SD Media Automatic Drive Assignment - Issue #365

- Modified SD Media handling such that no OS drive letters will be assigned automatically at OS Startup if there is no media inserted.
Issue #366
2026-02-07 06:53:13 -06:00 · 2023-10-05 10:14:30 -07:00 · 2023-10-04 16:54:34 -07:00 · 2023-10-03 19:44:49 -07:00 · 2023-10-03 15:24:18 -07:00 · 2023-10-01 17:22:19 -07:00
217 changed files with 6113 additions and 563 deletions
--- a/Doc/ChangeLog.txt
+++ b/Doc/ChangeLog.txt
@@ -19,6 +19,10 @@ Version 3.3
 - WBW: Early support for Duodyne base system (CPU/UART/ROM/RAM/RTC/SPK)
 - M?C: Fixed XM to allow specifying HBIOS port for send operations
 - WBW: Fix S100 Z180 LED operation (credit to Jay Cotton for finding this issue)
+- WBW: QPM system image is now combined with current CBIOS during build
+- WBW: Added framework for Heath platform
+- WBW: Support for USB Disks via CH375/CH376
+- D?J: Support for Raspberry Pi build process

 Version 3.2.1
 -------------
--- a/Applications.pdf
+++ b/Applications.pdf
--- a/Catalog.pdf
+++ b/Catalog.pdf
--- a/Errata.pdf
+++ b/Errata.pdf
--- a/Applications.pdf
+++ b/Applications.pdf
--- a/Doc/RomWBW
+++ b/Doc/RomWBW
--- a/Doc/RomWBW
+++ b/Doc/RomWBW
--- a/ReadMe.md
+++ b/ReadMe.md
@@ -3,7 +3,7 @@
 **RomWBW ReadMe** \
 Version 3.3 \
 Wayne Warthen  ([wwarthen@gmail.com](mailto:wwarthen@gmail.com)) \
-08 Aug 2023
+04 Oct 2023

 # Overview

--- a/ReadMe.txt
+++ b/ReadMe.txt
@@ -1,6 +1,6 @@
 RomWBW ReadMe
 Wayne Warthen (wwarthen@gmail.com)
-08 Aug 2023
+04 Oct 2023



--- a/Source/Apps/FDU/fdu.doc
+++ b/Source/Apps/FDU/fdu.doc
@@ -153,7 +153,8 @@ JP2 (/FAULT) shorted, JP3 (MINI): 2-3, JP4 (/DC/RDY): 2-3.

 The RCBus Scott Baker WDC-based floppy module should be jumpered
 for I/O base address 0x50 (SV1: 11-12), JP1 (/DACK): 1-2,
-JP2 (TC): 2-3.
+JP2 (TC): 2-3.  Note that pin 1 of JPX jumpers is toward the bottom
+of the board.

 The RCBus FDC by Alan Cox (Etched Pixels) needs to be strapped
 for base I/O address 0x48.
--- a/Source/Apps/Test/DMAmon/dmamon.asm
+++ b/Source/Apps/Test/DMAmon/dmamon.asm
@@ -27,9 +27,9 @@ DMAIOTST	.EQU	$68		; AN OUTPUT PORT FOR TESTING - 16C450 SERIAL OUT
 ;
 #IF (DMAMODE==DMAMODE_DUO)
 DMABASE		.SET	$40		; DMA: DMA0 BASE ADDRESS
-;DMABASE 	.SET	$41		; DMA: DMA1 BASE ADDRESS
 DMALATCH	.SET	$43		; DMA: DMA LATCH ADDRESS
 DMAIOTST	.SET	$58		; AN OUTPUT PORT FOR TESTING - 16C450 SERIAL OUT
+;DMAIOTST	.SET	$94		; AN ALT OUTPUT PORT FOR TESTING - RTC/SPEAKER/LEDS PORT
 #ENDIF
 ;
 ;==================================================================================================
@@ -127,7 +127,7 @@ MAIN:
 	LD	SP,STACK		; STACK
 ;
 	call	PRTSTRD			; WELCOME
-	.db	"\n\rDMA Monitor V3\n\r$"
+	.db	"\n\rDMA Monitor V3.1\n\r$"
 ;
 #IF (INTENABLE)
 ;
@@ -136,6 +136,8 @@ MAIN:
 	ld	de,$A000
 	ld	bc,hsiz
 	ldir
+	ld	a,(dmaport)
+	ld	(int_dmaport),a
 ;
 	; Install interrupt vector (RomWBW specific!!!)
 	ld	hl,int		; pointer to my interrupt handler
@@ -215,6 +217,9 @@ DMACFG_S:
 	call	HEXIN
 	ld	hl,dmaport
 	ld	(hl),a
+#IF (INTENABLE)
+	ld	(int_dmaport),a
+#ENDIF
 	jp	MENULP
 ;
 DMACFG_L:
@@ -398,7 +403,8 @@ DMA_INIT:
 ;
 	ld	hl,DMACode		; program the
 	ld	b,DMACode_Len		; dma command
-	ld	c,DMABASE		; block
+	ld	a,(dmaport)
+	ld	c,a		; block
 ;
 	di
 	otir				; load dma
@@ -509,6 +515,7 @@ DMACFG_V:
 ;==================================================================================================
 ;
 DMABUF	.TEXT	"0123456789abcdef"
+;DMABUF	.DB	$04,$00,$04,$00,$04,$00,$04,$00,$04,$00,$04,$00,$04,$00,$04,$00,$00,$00,$00 ; SPEAKER
 ;
 DMA_ReadyO:
 	call	PRTSTRD
@@ -631,9 +638,9 @@ DMAMemMove1:
 ;
 DMAMemMove2:
 ;
-;	LD	HL,$8400	; PLANT
-;	LD	A,$00		; BAD
-;	LD	(HL),A		; SEED
+	;LD	HL,$8400	; PLANT
+	;LD	A,$00		; BAD
+	;LD	(HL),A		; SEED
 ;
 	LD	A,$AA		; CHECK COPY SUCCESSFULL
 	LD	HL,$8000
@@ -641,6 +648,14 @@ DMAMemMove2:
 NXTCMP:	CPI
 	JP	PO,CMPOK
 	JR	Z,NXTCMP
+
+	DEC	HL
+	CALL	PRTHEXWORDHL
+	LD	A,' '
+	CALL	COUT
+	LD	A,(HL)
+	CALL	PRTHEXBYTE
+	
 	RET			; RET W/ ZF CLEAR
 ;
 CMPOK:
@@ -1193,7 +1208,6 @@ CST:
 	RET
 ;
 USEINT	.DB	FALSE		; USE INTERRUPTS FLAG
-counter	.dw	0	
 dmaport	.db	DMABASE
 dmalach	.db	DMALATCH
 dmaxfer	.db	DMA_XMODE
@@ -1214,11 +1228,16 @@ reladr	.equ	$		; relocation start adr
 	.org	$A000		; code will run here
 ;
 int:
+	;LD	E,'.'			; OUTPUT CHAR TO E
+	;LD	C,CIO_CONSOLE		; CONSOLE UNIT TO C
+	;LD	B,BF_CIOOUT		; HBIOS FUNC: OUTPUT CHAR
+	;CALL	$FFF0			; HBIOS OUTPUTS CHARACTER
+
 	; According to the DMA doc, you must issue
 	; a DMA_DISABLE command prior to a
 	; DMA_REINIT_STATUS_BYTE command to avoid a
 	; potential race condition.
-	ld	a,(dmaport)
+	ld	a,(int_dmaport)
 	ld	c,a
 	ld	a,DMA_DISABLE
 	out	(c),a
@@ -1238,6 +1257,11 @@ int:
 	or	$ff		; signal int handled
 	ret
 ;
+; data referred to in handler must reside in high mem
+;
+int_dmaport	.db	0	; hi mem copy of dmaport
+counter		.dw	0	; interrupt counter
+;
 hsiz	.equ	$ - $A000	; size of handler to relocate
 ;
 	.org	reladr + hsiz
--- a/Source/Apps/Test/I2C/Build.cmd
+++ b/Source/Apps/Test/I2C/Build.cmd
@@ -8,6 +8,8 @@ set TASMTABS=%TOOLS%\tasm32
 tasm -t180 -g3 -fFF i2cscan.asm i2cscan.com i2cscan.lst || exit /b
 tasm -t180 -g3 -fFF rtcds7.asm rtcds7.com rtcds7.lst || exit /b
 tasm -t180 -g3 -fFF i2clcd.asm i2clcd.com i2clcd.lst || exit /b
+tasm -t80 -g3 -ff srom.asm srom.com srom.lst || exit /b

 copy /Y i2c*.com ..\..\..\..\Binary\Apps\Test\ || exit /b
 copy /Y rtcds7*.com ..\..\..\..\Binary\Apps\Test\ || exit /b
+copy /Y srom.com ..\..\..\..\Binary\Apps\Test\ || exit /b
--- a/Source/Apps/Test/I2C/Makefile
+++ b/Source/Apps/Test/I2C/Makefile
@@ -1,4 +1,4 @@
-OBJECTS = i2cscan.com rtcds7.com i2clcd.com
+OBJECTS = i2cscan.com rtcds7.com i2clcd.com srom.com
 DEST = ../../../../Binary/Apps/Test/
 TOOLS = ../../../../Tools

--- a/Source/Apps/Test/I2C/srom.asm
+++ b/Source/Apps/Test/I2C/srom.asm
--- a/Source/Apps/assign.asm
+++ b/Source/Apps/assign.asm
@@ -31,6 +31,7 @@
 ;   2022-02-28 [WBW] Use HBIOS to swap banks under CP/M 3
 ;                    Use CPM3 BDOS direct BIOS call to get DRVTBL adr
 ;   2023-06-19 [WBW] Update for revised DIODEVICE API
+;   2023-09-19 [WBW] Added CHUSB & CHSD device support
 ;_______________________________________________________________________________
 ;
 ; ToDo:
@@ -1920,8 +1921,8 @@ dev09	.db	"HDSK",0
 dev10	.db	"PPA",0
 dev11	.db	"IMM",0
 dev12	.db	"SYQ",0
-dev13	.equ	devunk
-dev14	.equ	devunk
+dev13	.db	"CHUSB",0
+dev14	.db	"CHSD",0
 dev15	.equ	devunk
 ;
 devcnt	.equ	10		; 10 devices defined
@@ -1942,10 +1943,10 @@ stack	.equ	$		; stack top
 ; Messages
 ;
 indent	.db	"   ",0
-msgban1	.db	"ASSIGN v1.6 for RomWBW CP/M ",0
+msgban1	.db	"ASSIGN v1.7 for RomWBW CP/M ",0
 msg22	.db	"2.2",0
 msg3	.db	"3",0
-msbban2	.db	", 16-Jun-2023",0
+msbban2	.db	", 19-Sep-2023",0
 msghb	.db	" (HBIOS Mode)",0
 msgub	.db	" (UBIOS Mode)",0
 msgban3	.db	"Copyright 2021, Wayne Warthen, GNU GPL v3",0
--- a/Source/BPBIOS/diskdefs
+++ b/Source/BPBIOS/diskdefs
@@ -310,6 +310,32 @@ diskdef wbw_rom1024
  os 2.2
 end

+# RomWBW 512KB RAM (256KB reserved, 256KB RAM Disk)
+
+diskdef wbw_ram512
+  seclen 512
+  tracks 8
+  sectrk 64
+  blocksize 2048
+  maxdir 256
+  skew 0
+  boottrk 0
+  os 2.2
+end
+
+# RomWBW 1024KB RAM (256KB reserved, 768KB RAM Disk)
+
+diskdef wbw_ram1024
+  seclen 512
+  tracks 24
+  sectrk 64
+  blocksize 2048
+  maxdir 256
+  skew 0
+  boottrk 0
+  os 2.2
+end
+
 # RomWBW 720K floppy media

 diskdef wbw_fd720
--- a/Source/BuildShared.cmd
+++ b/Source/BuildShared.cmd
@@ -4,6 +4,7 @@ setlocal
 pushd HDIAG && call Build || exit /b & popd
 pushd CBIOS && call Build || exit /b & popd
 pushd CPM22 && call Build || exit /b & popd
+pushd QPM && call Build || exit /b & popd
 pushd ZCPR && call Build || exit /b & popd
 pushd ZCPR-DJ && call Build || exit /b & popd
 pushd ZSDOS && call Build || exit /b & popd
--- a/Source/CBIOS/cbios.asm
+++ b/Source/CBIOS/cbios.asm
@@ -2529,24 +2529,21 @@ MD_INIT:
 ; UDPATE THE RAM/ROM DPB STRUCTURES BASED ON HARDWARE
 ;
 #IFDEF PLTWBW
-	; TODO: HANDLE DISABLED RAM/ROM DISK BETTER.
-	; IF RAM OR ROM DISK ARE DISABLED, BELOW WILL STILL
-	; TRY TO ADJUST THE DPB BASED ON RAM BANK CALCULATIONS.
-	; IT SHOULD NOT MATTER BECAUSE THE DPB SHOULD NEVER BE
-	; USED.  IT WOULD BE BETTER TO GET RAMD0/ROMD0 AND
-	; RAMDN/ROMDN FROM THE HCB AND USE THOSE TO CALC THE
-	; DPB ADJUSTMENT.  IF DN-D0=0, BYPASS ADJUSTMENT.
-	LD	A,(HCB + HCB_ROMBANKS)	; ROM BANK COUNT
-	SUB	4		; REDUCE BANK COUNT BY RESERVED PAGES
-	LD	IX,DPB_ROM	; ADDRESS OF DPB
-	CALL	MD_INIT1	; FIX IT UP
+	; NOTE: ROM AND/OR RAM DISK MAY NOT BE ACTIVE, BUT WE GO
+	; AHEAD AND UPDATE BOTH DPBS ANYWAY.  IT CAUSES NO HARM SINCE
+	; INACTIVE RAM/ROM DISK WILL NEVER BE ACCESSED.
 ;
-	LD	A,(HCB + HCB_RAMBANKS)	; RAM BANK COUNT
-	SUB	8		; REDUCE BANK COUNT BY RESERVED PAGES
-	LD	IX,DPB_RAM	; ADDRESS OF DPB
-	CALL	MD_INIT1	; FIX IT UP
+	; ROM DISK
+	LD	A,(HCB + HCB_ROMD_BNKS)	; ROM DISK SIZE IN BANKS
+	LD	IX,DPB_ROM		; ADDRESS OF DPB
+	CALL	MD_INIT1		; FIX IT UP
 ;
-	JR	MD_INIT4	; DONE
+	; RAM DISK
+	LD	A,(HCB + HCB_RAMD_BNKS)	; RAM DISK SIZE IN BANKS
+	LD	IX,DPB_RAM		; ADDRESS OF DPB
+	CALL	MD_INIT1		; FIX IT UP
+;	
+	JR	MD_INIT4		; DONE
 ;
 MD_INIT1:
 ;
@@ -3394,8 +3391,8 @@ DEV09	.DB	"HDSK$"
 DEV10	.DB	"PPA$"
 DEV11	.DB	"IMM$"
 DEV12	.DB	"SYQ$"
-DEV13	.EQU	DEVUNK
-DEV14	.EQU	DEVUNK
+DEV13	.DB	"CHUSB$"
+DEV14	.DB	"CHSD$"
 DEV15	.EQU	DEVUNK
 ;
 #ENDIF
--- a/Source/CPM3/diskio.z80
+++ b/Source/CPM3/diskio.z80
@@ -355,38 +355,30 @@ dpb$hdnew:	; 8MB Hard Disk Drive (new format)
 ;		called for first time initialization.

 dsk$init:
-	; TODO: Handle disabled RAM/ROM disk better.
-	; If RAM or ROM disk are disabled, below will still
-	; try to adjust the DPB based on RAM bank calculations.
-	; It should not matter because the DPB should never be
-	; used.  It would be better to get RAMD0/ROMD0 and
-	; RAMDN/ROMDN from the HCB and use those to calc the
-	; DPB adjustment.  If DN-D0=0, bypass adjustment.
-	ld	b,0FAh			; HBIOS Peek Function
-	ld	a,(@hbbio)		; HBIOS bank id
-	ld	d,a			; ... goes in D
-	ld	hl,10Ch			; Offset 10Ch is ROM bank cnt
-	rst	08			; Call HBIOS, value in E
-	ld	a,e			; move count to accum
-	sub	4			; reduce by # reserved banks
-	ld	ix,dpb$rom		; address of DPB
-	call	dsk$init1		; fix it up
-	
-	ld	b,0FAh			; HBIOS Peek Function
-	ld	a,(@hbbio)		; HBIOS bank id
-	ld	d,a			; ... goes in D
-	ld	hl,10Bh			; Offset 10Bh is RAM bank cnt
-	rst	08			; Call HBIOS, value in E
-	ld	a,e			; move count to accum
-	sub	8			; reduce by # reserved banks
-	ld	ix,dpb$ram		; address of DPB
-	call	dsk$init1		; fix it up

+	; NOTE: ROM and/or RAM disk may not be active, but we go
+	; ahead and update both DPBs anyway.  It causes no harm since
+	; inactive RAM/ROM disk will never be accessed.
+
+	ld	hl,1DFh			; ROM disk bank cnt in HCB
+	ld	ix,dpb$rom		; address of ROM Disk DPB
+	call	dsk$init1		; fix it up
+	ld	hl,1DDh			; RAM dsik bank cnt in HCB
+	ld	ix,dpb$ram		; address of RAM Disk DPB
+	call	dsk$init1		; fix it up
 	ret				; done

 dsk$init1:
+	; Get bank count of RAM/ROM disk
+	ld	b,0FAh			; HBIOS Peek Function
+	ld	a,(@hbbio)		; HBIOS bank id
+	ld	d,a			; ... goes in D
+	rst	08			; Call HBIOS, value in E
+	;ld	a,e			; move count to accum
+
 	; Setup HL with bank count
-	ld	l,a			; lsb
+	;ld	l,a			; lsb
+	ld	l,e			; lsb
 	ld	h,0			; msb is always zero

 	; Update EXM field
--- a/Source/CPM3/genbnk.dat
+++ b/Source/CPM3/genbnk.dat
@@ -8,12 +8,12 @@ MEMTOP   = FD
 BNKSWT   = Y
 COMBAS   = 80
 LERROR   = Y
-NUMSEGS  = 04
+NUMSEGS  = 02
 MEMSEG00 = 01,17,00
 MEMSEG01 = 0E,72,02
 MEMSEG02 = 01,7F,03
-MEMSEG03 = 01,7F,04
-MEMSEG04 = 01,7F,05
+MEMSEG03 = 00,C0,04
+MEMSEG04 = 00,C0,05
 MEMSEG05 = 00,C0,06
 MEMSEG06 = 00,C0,07
 MEMSEG07 = 00,C0,08
@@ -25,38 +25,38 @@ MEMSEG0C = 00,C0,0D
 MEMSEG0D = 00,C0,0E
 MEMSEG0E = 00,C0,0F
 MEMSEG0F = 00,C0,10
-HASHDRVA = Y
-HASHDRVB = Y
-HASHDRVC = Y
-HASHDRVD = Y
-HASHDRVE = Y
-HASHDRVF = Y
-HASHDRVG = Y
-HASHDRVH = Y
-HASHDRVI = Y
-HASHDRVJ = Y
-HASHDRVK = Y
-HASHDRVL = Y
-HASHDRVM = Y
-HASHDRVN = Y
-HASHDRVO = Y
-HASHDRVP = Y
-ALTBNKSA = Y
-ALTBNKSB = Y
-ALTBNKSC = Y
-ALTBNKSD = Y
-ALTBNKSE = Y
-ALTBNKSF = Y
-ALTBNKSG = Y
-ALTBNKSH = Y
-ALTBNKSI = Y
-ALTBNKSJ = Y
-ALTBNKSK = Y
-ALTBNKSL = Y
-ALTBNKSM = Y
-ALTBNKSN = Y
-ALTBNKSO = Y
-ALTBNKSP = Y
+HASHDRVA = N
+HASHDRVB = N
+HASHDRVC = N
+HASHDRVD = N
+HASHDRVE = N
+HASHDRVF = N
+HASHDRVG = N
+HASHDRVH = N
+HASHDRVI = N
+HASHDRVJ = N
+HASHDRVK = N
+HASHDRVL = N
+HASHDRVM = N
+HASHDRVN = N
+HASHDRVO = N
+HASHDRVP = N
+ALTBNKSA = N
+ALTBNKSB = N
+ALTBNKSC = N
+ALTBNKSD = N
+ALTBNKSE = N
+ALTBNKSF = N
+ALTBNKSG = N
+ALTBNKSH = N
+ALTBNKSI = N
+ALTBNKSJ = N
+ALTBNKSK = N
+ALTBNKSL = N
+ALTBNKSM = N
+ALTBNKSN = N
+ALTBNKSO = N
+ALTBNKSP = N
 NDIRRECA = 08
 NDIRRECB = 00
 NDIRRECC = 00
--- a/Source/CPM3/genres.dat
+++ b/Source/CPM3/genres.dat
@@ -8,7 +8,7 @@ MEMTOP   = FD
 BNKSWT   = N
 COMBAS   = 00
 LERROR   = Y
-NUMSEGS  = 03
+NUMSEGS  = 01
 MEMSEG00 = 00,80,00
 MEMSEG01 = 00,C0,02
 MEMSEG02 = 00,C0,03
--- a/Source/CPM3/move.z80
+++ b/Source/CPM3/move.z80
@@ -65,12 +65,11 @@ xbnkmov:
 ; ------------	--------------	-------
 ; COMMON	BID_COM		8Fh
 ; 0: OS/BUFS	BID_USR         8Eh
-;		BID_BIOS	8Dh	
-; 1: TPA	BID_AUX		8Ch
-; 2: BUFS	BID_AUX-1	8Bh
-; 3: BUFS	BID_AUX-2	8Ah
-; 4: BUFS	BID_AUX-3	89h
-; 5: BUFS	BID_AUX-4	88h
+; 1: TPA	BID_AUX		8Dh
+; 2: BUFS	BID_AUX-1	8Ch
+; 3: BUFS	BID_AUX-2	8Bh
+; 4: BUFS	BID_AUX-3	8Ah
+; 5: BUFS	BID_AUX-4	89h
 ;
 ; N.B., Below BID_AUX is considered RAM disk bank.  Need to
 ; make sure RAM disk is kept small enough to stay below
@@ -80,17 +79,13 @@ xbnkmov:
 ; to adjust for real size of RAM in system
 ;
 ?bnkxlt:
-	or	a
-	jr	z,bank0
-	neg			; 2 -> -2
-	add	a,8Dh		; 8Dh - 2 = 8Bh
-@hbbio	equ	$ - 1		; BID_BIOS
-	ret
-bank0:
-	ld	a,8Eh		; 0 -> 8Eh
+	neg			; ex: 2 -> -2
+	add	a,8Eh		; ex: 8Eh - 2 = 8Ch
@hbusr	equ	$ - 1		; BID_USR
 	ret
-	
+
+@hbbio	db	0		; BID_BIOS
+
 movtyp	db	0		; non-zero for interbank move

 movbnks:
--- a/Source/Clean.cmd
+++ b/Source/Clean.cmd
@@ -4,6 +4,7 @@ setlocal
 pushd HDIAG && call Clean.cmd & popd
 pushd Apps && call Clean.cmd & popd
 pushd CPM22 && call Clean.cmd & popd
+pushd QPM && call Clean.cmd & popd
 pushd ZCPR && call Clean.cmd & popd
 pushd ZCPR-DJ && call Clean.cmd & popd
 pushd ZSDOS && call Clean.cmd & popd
--- a/Source/Doc/UserGuide.md
+++ b/Source/Doc/UserGuide.md
@@ -58,8 +58,9 @@ produced by these developer communities:

 General features include:

+* Z80 Family CPUs including Z80, Z180, and Z280
 * Banked memory services for several banking designs
-* Disk drivers for RAM, ROM, Floppy, IDE, CF, and SD
+* Disk drivers for RAM, ROM, Floppy, IDE ATA/ATAPI, CF, SD, Zip, Iomega
 * Serial drivers including UART (16550-like), ASCI, ACIA, SIO
 * Video drivers including TMS9918, SY6545, MOS8563, HD6445
 * Keyboard (PS/2) drivers via VT8242 or PPI interfaces
@@ -195,6 +196,7 @@ below, **carefully** pick the appropriate ROM image for your hardware.
 | [Small Computer SC131 Z180 Pocket Computer]^5^                 | -       | SCZ180_sc131.rom   | 115200        |
 | [Small Computer SC140 Z180 CPU Module]^5^                      | Z50     | SCZ180_sc140.rom   | 115200        |
 | [Small Computer SC503 Z180 CPU Module]^5^                      | Z50     | SCZ180_sc503.rom   | 115200        |
+| [Small Computer SC700 Z180 CPU Module]^5^                      | RCBus   | SCZ180_sc700.rom   | 115200        |
 | [Dyno Z180 SBC]^6^                                             | Dyno    | DYNO_std.rom       | 38400         |
 | [Nhyodyne Z80 MBC]^1^                                          | MBC     | MBC_std.rom        | 38400         |
 | [Rhyophyre Z180 SBC]^1^                                        | -       | RPH_std.rom        | 38400         |
@@ -204,6 +206,7 @@ below, **carefully** pick the appropriate ROM image for your hardware.
 | [Z80-Retro SBC]^8^                                             | -       | Z80RETRO_std.rom   | 38400         |
 | [S100 Computers Z180]^9^                                       | S100    | S100_std.rom       | 38400         |
 | [Duodyne Z80 System]^1^                                        | Duo     | DUO_std.rom        | 38400         |
+| [Heath H8 Z80 System]                                          | H8      | HEATH_std.rom      | 115200        |

 | ^1^Designed by Andrew Lynch
 | ^2^Designed by Sergey Kiselev
@@ -1534,7 +1537,46 @@ indicated:
 You will notice that there are actually 2 combo disk images in the 
 distribution.  One for an hd512 disk layout (hd512_combo.img) and one 
 for an hd1k disk layout (hd1k_combo.img). Simply use the image file that
-corresponds to your desired hard disk layout.
+corresponds to your desired hard disk layout.  Review the information
+in [Hard Disk Layouts] if you need more information of the disk layout
+options.
+
+The partition table in the combo disk images includes an entry for a
+FAT filesystem starting at 512K with a size of 384K.  So when using
+the combo disk image, by default, your disk will have the first 512K
+dedicated to CP/M slices followed by 384K for a FAT filesystem.  Note
+that the pre-allocated FAT partition must still be formatted using
+`FDISK32` in order to actually use it
+(see [FAT Filesystem Preparation]).
+
+The combo disk image layout was designed to fit well on a 1GB hard
+disk.  The 512K of CP/M slices and 384K of FAT filesystem all fit inside
+a 1GB hard disk.  This size choice was a bit arbitrary, but based on the
+idea that a 1GB CF or SD Card is easy and cheap to acquire.  It is fine
+if your hard disk is smaller than 1GB.  It just means that it will not
+be possible to use the pre-allocated FAT filesystem partition (you will
+get I/O errors if you attempt to do so).
+
+The 512KB area of the combo disk image set aside for slices can contain
+approximately 64 slices (8MB per slice).  If your actual hard disk is
+less than 512KB, then this will correspondingly reduce the number of
+possible slices.  If your hard disk is smaller than 64MB, then you
+will find that some of the higher drive letters do not work because
+they exist "off the end" of the hard disk.
+
+For RomWBW systems with a single hard disk (typical), you will notice 
+that an OS will pre-allocate 8 drive letters to the hard disk.  If the 
+combo disk image is being used, only the first 6 drive letters (A: - H:)
+will have any content because the combo disk image only provides 6 
+slices. The subsequent drives (I: - J:) will have no content and will 
+not be pre-initialized.  If you want to use any slices beyond the first 
+6, you must initialize them using `CLRDIR` first.
+
+A great way to maintain your own data on a hard disk is to put this
+data in slices beyond the first 6.  By doing so, you can always
+"reimage" your drive with the combo image without overlaying the data
+stored in the slices beyond the first 6.  Just be very careful to use
+the same combo image (hd512 or hd1k) as you used originally.

