ;
 	.org	reladr + hsiz

Source/Apps/Test/I2C/Build.cmd

@@ -8,6 +8,8 @@ set TASMTABS=%TOOLS%\tasm32
 tasm -t180 -g3 -fFF i2cscan.asm i2cscan.com i2cscan.lst || exit /b
 tasm -t180 -g3 -fFF rtcds7.asm rtcds7.com rtcds7.lst || exit /b
 tasm -t180 -g3 -fFF i2clcd.asm i2clcd.com i2clcd.lst || exit /b
+tasm -t80 -g3 -ff srom.asm srom.com srom.lst || exit /b
 
 copy /Y i2c*.com ..\..\..\..\Binary\Apps\Test\ || exit /b
 copy /Y rtcds7*.com ..\..\..\..\Binary\Apps\Test\ || exit /b
+copy /Y srom.com ..\..\..\..\Binary\Apps\Test\ || exit /b

Source/Apps/Test/I2C/Makefile

@@ -1,4 +1,4 @@
-OBJECTS = i2cscan.com rtcds7.com i2clcd.com
+OBJECTS = i2cscan.com rtcds7.com i2clcd.com srom.com
 DEST = ../../../../Binary/Apps/Test/
 TOOLS = ../../../../Tools
 

Source/BuildShared.cmd

@@ -4,6 +4,7 @@ setlocal
 pushd HDIAG && call Build || exit /b & popd
 pushd CBIOS && call Build || exit /b & popd
 pushd CPM22 && call Build || exit /b & popd
+pushd QPM && call Build || exit /b & popd
 pushd ZCPR && call Build || exit /b & popd
 pushd ZCPR-DJ && call Build || exit /b & popd
 pushd ZSDOS && call Build || exit /b & popd

Source/Clean.cmd

@@ -4,6 +4,7 @@ setlocal
 pushd HDIAG && call Clean.cmd & popd
 pushd Apps && call Clean.cmd & popd
 pushd CPM22 && call Clean.cmd & popd
+pushd QPM && call Clean.cmd & popd
 pushd ZCPR && call Clean.cmd & popd
 pushd ZCPR-DJ && call Clean.cmd & popd
 pushd ZSDOS && call Clean.cmd & popd

Source/Doc/UserGuide.md

@@ -2143,10 +2143,36 @@ regarding the RomWBW adaptation and customizations.
 
 #### Boot Disk
 
-There is no RomWBW-specific boot disk creation procedure.  QP/M
-comes with a QINSTALL which is used to install QPM over an existing
-CP/M 2 installation or to update an existing QPM disk.  `QINSTALL.COM`
-is included with the RomWBW distribution.
+
+To create or update a bootable QP/M Z-System disk, a special process
+is required.  QP/M is not provided in source format.  You are expected
+to install QP/M over an existing CP/M installation using the
+`QINSTALL.COM` application.
+
+To update an existing QP/M boot disk with the latest RomWBW CBIOS, you
+must use 2 steps: apply the generic CP/M system track, then reinstall
+the QP/M components.  To do this, you can perform the following steps:
+
+1. Boot to the existing QP/M disk.  At this point, drive A should be
+   the QP/M disk that you wish to update.  You may receive a warning
+   about CBIOS/HBIOS version mismatch.
+
+1. Use RomWBW `SYSCOPY` to place the stock RomWBW CP/M OS image
+   onto the system tracks of the QP/M boot disk:
+   
+   `SYSCOPY A:=x:CPM.SYS`
+   
+   where x is the drive letter of your ROM Disk.
+
+1. Run `QINSTALL` to overlay the QP/M OS components on your
+   QP/M boot disk.
+
+**WARNING**: `QINSTALL` has no mechanism for retaining previous
+non-default settings.  Any previous non-default settings you
+previously made with `QINSTALL` will need to be reapplied.  The
+pre-built RomWBW QP/M disk image includes a couple of specific
+non-default settings to optimize use with RomWBW.  Please review the
+notes in the ReadMe.txt file in Source/Images/d_qpm.
 
 #### Notes
 
@@ -2154,6 +2180,9 @@ is included with the RomWBW distribution.
   on the QPM binary distribution and has been minimally customized
   for RomWBW.
 
+- When booted, the QPM startup banner will indicate CP/M 2.2.  This
+  is because QPM uses the CP/M 2.2 CBIOS code.
+
 - QINSTALL is used to customize QPM.  It is included on the
   disk image.  You should review the notes in the ReadMe.txt
   file in Source/Images/d_qpm before making changes.

Source/HBIOS/Config/DUO_std.asm

@@ -44,3 +44,5 @@ MDFFENABLE	.SET	FALSE		; MD: ENABLE FLASH FILE SYSTEM
 ;
 UARTINTS	.SET	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 ;UARTCFG	.SET	UARTCFG | SER_RTS
+;
+ESPENABLE	.SET	TRUE		; ESP: ENABLE ESP32 IO BOARD DRIVER (ESP.ASM)

Source/HBIOS/Config/MK4_std.asm

@@ -47,7 +47,7 @@ VGAENABLE	.SET	TRUE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VDAEMU_SERKBD	.SET	0		; VDA EMULATION: SERIAL KBD UNIT #, OR $FF FOR HW KBD
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_DIDE	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_DIDE	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/RCZ180_ext.asm

@@ -58,7 +58,7 @@ AYMODE		.SET	AYMODE_RCZ180	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LI
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/RCZ180_nat.asm

@@ -57,7 +57,7 @@ AYMODE		.SET	AYMODE_RCZ180	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LI
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/RCZ280_ext.asm

@@ -56,7 +56,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/RCZ280_nat.asm

@@ -56,7 +56,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/RCZ280_zz80mb.asm

@@ -62,7 +62,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/RCZ280_zzrc.asm

@@ -70,7 +70,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/RCZ80_easy.asm

@@ -41,6 +41,7 @@ WDOGIO		.SET	$6F		; WATCHDOG REGISTER ADR
 ;
 DSRTCENABLE	.SET	TRUE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
 RP5RTCENABLE	.SET	FALSE		; RP5C01 RTC BASED CLOCK (RP5RTC.ASM)
+INTRTCENABLE	.SET	TRUE		; ENABLE PERIODIC INTERRUPT CLOCK DRIVER (INTRTC.ASM)
 ;
 CTCENABLE	.SET	TRUE		; ENABLE ZILOG CTC SUPPORT
 CTCTIMER	.SET	TRUE		; ENABLE CTC PERIODIC TIMER
@@ -69,7 +70,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/RCZ80_jbl.asm

@@ -69,7 +69,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	TRUE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	FALSE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/RCZ80_kio.asm

@@ -66,7 +66,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/RCZ80_skz.asm

@@ -61,7 +61,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/RCZ80_std.asm

@@ -54,7 +54,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/RCZ80_tiny.asm

@@ -75,7 +75,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 IDE0BASE	.SET	$90		; IDE 0: IO BASE ADDRESS

Source/HBIOS/Config/RCZ80_zrc.asm

@@ -53,7 +53,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/RCZ80_zrc_ram.asm

@@ -57,7 +57,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/S100_std.asm

@@ -27,18 +27,17 @@
 #include "cfg_s100.asm"
 ;
 CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
+CRTACT		.SET	TRUE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
 ;
 Z180_CLKDIV	.SET	1		; Z180: CHK DIV: 0=OSC/2, 1=OSC, 2=OSC*2
-Z180_MEMWAIT	.SET	0		; Z180: MEMORY WAIT STATES (0-3)
-Z180_IOWAIT	.SET	1		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
+Z180_MEMWAIT	.SET	1		; Z180: MEMORY WAIT STATES (0-3)
+Z180_IOWAIT	.SET	2		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
 ;
 DSRTCENABLE	.SET	FALSE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
 INTRTCENABLE	.SET	TRUE		; ENABLE PERIODIC INTERRUPT CLOCK DRIVER (INTRTC.ASM)
 ;
-UARTENABLE	.SET	FALSE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 ASCIENABLE	.SET	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
-ACIAENABLE	.SET	FALSE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
-SIOENABLE	.SET	FALSE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
+SCONENABLE	.SET	TRUE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 IDEENABLE	.SET	FALSE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/SBC_std.asm

@@ -45,7 +45,7 @@ VGAENABLE	.SET	TRUE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VDAEMU_SERKBD	.SET	0		; VDA EMULATION: SERIAL KBD UNIT #, OR $FF FOR HW KBD
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_DIO3	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_DIO3	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	FALSE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/SCZ180_sc126.asm

@@ -59,7 +59,7 @@ AYMODE		.SET	AYMODE_RCZ180	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LI
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/SCZ180_sc130.asm

@@ -60,7 +60,7 @@ AYMODE		.SET	AYMODE_RCZ180	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LI
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/SCZ180_sc140.asm

@@ -54,7 +54,7 @@ AYMODE		.SET	AYMODE_LINC	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LINC
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/SCZ180_sc503.asm

@@ -54,7 +54,7 @@ AYMODE		.SET	AYMODE_LINC	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LINC
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)

Source/HBIOS/Config/ZETA2_std.asm

@@ -35,7 +35,7 @@ UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 UARTSBC		.SET	TRUE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_ZETA2	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_ZETA2	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 PPIDEENABLE	.SET	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)

Source/HBIOS/Config/ZETA_std.asm

@@ -35,7 +35,7 @@ UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 UARTSBC		.SET	TRUE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_ZETA	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_ZETA	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 PPIDEENABLE	.SET	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)

Source/HBIOS/cfg_duo.asm

@@ -167,6 +167,7 @@ TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VGASIZ		.EQU	V80X25		; VGA: DISPLAY FORMAT [V80X25|V80X30|V80X43]
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
@@ -236,6 +237,7 @@ PRPCONENABLE	.EQU	TRUE		; PRP: ENABLE PROPIO DRIVER VIDEO/KBD SUPPORT
 PPPENABLE	.EQU	FALSE		; PPP: ENABLE ZETA PARALLEL PORT PROPELLER BOARD DRIVER (PPP.ASM)
 ;
 ESPENABLE	.EQU	FALSE		; ESP: ENABLE ESP32 IO BOARD DRIVER (ESP.ASM)
+ESPCONENABLE	.EQU	TRUE		; ESP: ENABLE ESP32 CONSOLE IO DRIVER VIDEO/KBD SUPPORT
 ;
 HDSKENABLE	.EQU	FALSE		; HDSK: ENABLE SIMH HDSK DISK DRIVER (HDSK.ASM)
 HDSKTRACE	.EQU	1		; HDSK: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)

Source/HBIOS/cfg_dyno.asm

@@ -179,6 +179,7 @@ TMSMODE		.EQU	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MS
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK

Source/HBIOS/cfg_master.asm

@@ -236,6 +236,7 @@ TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VGASIZ		.EQU	V80X25		; VGA: DISPLAY FORMAT [V80X25|V80X30|V80X43]
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK

Source/HBIOS/cfg_mbc.asm

@@ -164,6 +164,7 @@ TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VGASIZ		.EQU	V80X25		; VGA: DISPLAY FORMAT [V80X25|V80X30|V80X43]
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK

Source/HBIOS/cfg_mk4.asm

@@ -175,6 +175,7 @@ TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VGASIZ		.EQU	V80X25		; VGA: DISPLAY FORMAT [V80X25|V80X30|V80X43]
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK

Source/HBIOS/cfg_n8.asm

@@ -177,6 +177,7 @@ TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VGASIZ		.EQU	V80X25		; VGA: DISPLAY FORMAT [V80X25|V80X30|V80X43]
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK

Source/HBIOS/cfg_rcz180.asm

@@ -185,6 +185,7 @@ TMSMODE		.EQU	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MS
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK

Source/HBIOS/cfg_rcz280.asm

@@ -189,6 +189,7 @@ TMSMODE		.EQU	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MS
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK

Source/HBIOS/cfg_rcz80.asm

@@ -183,6 +183,7 @@ TMSMODE		.EQU	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MS
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK

Source/HBIOS/cfg_rph.asm

@@ -166,6 +166,7 @@ TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VGASIZ		.EQU	V80X25		; VGA: DISPLAY FORMAT [V80X25|V80X30|V80X43]
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK

Source/HBIOS/cfg_s100.asm

@@ -46,8 +46,8 @@ MPGENA		.EQU	$7C		; Z2 MEM MGR PAGING ENABLE REGISTER (BIT 0, WRITE ONLY)
 ;
 Z180_BASE	.EQU	$C0		; Z180: I/O BASE ADDRESS FOR INTERNAL REGISTERS
 Z180_CLKDIV	.EQU	1		; Z180: CHK DIV: 0=OSC/2, 1=OSC, 2=OSC*2
-Z180_MEMWAIT	.EQU	0		; Z180: MEMORY WAIT STATES (0-3)
-Z180_IOWAIT	.EQU	1		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
+Z180_MEMWAIT	.EQU	1		; Z180: MEMORY WAIT STATES (0-3)
+Z180_IOWAIT	.EQU	2		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
 Z180_TIMER	.EQU	TRUE		; Z180: ENABLE Z180 SYSTEM PERIODIC TIMER
 ;
 RTCIO		.EQU	$0C		; RTC LATCH REGISTER ADR
@@ -125,7 +125,7 @@ DUART1BASE	.EQU	$40		; DUART 1: BASE ADDRESS OF CHIP
 DUART1ACFG	.EQU	DEFSERCFG	; DUART 1A: SERIAL LINE CONFIG
 DUART1BCFG	.EQU	DEFSERCFG	; DUART 1B: SERIAL LINE CONFIG
 ;
-UARTENABLE	.EQU	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+UARTENABLE	.EQU	FALSE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG | SER_RTS	; UART: LINE CONFIG FOR UART PORTS
@@ -148,7 +148,7 @@ Z2UENABLE	.EQU	FALSE		; Z2U: ENABLE Z280 UART SERIAL DRIVER (Z2U.ASM)
 ;
 ACIAENABLE	.EQU	FALSE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
 ;
-SIOENABLE	.EQU	TRUE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
+SIOENABLE	.EQU	FALSE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
 SIODEBUG	.EQU	FALSE		; SIO: ENABLE DEBUG OUTPUT
 SIOBOOT		.EQU	0		; SIO: REBOOT ON RCV CHAR (0=DISABLED)
 SIOCNT		.EQU	2		; SIO: NUMBER OF CHIPS TO DETECT (1-2), 2 CHANNELS PER CHIP
@@ -179,6 +179,7 @@ TMSMODE		.EQU	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MS
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK

Source/HBIOS/cfg_sbc.asm

@@ -164,6 +164,7 @@ TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VGASIZ		.EQU	V80X25		; VGA: DISPLAY FORMAT [V80X25|V80X30|V80X43]
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK

Source/HBIOS/cfg_scz180.asm

@@ -179,6 +179,7 @@ TMSMODE		.EQU	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MS
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK

Source/HBIOS/cfg_z80retro.asm

@@ -166,6 +166,7 @@ TMSMODE		.EQU	TMSMODE_NONE	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|M
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK

Source/HBIOS/cfg_zeta.asm

@@ -136,6 +136,7 @@ TMSMODE		.EQU	TMSMODE_NONE	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|M
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK

Source/HBIOS/cfg_zeta2.asm

@@ -147,6 +147,7 @@ TMSMODE		.EQU	TMSMODE_NONE	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|M
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK

Source/HBIOS/esp.asm

@@ -8,7 +8,7 @@
 ;
 ; TODO:
 ; - CLEAR CONSOLE SCREEN AT INITIALIZATION
-; - INITIALIZE BAUD/MODE OF SERIAL INTERFACES AT INITIALIZATION
+; - INITIALIZE BAUD/MODE OF SERIAL INTERFACES AT INITIALIZATION?
 ;
 ESP_IOBASE	.EQU	$9C
 ESP_0_IO	.EQU	ESP_IOBASE + 0
@@ -126,19 +126,52 @@ ESP_INIT6:
 ;==================================================================================================
 ;
 ESP_DETECT:
+	; TRY TO DETECT IF PORT IS FLOATING AND
+	; FAIL DETECTION IF SO
+	LD	C,(IY+ESP_CFG_ST)	; ESP STATUS PORT
+	IN	A,(C)			; READ IT
+	;CALL	PC_SPACE		; *DEBUG*
+	;CALL	PRTHEXBYTE		; *DEBUG*
+	AND	%11100000		; ISOLATE TOP 3 BITS
+	CP	$00			; ALWAYS ZERO IF PRESENT
+	RET	NZ			; ABORT ON FAILURE
+;
+	; ESP32 PROCESSOR MAY TAKE A FEW SECONDS TO START UP, SO
+	; HERE WE WAIT FOR BUSY TO CLEAR WITH ABOUT A 5 SECOND TIMEOUT
+	LD	B,0			; LOOP UP TO 256 TIMES
+	LD	C,(IY+ESP_CFG_ST)	; ESP STATUS PORT
+ESP_DETECT1:
+	IN	A,(C)			; GET STATUS
+	AND	(IY+ESP_CFG_BSYMSK)	; IS ESP BUSY?
+	JR	Z,ESP_DETECT2		; MOVE ALONG IF NOT BUSY
+	LD	DE,1500			; 1500 * 16US = 24MS
+	CALL	VDELAY			; DELAY
+	DJNZ	ESP_DETECT1		; LOOP
+	OR	$FF			; SIGNAL FAILURE
+	RET				; DONE
+;
+ESP_DETECT2:
+	;LD	A,B			; *DEBUG*
+	;CALL	PC_SPACE		; *DEBUG*
+	;CALL	PRTHEXBYTE		; *DEBUG*
 	CALL	ESP_CLR			; CLEAR ANY PENDING DATA
-	RET	NZ			; IF FAILS, ASSUME NOT PRESENT
 	LD	A,ESP_CMD_DISC		; DISCOVER COMMAND
 	CALL	ESP_OUT			; SEND IT
 ;
 	; LOOK FOR SIGNATURE STARTING WITH "ESP"
 	CALL	ESP_INWAIT		; ATTEMPT TO GET CHAR
+	;CALL	PC_SPACE		; *DEBUG*
+	;CALL	PRTHEXBYTE		; *DEBUG*
 	CP	'E'
 	RET	NZ
 	CALL	ESP_INWAIT		; ATTEMPT TO GET CHAR
+	;CALL	PC_SPACE		; *DEBUG*
+	;CALL	PRTHEXBYTE		; *DEBUG*
 	CP	'S'
 	RET	NZ
 	CALL	ESP_INWAIT		; ATTEMPT TO GET CHAR
+	;CALL	PC_SPACE		; *DEBUG*
+	;CALL	PRTHEXBYTE		; *DEBUG*
 	CP	'P'
 	RET
 ;
@@ -162,13 +195,14 @@ ESP_CLR0:
 ;
 ESP_PRTVER:
 	CALL	ESP_CLR			; CLEAR ANY PENDING DATA
+	;LD	DE,1000			; SMALL DELAY HERE
+	;CALL	VDELAY			; ... SEEMS TO HELP RELIABILITY
 	LD	A,ESP_CMD_DISC		; DISCOVER COMMAND
 	CALL	ESP_OUT			; SEND IT
 	CALL	ESP_WTRDY		; WAIT FOR READY TO OUTPUT
 ESP_PRTVER1:
 	CALL	ESP_WTNBSY		; WAIT TILL NOT BUSY
 	IN	A,(ESP_STAT)		; GET STATUS
-	;AND	ESP_0_RDY		; ISOLATE OUTPUT READY BIT
 	AND	(IY+ESP_CFG_RDYMSK)	; ISOLATE OUTPUT READY BIT
 	RET	Z			; DONE IF NOTHING READY
 	CALL	ESP_IN			; GET NEXT CHAR
@@ -208,19 +242,29 @@ ESP_IN1:
 ;
 ESP_WTNBSY:
 	LD	B,0			; MAX TRIES
+	;PUSH	HL			; SAVE HL
+	;LD	HL,0			; MAX TRIES
 ESP_WTNBSY1:	
 	LD	C,(IY+ESP_CFG_ST)	; ESP STATUS PORT
 	IN	A,(C)			; GET STATUS
 	AND	(IY+ESP_CFG_BSYMSK)	; IS ESP BUSY?
 	RET	Z			; RETURN IF NOT BUSY
+	;JR	Z,ESP_WTNBSY_Z		; RETURN IF NOT BUSY
 	DJNZ	ESP_WTNBSY1		; ELSE LOOP
+	;DEC	HL			; DEC LOOP COUNTER
+	;LD	A,H			; CHECK FOR
+	;OR	L			; ... TIMEOUT
+	;JR	NZ,ESP_WTNBSY1		; LOOP AS NEEDED
+	CALL	PC_ASTERISK		; *DEBUG*
 	OR	$FF			; SIGNAL TIMEOUT
+;ESP_WTNBSY_Z:
+	;POP	HL			; RECOVER HL
 	RET				; AND RETURN
 ;
 ; WAIT FOR ESP TO BE BUSY
 ;
 ESP_WTBSY:
-	LD	B,20			; MAX TRIES
+	LD	B,3			; MAX TRIES
 ESP_WTBSY1:	
 	LD	C,(IY+ESP_CFG_ST)	; ESP STATUS PORT
 	IN	A,(C)			; GET STATUS
@@ -230,6 +274,27 @@ ESP_WTBSY1:
 	DJNZ	ESP_WTBSY1		; ELSE LOOP
 	OR	$FF			; SIGNAL TIMEOUT
 	RET				; AND RETURN
+;;;;
+;;;; WAIT FOR ESP TO BE READY TO OUTPUT
+;;;;
+;;;ESP_WTRDY:
+;;;	PUSH	HL			; SAVE HL
+;;;	LD	HL,0			; MAX TRIES
+;;;ESP_WTRDY1:
+;;;	LD	C,(IY+ESP_CFG_ST)	; ESP STATUS PORT
+;;;	IN	A,(C)			; GET STATUS
+;;;	XOR	$FF			; INVERT SO 0=READY
+;;;	AND	(IY+ESP_CFG_RDYMSK)	; IS ESP READY TO OUTPUT
+;;;	JR	Z,ESP_WTRDY_Z		; RETURN IF READY
+;;;	DEC	HL			; DEC LOOP COUNTER
+;;;	LD	A,H			; CHECK FOR
+;;;	OR	L			; ... TIMEOUT
+;;;	JR	NZ,ESP_WTRDY1		; LOOP AS NEEDED
+;;;	CALL	PC_PERIOD		; *DEBUG*
+;;;	OR	$FF			; SIGNAL TIMEOUT
+;;;ESP_WTRDY_Z:
+;;;	POP	HL			; RECOVER HL
+;;;	RET				; AND RETURN
 ;
 ; WAIT FOR ESP TO BE READY TO OUTPUT
 ;
@@ -242,6 +307,7 @@ ESP_WTRDY1:
 	AND	(IY+ESP_CFG_RDYMSK)	; IS ESP READY TO OUTPUT
 	RET	Z			; RETURN IF READY
 	DJNZ	ESP_WTRDY1		; ELSE LOOP
+	CALL	PC_PERIOD		; *DEBUG*
 	OR	$FF			; SIGNAL TIMEOUT
 	RET				; AND RETURN
 ;