 #### Custom Hard Disk Image

@@ -2143,10 +2185,36 @@ regarding the RomWBW adaptation and customizations.

 #### Boot Disk

-There is no RomWBW-specific boot disk creation procedure.  QP/M
-comes with a QINSTALL which is used to install QPM over an existing
-CP/M 2 installation or to update an existing QPM disk.  `QINSTALL.COM`
-is included with the RomWBW distribution.
+
+To create or update a bootable QP/M Z-System disk, a special process
+is required.  QP/M is not provided in source format.  You are expected
+to install QP/M over an existing CP/M installation using the
+`QINSTALL.COM` application.
+
+To update an existing QP/M boot disk with the latest RomWBW CBIOS, you
+must use 2 steps: apply the generic CP/M system track, then reinstall
+the QP/M components.  To do this, you can perform the following steps:
+
+1. Boot to the existing QP/M disk.  At this point, drive A should be
+   the QP/M disk that you wish to update.  You may receive a warning
+   about CBIOS/HBIOS version mismatch.
+
+1. Use RomWBW `SYSCOPY` to place the stock RomWBW CP/M OS image
+   onto the system tracks of the QP/M boot disk:
+   
+   `SYSCOPY A:=x:CPM.SYS`
+   
+   where x is the drive letter of your ROM Disk.
+
+1. Run `QINSTALL` to overlay the QP/M OS components on your
+   QP/M boot disk.
+
+**WARNING**: `QINSTALL` has no mechanism for retaining previous
+non-default settings.  Any previous non-default settings you
+previously made with `QINSTALL` will need to be reapplied.  The
+pre-built RomWBW QP/M disk image includes a couple of specific
+non-default settings to optimize use with RomWBW.  Please review the
+notes in the ReadMe.txt file in Source/Images/d_qpm.

 #### Notes

@@ -2154,6 +2222,9 @@ is included with the RomWBW distribution.
  on the QPM binary distribution and has been minimally customized
  for RomWBW.

+- When booted, the QPM startup banner will indicate CP/M 2.2.  This
+  is because QPM uses the CP/M 2.2 CBIOS code.
+
 - QINSTALL is used to customize QPM.  It is included on the
  disk image.  You should review the notes in the ReadMe.txt
  file in Source/Images/d_qpm before making changes.
@@ -3791,6 +3862,31 @@ the RomWBW HBIOS configuration.

 `\clearpage`{=latex}

+### Small Computer SC700 Z180 CPU Module
+
+|                   |                  |
+|-------------------|------------------|
+| ROM Image Files   | SCZ180_sc700.rom |
+| Console Baud Rate | 115200           |
+| Interrupts        | Mode 2           |
+
+ - CPU speed is detected at startup if DS1302 RTC is active
+   - Otherwise 18.432 MHz assumed
+ - System timer is generated by Z180 CPU
+ - Hardware auto-detected:
+   - DS1302 RTC
+   - Z180 ASCI Serial Ports
+   - SIO Serial Interface Module
+   - EP Dual UART Serial Interface Module
+   - WDC Floppy Disk Controller w/ 3.5" HD Drives
+   - IDE Hard Disk Interface Module
+   - PPIDE Hard Disk Interface Module
+   - Onboard SD Card Interface
+ - Use of Interrupt Mode 2 requires proper IEI/IEO configuration
+   for all peripherals generating interrupts
+
+`\clearpage`{=latex}
+
 ### Dyno Z180 SBC

 |                   |                |
@@ -3979,6 +4075,29 @@ the RomWBW HBIOS configuration.

 `\clearpage`{=latex}

+### Heath H8 Z80 System
+
+|                   |               |
+|-------------------|---------------|
+| ROM Image File    | HEATH_std.rom |
+| Console Baud Rate | 115200        |
+| Interrupts        | Mode 1        |
+
+ - CPU speed is detected at startup if DS1302 RTC is active
+   - Otherwise 7.3728 MHz assumed
+ - Hardware auto-detected:
+   - DS1302 RTC
+   - ACIA Serial Interface Module
+   - SIO Serial Interface Module
+   - EP Dual UART Serial Interface Module
+   - WDC Floppy Disk Controller w/ 3.5" HD Drives
+   - IDE Hard Disk Interface Module
+   - PPIDE Hard Disk Interface Module
+ - Serial baud rate is usually determined by hardware for ACIA and
+   SIO interfaces
+
+`\clearpage`{=latex}
+
 ## Appendix B - Device Summary

 The table below briefly describes each of the possible devices that
@@ -4001,7 +4120,7 @@ may be discovered by RomWBW in your system.
 | FD        | Disk     | 8272 or compatible Floppy Disk Controller              |
 | GDC       | Video    | uPD7220 Video Display Controller                       |
 | HDSK      | Disk     | SIMH Simulator Hard Disk                               |
-| IDE       | Disk     | IDE/ATA Hard Disk Interface                            |
+| IDE       | Disk     | IDE/ATA/ATAPI Hard Disk Interface                      |
 | ICM       | DsKy     | ICM7218-based Display/Keypad on PPI                    |
 | IMM       | Disk     | IMM Zip Drive on PPI                                   |
 | INTRTC    | RTC      | Interrupt-based Real Time Clock                        |
@@ -4013,7 +4132,7 @@ may be discovered by RomWBW in your system.
 | I2C       | System   | I2C Interface                                          |
 | PIO       | Char     | Zilog Parallel Interface Controller                    |
 | PKD       | DsKy     | P8279-based Display/Keypad on PPI                      |
-| PPIDE     | Disk     | 8255 IDE/ATA Hard Disk Interface                       |
+| PPIDE     | Disk     | 8255 IDE/ATA/ATAPI Hard Disk Interface                 |
 | PPA       | Disk     | PPA Zip Drive on PPI                                   |
 | PPK       | Kbd      | Matrix Keyboard                                        |
 | PPPSD     | Disk     | ParPortProp SD Card Interface                          |
--- a/Source/HBIOS/Bank
+++ b/Source/HBIOS/Bank
@@ -0,0 +1,74 @@
+ROM Bank Layout
+
+Bank ID		Module		Start	Size
+------		------		------	------
+0x00		hbios		0x0000	0x8000
+		<end>		0x8000
+
+0x01		loader		0x0000	0x1000
+		dbgmon		0x1000	0x2000
+		cpm22		0x2000	0x3000
+		zsys		0x5000	0x3000
+		<end>		0x8000
+
+0x02		forth		0x0000	0x1700
+		basic		0x1700	0x2000
+		tbasic		0x3700	0x0900
+		game		0x4000	0x0900
+		egg		0x4900	0x0200
+		netboot         0x4B00	0x1000
+		updater         0x5B00	0x0D00
+		usrrom		0x6800	0x1800
+		<end>		0x8000
+
+0x03		imgpad2		0x0000	0x8000
+		<end>		0x8000
+
+0x04 - N	ROM Disk Data
+
+
+RAM Bank Layout
+
+Bank ID         Usage
+-------         ------
+0x80            RomWBW HBIOS
+0x81-0x8B       RAM Disk Data
+0x8C		CP/M 3 Buffers
+0x8D            CP/M 3 OS
+0x8E            User TPA
+0x8F            Common
+
+
+ROMless Bank Layout
+
+Bank ID         Usage
+-------         ------
+0x80            RomWBW HBIOS
+0x81		Loader, DbgMon, CP/M 2.2, ZSDOS
+0x82		ROM Apps
+0x83		More ROM Apps
+0x84-0x8B       RAM Disk Data
+0x8C		CP/M 3 Buffers
+0x8D            CP/M 3 OS
+0x8E            User TPA
+0x8F            Common
+
+
+ROMless Tiny Bank Layout (128K)
+NOTE: no ROM Apps, no CP/M 3 support, no RAM disk
+
+Bank ID         Usage
+-------         ------
+0x80            RomWBW HBIOS
+0x81		Loader, DbgMon, CP/M 2.2, ZSDOS
+0x82            User TPA
+0x83            Common
+
+Disk Image Sizes
+
+Image Size	ROM System	ROMless System
+----------	----------	--------------
+1024K		896K		768K
+512		384K		256K
+256		128K		0K
+128 (tiny)	n/a		0K
--- a/Source/HBIOS/Build.cmd
+++ b/Source/HBIOS/Build.cmd
@@ -110,10 +110,8 @@ copy /b romldr.bin + dbgmon.bin + ..\zsdos\zsys_wbw.bin osimg_small.bin || exit
 :: should yield a result of zero.
 ::

-if %ROMSize% gtr 0 (
-    for %%f in (hbios_rom.bin osimg.bin osimg1.bin osimg2.bin) do (
-      "%TOOLS%\srecord\srec_cat.exe" %%f -Binary -Crop 0 0x7FFF -Checksum_Negative_Big_Endian 0x7FFF 1 1 -o %%f -Binary || exit /b
-    )
+for %%f in (hbios_rom.bin osimg.bin osimg1.bin osimg2.bin) do (
+  "%TOOLS%\srecord\srec_cat.exe" %%f -Binary -Crop 0 0x7FFF -Checksum_Negative_Big_Endian 0x7FFF 1 1 -o %%f -Binary || exit /b
 )

 ::
@@ -137,8 +135,8 @@ if %ROMSize% gtr 0 (
    copy /b hbios_rom.bin + osimg.bin + osimg1.bin + osimg2.bin %ROMName%.upd || exit /b
    copy /b hbios_app.bin + osimg_small.bin %ROMName%.com || exit /b
 ) else (
-    copy /b hbios_rom.bin + osimg_small.bin %ROMName%.rom || exit /b
-    copy /b hbios_rom.bin + osimg_small.bin %ROMName%.upd || exit /b
+    copy /b hbios_rom.bin + osimg.bin + osimg1.bin + osimg2.bin  + ..\RomDsk\ram%ROMSize%_wbw.dat %ROMName%.rom || exit /b
+    copy /b hbios_rom.bin + osimg.bin + osimg1.bin + osimg2.bin %ROMName%.upd || exit /b
    copy /b hbios_app.bin + osimg_small.bin %ROMName%.com || exit /b
 )

@@ -222,16 +220,19 @@ call Build RCZ280 ext || exit /b
 call Build RCZ280 nat || exit /b
 call Build RCZ280 zz80mb || exit /b
 call Build RCZ280 zzrc || exit /b
+call Build RCZ280 zzrc_ram || exit /b
 call Build SCZ180 sc126 || exit /b
 call Build SCZ180 sc130 || exit /b
 call Build SCZ180 sc131 || exit /b
 call Build SCZ180 sc140 || exit /b
 call Build SCZ180 sc503 || exit /b
+call Build SCZ180 sc700 || exit /b
 call Build DYNO std || exit /b
 call Build UNA std || exit /b
 call Build RPH std || exit /b
 call Build Z80RETRO std || exit /b
 call Build S100 std || exit /b
 call Build DUO std || exit /b
+call Build HEATH std || exit /b

 goto :eof
--- a/Source/HBIOS/Build.ps1
+++ b/Source/HBIOS/Build.ps1
@@ -27,7 +27,7 @@ $ErrorAction = 'Stop'
 # UNA BIOS is simply imbedded, it is not built here.
 #

-$PlatformListZ80 = "SBC", "MBC", "ZETA", "ZETA2", "RCZ80", "Z80RETRO", "DUO", "UNA"
+$PlatformListZ80 = "SBC", "MBC", "ZETA", "ZETA2", "RCZ80", "Z80RETRO", "DUO", "UNA", "HEATH"
 $PlatformListZ180 = "N8", "MK4", "RCZ180", "SCZ180", "DYNO", "RPH", "S100"
 $PlatformListZ280 = "RCZ280"

--- a/Source/HBIOS/Build.sh
+++ b/Source/HBIOS/Build.sh
@@ -19,6 +19,7 @@ if [ "${ROM_PLATFORM}" == "dist" ] ; then
 	ROM_PLATFORM="RCZ280"; ROM_CONFIG="nat"; bash Build.sh
 	ROM_PLATFORM="RCZ280"; ROM_CONFIG="zz80mb"; bash Build.sh
 	ROM_PLATFORM="RCZ280"; ROM_CONFIG="zzrc"; bash Build.sh
+	ROM_PLATFORM="RCZ280"; ROM_CONFIG="zzrc_ram"; bash Build.sh
 #	ROM_PLATFORM="RCZ80"; ROM_CONFIG="mt"; bash Build.sh
 #	ROM_PLATFORM="RCZ80"; ROM_CONFIG="duart"; bash Build.sh
 	ROM_PLATFORM="RCZ80"; ROM_CONFIG="std"; bash Build.sh
@@ -38,11 +39,13 @@ if [ "${ROM_PLATFORM}" == "dist" ] ; then
 	ROM_PLATFORM="SCZ180"; ROM_CONFIG="sc131"; bash Build.sh
 	ROM_PLATFORM="SCZ180"; ROM_CONFIG="sc140"; bash Build.sh
 	ROM_PLATFORM="SCZ180"; ROM_CONFIG="sc503"; bash Build.sh
+	ROM_PLATFORM="SCZ180"; ROM_CONFIG="sc700"; bash Build.sh
 	ROM_PLATFORM="S100"; ROM_CONFIG="std"; bash Build.sh
 	ROM_PLATFORM="UNA"; ROM_CONFIG="std"; bash Build.sh
 	ROM_PLATFORM="Z80RETRO"; ROM_CONFIG="std"; bash Build.sh
 	ROM_PLATFORM="ZETA"; ROM_CONFIG="std"; bash Build.sh
 	ROM_PLATFORM="ZETA2"; ROM_CONFIG="std"; bash Build.sh
+	ROM_PLATFORM="HEATH"; ROM_CONFIG="std"; bash Build.sh
 	exit
 fi