Source/HBIOS/fd.asm

@@ -811,19 +811,27 @@ FD_DETECT:
 	IN	A,(FDC_MSR)	; READ MSR
 	;CALL	PC_SPACE	; *DEBUG*
 	;CALL	PRTHEXBYTE	; *DEBUG*
-	CP	$80
-	JR	Z,FD_DETECT1	; $80 IS OK
-	CP	$D0
-	JR	Z,FD_DETECT1	; $D0 IS OK
-	RET			; NOPE, ABORT WITH ZF=NZ
-;
-FD_DETECT1:
-	CALL	DLY32		; WAIT A BIT FOR FDC
-	IN	A,(FDC_MSR)	; READ MSR AGAIN
+	
+	CP	$D0		; SPECIAL CASE: DATA PENDING?
+	JR	NZ,FD_DETECT1	; NOPE, MOVE ALONG
+	IN	A,(FDC_DATA)	; SWALLOW THE PENDING DATA
+	CALL	DLY32		; SETTLE
+	IN	A,(FDC_MSR)	; ... AND REREAD THE STATUS
 	;CALL	PC_SPACE	; *DEBUG*
 	;CALL	PRTHEXBYTE	; *DEBUG*
-	CP	$80
-	RET			; $80 OK, ELSE NOT PRESENT
+
+FD_DETECT1:
+	CP	$80		; WE EXPECT $80
+	RET	Z		; IF SO, ALL DONE
+
+	; WE HAVE SEEN AN FDC THAT NEEDS A SECOND READ TO GET
+	; DESIRED VALUE, SO TRY ONE MORE TIME
+	CALL	DLY32		; WAIT A BIT
+	IN	A,(FDC_MSR)	; ... AND REREAD THE STATUS
+	;CALL	PC_SPACE	; *DEBUG*
+	;CALL	PRTHEXBYTE	; *DEBUG*
+	CP	$80		; CHECK FOR CORRECT VALUE
+	RET			; RETURN WITH ZF ACCORDING TO RESULT
 ;
 ; UNIT INITIALIZATION
 ;

Source/HBIOS/hbios.asm

@@ -1112,12 +1112,6 @@ Z280_BOOTERR	.TEXT	"\r\n\r\n*** Application mode boot not supported under Z280 n
 	DI				; NO INTERRUPTS
 	IM	1			; INTERRUPT MODE 1
 ;
-#IF ((PLATFORM == PLT_DUO) & FALSE)
-	; WAIT A WHILE
-	LD	B,0
-	DJNZ	$
-#ENDIF
-;
 #IF ((PLATFORM == PLT_DUO) & TRUE)
 	; WAIT A WHILE
 	LD	HL,0
@@ -2847,6 +2841,12 @@ HB_WDZ:
 	BIT	6,A			; BIT 6 HAS CONFIG JUMPER STATE
 	JR	Z,INITSYS3		; Z=SHORTED, BYPASS CONSOLE SWITCH
   #ENDIF
+;
+  #IF (PLATFORM == PLT_S100)
+	IN	A,($75)			; GET IO BYTE
+	AND	%00000001		; ISOLATE CONSOLE BIT
+	JR	NZ,INITSYS3		; NOT SET, BYPASS CONSOLE SWITCH
+  #ENDIF
 ;
 	LD	A,(CB_CRTDEV)		; GET CRT DISPLAY DEVICE
 	LD	(HB_NEWCON),A		; AND QUEUE TO SWITCH
@@ -3196,6 +3196,9 @@ HB_PCINITTBL:
 #IF (TMSENABLE)
 	.DW	TMS_PREINIT
 #ENDIF
+#IF (SCONENABLE)
+	.DW	SCON_PREINIT
+#ENDIF
 HB_PCINITTBLLEN	.EQU	(($ - HB_PCINITTBL) / 2)
 
 ;==================================================================================================
@@ -3300,6 +3303,9 @@ HB_INITTBL:
 #IF (TMSENABLE)
 	.DW	TMS_INIT
 #ENDIF
+#IF (SCONENABLE)
+	.DW	SCON_INIT
+#ENDIF
 #IF (VRCENABLE)
 	.DW	VRC_INIT
 #ENDIF
@@ -6361,12 +6367,21 @@ SIZ_VDU		.EQU	$ - ORG_VDU
 #IF (TMSENABLE)
 ORG_TMS		.EQU	$
   #INCLUDE "tms.asm"
-SIZ_TMS		.EQU	$ - ORG_TMS
+SIZ_TMS	.EQU	$ - ORG_TMS
 		.ECHO	"TMS occupies "
 		.ECHO	SIZ_TMS
 		.ECHO	" bytes.\n"
 #ENDIF
 ;
+#IF (SCONENABLE)
+ORG_SCON		.EQU	$
+  #INCLUDE "scon.asm"
+SIZ_SCON	.EQU	$ - ORG_SCON
+		.ECHO	"SCON occupies "
+		.ECHO	SIZ_SCON
+		.ECHO	" bytes.\n"
+#ENDIF
+;
 #IF (GDCENABLE)
 ORG_GDC	.EQU	$
   #INCLUDE "gdc.asm"
@@ -7420,6 +7435,7 @@ PS_SDZ2U	.TEXT	"Z2U$"
 PS_SDLPT	.TEXT	"LPT$"
 PS_SDESPCON	.TEXT	"ESPCON$"
 PS_SDESPSER	.TEXT	"ESPSER$"
+PS_SDSCON	.TEXT	"SCON$"
 ;
 ; CHARACTER SUB TYPE STRINGS
 ;

Source/HBIOS/hbios.inc

@@ -315,6 +315,7 @@ CIODEV_Z2U	.EQU	$A0
 CIODEV_LPT	.EQU	$B0
 CIODEV_ESPCON	.EQU	$C0
 CIODEV_ESPSER	.EQU	$D0
+CIODEV_SCON	.EQU	$E0
 ;
 ; SUB TYPES OF CHAR DEVICES
 ;

Source/HBIOS/pkd.asm

@@ -371,7 +371,6 @@ PKD_KEYMAP:
 	; POS	$18  $19  $1A  $1B
 	; KEY   [F4] [F3] [F2] [F1]
 	.DB	$23, $22, $21, $20
-
 ;
 ;==================================================================================================
 ; PKD OUTPUT ROUTINES

Source/HBIOS/scon.asm

@@ -0,0 +1,126 @@
+;
+;==================================================================================================
+; S100 PROPELLER CONSOLE DRIVER
+;==================================================================================================
+;
+; TODO:
+;
+SCON_IOBASE	.EQU	$00
+;
+SCON_STATUS	.EQU	SCON_IOBASE
+SCON_DATA	.EQU	SCON_IOBASE + 1
+;
+SCON_KBDRDY	.EQU	%00000010
+SCON_DSPRDY	.EQU	%00000100
+;
+SCON_COLS	.EQU	80
+SCON_ROWS	.EQU	40
+;
+;
+;
+SCON_PREINIT:
+	XOR	A
+	RET
+;
+;
+;
+SCON_INIT:
+	CALL	NEWLINE
+	PRTS("SCON:$")
+;
+	; DISPLAY CONSOLE DIMENSIONS
+	CALL	PC_SPACE
+	LD	A,SCON_COLS
+	CALL	PRTDECB
+	LD	A,'X'
+	CALL	COUT
+	LD	A,SCON_ROWS
+	CALL	PRTDECB
+	CALL	PRTSTRD
+	.TEXT	" TEXT (ANSI)$"
+;
+; ADD OURSELVES TO CIO DISPATCH TABLE
+;
+	LD	D,0			; PHYSICAL UNIT IS ZERO
+	LD	E,CIODEV_SCON		; DEVICE TYPE
+	LD	BC,SCON_FNTBL		; BC := FUNCTION TABLE ADDRESS
+	CALL	CIO_ADDENT		; ADD ENTRY, A := UNIT ASSIGNED
+	LD	(HCB + HCB_CRTDEV),A	; SET OURSELVES AS THE CRT DEVICE
+;
+	XOR	A			; SIGNAL SUCCESS
+	RET
+;
+; DRIVER FUNCTION TABLE
+;
+SCON_FNTBL:
+	.DW	SCON_IN
+	.DW	SCON_OUT
+	.DW	SCON_IST
+	.DW	SCON_OST
+	.DW	SCON_INITDEV
+	.DW	SCON_QUERY
+	.DW	SCON_DEVICE
+#IF (($ - SCON_FNTBL) != (CIO_FNCNT * 2))
+	.ECHO	"*** INVALID SCON FUNCTION TABLE ***\n"
+#ENDIF
+;
+;
+;
+SCON_IN:
+	CALL	SCON_IST		; CHECK FOR CHAR PENDING
+	JR	Z,SCON_IN		; WAIT FOR IT IF NECESSARY
+	IN0	A,(SCON_DATA)		; READ THE CHAR FROM PROPIO
+	LD	E,A
+	RET
+;
+;
+;
+SCON_IST:
+	IN0	A,(SCON_STATUS)		; READ LINE STATUS REGISTER
+	AND	SCON_KBDRDY		; ISOLATE KBDRDY
+	JP	Z,CIO_IDLE		; RETURN VIA IDLE PROCESSING
+	OR	$FF			; SET A=$FF TO SIGNAL READY
+	RET				; RETURN
+;
+;
+;
+SCON_OUT:
+	CALL	SCON_OST		; CHECK FOR OUTPUT READY
+	JR	Z,SCON_OUT		; WAIT IF NECESSARY
+	LD	A,E			; RECOVER THE CHAR TO WRITE
+	OUT0	(SCON_DATA),A		; WRITE THE CHAR TO PROPIO
+	RET
+;
+;
+;
+SCON_OST:
+	IN0	A,(SCON_STATUS)		; READ LINE STATUS REGISTER
+	AND	SCON_DSPRDY 		; ISOLATE DSPRDY
+	JP	Z,CIO_IDLE		; RETURN VIA IDLE PROCESSING
+	OR	$FF			; SET A=$FF TO SIGNAL READY
+	RET				; RETURN
+;
+;
+;
+SCON_INITDEV:
+	SYSCHKERR(ERR_NOTIMPL)
+	RET
+;
+;
+;
+SCON_QUERY:
+	LD	DE,0
+	LD	HL,0
+	XOR	A
+	RET
+;
+;
+;
+SCON_DEVICE:
+	LD	D,CIODEV_SCON		; D := DEVICE TYPE
+	LD	E,0			; E := DEVICE NUM, ALWAYS 0
+	LD	C,$BF			; C := DEVICE TYPE, 0xBF IS PROP TERM
+	LD	H,0			; H := 0, DRIVER HAS NO MODES
+	LD	L,SCON_IOBASE		; L := BASE I/O ADDRESS
+	XOR	A			; SIGNAL SUCCESS
+	RET

Source/Images/Build.cmd

@@ -13,7 +13,7 @@ call BuildDisk.cmd nzcom fd wbw_fd144 ..\zsdos\zsys_wbw.sys || exit /b
 call BuildDisk.cmd cpm3 fd wbw_fd144 ..\cpm3\cpmldr.sys || exit /b
 call BuildDisk.cmd zpm3 fd wbw_fd144 ..\zpm3\zpmldr.sys || exit /b
 call BuildDisk.cmd ws4 fd wbw_fd144 || exit /b
-call BuildDisk.cmd qpm fd wbw_fd144 d_qpm\u0\qpm.sys || exit /b
+call BuildDisk.cmd qpm fd wbw_fd144 ..\qpm\qpm_wbw.sys || exit /b
 call BuildDisk.cmd z80asm hd wbw_fd144 || exit /b
 call BuildDisk.cmd aztecc hd wbw_fd144 || exit /b
 call BuildDisk.cmd hitechc hd wbw_fd144 || exit /b
@@ -32,7 +32,7 @@ call BuildDisk.cmd cpm3 hd wbw_hd512 ..\cpm3\cpmldr.sys || exit /b
 call BuildDisk.cmd zpm3 hd wbw_hd512 ..\zpm3\zpmldr.sys || exit /b
 call BuildDisk.cmd ws4 hd wbw_hd512 || exit /b
 call BuildDisk.cmd dos65 hd wbw_hd512 ..\zsdos\zsys_wbw.sys || exit /b
-call BuildDisk.cmd qpm hd wbw_hd512 d_qpm\u0\qpm.sys || exit /b
+call BuildDisk.cmd qpm hd wbw_hd512 ..\qpm\qpm_wbw.sys || exit /b
 call BuildDisk.cmd z80asm hd wbw_hd512 || exit /b
 call BuildDisk.cmd aztecc hd wbw_hd512 || exit /b
 call BuildDisk.cmd hitechc hd wbw_hd512 || exit /b
@@ -56,7 +56,7 @@ call BuildDisk.cmd nzcom hd wbw_hd1k ..\zsdos\zsys_wbw.sys || exit /b
 call BuildDisk.cmd cpm3 hd wbw_hd1k ..\cpm3\cpmldr.sys || exit /b
 call BuildDisk.cmd zpm3 hd wbw_hd1k ..\zpm3\zpmldr.sys || exit /b
 call BuildDisk.cmd ws4 hd wbw_hd1k || exit /b
-call BuildDisk.cmd qpm hd wbw_hd1k d_qpm\u0\qpm.sys || exit /b
+call BuildDisk.cmd qpm hd wbw_hd1k ..\qpm\qpm_wbw.sys || exit /b
 call BuildDisk.cmd z80asm hd wbw_hd1k || exit /b
 call BuildDisk.cmd aztecc hd wbw_hd1k || exit /b
 call BuildDisk.cmd hitechc hd wbw_hd1k || exit /b