--- a/Source/HBIOS/Config/DUO_std.asm
+++ b/Source/HBIOS/Config/DUO_std.asm
@@ -44,3 +44,5 @@ MDFFENABLE	.SET	FALSE		; MD: ENABLE FLASH FILE SYSTEM
 ;
 UARTINTS	.SET	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 ;UARTCFG	.SET	UARTCFG | SER_RTS
+;
+ESPENABLE	.SET	TRUE		; ESP: ENABLE ESP32 IO BOARD DRIVER (ESP.ASM)
--- a/Source/HBIOS/Config/HEATH_std.asm
+++ b/Source/HBIOS/Config/HEATH_std.asm
@@ -0,0 +1,69 @@
+;
+;==================================================================================================
+;   HEATH H8 Z80 STANDARD CONFIGURATION
+;==================================================================================================
+;
+; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
+; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
+; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
+; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
+; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
+; YOUR FILE IN THE BUILD PROCESS.
+;
+; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
+; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
+; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
+; SETTINGS.
+;
+; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
+; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
+; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
+; DIRECTORIES ABOVE THIS ONE).
+;
+#DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
+;
+#include "cfg_rcz80.asm"
+;
+CPUOSC		.SET	7372800		; CPU OSC FREQ IN MHZ
+CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
+;
+DSKYENABLE	.SET	TRUE		; ENABLES DSKY FUNCTIONALITY
+H8PENABLE	.SET	TRUE		; ENABLES HEATH H8 FRONT PANEL
+;
+FPLED_ENABLE	.SET	TRUE		; FP: ENABLES FRONT PANEL LEDS
+FPSW_ENABLE	.SET	TRUE		; FP: ENABLES FRONT PANEL SWITCHES
+;
+DSRTCENABLE	.SET	TRUE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
+RP5RTCENABLE	.SET	FALSE		; RP5C01 RTC BASED CLOCK (RP5RTC.ASM)
+;
+UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+ACIAENABLE	.SET	TRUE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
+SIOENABLE	.SET	TRUE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
+DUARTENABLE	.SET	FALSE		; DUART: ENABLE 2681/2692 SERIAL DRIVER (DUART.ASM)
+;
+LPTENABLE	.SET	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
+;
+TMSENABLE	.SET	FALSE		; TMS: ENABLE TMS9918 VIDEO/KBD DRIVER (TMS.ASM)
+TMSTIMENABLE	.SET	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
+TMSMODE		.SET	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MSXKBD|COLECO]
+MKYENABLE	.SET	FALSE		; MSX 5255 PPI KEYBOARD COMPATIBLE DRIVER (REQUIRES TMS VDA DRIVER)
+VRCENABLE	.SET	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+VDAEMU_SERKBD	.SET	0		; VDA EMULATION: SERIAL KBD UNIT #, OR $FF FOR HW KBD
+;
+AY38910ENABLE	.SET	FALSE		; AY: AY-3-8910 / YM2149 SOUND DRIVER
+AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LINC]
+SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
+;
+FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
+;
+IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
+PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
+SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
+SDMODE		.SET	SDMODE_PIO	; SD: DRIVER MODE: SDMODE_[JUHA|N8|CSIO|PPI|UART|DSD|MK4|SC|MT|PIO|USR]
+SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
+IMMENABLE	.SET	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+;
+PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
--- a/Source/HBIOS/Config/MK4_std.asm
+++ b/Source/HBIOS/Config/MK4_std.asm
@@ -47,7 +47,7 @@ VGAENABLE	.SET	TRUE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VDAEMU_SERKBD	.SET	0		; VDA EMULATION: SERIAL KBD UNIT #, OR $FF FOR HW KBD
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_DIDE	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_DIDE	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ180_ext.asm
+++ b/Source/HBIOS/Config/RCZ180_ext.asm
@@ -58,7 +58,7 @@ AYMODE		.SET	AYMODE_RCZ180	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LI
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ180_nat.asm
+++ b/Source/HBIOS/Config/RCZ180_nat.asm
@@ -57,7 +57,7 @@ AYMODE		.SET	AYMODE_RCZ180	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LI
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ280_ext.asm
+++ b/Source/HBIOS/Config/RCZ280_ext.asm
@@ -56,7 +56,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ280_nat.asm
+++ b/Source/HBIOS/Config/RCZ280_nat.asm
@@ -56,7 +56,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ280_zz80mb.asm
+++ b/Source/HBIOS/Config/RCZ280_zz80mb.asm
@@ -37,8 +37,7 @@ FPSW_ENABLE	.SET	TRUE		; FP: ENABLES FRONT PANEL SWITCHES
 ;
 MEMMGR		.SET	MM_Z280		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280]
 ;
-RAMLOC		.SET	23		; START OF RAM AS POWER OF 2 (2^N) IN PHYSICAL ADDRESS SPACE
-RAMBIAS		.SET	(1 << (RAMLOC - 10))	; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
+RAMBIAS		.SET	8192		; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
 ;
 Z280_MEMLOWAIT	.SET	0		; Z280: LOW 8MB MEMORY WAIT STATES (0-3)
 Z280_MEMHIWAIT	.SET	0		; Z280: HIGH 8MB MEMORY WAIT STATES (0-3)
@@ -62,7 +61,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ280_zzrc.asm
+++ b/Source/HBIOS/Config/RCZ280_zzrc.asm
@@ -39,10 +39,7 @@ MEMMGR		.SET	MM_Z280		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280]
 ;
 RAMSIZE		.SET	256		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.SET	256		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
-ROMSIZE_CHK	.SET	256		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
-;
-RAMLOC		.SET	18		; START OF RAM AS POWER OF 2 (2^N) IN PHYSICAL ADDRESS SPACE
-RAMBIAS		.SET	(1 << (RAMLOC - 10))	; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
+RAMBIAS		.SET	ROMSIZE		; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
 ;
 Z280_MEMLOWAIT	.SET	0		; Z280: LOW 8MB MEMORY WAIT STATES (0-3)
 Z280_MEMHIWAIT	.SET	0		; Z280: HIGH 8MB MEMORY WAIT STATES (0-3)
@@ -70,7 +67,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ280_zzrc_ram.asm
+++ b/Source/HBIOS/Config/RCZ280_zzrc_ram.asm
@@ -0,0 +1,77 @@
+;
+;==================================================================================================
+;   RCBUS Z280 STANDARD CONFIGURATION (NATIVE Z280 MMU W/ LINEAR MEMORY ON ZZRC)
+;==================================================================================================
+;
+; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
+; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
+; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
+; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
+; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
+; YOUR FILE IN THE BUILD PROCESS.
+;
+; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
+; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
+; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
+; SETTINGS.
+;
+; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
+; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
+; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
+; DIRECTORIES ABOVE THIS ONE).
+;
+#DEFINE PLATFORM_NAME "ZZRC", " [", CONFIG, "]"
+;
+#DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
+;
+#include "cfg_rcz280.asm"
+;
+CPUOSC		.SET	14745600	; CPU OSC FREQ IN MHZ
+INTMODE		.SET	3		; INTERRUPTS: 0=NONE, 1=MODE 1, 2=MODE 2
+CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
+;
+FPLED_ENABLE	.SET	TRUE		; FP: ENABLES FRONT PANEL LEDS
+FPSW_ENABLE	.SET	TRUE		; FP: ENABLES FRONT PANEL SWITCHES
+;
+MEMMGR		.SET	MM_Z280		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280]
+;
+RAMSIZE		.SET	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
+ROMSIZE		.SET	0		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
+RAMBIAS		.SET	ROMSIZE		; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
+;
+Z280_MEMLOWAIT	.SET	0		; Z280: LOW 8MB MEMORY WAIT STATES (0-3)
+Z280_MEMHIWAIT	.SET	0		; Z280: HIGH 8MB MEMORY WAIT STATES (0-3)
+Z280_IOWAIT	.SET	1		; Z280: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
+Z280_INTWAIT	.SET	0		; Z280: INT ACK WAIT STATUS (0-3)
+;
+MDROM		.SET	FALSE		; MD: ENABLE ROM DISK
+MDRAM		.SET	TRUE		; MD: ENABLE RAM DISK
+;
+Z2UENABLE	.SET	TRUE		; Z2U: ENABLE Z280 UART SERIAL DRIVER (Z2U.ASM)
+Z2UOSC		.SET	(CPUOSC / 8)	; Z2U: OSC FREQUENCY IN MHZ
+Z2U0HFC		.SET	TRUE		; Z2U0: ENABLE HARDWARE FLOW CONTROL
+UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+ACIAENABLE	.SET	FALSE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
+SIOENABLE	.SET	TRUE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
+;
+TMSENABLE	.SET	FALSE		; TMS: ENABLE TMS9918 VIDEO/KBD DRIVER (TMS.ASM)
+TMSMODE		.SET	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MSXKBD|COLECO]
+MKYENABLE	.SET	FALSE		; MSX 5255 PPI KEYBOARD COMPATIBLE DRIVER (REQUIRES TMS VDA DRIVER)
+VRCENABLE	.SET	TRUE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+VDAEMU_SERKBD	.SET	$FF		; VDA EMULATION: SERIAL KBD UNIT #, OR $FF FOR HW KBD
+;
+AY38910ENABLE	.SET	FALSE		; AY: AY-3-8910 / YM2149 SOUND DRIVER
+AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LINC]
+SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
+;
+FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
+;
+IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
+PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
+SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
+SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
+;
+PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
--- a/Source/HBIOS/Config/RCZ80_easy.asm
+++ b/Source/HBIOS/Config/RCZ80_easy.asm
@@ -41,6 +41,7 @@ WDOGIO		.SET	$6F		; WATCHDOG REGISTER ADR
 ;
 DSRTCENABLE	.SET	TRUE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
 RP5RTCENABLE	.SET	FALSE		; RP5C01 RTC BASED CLOCK (RP5RTC.ASM)
+INTRTCENABLE	.SET	TRUE		; ENABLE PERIODIC INTERRUPT CLOCK DRIVER (INTRTC.ASM)
 ;
 CTCENABLE	.SET	TRUE		; ENABLE ZILOG CTC SUPPORT
 CTCTIMER	.SET	TRUE		; ENABLE CTC PERIODIC TIMER
@@ -69,7 +70,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ80_jbl.asm
+++ b/Source/HBIOS/Config/RCZ80_jbl.asm
@@ -69,7 +69,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	TRUE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	FALSE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ80_kio.asm
+++ b/Source/HBIOS/Config/RCZ80_kio.asm
@@ -66,7 +66,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ80_skz.asm
+++ b/Source/HBIOS/Config/RCZ80_skz.asm
@@ -61,7 +61,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ80_std.asm
+++ b/Source/HBIOS/Config/RCZ80_std.asm
@@ -54,7 +54,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ80_tiny.asm
+++ b/Source/HBIOS/Config/RCZ80_tiny.asm
@@ -75,7 +75,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 IDE0BASE	.SET	$90		; IDE 0: IO BASE ADDRESS
--- a/Source/HBIOS/Config/RCZ80_zrc.asm
+++ b/Source/HBIOS/Config/RCZ80_zrc.asm
@@ -53,7 +53,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/RCZ80_zrc_ram.asm
+++ b/Source/HBIOS/Config/RCZ80_zrc_ram.asm
@@ -34,7 +34,7 @@ CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
 FPLED_ENABLE	.SET	TRUE		; FP: ENABLES FRONT PANEL LEDS
 FPSW_ENABLE	.SET	TRUE		; FP: ENABLES FRONT PANEL SWITCHES
 ;
-RAMSIZE		.SET	2048		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
+RAMSIZE		.SET	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.SET	0		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
 MEMMGR		.SET	MM_ZRC		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180]
 ;
@@ -57,7 +57,7 @@ AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LIN
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/S100_std.asm
+++ b/Source/HBIOS/Config/S100_std.asm
@@ -27,18 +27,17 @@
 #include "cfg_s100.asm"
 ;
 CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
+CRTACT		.SET	TRUE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
 ;
 Z180_CLKDIV	.SET	1		; Z180: CHK DIV: 0=OSC/2, 1=OSC, 2=OSC*2
-Z180_MEMWAIT	.SET	0		; Z180: MEMORY WAIT STATES (0-3)
-Z180_IOWAIT	.SET	1		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
+Z180_MEMWAIT	.SET	1		; Z180: MEMORY WAIT STATES (0-3)
+Z180_IOWAIT	.SET	2		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
 ;
 DSRTCENABLE	.SET	FALSE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
 INTRTCENABLE	.SET	TRUE		; ENABLE PERIODIC INTERRUPT CLOCK DRIVER (INTRTC.ASM)
 ;
-UARTENABLE	.SET	FALSE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 ASCIENABLE	.SET	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
-ACIAENABLE	.SET	FALSE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
-SIOENABLE	.SET	FALSE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
+SCONENABLE	.SET	TRUE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 IDEENABLE	.SET	FALSE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/SBC_std.asm
+++ b/Source/HBIOS/Config/SBC_std.asm
@@ -45,7 +45,7 @@ VGAENABLE	.SET	TRUE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VDAEMU_SERKBD	.SET	0		; VDA EMULATION: SERIAL KBD UNIT #, OR $FF FOR HW KBD
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_DIO3	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_DIO3	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	FALSE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/SCZ180_sc126.asm
+++ b/Source/HBIOS/Config/SCZ180_sc126.asm
@@ -59,7 +59,7 @@ AYMODE		.SET	AYMODE_RCZ180	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LI
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/SCZ180_sc130.asm
+++ b/Source/HBIOS/Config/SCZ180_sc130.asm
@@ -60,7 +60,7 @@ AYMODE		.SET	AYMODE_RCZ180	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LI
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/SCZ180_sc140.asm
+++ b/Source/HBIOS/Config/SCZ180_sc140.asm
@@ -54,7 +54,7 @@ AYMODE		.SET	AYMODE_LINC	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LINC
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/SCZ180_sc503.asm
+++ b/Source/HBIOS/Config/SCZ180_sc503.asm
@@ -54,7 +54,7 @@ AYMODE		.SET	AYMODE_LINC	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LINC
 SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
 PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
--- a/Source/HBIOS/Config/SCZ180_sc700.asm
+++ b/Source/HBIOS/Config/SCZ180_sc700.asm
@@ -0,0 +1,71 @@
+;
+;==================================================================================================
+;   SC700 STANDARD CONFIGURATION
+;==================================================================================================
+;
+; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
+; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
+; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
+; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
+; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
+; YOUR FILE IN THE BUILD PROCESS.
+;
+; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
+; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
+; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
+; SETTINGS.
+;
+; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
+; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
+; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
+; DIRECTORIES ABOVE THIS ONE).
+;
+#DEFINE PLATFORM_NAME "Small Computer SC700", " [", CONFIG, "]"
+;
+#DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
+;
+#include "cfg_scz180.asm"
+;
+CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
+CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
+;
+Z180_CLKDIV	.SET	1		; Z180: CHK DIV: 0=OSC/2, 1=OSC, 2=OSC*2
+Z180_MEMWAIT	.SET	0		; Z180: MEMORY WAIT STATES (0-3)
+Z180_IOWAIT	.SET	1		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
+;
+LEDENABLE	.SET	TRUE		; ENABLE STATUS LED (SINGLE LED)
+LEDPORT		.SET	$0E		; STATUS LED PORT ADDRESS
+;
+FPLED_ENABLE	.SET	TRUE		; FP: ENABLES FRONT PANEL LEDS
+FPLED_IO	.SET	$00		; FP: PORT ADDRESS FOR FP LEDS
+;
+DSRTCENABLE	.SET	TRUE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
+INTRTCENABLE	.SET	TRUE		; ENABLE PERIODIC INTERRUPT CLOCK DRIVER (INTRTC.ASM)
+;
+UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+ASCIENABLE	.SET	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
+ACIAENABLE	.SET	FALSE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
+SIOENABLE	.SET	TRUE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
+;
+TMSENABLE	.SET	FALSE		; TMS: ENABLE TMS9918 VIDEO/KBD DRIVER (TMS.ASM)
+TMSTIMENABLE	.SET	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
+TMSMODE		.SET	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MSXKBD|COLECO]
+MKYENABLE	.SET	FALSE		; MSX 5255 PPI KEYBOARD COMPATIBLE DRIVER (REQUIRES TMS VDA DRIVER)
+VDAEMU_SERKBD	.SET	0		; VDA EMULATION: SERIAL KBD UNIT #, OR $FF FOR HW KBD
+;
+AY38910ENABLE	.SET	TRUE		; AY: AY-3-8910 / YM2149 SOUND DRIVER
+AYMODE		.SET	AYMODE_RCZ180	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LINC]
+SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
+;
+FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+;
+IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
+PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
+SDENABLE	.SET	TRUE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
+SDMODE		.SET	SDMODE_SC	; SD: DRIVER MODE: SDMODE_[JUHA|N8|CSIO|PPI|UART|DSD|MK4|SC|MT|USR]
+SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD & SC ONLY
+;
+PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
--- a/Source/HBIOS/Config/ZETA2_std.asm
+++ b/Source/HBIOS/Config/ZETA2_std.asm
@@ -35,7 +35,7 @@ UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 UARTSBC		.SET	TRUE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_ZETA2	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_ZETA2	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 PPIDEENABLE	.SET	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
--- a/Source/HBIOS/Config/ZETA_std.asm
+++ b/Source/HBIOS/Config/ZETA_std.asm
@@ -35,7 +35,7 @@ UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 UARTSBC		.SET	TRUE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
 ;
 FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_ZETA	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+FDMODE		.SET	FDMODE_ZETA	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
 ;
 PPIDEENABLE	.SET	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
 SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
--- a/Source/HBIOS/Makefile
+++ b/Source/HBIOS/Makefile
@@ -67,11 +67,9 @@ $(OBJECTS) : $(ROMDEPS)
 		else \
 			cat imgpad2.bin >osimg2.bin ; \
 		fi ; \
-		if [ $(ROMSIZE) -gt 0 ] ; then \
-			for f in hbios_rom.bin osimg.bin osimg1.bin osimg2.bin ; do \
-				srec_cat $$f -Binary -Crop 0 0x7FFF -Checksum_Negative_Big_Endian 0x7FFF 1 1 -o $$f -Binary ; \
-			done \
-		fi \
+		for f in hbios_rom.bin osimg.bin osimg1.bin osimg2.bin ; do \
+			srec_cat $$f -Binary -Crop 0 0x7FFF -Checksum_Negative_Big_Endian 0x7FFF 1 1 -o $$f -Binary ; \
+		done \
 	fi
 	if [ $(ROM_PLATFORM) = UNA ] ; then \
 		cp osimg.bin $(DEST)/UNA_WBW_SYS.bin ; \
@@ -83,8 +81,8 @@ $(OBJECTS) : $(ROMDEPS)
 			cat hbios_rom.bin osimg.bin osimg1.bin osimg2.bin >$(ROMNAME).upd ; \
 			cat hbios_app.bin osimg_small.bin > $(ROMNAME).com ; \
 		else \
-			cat hbios_rom.bin osimg_small.bin > $(ROMNAME).rom ; \
-			cat hbios_rom.bin osimg_small.bin > $(ROMNAME).upd ; \
+			cat hbios_rom.bin osimg.bin osimg1.bin osimg2.bin >$(ROMNAME).rom ; \
+			cat hbios_rom.bin osimg.bin osimg1.bin osimg2.bin >$(ROMNAME).upd ; \
 			cat hbios_app.bin osimg_small.bin > $(ROMNAME).com ; \
 		fi \
 	fi
--- a/Source/HBIOS/ROM
+++ b/Source/HBIOS/ROM
@@ -1,39 +0,0 @@
-RomWBW ROM Layout
-
-Bank		Module		Start	Size
------		------		------	------		
-0		hbios		0x0000	0x8000
-		<end>		0x8000
-
-1		loader		0x0000	0x1000
-		dbgmon		0x1000	0x2000
-		cpm22		0x2000	0x3000
-		zsys		0x5000	0x3000
-		<end>		0x8000        
-
-2		forth		0x0000	0x1700
-		basic		0x1700	0x2000
-		tbasic		0x3700	0x0900
-		game		0x4000	0x0900
-		egg		0x4900	0x0200
-		netboot         0x4B00	0x1000
-		updater         0x5B00	0x0D00
-		usrrom		0x6800	0x1800
-		<end>		0x8000
-
-3		imgpad2		0x0000	0x8000
-		<end>		0x8000
-
-4 - N		ROM Disk Data
-
-
-RomWBW RAM Layout
-
-Bank ID         Usage                   Physical Address
-------         ------                  ----------------
-0x80-0x87       RAM Disk Data           0x80000-0xBFFFF
-0x88-0x8B       CP/M 3 Buffers          0xC0000-0xDFFFF
-0x8C            CP/M 3 OS               0xE0000-0xE7FFF
-0x8D            RomWBW HBIOS            0xE8000-0xEFFFF
-0x8E            User TPA                0xF0000-0xF7FFF
-0x8F            Common                  0xF8000-0xFFFFF
--- a/Source/HBIOS/cfg_duo.asm
+++ b/Source/HBIOS/cfg_duo.asm
@@ -15,7 +15,7 @@
 ;
 #INCLUDE "hbios.inc"
 ;
-PLATFORM	.EQU	PLT_DUO		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO]
+PLATFORM	.EQU	PLT_DUO		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
 CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
@@ -34,7 +34,6 @@ DEFSERCFG	.EQU	SER_38400_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
 ;
 RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
-ROMSIZE_CHK	.EQU	0		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
 MEMMGR		.EQU	MM_Z2		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
 MPGSEL_0	.EQU	$50		; Z2 MEM MGR BANK 0 PAGE SELECT REG (WRITE ONLY)
 MPGSEL_1	.EQU	$51		; Z2 MEM MGR BANK 1 PAGE SELECT REG (WRITE ONLY)
@@ -86,6 +85,7 @@ ICMPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF ICM PPI
 PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
 PKDPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF PKD PPI
 PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
+H8PENABLE	.EQU	FALSE		; ENABLES HEATH H8 FRONT PANEL
 ;
 BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
 CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -167,6 +167,7 @@ TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VGASIZ		.EQU	V80X25		; VGA: DISPLAY FORMAT [V80X25|V80X30|V80X43]
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
@@ -228,6 +229,18 @@ SDCNT		.EQU	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT ONLY
 SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 SDCSIOFAST	.EQU	FALSE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
 ;
+CHENABLE	.EQU	FALSE		; CH: ENABLE CH375/376 USB SUPPORT
+CHTRACE		.EQU	1		; CH: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHUSBTRACE	.EQU	1		; CHUSB: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHSDTRACE	.EQU	1		; CHSD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHCNT		.EQU	1		; CH: NUMBER OF BOARDS TO DETECT (1-2)
+CH0BASE		.EQU	$BE		; CH 0: BASE I/O ADDRESS
+CH0USBENABLE	.EQU	TRUE		; CH 0: ENABLE USB DISK
+CH0SDENABLE	.EQU	FALSE		; CH 0: ENABLE SD DISK
+CH1BASE		.EQU	$FF		; CH 1: BASE I/O ADDRESS
+CH1USBENABLE	.EQU	FALSE		; CH 1: ENABLE USB DISK
+CH1SDENABLE	.EQU	FALSE		; CH 1: ENABLE SD DISK
+;
 PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
 PRPSDENABLE	.EQU	TRUE		; PRP: ENABLE PROPIO DRIVER SD CARD SUPPORT
 PRPSDTRACE	.EQU	1		; PRP: SD CARD TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
@@ -236,6 +249,7 @@ PRPCONENABLE	.EQU	TRUE		; PRP: ENABLE PROPIO DRIVER VIDEO/KBD SUPPORT
 PPPENABLE	.EQU	FALSE		; PPP: ENABLE ZETA PARALLEL PORT PROPELLER BOARD DRIVER (PPP.ASM)
 ;
 ESPENABLE	.EQU	FALSE		; ESP: ENABLE ESP32 IO BOARD DRIVER (ESP.ASM)
+ESPCONENABLE	.EQU	TRUE		; ESP: ENABLE ESP32 CONSOLE IO DRIVER VIDEO/KBD SUPPORT
 ;
 HDSKENABLE	.EQU	FALSE		; HDSK: ENABLE SIMH HDSK DISK DRIVER (HDSK.ASM)
 HDSKTRACE	.EQU	1		; HDSK: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
--- a/Source/HBIOS/cfg_dyno.asm
+++ b/Source/HBIOS/cfg_dyno.asm
@@ -15,7 +15,7 @@
 ;
 #INCLUDE "hbios.inc"
 ;
-PLATFORM	.EQU	PLT_DYNO	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO]
+PLATFORM	.EQU	PLT_DYNO	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
 CPUFAM		.EQU	CPU_Z180	; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
@@ -34,10 +34,8 @@ DEFSERCFG	.EQU	SER_38400_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
 ;
 RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
-ROMSIZE_CHK	.EQU	0		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
 MEMMGR		.EQU	MM_Z180		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
-RAMLOC		.EQU	19		; START OF RAM AS POWER OF 2 (2^N) IN PHYSICAL ADDRESS SPACE
-RAMBIAS		.EQU	(1 << (RAMLOC - 10))	; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
+RAMBIAS		.EQU	ROMSIZE		; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
 MPGSEL_0	.EQU	$78		; Z2 MEM MGR BANK 0 PAGE SELECT REG (WRITE ONLY)
 MPGSEL_1	.EQU	$79		; Z2 MEM MGR BANK 1 PAGE SELECT REG (WRITE ONLY)
 MPGSEL_2	.EQU	$7A		; Z2 MEM MGR BANK 2 PAGE SELECT REG (WRITE ONLY)
@@ -82,7 +80,14 @@ LEDMODE		.EQU	LEDMODE_STD	; LEDMODE_[STD|RTC]
 LEDPORT		.EQU	$0E		; STATUS LED PORT ADDRESS
 LEDDISKIO	.EQU	TRUE		; ENABLES DISK I/O ACTIVITY ON STATUS LED
 ;
-DSKYENABLE	.EQU	FALSE		; ENABLES DSKY (DO NOT COMBINE WITH PPIDE)
+DSKYENABLE	.EQU	FALSE		; ENABLES DSKY FUNCTIONALITY
+DSKYDSKACT	.EQU	TRUE		; ENABLES DISK ACTIVITY ON DSKY DISPLAY
+ICMENABLE	.EQU	FALSE		; ENABLES ORIGINAL DSKY ICM DRIVER (7218)
+ICMPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF ICM PPI
+PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
+PKDPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF PKD PPI
+PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
+H8PENABLE	.EQU	FALSE		; ENABLES HEATH H8 FRONT PANEL
 ;
 BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
 CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -179,6 +184,7 @@ TMSMODE		.EQU	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MS
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
@@ -239,6 +245,8 @@ SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 SDCSIOFAST	.EQU	FALSE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
 SDMTSWAP	.EQU	FALSE		; SD: SWAP THE LOGICAL ORDER OF THE SPI PORTS OF THE MT011
 ;
+CHENABLE	.EQU	FALSE		; CH: ENABLE CH375/376 USB SUPPORT
+;
 PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
 PRPSDENABLE	.EQU	TRUE		; PRP: ENABLE PROPIO DRIVER SD CARD SUPPORT
 PRPSDTRACE	.EQU	1		; PRP: SD CARD TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
--- a/Source/HBIOS/cfg_heath.asm
+++ b/Source/HBIOS/cfg_heath.asm
@@ -0,0 +1,321 @@
+;
+;==================================================================================================
+;   ROMWBW 3.X CONFIGURATION DEFAULTS FOR RCBUS Z80
+;==================================================================================================
+;
+; THIS FILE CONTAINS THE FULL SET OF DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE. THIS FILE SHOULD *NOT* NORMALLY BE CHANGED.	INSTEAD, YOU SHOULD
+; OVERRIDE ANY SETTINGS YOU WANT USING A CONFIGURATION FILE IN THE CONFIG DIRECTORY
+; UNDER THIS DIRECTORY.
+;
+; THIS FILE CAN BE CONSIDERED A REFERENCE THAT LISTS ALL POSSIBLE CONFIGURATION SETTINGS
+; FOR THE PLATFORM.
+;
+#DEFINE PLATFORM_NAME "RCBus", " [", CONFIG, "]"
+;
+#INCLUDE "hbios.inc"
+;
+PLATFORM	.EQU	PLT_HEATH	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
+CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180|Z280]
+BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
+BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
+HBIOS_MUTEX	.EQU	FALSE		; ENABLE REENTRANT CALLS TO HBIOS (ADDS OVERHEAD)
+USELZSA2	.EQU	TRUE		; ENABLE FONT COMPRESSION
+TICKFREQ	.EQU	50		; DESIRED PERIODIC TIMER INTERRUPT FREQUENCY (HZ)
+;
+BOOT_TIMEOUT	.EQU	-1		; AUTO BOOT TIMEOUT IN SECONDS, -1 TO DISABLE, 0 FOR IMMEDIATE
+BOOT_DELAY	.EQU	0		; FIXED BOOT DELAY IN SECONDS PRIOR TO CONSOLE OUTPUT
+;
+CPUSPDCAP	.EQU	SPD_FIXED	; CPU SPEED CHANGE CAPABILITY SPD_FIXED|SPD_HILO
+CPUSPDDEF	.EQU	SPD_HIGH	; CPU SPEED DEFAULT SPD_UNSUP|SPD_HIGH|SPD_LOW
+CPUOSC		.EQU	7372800		; CPU OSC FREQ IN MHZ
+INTMODE		.EQU	1		; INTERRUPTS: 0=NONE, 1=MODE 1, 2=MODE 2, 3=MODE 3 (Z280)
+DEFSERCFG	.EQU	SER_115200_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
+;
+RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
+ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
+MEMMGR		.EQU	MM_Z2		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
+MPGSEL_0	.EQU	$78		; Z2 MEM MGR BANK 0 PAGE SELECT REG (WRITE ONLY)
+MPGSEL_1	.EQU	$79		; Z2 MEM MGR BANK 1 PAGE SELECT REG (WRITE ONLY)
+MPGSEL_2	.EQU	$7A		; Z2 MEM MGR BANK 2 PAGE SELECT REG (WRITE ONLY)
+MPGSEL_3	.EQU	$7B		; Z2 MEM MGR BANK 3 PAGE SELECT REG (WRITE ONLY)
+MPGENA		.EQU	$7C		; Z2 MEM MGR PAGING ENABLE REGISTER (BIT 0, WRITE ONLY)
+;
+RTCIO		.EQU	$C0		; RTC LATCH REGISTER ADR
+;
+KIOENABLE	.EQU	FALSE		; ENABLE ZILOG KIO SUPPORT
+KIOBASE		.EQU	$80		; KIO BASE I/O ADDRESS
+;
+CTCENABLE	.EQU	FALSE		; ENABLE ZILOG CTC SUPPORT
+CTCDEBUG	.EQU	FALSE		; ENABLE CTC DRIVER DEBUG OUTPUT
+CTCBASE		.EQU	$88		; CTC BASE I/O ADDRESS
+CTCTIMER	.EQU	FALSE		; ENABLE CTC PERIODIC TIMER
+CTCMODE		.EQU	CTCMODE_TIM16	; CTC MODE: CTCMODE_[NONE|CTR|TIM16|TIM256]
+CTCPRE		.EQU	256		; PRESCALE CONSTANT (1-256)
+CTCPRECH	.EQU	2		; PRESCALE CHANNEL (0-3)
+CTCTIMCH	.EQU	3		; TIMER CHANNEL (0-3)
+CTCOSC		.EQU	CPUOSC		; CTC CLOCK FREQUENCY
+;
+PCFENABLE	.EQU	FALSE		; ENABLE PCF8584 I2C CONTROLLER
+PCFBASE		.EQU	$F0		; PCF8584 BASE I/O ADDRESS
+;
+EIPCENABLE	.EQU	FALSE		; EIPC: ENABLE Z80 EIPC (Z84C15) INITIALIZATION
+;
+SKZENABLE	.EQU	FALSE		; ENABLE SERGEY'S Z80-512K FEATURES
+SKZDIV		.EQU	DIV_1		; UART CLK (CLK2) DIVIDER FOR Z80-512K
+;
+WDOGMODE	.EQU	WDOG_NONE	; WATCHDOG MODE: WDOG_[NONE|EZZ80|SKZ]
+WDOGIO		.EQU	$6E		; WATCHDOG REGISTER ADR
+;
+FPLED_ENABLE	.EQU	FALSE		; FP: ENABLES FRONT PANEL LEDS
+FPLED_IO	.EQU	$00		; FP: PORT ADDRESS FOR FP LEDS
+FPLED_DSKACT	.EQU	TRUE		; FP: ENABLES DISK I/O ACTIVITY ON FP LEDS
+FPSW_ENABLE	.EQU	FALSE		; FP: ENABLES FRONT PANEL SWITCHES
+FPSW_IO		.EQU	$00		; FP: PORT ADDRESS FOR FP SWITCHES
+;
+DIAGLVL		.EQU	DL_CRITICAL	; ERROR LEVEL REPORTING
+;
+LEDENABLE	.EQU	FALSE		; ENABLES STATUS LED (SINGLE LED)
+LEDMODE		.EQU	LEDMODE_STD	; LEDMODE_[STD|RTC]
+LEDPORT		.EQU	$0E		; STATUS LED PORT ADDRESS
+LEDDISKIO	.EQU	TRUE		; ENABLES DISK I/O ACTIVITY ON STATUS LED
+;
+DSKYENABLE	.EQU	FALSE		; ENABLES DSKY FUNCTIONALITY
+DSKYDSKACT	.EQU	TRUE		; ENABLES DISK ACTIVITY ON DSKY DISPLAY
+ICMENABLE	.EQU	FALSE		; ENABLES ORIGINAL DSKY ICM DRIVER (7218)
+ICMPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF ICM PPI
+PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
+PKDPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF PKD PPI
+PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
+H8PENABLE	.EQU	FALSE		; ENABLES HEATH H8 FRONT PANEL
+;
+BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
+CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
+VDAEMU		.EQU	EMUTYP_ANSI	; VDA EMULATION: EMUTYP_[TTY|ANSI]
+VDAEMU_SERKBD	.EQU	$FF		; VDA EMULATION: SERIAL KBD UNIT #, OR $FF FOR HW KBD
+ANSITRACE	.EQU	1		; ANSI DRIVER TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+PPKTRACE	.EQU	1		; PPK DRIVER TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+KBDTRACE	.EQU	1		; KBD DRIVER TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+KBDKBLOUT	.EQU	KBD_US		; KBD KEYBOARD LANGUAGE: KBD_[US|DE]
+PPKKBLOUT	.EQU	KBD_US		; PPK KEYBOARD LANGUAGE: KBD_[US|DE]
+MKYENABLE	.EQU	FALSE		; MSX 5255 PPI KEYBOARD COMPATIBLE DRIVER (REQUIRES TMS VDA DRIVER)
+MKYKBLOUT	.EQU	KBD_US		; KBD KEYBOARD LANGUAGE: KBD_[US|DE]
+;
+DSRTCENABLE	.EQU	TRUE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
+DSRTCMODE	.EQU	DSRTCMODE_STD	; DSRTC: OPERATING MODE: DSRTC_[STD|MFPIC]
+DSRTCCHG	.EQU	FALSE		; DSRTC: FORCE BATTERY CHARGE ON (USE WITH CAUTION!!!)
+;
+DS1501RTCENABLE	.EQU	FALSE		; DS1501RTC: ENABLE DS-1501 CLOCK DRIVER (DS1501RTC.ASM)
+DS1501RTC_BASE	.EQU	$50		; DS1501RTC: I/O BASE ADDRESS
+;
+BQRTCENABLE	.EQU	FALSE		; BQRTC: ENABLE BQ4845 CLOCK DRIVER (BQRTC.ASM)
+BQRTC_BASE	.EQU	$50		; BQRTC: I/O BASE ADDRESS
+;
+INTRTCENABLE	.EQU	FALSE		; ENABLE PERIODIC INTERRUPT CLOCK DRIVER (INTRTC.ASM)
+;
+RP5RTCENABLE	.EQU	FALSE		; RP5C01 RTC BASED CLOCK (RP5RTC.ASM)
+;
+HTIMENABLE	.EQU	FALSE		; ENABLE SIMH TIMER SUPPORT
+SIMRTCENABLE	.EQU	FALSE		; ENABLE SIMH CLOCK DRIVER (SIMRTC.ASM)
+;
+DS7RTCENABLE	.EQU	FALSE		; DS7RTC: ENABLE DS-1307 I2C CLOCK DRIVER (DS7RTC.ASM)
+DS7RTCMODE	.EQU	DS7RTCMODE_PCF	; DS7RTC: OPERATING MODE: DS7RTC_[PCF]
+;
+DUARTENABLE	.EQU	FALSE		; DUART: ENABLE 2681/2692 SERIAL DRIVER (DUART.ASM)
+DUARTCNT	.EQU	1		; DUART: NUMBER OF CHIPS TO DETECT (1-2)
+DUART0BASE	.EQU	$A0		; DUART 0: BASE ADDRESS OF CHIP
+DUART0ACFG	.EQU	DEFSERCFG	; DUART 0A: SERIAL LINE CONFIG
+DUART0BCFG	.EQU	DEFSERCFG	; DUART 0B: SERIAL LINE CONFIG
+DUART1BASE	.EQU	$40		; DUART 1: BASE ADDRESS OF CHIP
+DUART1ACFG	.EQU	DEFSERCFG	; DUART 1A: SERIAL LINE CONFIG
+DUART1BCFG	.EQU	DEFSERCFG	; DUART 1B: SERIAL LINE CONFIG
+;
+UARTENABLE	.EQU	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
+UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
+UARTCFG		.EQU	DEFSERCFG | SER_RTS	; UART: LINE CONFIG FOR UART PORTS
+UARTSBC		.EQU	FALSE		; UART: AUTO-DETECT SBC/ZETA/DUO ONBOARD UART
+UARTSBCFORCE	.EQU	FALSE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
+UARTCAS		.EQU	FALSE		; UART: AUTO-DETECT ECB CASSETTE UART
+UARTMFP		.EQU	FALSE		; UART: AUTO-DETECT MF/PIC UART
+UART4		.EQU	FALSE		; UART: AUTO-DETECT 4UART UART
+UARTRC		.EQU	TRUE		; UART: AUTO-DETECT RC UART
+UARTDUAL	.EQU	FALSE		; UART: AUTO-DETECT DUAL UART
+;
+ASCIENABLE	.EQU	FALSE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
+;
+Z2UENABLE	.EQU	FALSE		; Z2U: ENABLE Z280 UART SERIAL DRIVER (Z2U.ASM)
+;
+ACIAENABLE	.EQU	TRUE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
+ACIADEBUG	.EQU	FALSE		; ACIA: ENABLE DEBUG OUTPUT
+ACIACNT		.EQU	1		; ACIA: NUMBER OF CHIPS TO DETECT (1-2)
+ACIA0BASE	.EQU	$80		; ACIA 0: REGISTERS BASE ADR
+ACIA0CLK	.EQU	CPUOSC		; ACIA 0: OSC FREQ IN HZ
+ACIA0DIV	.EQU	1		; ACIA 0: SERIAL CLOCK DIVIDER
+ACIA0CFG	.EQU	DEFSERCFG	; ACIA 0: SERIAL LINE CONFIG  (SEE STD.ASM)
+ACIA1BASE	.EQU	$40		; ACIA 1: REGISTERS BASE ADR
+ACIA1CLK	.EQU	CPUOSC		; ACIA 1: OSC FREQ IN HZ
+ACIA1DIV	.EQU	1		; ACIA 1: SERIAL CLOCK DIVIDER
+ACIA1CFG	.EQU	DEFSERCFG	; ACIA 1: SERIAL LINE CONFIG  (SEE STD.ASM)
+;
+SIOENABLE	.EQU	TRUE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
+SIODEBUG	.EQU	FALSE		; SIO: ENABLE DEBUG OUTPUT
+SIOBOOT		.EQU	0		; SIO: REBOOT ON RCV CHAR (0=DISABLED)
+SIOCNT		.EQU	2		; SIO: NUMBER OF CHIPS TO DETECT (1-2), 2 CHANNELS PER CHIP
+SIO0MODE	.EQU	SIOMODE_RC	; SIO 0: CHIP TYPE: SIOMODE_[STD|RC|SMB|ZP|Z80R]
+SIO0BASE	.EQU	$80		; SIO 0: REGISTERS BASE ADR
+SIO0ACLK	.EQU	CPUOSC		; SIO 0A: OSC FREQ IN HZ, ZP=2457600/4915200, RC/SMB=7372800
+SIO0ACFG	.EQU	DEFSERCFG	; SIO 0A: SERIAL LINE CONFIG
+SIO0ACTCC	.EQU	-1		; SIO 0A: CTC CHANNEL 0=A, 1=B, 2=C, 3=D, -1 FOR NONE
+SIO0BCLK	.EQU	CPUOSC		; SIO 0B: OSC FREQ IN HZ, ZP=2457600/4915200, RC/SMB=7372800
+SIO0BCFG	.EQU	DEFSERCFG	; SIO 0B: SERIAL LINE CONFIG
+SIO0BCTCC	.EQU	-1		; SIO 0B: CTC CHANNEL 0=A, 1=B, 2=C, 3=D, -1 FOR NONE
+SIO1MODE	.EQU	SIOMODE_RC	; SIO 1: CHIP TYPE: SIOMODE_[STD|RC|SMB|ZP|Z80R]
+SIO1BASE	.EQU	$84		; SIO 1: REGISTERS BASE ADR
+SIO1ACLK	.EQU	CPUOSC		; SIO 1A: OSC FREQ IN HZ, ZP=2457600/4915200, RC/SMB=7372800
+SIO1ACFG	.EQU	DEFSERCFG	; SIO 1A: SERIAL LINE CONFIG
+SIO1ACTCC	.EQU	-1		; SIO 1A: CTC CHANNEL 0=A, 1=B, 2=C, 3=D, -1 FOR NONE
+SIO1BCLK	.EQU	CPUOSC		; SIO 1B: OSC FREQ IN HZ, ZP=2457600/4915200, RC/SMB=7372800
+SIO1BCFG	.EQU	DEFSERCFG	; SIO 1B: SERIAL LINE CONFIG
+SIO1BCTCC	.EQU	-1		; SIO 1B: CTC CHANNEL 0=A, 1=B, 2=C, 3=D, -1 FOR NONE
+;
+XIOCFG		.EQU	DEFSERCFG	; XIO: SERIAL LINE CONFIG
+;
+VDUENABLE	.EQU	FALSE		; VDU: ENABLE VDU VIDEO/KBD DRIVER (VDU.ASM)
+CVDUENABLE	.EQU	FALSE		; CVDU: ENABLE CVDU VIDEO/KBD DRIVER (CVDU.ASM)
+GDCENABLE	.EQU	FALSE		; GDC: ENABLE 7220 GDC VIDEO/KBD DRIVER (GDC.ASM)
+TMSENABLE	.EQU	FALSE		; TMS: ENABLE TMS9918 VIDEO/KBD DRIVER (TMS.ASM)
+TMSMODE		.EQU	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MSXKBD|COLECO]
+TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
+VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
+VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
+;
+MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
+MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
+MDRAM		.EQU	TRUE		; MD: ENABLE RAM DISK
+MDTRACE		.EQU	1		; MD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+MDFFENABLE	.EQU	FALSE		; MD: ENABLE FLASH FILE SYSTEM
+;
+FDENABLE	.EQU	FALSE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
+FDMODE		.EQU	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC|MBC]
+FDCNT		.EQU	2		; FD: NUMBER OF FLOPPY DRIVES ON THE INTERFACE (1-2)
+FDTRACE		.EQU	1		; FD: TRACE LEVEL (0=NO,1=FATAL,2=ERRORS,3=ALL)
+FDMAUTO		.EQU	TRUE		; FD: AUTO SELECT DEFAULT/ALTERNATE MEDIA FORMATS
+FD0TYPE		.EQU	FDT_3HD		; FD 0: DRIVE TYPE: FDT_[3DD|3HD|5DD|5HD|8]
+FD1TYPE		.EQU	FDT_3HD		; FD 1: DRIVE TYPE: FDT_[3DD|3HD|5DD|5HD|8]
+;
+RFENABLE	.EQU	FALSE		; RF: ENABLE RAM FLOPPY DRIVER
+;
+IDEENABLE	.EQU	FALSE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
+IDETRACE	.EQU	1		; IDE: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+IDECNT		.EQU	1		; IDE: NUMBER OF IDE INTERFACES TO DETECT (1-3), 2 DRIVES EACH
+IDE0MODE	.EQU	IDEMODE_RC	; IDE 0: DRIVER MODE: IDEMODE_[DIO|DIDE|MK4|RC]
+IDE0BASE	.EQU	$10		; IDE 0: IO BASE ADDRESS
+IDE0DATLO	.EQU	$00		; IDE 0: DATA LO PORT FOR 16-BIT I/O
+IDE0DATHI	.EQU	$00		; IDE 0: DATA HI PORT FOR 16-BIT I/O
+IDE0A8BIT	.EQU	TRUE		; IDE 0A (MASTER): 8 BIT XFER
+IDE0B8BIT	.EQU	TRUE		; IDE 0B (MASTER): 8 BIT XFER
+IDE1MODE	.EQU	IDEMODE_NONE	; IDE 1: DRIVER MODE: IDEMODE_[DIO|DIDE|MK4|RC]
+IDE1BASE	.EQU	$00		; IDE 1: IO BASE ADDRESS
+IDE1DATLO	.EQU	$00		; IDE 1: DATA LO PORT FOR 16-BIT I/O
+IDE1DATHI	.EQU	$00		; IDE 1: DATA HI PORT FOR 16-BIT I/O
+IDE1A8BIT	.EQU	TRUE		; IDE 1A (MASTER): 8 BIT XFER
+IDE1B8BIT	.EQU	TRUE		; IDE 1B (MASTER): 8 BIT XFER
+IDE2MODE	.EQU	IDEMODE_NONE	; IDE 2: DRIVER MODE: IDEMODE_[DIO|DIDE|MK4|RC]
+IDE2BASE	.EQU	$00		; IDE 2: IO BASE ADDRESS
+IDE2DATLO	.EQU	$00		; IDE 2: DATA LO PORT FOR 16-BIT I/O
+IDE2DATHI	.EQU	$00		; IDE 2: DATA HI PORT FOR 16-BIT I/O
+IDE2A8BIT	.EQU	TRUE		; IDE 2A (MASTER): 8 BIT XFER
+IDE2B8BIT	.EQU	TRUE		; IDE 2B (MASTER): 8 BIT XFER
+;
+PPIDEENABLE	.EQU	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
+PPIDETRACE	.EQU	1		; PPIDE: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+PPIDECNT	.EQU	1		; PPIDE: NUMBER OF PPI CHIPS TO DETECT (1-3), 2 DRIVES PER CHIP
+PPIDE0BASE	.EQU	$20		; PPIDE 0: PPI REGISTERS BASE ADR
+PPIDE0A8BIT	.EQU	FALSE		; PPIDE 0A (MASTER): 8 BIT XFER
+PPIDE0B8BIT	.EQU	FALSE		; PPIDE 0B (SLAVE): 8 BIT XFER
+PPIDE1BASE	.EQU	$00		; PPIDE 1: PPI REGISTERS BASE ADR
+PPIDE1A8BIT	.EQU	FALSE		; PPIDE 1A (MASTER): 8 BIT XFER
+PPIDE1B8BIT	.EQU	FALSE		; PPIDE 0B (SLAVE): 8 BIT XFER
+PPIDE2BASE	.EQU	$00		; PPIDE 2: PPI REGISTERS BASE ADR
+PPIDE2A8BIT	.EQU	FALSE		; PPIDE 2A (MASTER): 8 BIT XFER
+PPIDE2B8BIT	.EQU	FALSE		; PPIDE 0B (SLAVE): 8 BIT XFER
+;
+SDENABLE	.EQU	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
+SDMODE		.EQU	SDMODE_MT	; SD: DRIVER MODE: SDMODE_[JUHA|N8|CSIO|PPI|UART|DSD|MK4|SC|MT|PIO|Z80R|USR]
+SDPPIBASE	.EQU	$60		; SD: BASE I/O ADDRESS OF PPI FOR PPI MODDE
+SDCNT		.EQU	2		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT ONLY
+SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+SDCSIOFAST	.EQU	FALSE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
+SDMTSWAP	.EQU	FALSE		; SD: SWAP THE LOGICAL ORDER OF THE SPI PORTS OF THE MT011
+;
+CHENABLE	.EQU	FALSE		; CH: ENABLE CH375/376 USB SUPPORT
+;
+PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
+PRPSDENABLE	.EQU	TRUE		; PRP: ENABLE PROPIO DRIVER SD CARD SUPPORT
+PRPSDTRACE	.EQU	1		; PRP: SD CARD TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+PRPCONENABLE	.EQU	TRUE		; PRP: ENABLE PROPIO DRIVER VIDEO/KBD SUPPORT
+;
+PPPENABLE	.EQU	FALSE		; PPP: ENABLE ZETA PARALLEL PORT PROPELLER BOARD DRIVER (PPP.ASM)
+;
+ESPENABLE	.EQU	FALSE		; ESP: ENABLE ESP32 IO BOARD DRIVER (ESP.ASM)
+;
+HDSKENABLE	.EQU	FALSE		; HDSK: ENABLE SIMH HDSK DISK DRIVER (HDSK.ASM)
+;
+PIOENABLE	.EQU	FALSE		; PIO: ENABLE ZILOG PIO DRIVER (PIO.ASM)
+PIOCNT		.EQU	2		; PIO: NUMBER OF CHIPS TO DETECT (1-2), 2 CHANNELS PER CHIP
+PIO0BASE	.EQU	$B8		; PIO 0: REGISTERS BASE ADR
+PIO1BASE	.EQU	$BC		; PIO 1: REGISTERS BASE ADR
+;
+LPTENABLE	.EQU	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
+LPTMODE		.EQU	LPTMODE_MG014	; LPT: DRIVER MODE: LPTMODE_[NONE|SPP|MG014]
+LPTCNT		.EQU	1		; LPT: NUMBER OF CHIPS TO DETECT (1-2)
+LPTTRACE	.EQU	1		; LPT: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+LPT0BASE	.EQU	$0C		; LPT 0: REGISTERS BASE ADR
+LPT1BASE	.EQU	$00		; LPT 1: REGISTERS BASE ADR
+;
+PPAENABLE	.EQU	FALSE		; PPA: ENABLE PPA DISK DRIVER (PPA.ASM)
+PPACNT		.EQU	1		; PPA: NUMBER OF PPA DEVICES (1-2)
+PPATRACE	.EQU	1		; PPA: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+PPAMODE		.EQU	PPAMODE_MG014	; PPA: DRIVER MODE: PPAMODE_[NONE|SPP|MG014]
+PPA0BASE	.EQU	LPT0BASE	; PPA 0: BASE I/O ADDRESS OF PPI FOR PPA
+PPA1BASE	.EQU	LPT1BASE	; PPA 1: BASE I/O ADDRESS OF PPI FOR PPA
+;
+IMMENABLE	.EQU	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
+IMMCNT		.EQU	1		; IMM: NUMBER OF IMM DEVICES (1-2)
+IMMTRACE	.EQU	1		; IMM: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+IMMMODE		.EQU	IMMMODE_MG014	; IMM: DRIVER MODE: IMMMODE_[NONE|SPP|MG014]
+IMM0BASE	.EQU	LPT0BASE	; IMM 0: BASE I/O ADDRESS OF PPI FOR IMM
+IMM1BASE	.EQU	LPT1BASE	; IMM 1: BASE I/O ADDRESS OF PPI FOR IMM
+;
+SYQENABLE	.EQU	FALSE		; SYQ: ENABLE IMM DISK DRIVER (SYQ.ASM)
+SYQCNT		.EQU	1		; SYQ: NUMBER OF SYQ DEVICES (1-2)
+SYQTRACE	.EQU	1		; SYQ: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+SYQMODE		.EQU	IMMMODE_MG014	; SYQ: DRIVER MODE: SYQMODE_[NONE|SPP|MG014]
+SYQ0BASE	.EQU	LPT0BASE	; SYQ 0: BASE I/O ADDRESS OF PPI FOR SYQ
+SYQ1BASE	.EQU	LPT1BASE	; SYQ 1: BASE I/O ADDRESS OF PPI FOR SYQ
+;
+PIO_4P		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB 4P BOARD
+PIO_ZP		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR ECB ZILOG PERIPHERALS BOARD (PIO.ASM)
+PIO_SBC		.EQU	FALSE		; PIO: ENABLE PARALLEL PORT DRIVER FOR 8255 CHIP
+;
+UFENABLE	.EQU	FALSE		; UF: ENABLE ECB USB FIFO DRIVER (UF.ASM)
+;
+SN76489ENABLE	.EQU	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
+AUDIOTRACE	.EQU	FALSE		; ENABLE TRACING TO CONSOLE OF SOUND DRIVER
+SN7CLK		.EQU	3579545		; SN: PSG CLOCK FREQ, ASSUME MSX STD
+SNMODE		.EQU	SNMODE_RC	; SN: DRIVER MODE: SNMODE_[NONE|RC|VGM]
+;
+AY38910ENABLE	.EQU	FALSE		; AY: ENABLE AY-3-8910 / YM2149 SOUND DRIVER
+AY_CLK		.EQU	1789772		; AY: PSG CLOCK FREQ, ASSUME MSX STD
+AYMODE		.EQU	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LINC|MBC]
+;
+SPKENABLE	.EQU	FALSE		; SPK: ENABLE RTC LATCH IOBIT SOUND DRIVER (SPK.ASM)
+;
+DMAENABLE	.EQU	FALSE		; DMA: ENABLE DMA DRIVER (DMA.ASM)
+DMABASE		.EQU	$E0		; DMA: DMA BASE ADDRESS
+DMAMODE		.EQU	DMAMODE_RC	; DMA: DMA MODE (NONE|ECB|Z180|Z280|RC|MBC|DUO)
+;
+YM2612ENABLE	.EQU	FALSE		; YM2612: ENABLE YM2612 DRIVER
+VGMBASE		.EQU	$C0		; YM2612: BASE ADDRESS FOR VGM BOARD (YM2612/SN76489s/CTC)
--- a/Source/HBIOS/cfg_master.asm
+++ b/Source/HBIOS/cfg_master.asm
@@ -12,7 +12,7 @@
 ;
 #INCLUDE "hbios.inc"
 ;
-PLATFORM	.EQU	PLT_SBC		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO]
+PLATFORM	.EQU	PLT_SBC		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
 CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
@@ -31,10 +31,8 @@ DEFSERCFG	.EQU	SER_38400_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
 ;
 RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
-ROMSIZE_CHK	.EQU	0		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
 MEMMGR		.EQU	MM_NONE		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
-RAMLOC		.EQU	19		; START OF RAM AS POWER OF 2 (2^N) IN PHYSICAL ADDRESS SPACE
-RAMBIAS		.EQU	(1 << (RAMLOC - 10))	; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
+RAMBIAS		.EQU	ROMSIZE		; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
 MPCL_RAM	.EQU	$78		; SBC MEM MGR RAM PAGE SELECT REG (WRITE ONLY)
 MPCL_ROM	.EQU	$7C		; SBC MEM MGR ROM PAGE SELECT REG (WRITE ONLY)
 MPGSEL_0	.EQU	$78		; Z2 MEM MGR BANK 0 PAGE SELECT REG (WRITE ONLY)
@@ -118,6 +116,7 @@ ICMPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF ICM PPI
 PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
 PKDPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF PKD PPI
 PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
+H8PENABLE	.EQU	FALSE		; ENABLES HEATH H8 FRONT PANEL
 ;
 BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
 CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -236,6 +235,7 @@ TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VGASIZ		.EQU	V80X25		; VGA: DISPLAY FORMAT [V80X25|V80X30|V80X43]
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
@@ -297,6 +297,18 @@ SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 SDCSIOFAST	.EQU	FALSE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
 SDMTSWAP	.EQU	FALSE		; SD: SWAP THE LOGICAL ORDER OF THE SPI PORTS OF THE MT011
 ;
+CHENABLE	.EQU	FALSE		; CH: ENABLE CH375/376 USB SUPPORT
+CHTRACE		.EQU	1		; CH: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHUSBTRACE	.EQU	1		; CHUSB: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHSDTRACE	.EQU	1		; CHSD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHCNT		.EQU	1		; CH: NUMBER OF BOARDS TO DETECT (1-2)
+CH0BASE		.EQU	$BE		; CH 0: BASE I/O ADDRESS
+CH0USBENABLE	.EQU	TRUE		; CH 0: ENABLE USB DISK
+CH0SDENABLE	.EQU	FALSE		; CH 0: ENABLE SD DISK
+CH1BASE		.EQU	$FF		; CH 1: BASE I/O ADDRESS
+CH1USBENABLE	.EQU	FALSE		; CH 1: ENABLE USB DISK
+CH1SDENABLE	.EQU	FALSE		; CH 1: ENABLE SD DISK
+;
 PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
 PRPSDENABLE	.EQU	TRUE		; PRP: ENABLE PROPIO DRIVER SD CARD SUPPORT
 PRPSDTRACE	.EQU	1		; PRP: SD CARD TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
--- a/Source/HBIOS/cfg_mbc.asm
+++ b/Source/HBIOS/cfg_mbc.asm
@@ -15,7 +15,7 @@
 ;
 #INCLUDE "hbios.inc"
 ;
-PLATFORM	.EQU	PLT_MBC		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO]
+PLATFORM	.EQU	PLT_MBC		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
 CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
@@ -34,7 +34,6 @@ DEFSERCFG	.EQU	SER_38400_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
 ;
 RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
-ROMSIZE_CHK	.EQU	0		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
 MEMMGR		.EQU	MM_MBC		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
 MPCL_RAM	.EQU	$78		; SBC MEM MGR RAM PAGE SELECT REG (WRITE ONLY)
 MPCL_ROM	.EQU	$7C		; SBC MEM MGR ROM PAGE SELECT REG (WRITE ONLY)
@@ -83,6 +82,7 @@ ICMPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF ICM PPI
 PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
 PKDPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF PKD PPI
 PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
+H8PENABLE	.EQU	FALSE		; ENABLES HEATH H8 FRONT PANEL
 ;
 BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
 CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -164,6 +164,7 @@ TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VGASIZ		.EQU	V80X25		; VGA: DISPLAY FORMAT [V80X25|V80X30|V80X43]
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
@@ -225,6 +226,8 @@ SDCNT		.EQU	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT ONLY
 SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 SDCSIOFAST	.EQU	FALSE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
 ;
+CHENABLE	.EQU	FALSE		; CH: ENABLE CH375/376 USB SUPPORT
+;
 PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
 PRPSDENABLE	.EQU	TRUE		; PRP: ENABLE PROPIO DRIVER SD CARD SUPPORT
 PRPSDTRACE	.EQU	1		; PRP: SD CARD TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
--- a/Source/HBIOS/cfg_mk4.asm
+++ b/Source/HBIOS/cfg_mk4.asm
@@ -15,7 +15,7 @@
 ;
 #INCLUDE "hbios.inc"
 ;
-PLATFORM	.EQU	PLT_MK4		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO]
+PLATFORM	.EQU	PLT_MK4		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
 CPUFAM		.EQU	CPU_Z180	; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
@@ -34,10 +34,8 @@ DEFSERCFG	.EQU	SER_38400_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
 ;
 RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
-ROMSIZE_CHK	.EQU	0		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
 MEMMGR		.EQU	MM_Z180		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
-RAMLOC		.EQU	19		; START OF RAM AS POWER OF 2 (2^N) IN PHYSICAL ADDRESS SPACE
-RAMBIAS		.EQU	(1 << (RAMLOC - 10))	; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
+RAMBIAS		.EQU	ROMSIZE		; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
 ;
 Z180_BASE	.EQU	$40		; Z180: I/O BASE ADDRESS FOR INTERNAL REGISTERS
 Z180_CLKDIV	.EQU	1		; Z180: CHK DIV: 0=OSC/2, 1=OSC, 2=OSC*2
@@ -89,6 +87,7 @@ ICMPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF ICM PPI
 PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
 PKDPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF PKD PPI
 PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
+H8PENABLE	.EQU	FALSE		; ENABLES HEATH H8 FRONT PANEL
 ;
 BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
 CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -175,6 +174,7 @@ TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VGASIZ		.EQU	V80X25		; VGA: DISPLAY FORMAT [V80X25|V80X30|V80X43]
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
@@ -235,6 +235,8 @@ SDCNT		.EQU	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT ONLY
 SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 SDCSIOFAST	.EQU	TRUE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
 ;
+CHENABLE	.EQU	FALSE		; CH: ENABLE CH375/376 USB SUPPORT
+;
 PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
 PRPSDENABLE	.EQU	TRUE		; PRP: ENABLE PROPIO DRIVER SD CARD SUPPORT
 PRPSDTRACE	.EQU	1		; PRP: SD CARD TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