Source/Images/Makefile

@@ -1,7 +1,7 @@
 #
 # this makefile subsumes all the work done in Build.cmd, BuildDisk.cmd, BuildDisk.ps1
 #
-SYSTEMS = ../CPM22/cpm_wbw.sys ../ZSDOS/zsys_wbw.sys ../CPM3/cpmldr.sys ../ZPM3/zpmldr.sys
+SYSTEMS = ../CPM22/cpm_wbw.sys ../ZSDOS/zsys_wbw.sys ../QPM/qpm_wbw.sys ../CPM3/cpmldr.sys ../ZPM3/zpmldr.sys
 
 FDIMGS = fd144_cpm22.img fd144_zsdos.img fd144_nzcom.img \
 	fd144_cpm3.img fd144_zpm3.img fd144_ws4.img fd144_qpm.img \
@@ -80,7 +80,7 @@ blankhd1k:
 	@sys= ; \
 	case $@ in \
 		(*cpm22*) sys=../CPM22/cpm_wbw.sys;; \
-		(*qpm*) sys=d_qpm/u0/qpm.sys;; \
+		(*qpm*) sys=../QPM/qpm_wbw.sys;; \
 		(*zsdos* | *nzcom* | *dos65*) sys=../ZSDOS/zsys_wbw.sys;; \
 		(*cpm3*) sys=../CPM3/cpmldr.sys;; \
 		(*zpm3*) sys=../ZPM3/zpmldr.sys;; \

Source/Images/d_qpm/ReadMe.txt

@@ -36,11 +36,19 @@ code brakpoints.  This conflicts the use of that vector for any
 system that is using interrupt mode 1.  DEBUGZ can be configured
 (using DBGINST) to use a different vector.
 
-The QSTAMP program, which is used to initialize a disk for date/time
-stamping, misbehavews when run on the (new) RomWBW 1024 directory
-format disks.  It creates an invalid directory entry for the
-date/time stamp data file.  This is definitely a QP/M issue.  The
-directory entry can be manually corrected.
+The QSTAMP program, which is used to initialize a disk for date/time 
+stamping, misbehavews when run on the (new) RomWBW 1024 directory 
+format disks.  It creates an invalid directory entry for the date/time 
+stamp data file.  This is definitely a QP/M issue.  The directory entry 
+can be manually corrected.  Specifically the byte offset 15 should 
+contain the number of 128-byte records in the file.  Instead, it is set 
+to 0x01.  You can edit the entry, change it to 0x80 and everything
+starts working.
+
+There are two text files (QPMCMDS.TXT and QPMUTILS.TXT) included.  They
+came from the original QP/M 2.7 distribution.  These files have
+escape sequences imbedded in them which makes them look a little
+strange depending on the terminal emulation you are using.
 
 == QPM 2.7 Files ==
 
@@ -48,10 +56,9 @@ The following files came from the official QP/M distribution.  Actually,
 they came from 3 Microcode Consulting files (qpm27.zip, debugz.zip,
 and linkz.zip).  The original distribution files can be found on the
 Microcode Consulting website at https://www.microcodeconsulting.com/.
-Documentation (pdf) files are incuded in these original distribution
-.zip files.  These documentation files have not been included in the
-RomWBW distribution.  Please retrieve them yourself from the website
-if desired.
+Documentation (pdf) files are included in these original distribution
+.zip files.  These documentation files have been included in the
+RomWBW distribution in the Doc folder.
 
 D.COM - Directory lister
 DBGINST.COM - Configures DEBUGZ debugger

Source/Images/fd_qpm.txt

@@ -44,7 +44,7 @@ d_cpm22/u0/*.* 0:
 #
 # Add OS image
 #
-../CPM22/cpm_wbw.sys 0:cpm.sys
+../QPM/qpm_wbw.sys 0:qpm.sys
 #
 # Add Common Applications
 #

Source/Images/hd_qpm.txt

@@ -51,7 +51,7 @@ cpnet12/*.* 4:
 #
 # Add OS image
 #
-../CPM22/cpm_wbw.sys 0:cpm.sys
+../QPM/qpm_wbw.sys 0:qpm.sys
 #
 # Add Common Applications
 #

Source/Makefile

@@ -8,7 +8,7 @@ SUBDIRS += CBIOS
 SUBDIRS += Forth
 SUBDIRS += TastyBasic
 SUBDIRS += Fonts
-SUBDIRS += CPM22 ZCPR ZCPR-DJ ZSDOS CPM3 ZPM3
+SUBDIRS += CPM22 ZCPR ZCPR-DJ ZSDOS CPM3 ZPM3 QPM
 #SUBDIRS += BPBIOS
 SUBDIRS += pSys
 SUBDIRS += RomDsk

Source/QPM/Build.cmd

@@ -0,0 +1,20 @@
+@echo off
+setlocal
+
+set TOOLS=../../Tools
+
+set PATH=%TOOLS%\tasm32;%TOOLS%\zxcc;%PATH%
+
+set TASMTABS=%TOOLS%\tasm32
+
+set CPMDIR80=%TOOLS%/cpm/
+
+tasm -t80 -g3 -fFF loader.asm loader.bin loader.lst || exit /b
+
+copy /b qcp27.dat + qdos27.dat + ..\cbios\cbios_wbw.bin qpm_wbw.bin || exit /b
+copy /b qcp27.dat + qdos27.dat + ..\cbios\cbios_una.bin qpm_una.bin || exit /b
+
+copy /b loader.bin + qpm_wbw.bin qpm_wbw.sys || exit /b
+copy /b loader.bin + qpm_una.bin qpm_una.sys || exit /b
+
+goto :eof

Source/QPM/Clean.cmd

@@ -0,0 +1,8 @@
+@echo off
+setlocal
+
+if exist *.bin del *.bin
+if exist *.lst del *.lst
+if exist *.prn del *.prn
+if exist *.hex del *.hex
+if exist *.sys del *.sys

Source/QPM/Makefile

@@ -0,0 +1,15 @@
+SYSFILES = qpm_wbw.sys qpm_una.sys
+BINFILES = qpm_wbw.bin qpm_una.bin
+OBJECTS = loader.bin $(SYSFILES) $(BINFILES)
+OTHERS = *.hex
+TOOLS = ../../Tools
+include $(TOOLS)/Makefile.inc
+
+%.sys: %.bin loader.bin
+	cat loader.bin $*.bin > $@
+
+qpm_una.bin: qcp27.dat qdos27.dat ../CBIOS/cbios_una.bin
+	cat qcp27.dat qdos27.dat ../CBIOS/cbios_una.bin > $@
+
+qpm_wbw.bin: qcp27.dat qdos27.dat ../CBIOS/cbios_wbw.bin
+	cat qcp27.dat qdos27.dat ../CBIOS/cbios_wbw.bin > $@