--- a/Source/HBIOS/cfg_n8.asm
+++ b/Source/HBIOS/cfg_n8.asm
@@ -15,7 +15,7 @@
 ;
 #INCLUDE "hbios.inc"
 ;
-PLATFORM	.EQU	PLT_N8		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO]
+PLATFORM	.EQU	PLT_N8		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
 CPUFAM		.EQU	CPU_Z180	; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
@@ -34,10 +34,8 @@ DEFSERCFG	.EQU	SER_38400_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
 ;
 RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
-ROMSIZE_CHK	.EQU	0		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
 MEMMGR		.EQU	MM_N8		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
 RAMBIAS		.EQU	0		; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
-RAMLOC		.EQU	0		; START OF RAM AS POWER OF 2 (2^N) IN PHYSICAL ADDRESS SPACE
 ;
 Z180_BASE	.EQU	$40		; Z180: I/O BASE ADDRESS FOR INTERNAL REGISTERS
 Z180_CLKDIV	.EQU	1		; Z180: CHK DIV: 0=OSC/2, 1=OSC, 2=OSC*2
@@ -91,6 +89,7 @@ ICMPPIBASE	.EQU	N8_PPI0		; BASE I/O ADDRESS OF ICM PPI
 PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
 PKDPPIBASE	.EQU	N8_PPI0		; BASE I/O ADDRESS OF PKD PPI
 PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
+H8PENABLE	.EQU	FALSE		; ENABLES HEATH H8 FRONT PANEL
 ;
 BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
 CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -177,6 +176,7 @@ TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VGASIZ		.EQU	V80X25		; VGA: DISPLAY FORMAT [V80X25|V80X30|V80X43]
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
@@ -237,6 +237,8 @@ SDCNT		.EQU	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT ONLY
 SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 SDCSIOFAST	.EQU	FALSE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
 ;
+CHENABLE	.EQU	FALSE		; CH: ENABLE CH375/376 USB SUPPORT
+;
 PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
 PRPSDENABLE	.EQU	TRUE		; PRP: ENABLE PROPIO DRIVER SD CARD SUPPORT
 PRPSDTRACE	.EQU	1		; PRP: SD CARD TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
--- a/Source/HBIOS/cfg_rcz180.asm
+++ b/Source/HBIOS/cfg_rcz180.asm
@@ -15,7 +15,7 @@
 ;
 #INCLUDE "hbios.inc"
 ;
-PLATFORM	.EQU	PLT_RCZ180	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO]
+PLATFORM	.EQU	PLT_RCZ180	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
 CPUFAM		.EQU	CPU_Z180	; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
@@ -34,10 +34,8 @@ DEFSERCFG	.EQU	SER_115200_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
 ;
 RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
-ROMSIZE_CHK	.EQU	0		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
 MEMMGR		.EQU	MM_Z180		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
-RAMLOC		.EQU	19		; START OF RAM AS POWER OF 2 (2^N) IN PHYSICAL ADDRESS SPACE
-RAMBIAS		.EQU	(1 << (RAMLOC - 10))	; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
+RAMBIAS		.EQU	ROMSIZE		; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
 MPGSEL_0	.EQU	$78		; Z2 MEM MGR BANK 0 PAGE SELECT REG (WRITE ONLY)
 MPGSEL_1	.EQU	$79		; Z2 MEM MGR BANK 1 PAGE SELECT REG (WRITE ONLY)
 MPGSEL_2	.EQU	$7A		; Z2 MEM MGR BANK 2 PAGE SELECT REG (WRITE ONLY)
@@ -88,7 +86,14 @@ LEDMODE		.EQU	LEDMODE_STD	; LEDMODE_[STD|RTC]
 LEDPORT		.EQU	$0E		; STATUS LED PORT ADDRESS
 LEDDISKIO	.EQU	TRUE		; ENABLES DISK I/O ACTIVITY ON STATUS LED
 ;
-DSKYENABLE	.EQU	FALSE		; ENABLES DSKY (DO NOT COMBINE WITH PPIDE)
+DSKYENABLE	.EQU	FALSE		; ENABLES DSKY FUNCTIONALITY
+DSKYDSKACT	.EQU	TRUE		; ENABLES DISK ACTIVITY ON DSKY DISPLAY
+ICMENABLE	.EQU	FALSE		; ENABLES ORIGINAL DSKY ICM DRIVER (7218)
+ICMPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF ICM PPI
+PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
+PKDPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF PKD PPI
+PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
+H8PENABLE	.EQU	FALSE		; ENABLES HEATH H8 FRONT PANEL
 ;
 BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
 CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -185,6 +190,7 @@ TMSMODE		.EQU	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MS
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
@@ -245,6 +251,18 @@ SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 SDCSIOFAST	.EQU	FALSE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
 SDMTSWAP	.EQU	FALSE		; SD: SWAP THE LOGICAL ORDER OF THE SPI PORTS OF THE MT011
 ;
+CHENABLE	.EQU	FALSE		; CH: ENABLE CH375/376 USB SUPPORT
+CHTRACE		.EQU	1		; CH: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHUSBTRACE	.EQU	1		; CHUSB: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHSDTRACE	.EQU	1		; CHSD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHCNT		.EQU	1		; CH: NUMBER OF BOARDS TO DETECT (1-2)
+CH0BASE		.EQU	$BE		; CH 0: BASE I/O ADDRESS
+CH0USBENABLE	.EQU	TRUE		; CH 0: ENABLE USB DISK
+CH0SDENABLE	.EQU	FALSE		; CH 0: ENABLE SD DISK
+CH1BASE		.EQU	$FF		; CH 1: BASE I/O ADDRESS
+CH1USBENABLE	.EQU	FALSE		; CH 1: ENABLE USB DISK
+CH1SDENABLE	.EQU	FALSE		; CH 1: ENABLE SD DISK
+;
 PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
 PRPSDENABLE	.EQU	TRUE		; PRP: ENABLE PROPIO DRIVER SD CARD SUPPORT
 PRPSDTRACE	.EQU	1		; PRP: SD CARD TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
--- a/Source/HBIOS/cfg_rcz280.asm
+++ b/Source/HBIOS/cfg_rcz280.asm
@@ -15,7 +15,7 @@
 ;
 #INCLUDE "hbios.inc"
 ;
-PLATFORM	.EQU	PLT_RCZ280	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO]
+PLATFORM	.EQU	PLT_RCZ280	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
 CPUFAM		.EQU	CPU_Z280	; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
@@ -34,10 +34,8 @@ DEFSERCFG	.EQU	SER_115200_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
 ;
 RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
-ROMSIZE_CHK	.EQU	0		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
 MEMMGR		.EQU	MM_Z2		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
-RAMLOC		.EQU	19		; START OF RAM AS POWER OF 2 (2^N) IN PHYSICAL ADDRESS SPACE
-RAMBIAS		.EQU	(1 << (RAMLOC - 10))	; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
+RAMBIAS		.EQU	ROMSIZE		; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
 MPGSEL_0	.EQU	$78		; Z2 MEM MGR BANK 0 PAGE SELECT REG (WRITE ONLY)
 MPGSEL_1	.EQU	$79		; Z2 MEM MGR BANK 1 PAGE SELECT REG (WRITE ONLY)
 MPGSEL_2	.EQU	$7A		; Z2 MEM MGR BANK 2 PAGE SELECT REG (WRITE ONLY)
@@ -82,7 +80,14 @@ LEDMODE		.EQU	LEDMODE_STD	; LEDMODE_[STD|RTC]
 LEDPORT		.EQU	$0E		; STATUS LED PORT ADDRESS
 LEDDISKIO	.EQU	TRUE		; ENABLES DISK I/O ACTIVITY ON STATUS LED
 ;
-DSKYENABLE	.EQU	FALSE		; ENABLES DSKY (DO NOT COMBINE WITH PPIDE)
+DSKYENABLE	.EQU	FALSE		; ENABLES DSKY FUNCTIONALITY
+DSKYDSKACT	.EQU	TRUE		; ENABLES DISK ACTIVITY ON DSKY DISPLAY
+ICMENABLE	.EQU	FALSE		; ENABLES ORIGINAL DSKY ICM DRIVER (7218)
+ICMPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF ICM PPI
+PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
+PKDPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF PKD PPI
+PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
+H8PENABLE	.EQU	FALSE		; ENABLES HEATH H8 FRONT PANEL
 ;
 BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
 CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -189,6 +194,7 @@ TMSMODE		.EQU	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MS
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
@@ -249,6 +255,18 @@ SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 SDCSIOFAST	.EQU	FALSE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
 SDMTSWAP	.EQU	FALSE		; SD: SWAP THE LOGICAL ORDER OF THE SPI PORTS OF THE MT011
 ;
+CHENABLE	.EQU	FALSE		; CH: ENABLE CH375/376 USB SUPPORT
+CHTRACE		.EQU	1		; CH: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHUSBTRACE	.EQU	1		; CHUSB: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHSDTRACE	.EQU	1		; CHSD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHCNT		.EQU	1		; CH: NUMBER OF BOARDS TO DETECT (1-2)
+CH0BASE		.EQU	$BE		; CH 0: BASE I/O ADDRESS
+CH0USBENABLE	.EQU	TRUE		; CH 0: ENABLE USB DISK
+CH0SDENABLE	.EQU	FALSE		; CH 0: ENABLE SD DISK
+CH1BASE		.EQU	$FF		; CH 1: BASE I/O ADDRESS
+CH1USBENABLE	.EQU	FALSE		; CH 1: ENABLE USB DISK
+CH1SDENABLE	.EQU	FALSE		; CH 1: ENABLE SD DISK
+;
 PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
 PRPSDENABLE	.EQU	TRUE		; PRP: ENABLE PROPIO DRIVER SD CARD SUPPORT
 PRPSDTRACE	.EQU	1		; PRP: SD CARD TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
--- a/Source/HBIOS/cfg_rcz80.asm
+++ b/Source/HBIOS/cfg_rcz80.asm
@@ -15,7 +15,7 @@
 ;
 #INCLUDE "hbios.inc"
 ;
-PLATFORM	.EQU	PLT_RCZ80	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO]
+PLATFORM	.EQU	PLT_RCZ80	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
 CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
@@ -34,7 +34,6 @@ DEFSERCFG	.EQU	SER_115200_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
 ;
 RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
-ROMSIZE_CHK	.EQU	0		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
 MEMMGR		.EQU	MM_Z2		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
 MPGSEL_0	.EQU	$78		; Z2 MEM MGR BANK 0 PAGE SELECT REG (WRITE ONLY)
 MPGSEL_1	.EQU	$79		; Z2 MEM MGR BANK 1 PAGE SELECT REG (WRITE ONLY)
@@ -81,7 +80,14 @@ LEDMODE		.EQU	LEDMODE_STD	; LEDMODE_[STD|RTC]
 LEDPORT		.EQU	$0E		; STATUS LED PORT ADDRESS
 LEDDISKIO	.EQU	TRUE		; ENABLES DISK I/O ACTIVITY ON STATUS LED
 ;
-DSKYENABLE	.EQU	FALSE		; ENABLES DSKY (DO NOT COMBINE WITH PPIDE)
+DSKYENABLE	.EQU	FALSE		; ENABLES DSKY FUNCTIONALITY
+DSKYDSKACT	.EQU	TRUE		; ENABLES DISK ACTIVITY ON DSKY DISPLAY
+ICMENABLE	.EQU	FALSE		; ENABLES ORIGINAL DSKY ICM DRIVER (7218)
+ICMPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF ICM PPI
+PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
+PKDPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF PKD PPI
+PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
+H8PENABLE	.EQU	FALSE		; ENABLES HEATH H8 FRONT PANEL
 ;
 BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
 CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -183,6 +189,7 @@ TMSMODE		.EQU	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MS
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
@@ -243,6 +250,18 @@ SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 SDCSIOFAST	.EQU	FALSE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
 SDMTSWAP	.EQU	FALSE		; SD: SWAP THE LOGICAL ORDER OF THE SPI PORTS OF THE MT011
 ;
+CHENABLE	.EQU	FALSE		; CH: ENABLE CH375/376 USB SUPPORT
+CHTRACE		.EQU	1		; CH: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHUSBTRACE	.EQU	1		; CHUSB: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHSDTRACE	.EQU	1		; CHSD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHCNT		.EQU	1		; CH: NUMBER OF BOARDS TO DETECT (1-2)
+CH0BASE		.EQU	$BE		; CH 0: BASE I/O ADDRESS
+CH0USBENABLE	.EQU	TRUE		; CH 0: ENABLE USB DISK
+CH0SDENABLE	.EQU	FALSE		; CH 0: ENABLE SD DISK
+CH1BASE		.EQU	$FF		; CH 1: BASE I/O ADDRESS
+CH1USBENABLE	.EQU	FALSE		; CH 1: ENABLE USB DISK
+CH1SDENABLE	.EQU	FALSE		; CH 1: ENABLE SD DISK
+;
 PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
 PRPSDENABLE	.EQU	TRUE		; PRP: ENABLE PROPIO DRIVER SD CARD SUPPORT
 PRPSDTRACE	.EQU	1		; PRP: SD CARD TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
--- a/Source/HBIOS/cfg_rph.asm
+++ b/Source/HBIOS/cfg_rph.asm
@@ -15,7 +15,7 @@
 ;
 #INCLUDE "hbios.inc"
 ;
-PLATFORM	.EQU	PLT_RPH		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO]
+PLATFORM	.EQU	PLT_RPH		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
 CPUFAM		.EQU	CPU_Z180	; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	TRUE		; ENABLE LOW BATTERY WARNING MESSAGE
@@ -34,10 +34,8 @@ DEFSERCFG	.EQU	SER_38400_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
 ;
 RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
-ROMSIZE_CHK	.EQU	0		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
 MEMMGR		.EQU	MM_RPH		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
 RAMBIAS		.EQU	0		; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
-RAMLOC		.EQU	0		; START OF RAM AS POWER OF 2 (2^N) IN PHYSICAL ADDRESS SPACE
 ;
 Z180_BASE	.EQU	$40		; Z180: I/O BASE ADDRESS FOR INTERNAL REGISTERS
 Z180_CLKDIV	.EQU	1		; Z180: CHK DIV: 0=OSC/2, 1=OSC, 2=OSC*2
@@ -89,6 +87,7 @@ ICMPPIBASE	.EQU	RPH_PPI0	; BASE I/O ADDRESS OF ICM PPI
 PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
 PKDPPIBASE	.EQU	RPH_PPI0	; BASE I/O ADDRESS OF PKD PPI
 PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
+H8PENABLE	.EQU	FALSE		; ENABLES HEATH H8 FRONT PANEL
 ;
 BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
 CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -166,6 +165,7 @@ TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VGASIZ		.EQU	V80X25		; VGA: DISPLAY FORMAT [V80X25|V80X30|V80X43]
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
@@ -226,6 +226,8 @@ SDCNT		.EQU	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT ONLY
 SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 SDCSIOFAST	.EQU	FALSE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
 ;
+CHENABLE	.EQU	FALSE		; CH: ENABLE CH375/376 USB SUPPORT
+;
 PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
 PRPSDENABLE	.EQU	FALSE		; PRP: ENABLE PROPIO DRIVER SD CARD SUPPORT
 PRPSDTRACE	.EQU	1		; PRP: SD CARD TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
--- a/Source/HBIOS/cfg_s100.asm
+++ b/Source/HBIOS/cfg_s100.asm
@@ -15,7 +15,7 @@
 ;
 #INCLUDE "hbios.inc"
 ;
-PLATFORM	.EQU	PLT_S100	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO]
+PLATFORM	.EQU	PLT_S100	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
 CPUFAM		.EQU	CPU_Z180	; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
@@ -34,10 +34,8 @@ DEFSERCFG	.EQU	SER_57600_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
 ;
 RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
-ROMSIZE_CHK	.EQU	0		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
 MEMMGR		.EQU	MM_Z180		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
-RAMLOC		.EQU	19		; START OF RAM AS POWER OF 2 (2^N) IN PHYSICAL ADDRESS SPACE
-RAMBIAS		.EQU	(1 << (RAMLOC - 10))	; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
+RAMBIAS		.EQU	ROMSIZE		; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
 MPGSEL_0	.EQU	$78		; Z2 MEM MGR BANK 0 PAGE SELECT REG (WRITE ONLY)
 MPGSEL_1	.EQU	$79		; Z2 MEM MGR BANK 1 PAGE SELECT REG (WRITE ONLY)
 MPGSEL_2	.EQU	$7A		; Z2 MEM MGR BANK 2 PAGE SELECT REG (WRITE ONLY)
@@ -46,8 +44,8 @@ MPGENA		.EQU	$7C		; Z2 MEM MGR PAGING ENABLE REGISTER (BIT 0, WRITE ONLY)
 ;
 Z180_BASE	.EQU	$C0		; Z180: I/O BASE ADDRESS FOR INTERNAL REGISTERS
 Z180_CLKDIV	.EQU	1		; Z180: CHK DIV: 0=OSC/2, 1=OSC, 2=OSC*2
-Z180_MEMWAIT	.EQU	0		; Z180: MEMORY WAIT STATES (0-3)
-Z180_IOWAIT	.EQU	1		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
+Z180_MEMWAIT	.EQU	1		; Z180: MEMORY WAIT STATES (0-3)
+Z180_IOWAIT	.EQU	2		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
 Z180_TIMER	.EQU	TRUE		; Z180: ENABLE Z180 SYSTEM PERIODIC TIMER
 ;
 RTCIO		.EQU	$0C		; RTC LATCH REGISTER ADR
@@ -82,7 +80,14 @@ LEDMODE		.EQU	LEDMODE_STD	; LEDMODE_[STD|RTC]
 LEDPORT		.EQU	$0E		; STATUS LED PORT ADDRESS
 LEDDISKIO	.EQU	TRUE		; ENABLES DISK I/O ACTIVITY ON STATUS LED
 ;
-DSKYENABLE	.EQU	FALSE		; ENABLES DSKY (DO NOT COMBINE WITH PPIDE)
+DSKYENABLE	.EQU	FALSE		; ENABLES DSKY FUNCTIONALITY
+DSKYDSKACT	.EQU	TRUE		; ENABLES DISK ACTIVITY ON DSKY DISPLAY
+ICMENABLE	.EQU	FALSE		; ENABLES ORIGINAL DSKY ICM DRIVER (7218)
+ICMPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF ICM PPI
+PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
+PKDPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF PKD PPI
+PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
+H8PENABLE	.EQU	FALSE		; ENABLES HEATH H8 FRONT PANEL
 ;
 BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
 CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -125,7 +130,7 @@ DUART1BASE	.EQU	$40		; DUART 1: BASE ADDRESS OF CHIP
 DUART1ACFG	.EQU	DEFSERCFG	; DUART 1A: SERIAL LINE CONFIG
 DUART1BCFG	.EQU	DEFSERCFG	; DUART 1B: SERIAL LINE CONFIG
 ;
-UARTENABLE	.EQU	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+UARTENABLE	.EQU	FALSE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
 UARTOSC		.EQU	1843200		; UART: OSC FREQUENCY IN MHZ
 UARTINTS	.EQU	FALSE		; UART: INCLUDE INTERRUPT SUPPORT UNDER IM1/2/3
 UARTCFG		.EQU	DEFSERCFG | SER_RTS	; UART: LINE CONFIG FOR UART PORTS
@@ -148,7 +153,7 @@ Z2UENABLE	.EQU	FALSE		; Z2U: ENABLE Z280 UART SERIAL DRIVER (Z2U.ASM)
 ;
 ACIAENABLE	.EQU	FALSE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
 ;
-SIOENABLE	.EQU	TRUE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
+SIOENABLE	.EQU	FALSE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
 SIODEBUG	.EQU	FALSE		; SIO: ENABLE DEBUG OUTPUT
 SIOBOOT		.EQU	0		; SIO: REBOOT ON RCV CHAR (0=DISABLED)
 SIOCNT		.EQU	2		; SIO: NUMBER OF CHIPS TO DETECT (1-2), 2 CHANNELS PER CHIP
@@ -179,6 +184,7 @@ TMSMODE		.EQU	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MS
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
@@ -239,6 +245,8 @@ SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 SDCSIOFAST	.EQU	FALSE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
 SDMTSWAP	.EQU	FALSE		; SD: SWAP THE LOGICAL ORDER OF THE SPI PORTS OF THE MT011
 ;
+CHENABLE	.EQU	FALSE		; CH: ENABLE CH375/376 USB SUPPORT
+;
 PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
 PRPSDENABLE	.EQU	TRUE		; PRP: ENABLE PROPIO DRIVER SD CARD SUPPORT
 PRPSDTRACE	.EQU	1		; PRP: SD CARD TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
--- a/Source/HBIOS/cfg_sbc.asm
+++ b/Source/HBIOS/cfg_sbc.asm
@@ -15,7 +15,7 @@
 ;
 #INCLUDE "hbios.inc"
 ;
-PLATFORM	.EQU	PLT_SBC		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO]
+PLATFORM	.EQU	PLT_SBC		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
 CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
@@ -34,7 +34,6 @@ DEFSERCFG	.EQU	SER_38400_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
 ;
 RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
-ROMSIZE_CHK	.EQU	0		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
 MEMMGR		.EQU	MM_SBC		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
 MPCL_RAM	.EQU	$78		; SBC MEM MGR RAM PAGE SELECT REG (WRITE ONLY)
 MPCL_ROM	.EQU	$7C		; SBC MEM MGR ROM PAGE SELECT REG (WRITE ONLY)
@@ -83,6 +82,7 @@ ICMPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF ICM PPI
 PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
 PKDPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF PKD PPI
 PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
+H8PENABLE	.EQU	FALSE		; ENABLES HEATH H8 FRONT PANEL
 ;
 BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
 CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -164,6 +164,7 @@ TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VGASIZ		.EQU	V80X25		; VGA: DISPLAY FORMAT [V80X25|V80X30|V80X43]
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
@@ -224,6 +225,8 @@ SDCNT		.EQU	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT ONLY
 SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 SDCSIOFAST	.EQU	FALSE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
 ;
+CHENABLE	.EQU	FALSE		; CH: ENABLE CH375/376 USB SUPPORT
+;
 PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
 PRPSDENABLE	.EQU	TRUE		; PRP: ENABLE PROPIO DRIVER SD CARD SUPPORT
 PRPSDTRACE	.EQU	1		; PRP: SD CARD TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
--- a/Source/HBIOS/cfg_scz180.asm
+++ b/Source/HBIOS/cfg_scz180.asm
@@ -15,7 +15,7 @@
 ;
 #INCLUDE "hbios.inc"
 ;
-PLATFORM	.EQU	PLT_SCZ180	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO]
+PLATFORM	.EQU	PLT_SCZ180	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
 CPUFAM		.EQU	CPU_Z180	; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
@@ -34,10 +34,8 @@ DEFSERCFG	.EQU	SER_115200_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
 ;
 RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
-ROMSIZE_CHK	.EQU	0		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
 MEMMGR		.EQU	MM_Z180		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
-RAMLOC		.EQU	19		; START OF RAM AS POWER OF 2 (2^N) IN PHYSICAL ADDRESS SPACE
-RAMBIAS		.EQU	(1 << (RAMLOC - 10))	; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
+RAMBIAS		.EQU	ROMSIZE		; OFFSET OF START OF RAM IN PHYSICAL ADDRESS SPACE
 MPGSEL_0	.EQU	$78		; Z2 MEM MGR BANK 0 PAGE SELECT REG (WRITE ONLY)
 MPGSEL_1	.EQU	$79		; Z2 MEM MGR BANK 1 PAGE SELECT REG (WRITE ONLY)
 MPGSEL_2	.EQU	$7A		; Z2 MEM MGR BANK 2 PAGE SELECT REG (WRITE ONLY)
@@ -82,7 +80,14 @@ LEDMODE		.EQU	LEDMODE_STD	; LEDMODE_[STD|RTC]
 LEDPORT		.EQU	$0E		; STATUS LED PORT ADDRESS
 LEDDISKIO	.EQU	TRUE		; ENABLES DISK I/O ACTIVITY ON STATUS LED
 ;
-DSKYENABLE	.EQU	FALSE		; ENABLES DSKY (DO NOT COMBINE WITH PPIDE)
+DSKYENABLE	.EQU	FALSE		; ENABLES DSKY FUNCTIONALITY
+DSKYDSKACT	.EQU	TRUE		; ENABLES DISK ACTIVITY ON DSKY DISPLAY
+ICMENABLE	.EQU	FALSE		; ENABLES ORIGINAL DSKY ICM DRIVER (7218)
+ICMPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF ICM PPI
+PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
+PKDPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF PKD PPI
+PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
+H8PENABLE	.EQU	FALSE		; ENABLES HEATH H8 FRONT PANEL
 ;
 BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
 CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -179,6 +184,7 @@ TMSMODE		.EQU	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MS
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
@@ -239,6 +245,18 @@ SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 SDCSIOFAST	.EQU	FALSE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
 SDMTSWAP	.EQU	FALSE		; SD: SWAP THE LOGICAL ORDER OF THE SPI PORTS OF THE MT011
 ;
+CHENABLE	.EQU	FALSE		; CH: ENABLE CH375/376 USB SUPPORT
+CHTRACE		.EQU	1		; CH: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHUSBTRACE	.EQU	1		; CHUSB: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHSDTRACE	.EQU	1		; CHSD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
+CHCNT		.EQU	1		; CH: NUMBER OF BOARDS TO DETECT (1-2)
+CH0BASE		.EQU	$BE		; CH 0: BASE I/O ADDRESS
+CH0USBENABLE	.EQU	TRUE		; CH 0: ENABLE USB DISK
+CH0SDENABLE	.EQU	FALSE		; CH 0: ENABLE SD DISK
+CH1BASE		.EQU	$FF		; CH 1: BASE I/O ADDRESS
+CH1USBENABLE	.EQU	FALSE		; CH 1: ENABLE USB DISK
+CH1SDENABLE	.EQU	FALSE		; CH 1: ENABLE SD DISK
+;
 PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
 PRPSDENABLE	.EQU	TRUE		; PRP: ENABLE PROPIO DRIVER SD CARD SUPPORT
 PRPSDTRACE	.EQU	1		; PRP: SD CARD TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
--- a/Source/HBIOS/cfg_una.asm
+++ b/Source/HBIOS/cfg_una.asm
@@ -15,7 +15,7 @@
 ;
 #INCLUDE "../UBIOS/ubios.inc"
 ;
-;PLATFORM	.EQU	PLT_UNA		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO]
+;PLATFORM	.EQU	PLT_UNA		; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
 CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_UNA	; HARDWARE BIOS: BIOS_[WBW|UNA]
 ;
--- a/Source/HBIOS/cfg_z80retro.asm
+++ b/Source/HBIOS/cfg_z80retro.asm
@@ -15,7 +15,7 @@
 ;
 #INCLUDE "hbios.inc"
 ;
-PLATFORM	.EQU	PLT_Z80RETRO	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO]
+PLATFORM	.EQU	PLT_Z80RETRO	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
 CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
@@ -34,7 +34,6 @@ DEFSERCFG	.EQU	SER_38400_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
 ;
 RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
-ROMSIZE_CHK	.EQU	0		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
 MEMMGR		.EQU	MM_Z2		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
 MPGSEL_0	.EQU	$60		; Z2 MEM MGR BANK 0 PAGE SELECT REG (WRITE ONLY)
 MPGSEL_1	.EQU	$61		; Z2 MEM MGR BANK 1 PAGE SELECT REG (WRITE ONLY)
@@ -86,6 +85,7 @@ ICMPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF ICM PPI
 PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
 PKDPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF PKD PPI
 PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
+H8PENABLE	.EQU	FALSE		; ENABLES HEATH H8 FRONT PANEL
 ;
 BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
 CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -166,6 +166,7 @@ TMSMODE		.EQU	TMSMODE_NONE	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|M
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
@@ -198,6 +199,8 @@ SDCNT		.EQU	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT ONLY
 SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 SDCSIOFAST	.EQU	FALSE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
 ;
+CHENABLE	.EQU	FALSE		; CH: ENABLE CH375/376 USB SUPPORT
+;
 PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
 ;
 PPPENABLE	.EQU	FALSE		; PPP: ENABLE ZETA PARALLEL PORT PROPELLER BOARD DRIVER (PPP.ASM)
--- a/Source/HBIOS/cfg_zeta.asm
+++ b/Source/HBIOS/cfg_zeta.asm
@@ -15,7 +15,7 @@
 ;
 #INCLUDE "hbios.inc"
 ;
-PLATFORM	.EQU	PLT_ZETA	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO]
+PLATFORM	.EQU	PLT_ZETA	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
 CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; BIOS_[WBW|UNA]: HARDWARE BIOS
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
@@ -34,7 +34,6 @@ DEFSERCFG	.EQU	SER_38400_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
 ;
 RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
-ROMSIZE_CHK	.EQU	0		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
 MEMMGR		.EQU	MM_SBC		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
 MPCL_RAM	.EQU	$78		; SBC MEM MGR RAM PAGE SELECT REG (WRITE ONLY)
 MPCL_ROM	.EQU	$7C		; SBC MEM MGR ROM PAGE SELECT REG (WRITE ONLY)
@@ -75,6 +74,7 @@ ICMPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF ICM PPI
 PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
 PKDPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF PKD PPI
 PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
+H8PENABLE	.EQU	FALSE		; ENABLES HEATH H8 FRONT PANEL
 ;
 BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
 CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -136,6 +136,7 @@ TMSMODE		.EQU	TMSMODE_NONE	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|M
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
@@ -169,6 +170,8 @@ SDCNT		.EQU	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT ONLY
 SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 SDCSIOFAST	.EQU	FALSE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
 ;
+CHENABLE	.EQU	FALSE		; CH: ENABLE CH375/376 USB SUPPORT
+;
 PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
 ;
 PPPENABLE	.EQU	FALSE		; PPP: ENABLE ZETA PARALLEL PORT PROPELLER BOARD DRIVER (PPP.ASM)
--- a/Source/HBIOS/cfg_zeta2.asm
+++ b/Source/HBIOS/cfg_zeta2.asm
@@ -15,7 +15,7 @@
 ;
 #INCLUDE "hbios.inc"
 ;
-PLATFORM	.EQU	PLT_ZETA2	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO]
+PLATFORM	.EQU	PLT_ZETA2	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH|Z80RETRO|S100|DUO|HEATH]
 CPUFAM		.EQU	CPU_Z80		; CPU FAMILY: CPU_[Z80|Z180|Z280]
 BIOS		.EQU	BIOS_WBW	; HARDWARE BIOS: BIOS_[WBW|UNA]
 BATCOND		.EQU	FALSE		; ENABLE LOW BATTERY WARNING MESSAGE
@@ -34,7 +34,6 @@ DEFSERCFG	.EQU	SER_38400_8N1	; DEFAULT SERIAL LINE CONFIG (SEE STD.ASM)
 ;
 RAMSIZE		.EQU	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
 ROMSIZE		.EQU	512		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
-ROMSIZE_CHK	.EQU	0		; ROMSIZE VALUE VERIFICATION (0=DISABLED)
 MEMMGR		.EQU	MM_Z2		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180|Z280|MBC|RPH]
 MPGSEL_0	.EQU	$78		; Z2 MEM MGR BANK 0 PAGE SELECT REG (WRITE ONLY)
 MPGSEL_1	.EQU	$79		; Z2 MEM MGR BANK 1 PAGE SELECT REG (WRITE ONLY)
@@ -86,6 +85,7 @@ ICMPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF ICM PPI
 PKDENABLE	.EQU	FALSE		; ENABLES DSKY NG PKD DRIVER (8259)
 PKDPPIBASE	.EQU	$60		; BASE I/O ADDRESS OF PKD PPI
 PKDOSC		.EQU	3000000		; OSCILLATOR FREQ FOR PKD (IN HZ)
+H8PENABLE	.EQU	FALSE		; ENABLES HEATH H8 FRONT PANEL
 ;
 BOOTCON		.EQU	0		; BOOT CONSOLE DEVICE
 CRTACT		.EQU	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -147,6 +147,7 @@ TMSMODE		.EQU	TMSMODE_NONE	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|M
 TMSTIMENABLE	.EQU	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 VGAENABLE	.EQU	FALSE		; VGA: ENABLE VGA VIDEO/KBD DRIVER (VGA.ASM)
 VRCENABLE	.EQU	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+SCONENABLE	.EQU	FALSE		; SCON: ENABLE S100 CONSOLE DRIVER (SCON.ASM)
 ;
 MDENABLE	.EQU	TRUE		; MD: ENABLE MEMORY (ROM/RAM) DISK DRIVER (MD.ASM)
 MDROM		.EQU	TRUE		; MD: ENABLE ROM DISK
@@ -180,6 +181,8 @@ SDCNT		.EQU	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT ONLY
 SDTRACE		.EQU	1		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)
 SDCSIOFAST	.EQU	FALSE		; SD: ENABLE TABLE-DRIVEN BIT INVERTER IN CSIO MODE
 ;
+CHENABLE	.EQU	FALSE		; CH: ENABLE CH375/376 USB SUPPORT
+;
 PRPENABLE	.EQU	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)
 ;
 PPPENABLE	.EQU	FALSE		; PPP: ENABLE ZETA PARALLEL PORT PROPELLER BOARD DRIVER (PPP.ASM)
--- a/Source/HBIOS/ch.asm
+++ b/Source/HBIOS/ch.asm
--- a/Source/HBIOS/dsrtc.asm
+++ b/Source/HBIOS/dsrtc.asm
@@ -145,6 +145,8 @@ DSRTC_PREINIT:
 	;OR	DSRTC_IDLE		; SET OUR IDLE BITS
 	;LD	(DSRTC_OPRVAL),A	; SAVE IT
 ;
+	XOR	A			; ZERO
+	LD	(DSRTC_STAT),A		; CLEAR STATUS
 	CALL	DSRTC_DETECT		; HARDWARE DETECTION
 	LD	(DSRTC_STAT),A		; SAVE RESULT
 	RET	NZ			; ABORT IF ERROR
--- a/Source/HBIOS/esp.asm
+++ b/Source/HBIOS/esp.asm
@@ -8,7 +8,7 @@
 ;
 ; TODO:
 ; - CLEAR CONSOLE SCREEN AT INITIALIZATION
-; - INITIALIZE BAUD/MODE OF SERIAL INTERFACES AT INITIALIZATION
+; - INITIALIZE BAUD/MODE OF SERIAL INTERFACES AT INITIALIZATION?
 ;
 ESP_IOBASE	.EQU	$9C
 ESP_0_IO	.EQU	ESP_IOBASE + 0
@@ -33,7 +33,8 @@ ESP_1_SPARE	.EQU	%00100000
 ;
 ; COMMAND OPCODES
 ;
-ESP_CMD_NOP	.EQU	0		; NO OP
+ESP_CMD_NOP	.EQU	0		; NO OP/SYNC
+ESP_CMD_SYNC	.EQU	0		; NO OP/SYNC
 ESP_0_CMD_COUT	.EQU	1		; CHAR OUT
 ESP_0_CMD_CSTR	.EQU	2		; STRING OUT
 ESP_0_CMD_KIN	.EQU	3		; KEY IN
@@ -76,11 +77,11 @@ ESP_INIT:
 ;
 ESP_INIT1:
 	CALL	ESP_PRTVER
-	
+
 	LD	A,(ESP_PRES)
 	SET	0,A
 	LD	(ESP_PRES),A
-	
+
 ;
 ESP_INIT2:
 	; DETECT SECOND ESP32 MODULE
@@ -126,27 +127,61 @@ ESP_INIT6:
 ;==================================================================================================
 ;
 ESP_DETECT:
+	; TRY TO DETECT IF PORT IS FLOATING AND
+	; FAIL DETECTION IF SO
+	LD	C,(IY+ESP_CFG_ST)	; ESP STATUS PORT
+	IN	A,(C)			; READ IT
+	;CALL	PC_SPACE		; *DEBUG*
+	;CALL	PRTHEXBYTE		; *DEBUG*
+	AND	%11100000		; ISOLATE TOP 3 BITS
+	CP	$00			; ALWAYS ZERO IF PRESENT
+	RET	NZ			; ABORT ON FAILURE
+;
+	; ESP32 PROCESSOR MAY TAKE A FEW SECONDS TO START UP, SO
+	; HERE WE WAIT FOR BUSY TO CLEAR WITH ABOUT A 5 SECOND TIMEOUT
+	LD	B,0			; LOOP UP TO 256 TIMES
+	LD	C,(IY+ESP_CFG_ST)	; ESP STATUS PORT
+ESP_DETECT1:
+	IN	A,(C)			; GET STATUS
+	AND	(IY+ESP_CFG_BSYMSK)	; IS ESP BUSY?
+	JR	Z,ESP_DETECT2		; MOVE ALONG IF NOT BUSY
+	LD	DE,1500			; 1500 * 16US = 24MS
+	CALL	VDELAY			; DELAY
+	DJNZ	ESP_DETECT1		; LOOP
+	OR	$FF			; SIGNAL FAILURE
+	RET				; DONE
+;
+ESP_DETECT2:
+	CALL 	ESP_SYNC
+	;LD	A,B			; *DEBUG*
+	;CALL	PC_SPACE		; *DEBUG*
+	;CALL	PRTHEXBYTE		; *DEBUG*
 	CALL	ESP_CLR			; CLEAR ANY PENDING DATA
-	RET	NZ			; IF FAILS, ASSUME NOT PRESENT
 	LD	A,ESP_CMD_DISC		; DISCOVER COMMAND
 	CALL	ESP_OUT			; SEND IT
 ;
 	; LOOK FOR SIGNATURE STARTING WITH "ESP"
 	CALL	ESP_INWAIT		; ATTEMPT TO GET CHAR
+	;CALL	PC_SPACE		; *DEBUG*
+	;CALL	PRTHEXBYTE		; *DEBUG*
 	CP	'E'
 	RET	NZ
 	CALL	ESP_INWAIT		; ATTEMPT TO GET CHAR
+	;CALL	PC_SPACE		; *DEBUG*
+	;CALL	PRTHEXBYTE		; *DEBUG*
 	CP	'S'
 	RET	NZ
 	CALL	ESP_INWAIT		; ATTEMPT TO GET CHAR
+	;CALL	PC_SPACE		; *DEBUG*
+	;CALL	PRTHEXBYTE		; *DEBUG*
 	CP	'P'
 	RET
 ;
 ; CLEAR ESP INPUT QUEUE
 ;
 ESP_CLR:
-	LD	B,0			; MAX CHARS TO READ
-ESP_CLR0:
+;	LD	B,0			; MAX CHARS TO READ   /Removed DDW
+;ESP_CLR0:   /Removed DDW
 	CALL	ESP_WTNBSY		; WAIT TILL NOT BUSY
 	RET	NZ			; BAIL OUT IF TIMEOUT
 	IN	A,(ESP_STAT)		; GET STATUS
@@ -154,21 +189,37 @@ ESP_CLR0:
 	RET	Z			; IF NOT, DONE
 	LD	C,(IY+ESP_CFG_IO)	; ESP I/O PORT
 	IN	A,(C)			; GET BYTE
-	DJNZ	ESP_CLR0		; LOOP TILL DONE
-	OR	$FF			; SIGNAL FAILURE
+	JP 	ESP_CLR
+;	DJNZ	ESP_CLR0		; LOOP TILL DONE /Removed DDW
+;	OR	$FF			; SIGNAL FAILURE /Removed DDW
+;	RET /Removed DDW
+
+;
+; RE-SYNC ESP  (added DDW)
+;
+ESP_SYNC:
+	LD	B,0				; sync count -- WORST CASE  PERFORMACE COULD BE IMPROVED BY REDUCING THIS VALUE
+ESP_SYNC0:
+	PUSH 	BC
+	LD	A,ESP_CMD_SYNC		; Sync ESP
+	CALL	ESP_OUT			; SEND CMD OPCODE
+	POP 	BC
+	DJNZ	ESP_SYNC0		; LOOP TILL DONE
 	RET
 ;
 ; PRINT ESP VERSION STRING TO CONSOLE
 ;
 ESP_PRTVER:
+	CALL 	ESP_SYNC
 	CALL	ESP_CLR			; CLEAR ANY PENDING DATA
+	;LD	DE,1000			; SMALL DELAY HERE
+	;CALL	VDELAY			; ... SEEMS TO HELP RELIABILITY
 	LD	A,ESP_CMD_DISC		; DISCOVER COMMAND
 	CALL	ESP_OUT			; SEND IT
 	CALL	ESP_WTRDY		; WAIT FOR READY TO OUTPUT
 ESP_PRTVER1:
 	CALL	ESP_WTNBSY		; WAIT TILL NOT BUSY
 	IN	A,(ESP_STAT)		; GET STATUS
-	;AND	ESP_0_RDY		; ISOLATE OUTPUT READY BIT
 	AND	(IY+ESP_CFG_RDYMSK)	; ISOLATE OUTPUT READY BIT
 	RET	Z			; DONE IF NOTHING READY
 	CALL	ESP_IN			; GET NEXT CHAR
@@ -190,13 +241,13 @@ ESP_OUT:
 ESP_INWAIT:
 	CALL	ESP_WTNBSY		; WAIT TILL NOT BUSY
 	CALL	ESP_WTRDY		; WAIT FOR READY TO OUTPUT
-	; FALL THRU (GET CHAR VIA ESP_IN)
+	JP 		ESP_IN1			; Added DDW
 ;
 ; GET BYTE FROM ESP (NON BLOCKING)
 ;
 ESP_IN:
 	CALL	ESP_WTNBSY		; WAIT TILL NOT BUSY
-ESP_IN1:	
+ESP_IN1:
 	LD	C,(IY+ESP_CFG_IO)	; ESP I/O PORT
 	IN	A,(C)			; GET BYTE
 	PUSH	AF			; SAVE VALUE
@@ -208,20 +259,30 @@ ESP_IN1:
 ;
 ESP_WTNBSY:
 	LD	B,0			; MAX TRIES
-ESP_WTNBSY1:	
+	;PUSH	HL			; SAVE HL
+	;LD	HL,0			; MAX TRIES
+ESP_WTNBSY1:
 	LD	C,(IY+ESP_CFG_ST)	; ESP STATUS PORT
 	IN	A,(C)			; GET STATUS
 	AND	(IY+ESP_CFG_BSYMSK)	; IS ESP BUSY?
 	RET	Z			; RETURN IF NOT BUSY
+	;JR	Z,ESP_WTNBSY_Z		; RETURN IF NOT BUSY
 	DJNZ	ESP_WTNBSY1		; ELSE LOOP
+	;DEC	HL			; DEC LOOP COUNTER
+	;LD	A,H			; CHECK FOR
+	;OR	L			; ... TIMEOUT
+	;JR	NZ,ESP_WTNBSY1		; LOOP AS NEEDED
+	;CALL	PC_ASTERISK		; *DEBUG*
 	OR	$FF			; SIGNAL TIMEOUT
+;ESP_WTNBSY_Z:
+	;POP	HL			; RECOVER HL
 	RET				; AND RETURN
 ;
 ; WAIT FOR ESP TO BE BUSY
 ;
 ESP_WTBSY:
-	LD	B,20			; MAX TRIES
-ESP_WTBSY1:	
+	LD	B,3			; MAX TRIES
+ESP_WTBSY1:
 	LD	C,(IY+ESP_CFG_ST)	; ESP STATUS PORT
 	IN	A,(C)			; GET STATUS
 	XOR	$FF			; INVERT SO 0=BUSY
@@ -230,6 +291,27 @@ ESP_WTBSY1:
 	DJNZ	ESP_WTBSY1		; ELSE LOOP
 	OR	$FF			; SIGNAL TIMEOUT
 	RET				; AND RETURN
+;;;;
+;;;; WAIT FOR ESP TO BE READY TO OUTPUT
+;;;;
+;;;ESP_WTRDY:
+;;;	PUSH	HL			; SAVE HL
+;;;	LD	HL,0			; MAX TRIES
+;;;ESP_WTRDY1:
+;;;	LD	C,(IY+ESP_CFG_ST)	; ESP STATUS PORT
+;;;	IN	A,(C)			; GET STATUS
+;;;	XOR	$FF			; INVERT SO 0=READY
+;;;	AND	(IY+ESP_CFG_RDYMSK)	; IS ESP READY TO OUTPUT
+;;;	JR	Z,ESP_WTRDY_Z		; RETURN IF READY
+;;;	DEC	HL			; DEC LOOP COUNTER
+;;;	LD	A,H			; CHECK FOR
+;;;	OR	L			; ... TIMEOUT
+;;;	JR	NZ,ESP_WTRDY1		; LOOP AS NEEDED
+;;;	CALL	PC_PERIOD		; *DEBUG*
+;;;	OR	$FF			; SIGNAL TIMEOUT
+;;;ESP_WTRDY_Z:
+;;;	POP	HL			; RECOVER HL
+;;;	RET				; AND RETURN
 ;
 ; WAIT FOR ESP TO BE READY TO OUTPUT
 ;
@@ -242,6 +324,8 @@ ESP_WTRDY1:
 	AND	(IY+ESP_CFG_RDYMSK)	; IS ESP READY TO OUTPUT
 	RET	Z			; RETURN IF READY
 	DJNZ	ESP_WTRDY1		; ELSE LOOP
+	;CALL	PC_PERIOD		; *DEBUG*
+	CALL 	ESP_SYNC 		; SOMETHING WENT WRONG, ENSURE SYNC (Added DDW)
 	OR	$FF			; SIGNAL TIMEOUT
 	RET				; AND RETURN
 ;
@@ -327,6 +411,7 @@ ESPCON_IN:
 ;
 ;
 ESPCON_IST:
+	CALL	ESP_CLR			; CLEAR ANY PENDING DATA (Added DDW)
 	LD	A,ESP_0_CMD_KST		; KBD BUF STATUS
 	CALL	ESP_OUT			; SEND CMD OPCODE
 	CALL	ESP_INWAIT		; GET BUF SIZE
@@ -357,7 +442,9 @@ ESPCON_OST:
 ;
 ;
 ESPCON_INITDEV:
-	SYSCHKERR(ERR_NOTIMPL)
+	CALL 	ESP_CLR
+	CALL 	ESP_SYNC
+;	SYSCHKERR(ERR_NOTIMPL)  Removed DDW
 	RET
 ;
 ;
@@ -463,6 +550,7 @@ ESPSER_IN:
 ;
 ;
 ESPSER_IST:
+	CALL	ESP_CLR			; CLEAR ANY PENDING DATA (Added DDW)
 	LD	A,ESP_CMD_SST		; SERIAL STATUS
 	CALL	ESP_OUT			; SEND CMD OPCODE
 	CALL	ESP_INWAIT		; GET BUF SIZE
@@ -493,6 +581,8 @@ ESPSER_OST:
 ;
 ;
 ESPSER_INITDEV:
+	CALL 	ESP_CLR
+	CALL 	ESP_SYNC
 	PUSH	DE			; SAVE INCOMING CONFIG WORD
 ;
 	; XLATE NEW LINE MODE INTO C
--- a/Source/HBIOS/fd.asm
+++ b/Source/HBIOS/fd.asm
@@ -811,19 +811,27 @@ FD_DETECT:
 	IN	A,(FDC_MSR)	; READ MSR
 	;CALL	PC_SPACE	; *DEBUG*
 	;CALL	PRTHEXBYTE	; *DEBUG*
-	CP	$80
-	JR	Z,FD_DETECT1	; $80 IS OK
-	CP	$D0
-	JR	Z,FD_DETECT1	; $D0 IS OK
-	RET			; NOPE, ABORT WITH ZF=NZ
-;
-FD_DETECT1:
-	CALL	DLY32		; WAIT A BIT FOR FDC
-	IN	A,(FDC_MSR)	; READ MSR AGAIN
+	
+	CP	$D0		; SPECIAL CASE: DATA PENDING?
+	JR	NZ,FD_DETECT1	; NOPE, MOVE ALONG
+	IN	A,(FDC_DATA)	; SWALLOW THE PENDING DATA
+	CALL	DLY32		; SETTLE
+	IN	A,(FDC_MSR)	; ... AND REREAD THE STATUS
 	;CALL	PC_SPACE	; *DEBUG*
 	;CALL	PRTHEXBYTE	; *DEBUG*
-	CP	$80
-	RET			; $80 OK, ELSE NOT PRESENT
+
+FD_DETECT1:
+	CP	$80		; WE EXPECT $80
+	RET	Z		; IF SO, ALL DONE
+
+	; WE HAVE SEEN AN FDC THAT NEEDS A SECOND READ TO GET
+	; DESIRED VALUE, SO TRY ONE MORE TIME
+	CALL	DLY32		; WAIT A BIT
+	IN	A,(FDC_MSR)	; ... AND REREAD THE STATUS
+	;CALL	PC_SPACE	; *DEBUG*
+	;CALL	PRTHEXBYTE	; *DEBUG*
+	CP	$80		; CHECK FOR CORRECT VALUE
+	RET			; RETURN WITH ZF ACCORDING TO RESULT
 ;
 ; UNIT INITIALIZATION
 ;
--- a/Source/HBIOS/h8p.asm
+++ b/Source/HBIOS/h8p.asm
@@ -0,0 +1,162 @@
+;
+;==================================================================================================
+; HEATH H8 FRONT PANEL (DISPLAY AND KEYBOARD) ROUTINES
+;==================================================================================================
+;
+; LED SEGMENTS (BIT VALUES)
+;
+;	+--02--+
+;	40    04
+;	+--01--+
+;	20    08
+;	+--10--+  80
+;
+;__H8P_PREINIT_______________________________________________________________________________________
+;
+;  CONFIGURE AND RESET PANEL
+;____________________________________________________________________________________________________
+;
+; HARDWARE RESET PRIOR TO ROMWBW CONSOLE INITIALIZATION
+;
+H8P_PREINIT:
+	LD	A,(DSKY_DISPACT)	; DSKY DISPATCHER ALREADY SET?
+	OR	A			; SET FLAGS
+	RET	NZ			; IF ALREADY ACTIVE, ABORT
+;
+	; REGISTER DRIVER WITH HBIOS
+	LD	BC,H8P_DISPATCH
+	CALL	DSKY_SETDISP
+;
+	RET
+;
+;__H8P_INIT__________________________________________________________________________________________
+;
+;  DISPLAY DSKY INFO ON ROMWBW CONSOLE
+;____________________________________________________________________________________________________
+;
+H8P_INIT:
+	CALL	NEWLINE			; FORMATTING
+	PRTS("H8P:$")			; DRIVER TAG
+;
+	RET				; DONE
+;
+; DSKY DEVICE FUNCTION DISPATCH ENTRY
+;   A: RESULT (OUT), 0=OK, Z=OK, NZ=ERR
+;   B: FUNCTION (IN)
+;
+H8P_DISPATCH:
+	LD	A,B			; GET REQUESTED FUNCTION
+	AND	$0F			; ISOLATE SUB-FUNCTION
+	JP	Z,H8P_RESET		; RESET DSKY HARDWARE
+	DEC	A	
+	JP	Z,H8P_STAT		; GET KEYPAD STATUS
+	DEC	A	
+	JP	Z,H8P_GETKEY		; READ A KEY FROM THE KEYPAD
+	DEC	A	
+	JP	Z,H8P_SHOWHEX		; DISPLAY A 32-BIT BINARY VALUE IN HEX
+	DEC	A	
+	JP	Z,H8P_SHOWSEG		; DISPLAY SEGMENTS
+	DEC	A	
+	JP	Z,H8P_KEYLEDS		; SET KEYPAD LEDS
+	DEC	A	
+	JP	Z,H8P_STATLED		; SET STATUS LED
+	DEC	A	
+	JP	Z,H8P_BEEP		; BEEP DSKY SPEAKER
+	DEC	A
+	JP	Z,H8P_DEVICE		; DEVICE INFO
+	SYSCHKERR(ERR_NOFUNC)
+	RET
+;
+; RESET DSKY -- CLEAR DISPLAY AND KEYPAD FIFO
+;
+H8P_RESET:
+	XOR	A			; SIGNAL SUCCESS
+	RET
+;
+;  CHECK FOR KEY PRESS, SAVE RAW VALUE, RETURN STATUS
+;
+H8P_STAT:
+	XOR	A			; ZERO KEYS PENDING (FOR NOW)
+	RET
+;
+;  WAIT FOR A DSKY KEYPRESS AND RETURN
+;
+H8P_GETKEY:
+	; PUT KEY VALUE IN REGISTER E
+	XOR	A			; SIGNAL SUCCESS	
+	RET
+;
+; DISPLAY HEX VALUE FROM DE:HL
+;
+H8P_SHOWHEX:
+	LD	BC,DSKY_HEXBUF		; POINT TO HEX BUFFER
+	CALL	ST32			; STORE 32-BIT BINARY THERE
+	LD	HL,DSKY_HEXBUF		; FROM: BINARY VALUE (HL)
+	LD	DE,DSKY_BUF		; TO: SEGMENT BUFFER (DE)
+	CALL	DSKY_BIN2SEG		; CONVERT
+	LD	HL,DSKY_BUF		; POINT TO SEGMENT BUFFER
+	; AND FALL THRU TO DISPLAY IT
+;
+; DISPLAY BYTE VALUES POINTED TO BY DE.  THE INCOMING BYTES ARE IN
+; THE STANDARD ROMWBW SEGMENT ENCODING AND MUST BE TRANSLATED TO THE
+; HEATH ENCODING (SEE ICM.ASM FOR EXAMPLE):
+;
+;
+;	From:		To:
+;	+--01--+	+--02--+
+;	20    02	40    04
+;	+--40--+	+--01--+
+;	10    04	20    08
+;	+--08--+  80	+--10--+  80
+;
+H8P_SHOWSEG:
+	XOR	A			; SIGNAL SUCCESS
+	RET
+;
+; UPDATE KEY LEDS (H8 HAS NONE)
+;
+H8P_KEYLEDS:
+	XOR	A			; SIGNAL SUCCESS
+	RET
+;
+; SET STATUS LEDS BASED ON BITS IN E
+;
+H8P_STATLED:
+	XOR	A			; SIGNAL SUCCESS
+	RET
+;
+; BEEP THE SPEAKER ON THE H8P
+;
+H8P_BEEP:
+	POP	BC
+	XOR	A			; SIGNAL SUCCESS
+	RET
+;
+; DEVICE INFORMATION
+;
+H8P_DEVICE:
+	LD	D,DSKYDEV_H8P		; D := DEVICE TYPE
+	LD	E,0			; E := PHYSICAL DEVICE NUMBER
+	LD	H,0			; H := MODE
+	LD	L,0			; L := BASE I/O ADDRESS
+	XOR	A			; SIGNAL SUCCESS
+	RET
+;
+;_KEYMAP_TABLE_____________________________________________________________________________________________________________
+;
+H8P_KEYMAP:	; *** NEEDS TO BE UPDATED ***
+	; POS	$00  $01  $02  $03  $04  $05  $06  $07
+	; KEY   [0]  [1]  [2]  [3]  [4]  [5]  [6]  [7]
+	.DB	$0D, $04, $0C, $14, $03, $0B, $13, $02
+;
+	; POS	$08  $09  $0A  $0B  $0C  $0D  $0E  $0F
+	; KEY   [8]  [9]  [A]  [B]  [C]  [D]  [E]  [F]
+	.DB	$0A, $12, $01, $09, $11, $00, $08, $10
+;
+	; POS	$10  $11  $12  $13  $14  $15  $16  $17
+	; KEY   [FW] [BK] [CL] [EN] [DE] [EX] [GO] [BO]
+	.DB	$05, $15, $1D, $1C, $1B, $1A, $19, $18
+
+	; POS	$18  $19  $1A  $1B
+	; KEY   [F4] [F3] [F2] [F1]
+	.DB	$23, $22, $21, $20
--- a/Source/HBIOS/hbios.asm
+++ b/Source/HBIOS/hbios.asm
@@ -88,20 +88,6 @@ MODCNT	.SET	MODCNT + 1
 	!!!	; FORCE AN ASSEMBLY ERROR
 #ENDIF
 ;
-; SOME HARDWARE REQUIRES A SPECIFIC ROMSIZE (NOTABLY ZZRCC) OR THE
-; RESULTING BUILD IMAGES WILL BE CORRUPT.  ROMSIZE_CHK IS SPECIFIED
-; IN THE CONFIG FILE AND IS VERIFIED AGAINST THE ROMSIZE BEING USED
-; BY THE BUILD.  A ROMSIZE_CHK VALUE OF 0 INDICATES THE VERIFICATION
-; IS DISABLED (WHICH IT USUALLY IS).
-;
-#IF (ROMSIZE_CHK != 0) & (ROMSIZE != ROMSIZE_CHK)
-	.ECHO	"*** ERROR: ROMSIZE VALUE VERIFICATION FAILURE.\n"
-	.ECHO	"THIS CONFIGURATION REQUIRES A ROMSIZE OF " \ .ECHO ROMSIZE_CHK \ .ECHO ".\n"
-	.ECHO	"BUILD IS USING A ROMSIZE OF " \ .ECHO ROMSIZE \ .ECHO ".\n"
-	.ECHO	"SEE COMMENTS IN HBIOS.ASM.\n"
-	!!!	; FORCE AN ASSEMBLY ERROR
-#ENDIF
-;
 ;
 ;
 #IF (FPLED_ENABLE)
@@ -196,7 +182,13 @@ MODCNT	.SET	MODCNT + 1
  #ENDIF
 #ENDIF
 ;
+; CONVERT ROMWBW LOGICAL BANK ID TO PHYSICAL 32K BANK OFFSET
 ;
+#DEFINE PBANK(X) (((X >> 7) * (RAMBIAS / 32)) + (X & $7F))
+;
+; CONVERT ROMWBW LOGICAL BANK ID TO Z280 PHYSICAL BANK (4K) OFFSET
+;
+#DEFINE Z2_BANK(X) (PBANK(X) << 3)
 ;
 ; THE RTCDEF EQUATE IS INITIALIZED HERE AND UPDATED BY DRIVER INCLUDES
 ; THAT SHARE THE RTC LATCH.  AS EACH DRIVER FILE IS INCLUDED, IT CAN
@@ -318,9 +310,9 @@ CB_BIDUSR	.DB	BID_USR
 CB_BIDBIOS	.DB	BID_BIOS
 CB_BIDAUX	.DB	BID_AUX
 CB_BIDRAMD0	.DB	BID_RAMD0
-CB_BIDRAMDN	.DB	BID_RAMDN
+CB_RAMD_BNKS	.DB	RAMD_BNKS
 CB_BIDROMD0	.DB	BID_ROMD0
-CB_BIDROMDN	.DB	BID_ROMDN
+CB_ROMD_BNKS	.DB	ROMD_BNKS
 ;
 	.FILL	(HCB + HCB_SIZ - $),0	; PAD REMAINDER OF HCB
 ;
@@ -1112,12 +1104,6 @@ Z280_BOOTERR	.TEXT	"\r\n\r\n*** Application mode boot not supported under Z280 n
 	DI				; NO INTERRUPTS
 	IM	1			; INTERRUPT MODE 1
 ;
-#IF ((PLATFORM == PLT_DUO) & FALSE)
-	; WAIT A WHILE
-	LD	B,0
-	DJNZ	$
-#ENDIF
-;
 #IF ((PLATFORM == PLT_DUO) & TRUE)
 	; WAIT A WHILE
 	LD	HL,0
@@ -1228,14 +1214,14 @@ Z280_BOOTPDRTBL:
 	.DW	($006 << 4) | $A
 	.DW	($007 << 4) | $A
 	; UPPER 32 K (COMMON)
-	.DW	(((((BID_COM & $7F) * 8) + 0) + (1 << (RAMLOC - 12))) << 4) | $A
-	.DW	(((((BID_COM & $7F) * 8) + 1) + (1 << (RAMLOC - 12))) << 4) | $A
-	.DW	(((((BID_COM & $7F) * 8) + 2) + (1 << (RAMLOC - 12))) << 4) | $A
-	.DW	(((((BID_COM & $7F) * 8) + 3) + (1 << (RAMLOC - 12))) << 4) | $A
-	.DW	(((((BID_COM & $7F) * 8) + 4) + (1 << (RAMLOC - 12))) << 4) | $A
-	.DW	(((((BID_COM & $7F) * 8) + 5) + (1 << (RAMLOC - 12))) << 4) | $A
-	.DW	(((((BID_COM & $7F) * 8) + 6) + (1 << (RAMLOC - 12))) << 4) | $A
-	.DW	(((((BID_COM & $7F) * 8) + 7) + (1 << (RAMLOC - 12))) << 4) | $A
+	.DW	((Z2_BANK(BID_COM) + 0) << 4) | $A
+	.DW	((Z2_BANK(BID_COM) + 1) << 4) | $A
+	.DW	((Z2_BANK(BID_COM) + 2) << 4) | $A
+	.DW	((Z2_BANK(BID_COM) + 3) << 4) | $A
+	.DW	((Z2_BANK(BID_COM) + 4) << 4) | $A
+	.DW	((Z2_BANK(BID_COM) + 5) << 4) | $A
+	.DW	((Z2_BANK(BID_COM) + 6) << 4) | $A
+	.DW	((Z2_BANK(BID_COM) + 7) << 4) | $A
 ;
 Z280_INITZ:
 ;
@@ -1441,7 +1427,7 @@ S100MON_SKIP:
 ;
 ; THIS VALUE IS TEMPORARILY STORED AT HBX_LOC - 2
 ; BECAUSE WE ARE CURRENTLY RUNNING IN ROM.  AFTER WE TRANSITION HBIOS
-; TO RAM, THE VALUE IS MOVED TO IT'S REAL LCOATION AT HB_APPBNK.
+; TO RAM, THE VALUE IS MOVED TO IT'S REAL LOCATION AT HB_APPBNK.
 ;
 	LD	A,(HB_CURBNK)		; GET HB_CURBNK
 	LD	(HBX_LOC - 2),A		; ... AND SAVE TEMP FOR APPBNK
@@ -1613,67 +1599,18 @@ MBC_SINGLE:
 ;
 #ENDIF
 ;
-; IF THIS IS A ROM-LESS SYSTEM, THEN WE NEED TO COPY THE PAYLOAD
-; (LOADER, MONITOR, ZSDOS) THAT HAS BEEN LOADED TO PHYSICAL RAM
-; BANKS 0 AND 1 TO THE USER TPA BANK TO RUN AFTER BOOT.
-; IT IS DONE PRIOR TO COPYING HBIOS TO IT'S FINAL BANK BECAUSE
-; THE PAYLOAD MAY EXTEND INTO THE HBIOS OPERATING BANK.  THIS
-; HAPPENS PRIMARILY IN THE CASE WHERE THE
-; SYSTEM HAS THE MINIMUM 128KB OF RAM.
-;
-#IFDEF ROMBOOT
-  #IF (ROMSIZE == 0)
- ; 
-	; THE PAYLOAD IS LIKELY TO CROSS OVER THE RAM BANK 0/1
-	; BOUNDARY.  BNKCPY DOES NOT HANDLE THIS BECAUSE IT ASSUMES
-	; THE COMMON BANK IS USED AFTER PASSING OVER THE BANK
-	; BOUNDARY.  WE WORK AROUND THAT HERE BY DOING TWO COPIES.
-	; THE FIRST ONE HANDLES THE PORTION OF THE PAYLOAD FROM THE
-	; END OF HBIOS TO THE BANK BOUNDARY ($8000).  THE SECOND
-	; ONE HANDLES THE PORTION THAT EXTENDS INTO THE SECOND
-	; PHYSICAL RAM BANK.
-;
-	; COPY PORTION OF PAYLOAD FOLLOWING HBIOS TO THE BANK
-	; BOUNDARY AT $8000 INTO START OF TPA.
-	LD	A,BID_RAM0
-	LD	(HB_SRCBNK),A
-	LD	A,BID_USR
-	LD	(HB_DSTBNK),A
-	LD	HL,HB_END
-	LD	DE,0
-	LD	BC,$8000-HB_END
-;
-    #IF (MEMMGR == MM_Z280)
-	CALL	Z280_BNKCPY
-    #ELSE
-	CALL	HBX_BNKCPY
-    #ENDIF
-;
-	; COPY REMAINDER OF PAYLOAD EXTENDING INTO THE SECOND PHYSICAL
-	; RAM BANK.  NOTE THAT THE DESTINATION ADDRESS (DE) IS
-	; ALREADY CORRECT FROM THE PRIOR COPY.
-	LD	A,BID_RAM0+1
-	LD	(HB_SRCBNK),A
-	LD	HL,$0000
-	; DE IS ALREADY CORRECT
-	LD	BC,$8000-($8000-HB_END)
-;
-    #IF (MEMMGR == MM_Z280)
-	CALL	Z280_BNKCPY
-    #ELSE
-	CALL	HBX_BNKCPY
-    #ENDIF
-;
-  #ENDIF
-;
-#ENDIF
-;
 ; IF ALREADY EXECUTING IN RAM, BYPASS RAM BANK INSTALLATION
 ;
 	LD	A,(HB_RAMFLAG)
 	OR	A
 	JR	NZ,HB_START1
 ;
+; IF BID_BOOT AND BID_BIOS ARE THE SAME, THEN IT IS NEVER APPROPRIATE
+; TO COPY THE HBIOS IMAGE FROM BID_BOOT TO BID_BIOS.  THIS IS TYPICALLY
+; THE CASE FOR A ROMLESS SYSTEM.
+;
+#IF (BID_BOOT != BID_BIOS)
+;
 ; INSTALL HBIOS IN RAM BANK
 ;
 	LD	A,(HB_CURBNK)
@@ -1683,24 +1620,26 @@ MBC_SINGLE:
 	LD	HL,0
 	LD	DE,0
 	LD	BC,$8000
-#IF (MEMMGR == MM_Z280)
+  #IF (MEMMGR == MM_Z280)
 	CALL	Z280_BNKCPY
-#ELSE
+  #ELSE
 	CALL	HBX_BNKCPY
-#ENDIF
+  #ENDIF
 ;
 ; TRANSITION TO HBIOS IN RAM BANK
 ;
-#IF (MEMMGR == MM_Z280)
+  #IF (MEMMGR == MM_Z280)
 	LD	A,BID_BIOS
 	LD	B,$10			; FIRST SYSTEM PDR
 	CALL	Z280_BNKSEL
 	JR	HB_START1
-#ELSE
+  #ELSE
 	LD	A,BID_BIOS		; BIOS BANK ID
 	LD	IX,HB_START1		; EXECUTION RESUMES HERE
 	CALL	HBX_BNKCALL		; CONTINUE IN RAM BANK, DO NOT RETURN
 	HALT				; WE SHOULD NOT COME BACK HERE!
+  #ENDIF
+;
 #ENDIF
 ;
 HB_RAMFLAG	.DB	FALSE		; INITIALLY FALSE, SET TO TRUE BELOW AFTER RAM TRANSITION
@@ -1718,10 +1657,6 @@ HB_START1:				; BNKCALL ARRIVES HERE, BUT NOW RUNNING IN RAM BANK
 	; NOTIFY THAT WE MADE THE TRANSITION!
 	DIAG(DIAG_03)
 	LED(%00000010)
-;
-	; SET THE IN-RAM FLAG
-	LD	A,TRUE			; ACCUM := TRUE
-	LD	(HB_RAMFLAG),A		; SET RAMFLAG
 ;
 	; RECOVER DATA PASSED PRIOR TO RAM TRANSITION
 	; (HBX_LOC - 1) = BATCOND, (HBX_LOC - 2) = APPBNK
@@ -1739,7 +1674,7 @@ HB_START1:				; BNKCALL ARRIVES HERE, BUT NOW RUNNING IN RAM BANK
 	; HL IS TOP 16 BITS OF PHYSICAL ADDRESS OF IVT
 	; IVT *MUST* BE ON A 4K BOUNDARY
 	LD	C,Z280_VPR
-	LD	HL,0 + ((((BID_BIOS & $7F) * 8) + (1 << (RAMLOC - 12))) << 4) + (Z280_IVT >> 8)
+	LD	HL,0 + (((PBANK(BID_BIOS) << 15) + Z280_IVT) >> 8)
 	LDCTL	(C),HL
 #ENDIF
 ;
@@ -1920,6 +1855,14 @@ HB_CPU1:
 	LD	A,L
 	LD	(HB_CPUTYPE),A
 ;
+; CLEAR DISPATCH TABLE ENTRIES
+;
+	XOR	A		; ZERO
+	LD	(CIO_CNT),A	; CIO DEVICES
+	LD	(DIO_CNT),A	; DIO DEVICES
+	LD	(VDA_CNT),A	; VDA DEVICES
+	LD	(SND_CNT),A	; SND DEVICES
+;
 #IF (DSRTCENABLE)
 	CALL	DSRTC_PREINIT
 #ENDIF
@@ -1928,12 +1871,14 @@ HB_CPU1:
  #IF (ICMENABLE)
 	CALL	ICM_PREINIT
  #ENDIF
-#ENDIF
 ;
-#IF (DSKYENABLE)
  #IF (PKDENABLE)
 	CALL	PKD_PREINIT
  #ENDIF
+;
+  #IF (H8PENABLE)
+	CALL	H8P_PREINIT
+  #ENDIF
 #ENDIF
 ;
 #IF (DSKYENABLE)
@@ -2725,13 +2670,13 @@ HB_CKBNK:
 	LD	BC,1			; DECREMENT VALUE
 	XOR	A			; ZERO ACCUM
 HB_CKBNK1:
-#IF (MEMMGR == MM_Z280)
+    #IF (MEMMGR == MM_Z280)
 	LD	D,A			; WORKING VALUE TO D
 	LDUD	A,(HL)			; GRAB NEXT BYTE FROM USER SPACE
 	ADD	A,D			; ADD NEXT BYTE
-#ELSE
+    #ELSE
 	ADD	A,(HL)			; ADD NEXT BYTE
-#ENDIF
+    #ENDIF
 	OR	A			; CLEAR CARRY
 	SBC	HL,BC			; DECREMENT
 	JR	NC,HB_CKBNK1		; LOOP TILL DONE
@@ -2847,6 +2792,12 @@ HB_WDZ:
 	BIT	6,A			; BIT 6 HAS CONFIG JUMPER STATE
 	JR	Z,INITSYS3		; Z=SHORTED, BYPASS CONSOLE SWITCH
  #ENDIF
+;
+  #IF (PLATFORM == PLT_S100)
+	IN	A,($75)			; GET IO BYTE
+	AND	%00000001		; ISOLATE CONSOLE BIT
+	JR	NZ,INITSYS3		; NOT SET, BYPASS CONSOLE SWITCH
+  #ENDIF
 ;
 	LD	A,(CB_CRTDEV)		; GET CRT DISPLAY DEVICE
 	LD	(HB_NEWCON),A		; AND QUEUE TO SWITCH
@@ -3102,11 +3053,7 @@ INITSYS4:
 ; CHAIN TO LOADER
 ;
 #IFDEF ROMBOOT
-  #IF (ROMSIZE > 0)
 	LD	A,BID_IMG0		; CHAIN TO OS IMAGES BANK
-  #ELSE
-	LD	A,BID_USR		; CHAIN TO USER BANK
-  #ENDIF
 #ELSE
 	LD	A,BID_USR		; CHAIN TO USER BANK
 #ENDIF
@@ -3196,6 +3143,9 @@ HB_PCINITTBL:
 #IF (TMSENABLE)
 	.DW	TMS_PREINIT
 #ENDIF
+#IF (SCONENABLE)
+	.DW	SCON_PREINIT
+#ENDIF
 HB_PCINITTBLLEN	.EQU	(($ - HB_PCINITTBL) / 2)