Source/QPM/ReadMe.txt

@@ -0,0 +1,15 @@
+QPM27
+-----
+
+QPM is not available in source form.  In this folder, you will find
+qcp27.dat and qdos27.dat.  These are the CCP and BDOS components for
+QPM.  They were created by running QINSTALL on a normal RomWBW
+CP/M 2.2 system, then extracting the resultant CCP and BDOS binaries.
+
+When this folder goes through the build process, it just combines the
+QPM CCP and BDOS binaries with the RomWBW CBIOS to create an up-to-date
+QPM system image.
+
+QPM 2.7 is distributed at https://www.microcodeconsulting.com/.
+
+-- WBW 3:13 PM 9/9/2023

Source/QPM/loader.asm

@@ -0,0 +1,271 @@
+;===============================================================================
+; LOADER.ASM
+;
+; BOOTLOADER FOR ROMWBW DISK OPERATING SYSTEMS.
+;
+; CP/M DISK FORMATS ALLOW FOR RESERVED TRACKS THAT CONTAIN AN IMAGE OF THE
+; OPERATING SYSTEM TO BE LOADED WHEN THE DISK IS BOOTED.  THE OPERATING SYSTEM
+; IMAGE ITSELF IS NORMALLY PREFIXED BY A 1-N SECTORS CONTAINING OS BOOTSTRAP
+; CODE AND DISK METADATA.
+;
+; THE RETROBREW COMPUTING GROUP HAS BEEN USING A CONVENTION OF PREFIXING THE
+; OS IMAGE WITH 3 SECTORS (512 BYTES X 3 FOR A TOTAL OF 1536 BYTES):
+;
+;   SECTOR 1: IBM-PC STYLE BOOT BLOCK CONTAINING BOOTSTRAP, 
+;             PARTITION TABLE, AND BOOT SIGNATURE
+;   SECTOR 2: RESERVED
+;   SECTOR 3: METADATA
+;
+; THE HARDWARE BIOS IS EXPECTED TO READ AND LOAD THE FIRST TWO SECTORS FROM THE
+; DISK TO MEMORY ADDRESS $8000 AND JUMP TO THAT LOCATION TO BEGIN THE BOOT
+; PROCESS.  THE BIOS IS EXPECTED TO VERIFY THAT A STANDARD BOOT SIGNATURE
+; OF $55, $AA IS PRESENT AT OFFSET $1FE-$1FF.  IF THE SIGNATURE IS NOT FOUND,
+; THE BIOS SHOULD ASSUME THE DISK HAS NOT BEEN PROPERLY INITIALIZED AND SHOULD
+; NOT JUMP TO THE LOAD ADDRESS.
+;
+;===============================================================================
+;
+#INCLUDE "../ver.inc"
+;
+SYS_ENT		.EQU	$E600		; SYSTEM (OS) ENTRY POINT ADDRESS
+SYS_LOC		.EQU	$D000		; STARTING ADDRESS TO LOAD SYSTEM IMAGE
+SYS_END		.EQU	$FE00		; ENDING ADDRESS OF SYSTEM IMAGE
+;
+SEC_SIZE	.EQU	512		; DISK SECTOR SIZE
+BLK_SIZE	.EQU	128		; OS BLOCK/RECORD SIZE
+;
+PREFIX_SIZE	.EQU	(SEC_SIZE * 3)	; 3 SECTORS
+;
+META_SIZE	.EQU	32		; SEE BELOW
+META_LOC	.EQU	(PREFIX_SIZE - META_SIZE)
+;
+PT_LOC		.EQU	$1BE
+PT_SIZ		.EQU	$40
+;
+;-------------------------------------------------------------------------------
+; SECTOR 1
+;
+;   THIS SECTOR FOLLOWS THE CONVENTIONS OF AN IBM-PC MBR CONTAINING THE OS
+;   BOOTSTRAP CODE, PARTITION TABLE, AND BOOT SIGNATURE
+;
+;----------------------------------------------------------------------------
+;
+; THE FOLLOWING BOOTSTRAP CODE IS BUILT TO ASSUME IT WILL BE EXECUTED AT A STARTING
+; ADDRESS OF $8000.  THIS CODE IS *ONLY* FOR UNA.  THE ROMWBW ROM BOOTLOADER
+; USES THE METADATA TO LOAD THE OS DIRECTLY.
+;
+	.ORG	$8000
+	JR	BOOT
+;
+BOOT:
+	LD	DE,STR_LOAD	; LOADING STRING
+	CALL	PRTSTR		; PRINT
+	CALL	PRTDOT		; PROGRESS
+;
+	LD	BC,$00FC	; UNA FUNC: GET BOOTSTRAP HISTORY
+	CALL	$FFFD		; CALL UNA
+	JR	NZ,ERROR	; HANDLE ERROR
+	CALL	PRTDOT		; PROGRESS
+	LD	B,L		; MOVE BOOT UNIT ID TO B
+;
+	LD	C,$41		; UNA FUNC: SET LBA
+	LD	DE,0		; HI WORD ALWAYS ZERO
+	LD	HL,3		; IMAGE STARTS AT FOURTH SECTOR
+	CALL	$FFFD		; SET LBA
+	JR	NZ,ERROR	; HANDLE ERROR
+	CALL	PRTDOT		; PROGRESS
+;
+	LD	C,$42		; UNA FUNC: READ SECTORS
+	LD	DE,$D000	; STARTING ADDRESS FOR IMAGE
+	LD	L,22		; READ 22 SECTORS
+	CALL	$FFFD		; DO READ
+	JR	NZ,ERROR	; HANDLE ERROR
+	CALL	PRTDOT		; PROGRESS
+;
+	LD	DE,STR_DONE	; DONE MESSAGE
+	CALL	PRTSTR		; PRINT IT
+;
+	LD	D,B		; PASS BOOT UNIT TO OS
+	LD	E,0		; ASSUME LU IS ZERO
+	JP	SYS_ENT		; GO TO SYSTEM
+;
+PRTCHR:
+	PUSH	BC
+	PUSH	DE
+	LD	BC,$0012	; UNIT 0, WRITE CHAR
+	LD	E,A		; CHAR TO PRINT
+	CALL	$FFFD		; PRINT
+	POP	DE
+	POP	BC
+	RET
+;
+PRTSTR:
+	PUSH	BC
+	PUSH	HL
+	LD	BC,$0015	; UNIT 0, WRITE CHARS UNTIL TERMINATOR
+	LD	L,0		; TERMINATOR IS NULL
+	CALL	$FFFD		; PRINT
+	POP	HL
+	POP	BC
+	RET
+;
+PRTDOT:
+	LD	A,'.'		; DOT CHARACTER
+	JR	PRTCHR		; PRINT AND RETURN
+;
+; PRINT THE HEX BYTE VALUE IN A
+;
+PRTHEXBYTE:
+	PUSH	AF
+	PUSH	DE
+	CALL	HEXASCII
+	LD	A,D
+	CALL	PRTCHR
+	LD	A,E
+	CALL	PRTCHR
+	POP	DE