 ;==================================================================================================
@@ -3216,11 +3166,12 @@ HB_INITTBL:
  #IF (ICMENABLE)
 	.DW	ICM_INIT
  #ENDIF
-#ENDIF
-#IF (DSKYENABLE)
  #IF (PKDENABLE)
 	.DW	PKD_INIT
  #ENDIF
+  #IF (H8PENABLE)
+	.DW	H8P_INIT
+  #ENDIF
 #ENDIF
 #IF (AY38910ENABLE)
 	.DW	AY38910_INIT		; AUDIBLE INDICATOR OF BOOT START
@@ -3300,6 +3251,9 @@ HB_INITTBL:
 #IF (TMSENABLE)
 	.DW	TMS_INIT
 #ENDIF
+#IF (SCONENABLE)
+	.DW	SCON_INIT
+#ENDIF
 #IF (VRCENABLE)
 	.DW	VRC_INIT
 #ENDIF
@@ -3342,6 +3296,9 @@ HB_INITTBL:
 #IF (PPPENABLE)
 	.DW	PPP_INIT
 #ENDIF
+#IF (CHENABLE)
+	.DW	CH_INIT
+#ENDIF
 #IF (ESPENABLE)
 	.DW	ESP_INIT
 #ENDIF
@@ -4137,10 +4094,6 @@ SYS_RESINT:
 ; GO BACK TO ROM BOOT LOADER
 ;
 SYS_RESWARM:
-;
-#IF (ROMSIZE == 0)
-	JR	SYS_RESCOLD
-#ENDIF
 ;
 	CALL	SYS_RESINT
 ;
@@ -4159,13 +4112,6 @@ SYS_RESWARM:
 ;
 SYS_RESCOLD:
 ;
-#IF (ROMSIZE == 0)
-	LD	DE,STR_RESTART
-	CALL	Z,WRITESTR
-	DI
-	HALT
-#ENDIF
-;
 #IF (MEMMGR == MM_Z280)
 	JP	Z280_RESTART
 #ELSE
@@ -5843,7 +5789,7 @@ Z280_BNKSEL:
 	LDCTL	HL,(C)			; GET CURRENT I/O PAGE
 	PUSH	HL			; SAVE IT
 	LD	L,$FF			; NEW I/O PAGE
-	LDCTL	(C),HL
+	LDCTL	(C),HL			; IMPLEMENT
 ;
 	; CONVERT BANK ID TO TOP 12 BITS OF PHYSICAL ADDRESS
 	; WITH $0A IN THE LOW ORDER NIBBLE:
@@ -5854,8 +5800,10 @@ Z280_BNKSEL:
 	MULTU	A,$80			; HL=0R00 0BBB B000 0000
 	BIT	6,H			; RAM BIT SET?
 	JR	Z,Z280_BNKSEL2		; IF NOT, ALL DONE
-	RES	6,H			; OTHERWISE, MOVE RAM BIT
-	SET	RAMLOC-16,H		; HL=0000 RBBB B000 0000
+	RES	6,H			; OTHERWISE, REMOVE RAM BIT
+	LD	A,RAMBIAS >> 6		; RAM OFFSET (TOP 8 BITS)
+	OR	H			; RECOMBINE
+	LD	H,A			; AND PUT BACK IN H
 ;
 Z280_BNKSEL2:
 ;
@@ -6103,10 +6051,12 @@ Z2DMAADR1:
 	; MOVE THE RAM/ROM BIT.
 	; RCBUS DMA HI=0000 RBBB BAAA 1111 LO=1111 AAAA AAAA AAAA
 	; ZZ80MB DMA HI=R000 0BBB BAAA 1111 LO=1111 AAAA AAAA AAAA
-	BIT	6,H
-	JR	Z,Z2DMAADR2
-	RES	6,H
-	SET	RAMLOC-16,H
+	BIT	6,H			; RAM BIT SET?
+	JR	Z,Z2DMAADR2		; IF NOT, ALL DONE
+	RES	6,H			; OTHERWISE, REMOVE RAM BIT
+	LD	A,RAMBIAS >> 6		; RAM OFFSET (TOP 8 BITS)
+	OR	H			; RECOMBINE
+	LD	H,A			; AND PUT BACK IN H
 ;
 Z2DMAADR2:
 	PUSH	HL			; SAVE IT FOR NOW
@@ -6157,9 +6107,7 @@ SIZ_ICM	.EQU	$ - ORG_ICM
 		.ECHO	SIZ_ICM
 		.ECHO	" bytes.\n"
  #ENDIF
-#ENDIF
 ;
-#IF (DSKYENABLE)
  #IF (PKDENABLE)
 ORG_PKD	.EQU	$
  #INCLUDE "pkd.asm"
@@ -6168,6 +6116,15 @@ SIZ_PKD	.EQU	$ - ORG_PKD
 		.ECHO	SIZ_PKD
 		.ECHO	" bytes.\n"
  #ENDIF
+;
+  #IF (H8PENABLE)
+ORG_H8P	.EQU	$
+  #INCLUDE "h8p.asm"
+SIZ_H8P	.EQU	$ - ORG_H8P
+		.ECHO	"H8P occupies "
+		.ECHO	SIZ_H8P
+		.ECHO	" bytes.\n"
+  #ENDIF
 #ENDIF
 ;
 #IF (DSRTCENABLE)
@@ -6361,12 +6318,21 @@ SIZ_VDU		.EQU	$ - ORG_VDU
 #IF (TMSENABLE)
 ORG_TMS		.EQU	$
  #INCLUDE "tms.asm"
-SIZ_TMS		.EQU	$ - ORG_TMS
+SIZ_TMS	.EQU	$ - ORG_TMS
 		.ECHO	"TMS occupies "
 		.ECHO	SIZ_TMS
 		.ECHO	" bytes.\n"
 #ENDIF
 ;
+#IF (SCONENABLE)
+ORG_SCON		.EQU	$
+  #INCLUDE "scon.asm"
+SIZ_SCON	.EQU	$ - ORG_SCON
+		.ECHO	"SCON occupies "
+		.ECHO	SIZ_SCON
+		.ECHO	" bytes.\n"
+#ENDIF
+;
 #IF (GDCENABLE)
 ORG_GDC	.EQU	$
  #INCLUDE "gdc.asm"
@@ -6500,6 +6466,15 @@ SIZ_PPP		.EQU	$ - ORG_PPP
 		.ECHO	" bytes.\n"
 #ENDIF
 ;
+#IF (CHENABLE)
+ORG_CH		.EQU	$
+  #INCLUDE "ch.asm"
+SIZ_CH		.EQU	$ - ORG_CH
+		.ECHO	"CH occupies "
+		.ECHO	SIZ_CH
+		.ECHO	" bytes.\n"
+#ENDIF
+;
 #IF (ESPENABLE)
 ORG_ESP		.EQU	$
  #INCLUDE "esp.asm"
@@ -7373,6 +7348,8 @@ PS_DDHDSK	.TEXT	"HDSK$"
 PS_DDPPA	.TEXT	"PPA$"
 PS_DDIMM	.TEXT	"IMM$"
 PS_DDSYQ	.TEXT	"SYQ$"
+PS_DDCHUSB	.TEXT	"CHUSB$"
+PS_DDCHSD	.TEXT	"CHSD$"
 ;
 ; DISK TYPE STRINGS
 ;
@@ -7420,6 +7397,7 @@ PS_SDZ2U	.TEXT	"Z2U$"
 PS_SDLPT	.TEXT	"LPT$"
 PS_SDESPCON	.TEXT	"ESPCON$"
 PS_SDESPSER	.TEXT	"ESPSER$"
+PS_SDSCON	.TEXT	"SCON$"
 ;
 ; CHARACTER SUB TYPE STRINGS
 ;
@@ -7764,7 +7742,6 @@ STR_LOWBAT	.DB	"\r\n\r\n+++ LOW BATTERY +++$"
 STR_PANIC	.TEXT	"\r\n>>> PANIC: $"
 STR_SYSCHK	.TEXT	"\r\n>>> SYSCHK: $"
 STR_CONTINUE	.TEXT	"\r\nContinue (Y/N)? $"
-STR_RESTART	.TEXT	"\r\n\r\n>>> Press hardware reset button to restart system\r\n\r\n$"
 ;
 #IF (DSKYENABLE)	;	'H','B','I','O',' ',' ',' ',' '
 MSG_HBVER		.DB	$76,$7F,$30,$3F,$00,$00,$00,$00	; "HBIO    "
--- a/Source/HBIOS/hbios.inc
+++ b/Source/HBIOS/hbios.inc
@@ -152,6 +152,7 @@ PLT_RPH		.EQU	14		; RHYOPHYRE GRAPHICS COMPUTER
 PLT_Z80RETRO	.EQU	15		; Z80 RETRO COMPUTER
 PLT_S100	.EQU	16		; S100 COMPUTERS Z180 SYSTEM
 PLT_DUO		.EQU	17		; DUODYNE Z80 SYSTEM
+PLT_HEATH	.EQU	18		; HEATHKIT H8 Z80 SYSTEM
 ;
 ; HBIOS GLOBAL ERROR RETURN VALUES
 ;
@@ -315,6 +316,7 @@ CIODEV_Z2U	.EQU	$A0
 CIODEV_LPT	.EQU	$B0
 CIODEV_ESPCON	.EQU	$C0
 CIODEV_ESPSER	.EQU	$D0
+CIODEV_SCON	.EQU	$E0
 ;
 ; SUB TYPES OF CHAR DEVICES
 ;
@@ -338,6 +340,8 @@ DIODEV_HDSK	.EQU	$90
 DIODEV_PPA	.EQU	$A0
 DIODEV_IMM	.EQU	$B0
 DIODEV_SYQ	.EQU	$C0
+DIODEV_CHUSB	.EQU	$D0
+DIODEV_CHSD	.EQU	$E0
 ;
 ; RTC DEVICE IDS
 ;
@@ -352,6 +356,7 @@ RTCDEV_RP5	.EQU	$50		; RP5C01
 ;
 DSKYDEV_ICM	.EQU	$00		; Intersil ICM7218
 DSKYDEV_PKD	.EQU	$10		; Intel P8279
+DSKYDEV_H8P	.EQU	$20		; Heath H8 Panel
 ;
 ; VIDEO DEVICE IDS
 ;
@@ -430,9 +435,9 @@ HCB_BIDUSR	.EQU	$D9		; USER BANK (TPA)
 HCB_BIDBIOS	.EQU	$DA		; BIOS BANK (HBIOS, UBIOS)
 HCB_BIDAUX	.EQU	$DB		; AUX BANK (BPBIOS)
 HCB_BIDRAMD0	.EQU	$DC		; FIRST BANK OF RAM DRIVE
-HCB_BIDRAMDN	.EQU	$DD		; LAST BANK OF RAM DRIVE
+HCB_RAMD_BNKS	.EQU	$DD		; RAM DRIVE BANK COUNT
 HCB_BIDROMD0	.EQU	$DE		; FIRST BANK OF ROM DRIVE
-HCB_BIDROMDN	.EQU	$DF		; LAST BANK OF ROM DRIVE
+HCB_ROMD_BNKS	.EQU	$DF		; ROM DRIVE BANK COUNT
 ;
 ; HBIOS PROXY COMMON DATA BLOCK
 ; EXACTLY 32 BYTES AT $FFE0-$FFFF
--- a/Source/HBIOS/hbios_env.asm
+++ b/Source/HBIOS/hbios_env.asm
@@ -24,7 +24,11 @@
 ;
 ; Print all desired config values...
 ;
+#if (ROMSIZE > 0)
 	prtval("ROMSIZE$", ROMSIZE)
+#else
+	prtval("ROMSIZE$", RAMSIZE)
+#endif
 	prtval("CPUFAM$", CPUFAM)
 ;
 	ret
--- a/Source/HBIOS/md.asm
+++ b/Source/HBIOS/md.asm
@@ -72,32 +72,30 @@ MD_INIT:
 ;
 #IF (MDROM)
 	PRTS(" ROMDISK=$")
-;	LD	HL,ROMSIZE - 128
-	LD	A,(HCB + HCB_ROMBANKS)	; GET NUMBER OF BANKS
-	SUB	(TOT_ROM_RB)
-	LD	L,A
-	LD	H,0			; CALCULATE RAM SIZE
+	LD	A,(CB_ROMD_BNKS)	; ROM DISK SIZE IN BANKS
+	LD	L,A			; PUT IN L
+	LD	H,0			; CALCULATE ROM DISK SIZE
 	ADD	HL,HL			; X2
 	ADD	HL,HL			; X4
 	ADD	HL,HL			; X8
 	ADD	HL,HL			; X16
 	ADD	HL,HL			; X32
+	LD	(MD_ROMDSIZE),HL	; SAVE ROM DISK SIZE
 	CALL	PRTDEC
 	PRTS("KB$")
 #ENDIF
 ;
 #IF (MDRAM)
 	PRTS(" RAMDISK=$")
-;	LD	HL,RAMSIZE - 256
-	LD	A,(HCB + HCB_RAMBANKS)	; GET NUMBER OF BANKS
-	SUB	(TOT_RAM_RB)		; LESS RESERVED BANKS
-	LD	L,A
-	LD	H,0			; CALCULATE RAM SIZE
+	LD	A,(CB_RAMD_BNKS)	; RAM DISK SIZE IN BANKS
+	LD	L,A			; PUT IN L
+	LD	H,0			; CALCULATE RAM DISK SIZE
 	ADD	HL,HL			; X2
 	ADD	HL,HL			; X4
 	ADD	HL,HL			; X8
 	ADD	HL,HL			; X16
 	ADD	HL,HL			; X32
+	LD	(MD_RAMDSIZE),HL	; SAVE RAM DISK SIZE
 	CALL	PRTDEC
 	PRTS("KB$")
 #ENDIF
@@ -183,21 +181,18 @@ MD_CAP:					; ASSUMES THAT UNIT 0 IS RAM, UNIT 1 IS ROM
 	SYSCHKERR(ERR_NOUNIT)		; INVALID UNIT
 	RET
 MD_CAP0:
-	LD	A,(HCB + HCB_RAMBANKS)	; POINT TO RAM BANK COUNT
-	LD	B,TOT_RAM_RB		; SET # RESERVED RAM BANKS
-	JR	MD_CAP2
+	; RAM DISK SIZE
+	LD	HL,(MD_RAMDSIZE)	; SIZE IN KB
+	JR	MD_CAP2			; CONTINUE
 MD_CAP1:
-	LD	A,(HCB + HCB_ROMBANKS)	; POINT TO ROM BANK COUNT
-	LD	B,TOT_ROM_RB		; SET # RESERVED ROM BANKS
+	; ROM DISK SIZE
+	LD	HL,(MD_ROMDSIZE)	; SIZE IN KB
 MD_CAP2:
-	SUB	B			; SUBTRACT OUT RESERVED BANKS
-	LD	H,A			; H := # BANKS
-	LD	E,64			; # 512 BYTE BLOCKS / BANK
-	CALL	MULT8			; HL := TOTAL # 512 BYTE BLOCKS
-	LD	DE,0			; NEVER EXCEEDS 64K, ZERO HIGH WORD
+	ADD	HL,HL			; CONVERT TO BLOCK COUNT
+	LD	DE,0			; FILL IN HIGH WORD
 	LD	BC,512			; 512 BYTE SECTOR
-	XOR	A
-	RET
+	XOR	A			; SIGNAL SUCCESS
+	RET				; DONE
 ;
 ;
 ;
@@ -1032,6 +1027,8 @@ MD_FFSEN	.DB	00h		; FLASH FILES SYSTEM ENABLE
 ;
 #ENDIF
 ;
+MD_ROMDSIZE	.DW	0
+MD_RAMDSIZE	.DW	0
 MD_RWFNADR	.DW	0
 MD_DSKBUF	.DW	0
 MD_SRCBNK	.DB	0
--- a/Source/HBIOS/pkd.asm
+++ b/Source/HBIOS/pkd.asm
@@ -371,7 +371,6 @@ PKD_KEYMAP:
 	; POS	$18  $19  $1A  $1B
 	; KEY   [F4] [F3] [F2] [F1]
 	.DB	$23, $22, $21, $20
-
 ;
 ;==================================================================================================
 ; PKD OUTPUT ROUTINES
--- a/Source/HBIOS/ppp.asm
+++ b/Source/HBIOS/ppp.asm
@@ -688,7 +688,7 @@ PPPSD_RESET:
 PPPSD_DEVICE:
 	LD	D,DIODEV_PPPSD		; D := DEVICE TYPE
 	LD	E,(IY+PPPSD_DEV)	; E := PHYSICAL DEVICE NUMBER
-	LD	C,%01110010		; C := ATTRIBUTES, REMOVABLE, SD CARD
+	LD	C,%00110010		; C := ATTRIBUTES, REMOVABLE, SD CARD
 	LD	H,0			; H := 0, DRIVER HAS NO MODES
 	LD	L,PPPBASE		; L := BASE I/O ADDRESS
 	XOR	A			; SIGNAL SUCCESS
--- a/Source/HBIOS/prp.asm
+++ b/Source/HBIOS/prp.asm
@@ -545,7 +545,7 @@ PRPSD_RESET:
 PRPSD_DEVICE:
 	LD	D,DIODEV_PRPSD		; D := DEVICE TYPE
 	LD	E,(IY+PRPSD_DEV)	; E := PHYSICAL DEVICE NUMBER
-	LD	C,%01110010		; C := ATTRIBUTES, REMOVABLE, SD CARD
+	LD	C,%00110010		; C := ATTRIBUTES, REMOVABLE, SD CARD
 	LD	H,0			; H := 0, DRIVER HAS NO MODES
 	LD	L,PRP_IOBASE		; L := BASE I/O ADDRESS
 	XOR	A			; SIGNAL SUCCESS
--- a/Source/HBIOS/romldr.asm
+++ b/Source/HBIOS/romldr.asm
@@ -140,7 +140,8 @@ start:
 	rst	08			; do it
 	ld	a,c			; previous bank to A
 	ld	(bid_ldr),a		; save previous bank for later
-	bit	7,a			; starting from ROM?
+	;;;bit	7,a			; starting from ROM?
+	cp	BID_IMG0		; ROM startup?
 #endif
 ;
 #if (BIOS == BIOS_UNA)
@@ -2189,7 +2190,9 @@ err:
 	ld	hl,str_err_prefix
 	call	pstr
 	pop	hl
-	jp	pstr
+	call	pstr
+	or	$ff			; signal error
+	ret				; done
 ;
 str_err_prefix	.db	bel,"\r\n\r\n*** ",0
 str_err_invcmd	.db	"Invalid command",0
--- a/Source/HBIOS/scon.asm
+++ b/Source/HBIOS/scon.asm
@@ -0,0 +1,126 @@
+;
+;==================================================================================================
+; S100 PROPELLER CONSOLE DRIVER
+;==================================================================================================
+;
+; TODO:
+;
+SCON_IOBASE	.EQU	$00
+;
+SCON_STATUS	.EQU	SCON_IOBASE
+SCON_DATA	.EQU	SCON_IOBASE + 1
+;
+SCON_KBDRDY	.EQU	%00000010
+SCON_DSPRDY	.EQU	%00000100
+;
+SCON_COLS	.EQU	80
+SCON_ROWS	.EQU	40
+;
+;
+;
+SCON_PREINIT:
+	XOR	A
+	RET
+;
+;
+;
+SCON_INIT:
+	CALL	NEWLINE
+	PRTS("SCON:$")
+;
+	; DISPLAY CONSOLE DIMENSIONS
+	CALL	PC_SPACE
+	LD	A,SCON_COLS
+	CALL	PRTDECB
+	LD	A,'X'
+	CALL	COUT
+	LD	A,SCON_ROWS
+	CALL	PRTDECB
+	CALL	PRTSTRD
+	.TEXT	" TEXT (ANSI)$"
+;
+; ADD OURSELVES TO CIO DISPATCH TABLE
+;
+	LD	D,0			; PHYSICAL UNIT IS ZERO
+	LD	E,CIODEV_SCON		; DEVICE TYPE
+	LD	BC,SCON_FNTBL		; BC := FUNCTION TABLE ADDRESS
+	CALL	CIO_ADDENT		; ADD ENTRY, A := UNIT ASSIGNED
+	LD	(HCB + HCB_CRTDEV),A	; SET OURSELVES AS THE CRT DEVICE
+;
+	XOR	A			; SIGNAL SUCCESS
+	RET
+;
+; DRIVER FUNCTION TABLE
+;
+SCON_FNTBL:
+	.DW	SCON_IN
+	.DW	SCON_OUT
+	.DW	SCON_IST
+	.DW	SCON_OST
+	.DW	SCON_INITDEV
+	.DW	SCON_QUERY
+	.DW	SCON_DEVICE
+#IF (($ - SCON_FNTBL) != (CIO_FNCNT * 2))
+	.ECHO	"*** INVALID SCON FUNCTION TABLE ***\n"
+#ENDIF
+;
+;
+;
+SCON_IN:
+	CALL	SCON_IST		; CHECK FOR CHAR PENDING
+	JR	Z,SCON_IN		; WAIT FOR IT IF NECESSARY
+	IN0	A,(SCON_DATA)		; READ THE CHAR FROM PROPIO
+	LD	E,A
+	RET
+;
+;
+;
+SCON_IST:
+	IN0	A,(SCON_STATUS)		; READ LINE STATUS REGISTER
+	AND	SCON_KBDRDY		; ISOLATE KBDRDY
+	JP	Z,CIO_IDLE		; RETURN VIA IDLE PROCESSING
+	OR	$FF			; SET A=$FF TO SIGNAL READY
+	RET				; RETURN
+;
+;
+;
+SCON_OUT:
+	CALL	SCON_OST		; CHECK FOR OUTPUT READY
+	JR	Z,SCON_OUT		; WAIT IF NECESSARY
+	LD	A,E			; RECOVER THE CHAR TO WRITE
+	OUT0	(SCON_DATA),A		; WRITE THE CHAR TO PROPIO
+	RET
+;
+;
+;
+SCON_OST:
+	IN0	A,(SCON_STATUS)		; READ LINE STATUS REGISTER
+	AND	SCON_DSPRDY 		; ISOLATE DSPRDY
+	JP	Z,CIO_IDLE		; RETURN VIA IDLE PROCESSING
+	OR	$FF			; SET A=$FF TO SIGNAL READY
+	RET				; RETURN
+;
+;
+;
+SCON_INITDEV:
+	SYSCHKERR(ERR_NOTIMPL)
+	RET
+;
+;
+;
+SCON_QUERY:
+	LD	DE,0
+	LD	HL,0
+	XOR	A
+	RET
+;
+;
+;
+SCON_DEVICE:
+	LD	D,CIODEV_SCON		; D := DEVICE TYPE
+	LD	E,0			; E := DEVICE NUM, ALWAYS 0
+	LD	C,$BF			; C := DEVICE TYPE, 0xBF IS PROP TERM
+	LD	H,0			; H := 0, DRIVER HAS NO MODES
+	LD	L,SCON_IOBASE		; L := BASE I/O ADDRESS
+	XOR	A			; SIGNAL SUCCESS
+	RET
--- a/Source/HBIOS/sd.asm
+++ b/Source/HBIOS/sd.asm
@@ -932,7 +932,7 @@ SD_RESET:
 SD_DEVICE:
 	LD	D,DIODEV_SD		; D := DEVICE TYPE
 	LD	E,(IY+SD_DEV)		; E := PHYSICAL DEVICE NUMBER
-	LD	C,%01110010		; C := ATTRIBUTES, REMOVABLE, SD CARD
+	LD	C,%00110010		; C := ATTRIBUTES, REMOVABLE, SD CARD
 	LD	H,SDMODE		; H := MODE
 	LD	L,(SD_IOBASE)		; L := BASE I/O ADDRESS
 	XOR	A			; SIGNAL SUCCESS
--- a/Source/HBIOS/std.asm
+++ b/Source/HBIOS/std.asm
@@ -566,10 +566,8 @@ SYSTIM	.SET	TM_Z280
 ;
 ; MEMORY BANK CONFIGURATION
 ;
-WBW_ROM_R	.EQU	128	; 128K			; RESERVED ROM REQUIRED FOR ROMWBW
-WBW_RAM_R	.EQU	256	; 256K			; RESERVED RAM REQUIRED FOR ROMWBW
-TOT_ROM_RB	.EQU	(WBW_ROM_R / 32)		; TOTAL ROM BANKS RESERVED
-TOT_RAM_RB	.EQU	(WBW_RAM_R / 32)		; TOTAL RAM BANKS RESERVED
+ROMBANKS	.EQU	(ROMSIZE / 32)			; TOTAL ROM BANKS
+RAMBANKS	.EQU	(RAMSIZE / 32)			; TOTAL RAM BANKS
 ;
 #IF (BIOS == BIOS_UNA)
 BID_ROM0	.EQU	$0000
@@ -580,26 +578,45 @@ BID_RAM0	.EQU	$8000
 BID_ROM0	.EQU	$00
 BID_RAM0	.EQU	$80
 #ENDIF
-
-BID_ROMN	.EQU	(BID_ROM0 + ((ROMSIZE / 32) - 1))
-BID_RAMN	.EQU	(BID_RAM0 + ((RAMSIZE / 32) - 1))
 ;
-BID_RAMD0	.EQU	BID_RAM0	; FIRST RAM DRIVE BANK			 ^  RAM
-BID_RAMDN	.EQU	BID_RAMN - TOT_RAM_RB	; LAST RAM DRIVE BANK		 |  DRIVE
-;					; OS BUFFERS CP/M3?			-+ THESE	CPM3 BNK 5 (BUF)
-;					; OS BUFFERS CP/M3?			 | MAKE		CPM3 BNK 4 (BUF)
-;					; OS BUFFERS CP/M3?			 | UP		CPM3 BNK 3 (BUF)
-;					; OS BUFFERS CP/M3?			 | THE		CPM3 BNK 2 (BUF)
-BID_AUX		.EQU	BID_RAMN - 3	; AUX BANK (BPBIOS, ETC.)		 | 256KB	CPM3 BNK 1 (TPA)
-BID_BIOS	.EQU	BID_RAMN - 2	; BIOS BANK				 | RESERVED
-BID_USR		.EQU	BID_RAMN - 1	; USER BANK (CP/M TPA, ETC.)		 | RAM		CPM3 BNK 0 (OS)
-BID_COM		.EQU	BID_RAMN - 0	; COMMON BANK, UPPER 32K		-+ BANKS
-BID_BOOT	.EQU	BID_ROM0 + 0	; BOOT BANK				-+ THESE MAKE
-BID_IMG0	.EQU	BID_ROM0 + 1	; ROM LOADER AND FIRST IMAGES BANK	 | UP THE 128KB
-BID_IMG1	.EQU	BID_ROM0 + 2	; SECOND IMAGES BANK		 	 | RESERVED
-BID_IMG2	.EQU	BID_ROM0 + 3	; NETWORK BOOT				-+ ROM BANKS
-BID_ROMD0	.EQU	BID_ROM0 + 4	; FIRST ROM DRIVE BANK			 |  ROM
-BID_ROMDN	.EQU	BID_ROMN	; LAST ROM DRIVE BANK			 V  DRIVE
+BID_ROMN	.EQU	(BID_ROM0 + ROMBANKS - 1)
+BID_RAMN	.EQU	(BID_RAM0 + RAMBANKS - 1)
+;
+#IF (ROMSIZE > 0)
+;										-- TYPICAL --
+BID_BOOT	.EQU	BID_ROM0 + 0	; BOOT BANK				0x00
+BID_IMG0	.EQU	BID_ROM0 + 1	; ROM LOADER AND FIRST IMAGES BANK	0x01
+BID_IMG1	.EQU	BID_ROM0 + 2	; SECOND IMAGES BANK		 	0x02
+BID_IMG2	.EQU	BID_ROM0 + 3	; RESERVED				0x03
+BID_ROMD0	.EQU	BID_ROM0 + 4	; FIRST ROM DRIVE BANK			0x04
+BID_ROMDN	.EQU	BID_ROMN	; LAST ROM DRIVE BANK			0x0F
+;
+BID_BIOS	.EQU	BID_RAM0	; HBIOS BANK				0x80
+BID_RAMD0	.EQU	BID_RAM0 + 1	; FIRST RAM DRIVE BANK			0x81
+BID_RAMDN	.EQU	BID_RAMN - 4	; LAST RAM DRIVE BANK			0x8B
+BID_BUF		.EQU	BID_RAMN - 3	; OS BUFFERS (CP/M3)			0x8C
+BID_AUX		.EQU	BID_RAMN - 2	; AUX BANK (CP/M 3, BPBIOS, ETC.)	0x8D
+BID_USR		.EQU	BID_RAMN - 1	; USER BANK (CP/M TPA, ETC.)		0x8E
+BID_COM		.EQU	BID_RAMN - 0	; COMMON BANK, UPPER 32K		0x8F
+;
+#ELSE
+;										-- TYPICAL --
+BID_BOOT	.EQU	BID_RAM0 + 0	; BOOT BANK				0x80
+BID_IMG0	.EQU	BID_RAM0 + 1	; ROM LOADER AND FIRST IMAGES BANK	0x81
+BID_IMG1	.EQU	BID_RAM0 + 2	; SECOND IMAGES BANK		 	0x82
+BID_IMG2	.EQU	BID_RAM0 + 3	; RESERVED				0x83
+BID_RAMD0	.EQU	BID_RAM0 + 4	; FIRST RAM DRIVE BANK			0x84
+BID_RAMDN	.EQU	BID_RAMN - 4	; LAST RAM DRIVE BANK			0x8B
+BID_BUF		.EQU	BID_RAMN - 3	; OS BUFFERS (CP/M3)			0x8C
+BID_AUX		.EQU	BID_RAMN - 2	; AUX BANK (CP/M 3, BPBIOS, ETC.)	0x8D
+BID_USR		.EQU	BID_RAMN - 1	; USER BANK (CP/M TPA, ETC.)		0x8E
+BID_COM		.EQU	BID_RAMN - 0	; COMMON BANK, UPPER 32K		0x8F
+;
+BID_BIOS	.EQU	BID_BOOT	; HBIOS BANK				0x80
+BID_ROMD0	.EQU	0		; NO ROM DRIVE
+BID_ROMDN	.EQU	$FF		; NO ROM DRIVE
+;
+#ENDIF
 ;
 #IF (ROMSIZE == 0)
 BID_BOOT	.SET	BID_RAM0	; SPECIAL CASE ROM-LESS SYSTEM
@@ -609,17 +626,21 @@ BID_BOOT	.SET	BID_RAM0	; SPECIAL CASE ROM-LESS SYSTEM
 ;
  #IF (!MDRAM)
 BID_RAMD0	.SET	$FF		; RAM DRIVE DISABLED
-BID_RAMDN	.SET	$FF		; RAM DRIVE DISABLED
+BID_RAMDN	.SET	0		; RAM DRIVE DISABLED
  #ENDIF
 ;
  #IF (!MDROM)
 BID_ROMD0	.SET	$FF		; ROM DRIVE DISABLED
-BID_ROMDN	.SET	$FF		; ROM DRIVE DISABLED
+BID_ROMDN	.SET	0		; ROM DRIVE DISABLED
  #ENDIF
 ;
+ROMD_BNKS	.EQU	(BID_ROMDN - BID_ROMD0 + 1)
+RAMD_BNKS	.EQU	(BID_RAMDN - BID_RAMD0 + 1)
+;
 #ENDIF
 ;
-#IF FALSE
+#IF TRUE
+	.ECHO "BID_BUF: " \ .ECHO BID_BUF \ .ECHO "\n"
 	.ECHO "BID_AUX: " \ .ECHO BID_AUX \ .ECHO "\n"
 	.ECHO "BID_BIOS: " \ .ECHO BID_BIOS \ .ECHO "\n"
 	.ECHO "BID_USR: " \ .ECHO BID_USR \ .ECHO "\n"
--- a/Source/Images/Build.cmd
+++ b/Source/Images/Build.cmd
@@ -13,7 +13,7 @@ call BuildDisk.cmd nzcom fd wbw_fd144 ..\zsdos\zsys_wbw.sys || exit /b
 call BuildDisk.cmd cpm3 fd wbw_fd144 ..\cpm3\cpmldr.sys || exit /b
 call BuildDisk.cmd zpm3 fd wbw_fd144 ..\zpm3\zpmldr.sys || exit /b
 call BuildDisk.cmd ws4 fd wbw_fd144 || exit /b
-call BuildDisk.cmd qpm fd wbw_fd144 d_qpm\u0\qpm.sys || exit /b
+call BuildDisk.cmd qpm fd wbw_fd144 ..\qpm\qpm_wbw.sys || exit /b
 call BuildDisk.cmd z80asm hd wbw_fd144 || exit /b
 call BuildDisk.cmd aztecc hd wbw_fd144 || exit /b
 call BuildDisk.cmd hitechc hd wbw_fd144 || exit /b
@@ -25,6 +25,7 @@ call BuildDisk.cmd games hd wbw_fd144 || exit /b
 echo.
 echo Building Hard Disk Images (512 directory entry format)...
 echo.
+call BuildDisk.cmd blank hd wbw_hd512 || exit /b
 call BuildDisk.cmd cpm22 hd wbw_hd512 ..\cpm22\cpm_wbw.sys || exit /b
 call BuildDisk.cmd zsdos hd wbw_hd512 ..\zsdos\zsys_wbw.sys || exit /b
 call BuildDisk.cmd nzcom hd wbw_hd512 ..\zsdos\zsys_wbw.sys || exit /b
@@ -32,7 +33,7 @@ call BuildDisk.cmd cpm3 hd wbw_hd512 ..\cpm3\cpmldr.sys || exit /b
 call BuildDisk.cmd zpm3 hd wbw_hd512 ..\zpm3\zpmldr.sys || exit /b
 call BuildDisk.cmd ws4 hd wbw_hd512 || exit /b
 call BuildDisk.cmd dos65 hd wbw_hd512 ..\zsdos\zsys_wbw.sys || exit /b
-call BuildDisk.cmd qpm hd wbw_hd512 d_qpm\u0\qpm.sys || exit /b
+call BuildDisk.cmd qpm hd wbw_hd512 ..\qpm\qpm_wbw.sys || exit /b
 call BuildDisk.cmd z80asm hd wbw_hd512 || exit /b
 call BuildDisk.cmd aztecc hd wbw_hd512 || exit /b
 call BuildDisk.cmd hitechc hd wbw_hd512 || exit /b
@@ -50,13 +51,14 @@ copy /b ..\..\Binary\hd512_cpm22.img + ..\..\Binary\hd512_zsdos.img + ..\..\Bina
 echo.
 echo Building Hard Disk Images (1024 directory entry format)...
 echo.
+call BuildDisk.cmd blank hd wbw_hd1k || exit /b
 call BuildDisk.cmd cpm22 hd wbw_hd1k ..\cpm22\cpm_wbw.sys || exit /b
 call BuildDisk.cmd zsdos hd wbw_hd1k ..\zsdos\zsys_wbw.sys || exit /b
 call BuildDisk.cmd nzcom hd wbw_hd1k ..\zsdos\zsys_wbw.sys || exit /b
 call BuildDisk.cmd cpm3 hd wbw_hd1k ..\cpm3\cpmldr.sys || exit /b
 call BuildDisk.cmd zpm3 hd wbw_hd1k ..\zpm3\zpmldr.sys || exit /b
 call BuildDisk.cmd ws4 hd wbw_hd1k || exit /b
-call BuildDisk.cmd qpm hd wbw_hd1k d_qpm\u0\qpm.sys || exit /b
+call BuildDisk.cmd qpm hd wbw_hd1k ..\qpm\qpm_wbw.sys || exit /b
 call BuildDisk.cmd z80asm hd wbw_hd1k || exit /b
 call BuildDisk.cmd aztecc hd wbw_hd1k || exit /b
 call BuildDisk.cmd hitechc hd wbw_hd1k || exit /b
--- a/Source/Images/Makefile
+++ b/Source/Images/Makefile
@@ -1,7 +1,7 @@
 #
 # this makefile subsumes all the work done in Build.cmd, BuildDisk.cmd, BuildDisk.ps1
 #
-SYSTEMS = ../CPM22/cpm_wbw.sys ../ZSDOS/zsys_wbw.sys ../CPM3/cpmldr.sys ../ZPM3/zpmldr.sys
+SYSTEMS = ../CPM22/cpm_wbw.sys ../ZSDOS/zsys_wbw.sys ../QPM/qpm_wbw.sys ../CPM3/cpmldr.sys ../ZPM3/zpmldr.sys