+	POP	AF
+	RET
+;
+; CONVERT BINARY VALUE IN A TO ASCII HEX CHARACTERS IN DE
+;
+HEXASCII:
+	LD	D,A
+	CALL	HEXCONV
+	LD	E,A
+	LD	A,D
+	RLCA
+	RLCA
+	RLCA
+	RLCA
+	CALL	HEXCONV
+	LD	D,A
+	RET
+;
+; CONVERT LOW NIBBLE OF A TO ASCII HEX
+;
+HEXCONV:
+	AND	$0F	     ;LOW NIBBLE ONLY
+	ADD	A,$90
+	DAA	
+	ADC	A,$40
+	DAA	
+	RET	
+;
+ERROR:
+	LD	DE,STR_ERR		; POINT TO ERROR STRING
+	CALL	PRTSTR			; PRINT IT
+	HALT				; HALT
+;
+; DATA
+;
+STR_LOAD	.DB	"\r\nLoading",0
+STR_DONE	.DB	"\r\n",0
+STR_ERR		.DB	" Read Error!",0
+;
+	.ORG	$ - $8000		; BACK TO ABSOLUTE ADDRESS
+;
+	.FILL	PT_LOC - $,0		; FILL TO START OF PARTITION TABLE
+;
+; STANDARD IBM-PC PARTITION TABLE.  ALTHOUGH A
+; PARTITION TABLE IS NOT RELEVANT FOR A FLOPPY DISK, IT DOES NO HARM.
+; THE CONTENTS OF THE PARTITION TABLE CAN BE MANAGED BY FDISK80.
+;
+; BELOW WE ALLOW FOR 32 SLICES OF ROMWBW CP/M FILESYSTEMS
+; FOLLOWED BY A FAT16 PARTITION.  THE SLICES FOLLOW THE ORIGINAL
+; HD512 ROMWBW FORMAT.  IF THE DISK IS USING HD1K, A SEPARATE
+; PARTITION TABLE WILL BE IN PLACE AND RENDER THIS PARTITION TABLE
+; IRRELEVANT.
+;
+; THE CYL/SEC FIELDS ENCODE CYLINDER AND SECTOR AS:
+;	CCCCCCCC:CCSSSSSS
+;	76543210:98543210
+;
+PART0:
+	.DB	0			; ACTIVE IF $80
+	.DB	0			; CHS START ADDRESS (HEAD)
+	.DW	0			; CHS START ADDRESS (CYL/SEC)
+	.DB	0			; PART TYPE ID
+	.DB	0			; CHS LAST ADDRESS (HEAD)
+	.DW	0			; CHS LAST ADDRESS (CYL/SEC)
+	.DW	0,0			; LBA FIRST (DWORD)
+	.DW	0,0			; LBA COUNT (DWORD)
+PART1:
+	.DB	0			; ACTIVE IF $80
+	.DB	0			; CHS START ADDRESS (HEAD)
+	.DW	%1111111111000001	; CHS START ADDRESS (CYL/SEC)
+	.DB	6			; PART TYPE ID
+	.DB	15			; CHS LAST ADDRESS (HEAD)
+	.DW	%1111111111010000	; CHS LAST ADDRESS (CYL/SEC)
+	.DW	$4000,$0010		; LBA FIRST (DWORD)
+	.DW	$0000,$000C		; LBA COUNT (DWORD)
+PART2:
+	.DB	0			; ACTIVE IF $80
+	.DB	0			; CHS START ADDRESS (HEAD)
+	.DW	0			; CHS START ADDRESS (CYL/SEC)
+	.DB	0			; PART TYPE ID
+	.DB	0			; CHS LAST ADDRESS (HEAD)
+	.DW	0			; CHS LAST ADDRESS (CYL/SEC)
+	.DW	0,0			; LBA FIRST (DWORD)
+	.DW	0,0			; LBA COUNT (DWORD)
+PART3:
+	.DB	0			; ACTIVE IF $80
+	.DB	0			; CHS START ADDRESS (HEAD)
+	.DW	0			; CHS START ADDRESS (CYL/SEC)
+	.DB	0			; PART TYPE ID
+	.DB	0			; CHS LAST ADDRESS (HEAD)
+	.DW	0			; CHS LAST ADDRESS (CYL/SEC)
+	.DW	0,0			; LBA FIRST (DWORD)
+	.DW	0,0			; LBA COUNT (DWORD)
+;
+; THE END OF THE FIRST SECTOR MUST CONTAIN THE TWO BYTE BOOT SIGNATURE.
+;
+BOOTSIG	.DB	$55,$AA			; STANDARD BOOT SIGNATURE
+;
+;-------------------------------------------------------------------------------
+; SECTOR 2
+;
+;   THIS SECTOR HAS NOT BEEN DEFINED AND IS RESERVED.
+;
+;----------------------------------------------------------------------------
+;
+	.FILL	SEC_SIZE,0			; JUST FILL SECTOR WITH ZEROES
+;
+;-------------------------------------------------------------------------------
+; SECTOR 3
+;
+;   OS AND DISK METADATA
+;
+;----------------------------------------------------------------------------
+;
+	.FILL	(BLK_SIZE * 3),0	; FIRST 384 BYTES ARE NOT YET DEFINED
+;
+; THE FOLLOWING TWO BYTES ARE AN ADDITIONAL SIGNATURE THAT IS VERIFIED BY
+; SOME HARDWARE BIOSES.
+;
+PR_SIG		.DB	$5A,$A5		; SIGNATURE GOES HERE
+;
+		.FILL	(META_LOC - $),0
+;
+; METADATA
+;
+PR_WP		.DB	0		; (1) WRITE PROTECT BOOLEAN
+PR_UPDSEQ	.DW	0		; (2) PREFIX UPDATE SEQUENCE NUMBER (DEPRECATED?)
+PR_VER		.DB	RMJ,RMN,RUP,RTP	; (4) OS BUILD VERSION
+PR_LABEL	.DB	"Unlabeled$$$$$$$","$"	; (17) DISK LABEL (EXACTLY 16 BYTES!!!)
+		.DW	0		; (2) DEPRECATED
+PR_LDLOC	.DW	SYS_LOC		; (2) ADDRESS TO START LOADING SYSTEM
+PR_LDEND	.DW	SYS_END		; (2) ADDRESS TO STOP LOADING SYSTEM
+PR_ENTRY	.DW	SYS_ENT		; (2) ADDRESS TO ENTER SYSTEM (OS)
+;
+#IF (META_SIZE != ($ - META_LOC))
+	.ECHO "META_SIZE VALUE IS WRONG!!!\r\n"
+	!!!
+#ENDIF
+;
+#IF ($ != PREFIX_SIZE)
+	.ECHO "LOADER PREFIX IS WRONG SIZE!!!\r\n"
+	!!!
+#ENDIF
+;
+	.END

Source/ver.inc

@@ -2,7 +2,7 @@
 #DEFINE	RMN	3
 #DEFINE	RUP	0
 #DEFINE	RTP	0
-#DEFINE BIOSVER	"3.3.0-dev.45"
+#DEFINE BIOSVER	"3.3.0-dev.52"
 #define rmj	RMJ
 #define rmn	RMN
 #define rup	RUP

Source/ver.lib

@@ -3,5 +3,5 @@ rmn	equ	3
 rup	equ	0
 rtp	equ	0
 biosver	macro
-	db	"3.3.0-dev.45"
+	db	"3.3.0-dev.52"
 	endm