 FDIMGS = fd144_cpm22.img fd144_zsdos.img fd144_nzcom.img \
 	fd144_cpm3.img fd144_zpm3.img fd144_ws4.img fd144_qpm.img \
@@ -12,13 +12,13 @@ HD512IMGS = hd512_cpm22.img hd512_zsdos.img hd512_nzcom.img \
 	hd512_cpm3.img hd512_zpm3.img hd512_ws4.img
 HD512XIMGS = hd512_z80asm.img hd512_aztecc.img hd512_hitechc.img \
 	hd512_bascomp.img hd512_fortran.img hd512_games.img \
-	hd512_tpascal.img hd512_dos65.img hd512_qpm.img
+	hd512_tpascal.img hd512_dos65.img hd512_qpm.img hd512_blank.img
 # HDIMGS += hd512_bp.img
 HD1KIMGS = hd1k_cpm22.img hd1k_zsdos.img hd1k_nzcom.img \
 	hd1k_cpm3.img hd1k_zpm3.img hd1k_ws4.img
 HD1KXIMGS = hd1k_z80asm.img hd1k_aztecc.img hd1k_hitechc.img \
 	hd1k_bascomp.img hd1k_fortran.img hd1k_games.img \
-	hd1k_tpascal.img hd1k_qpm.img
+	hd1k_tpascal.img hd1k_qpm.img hd1k_blank.img
 # HD1KIMGS += hd1k_bp.img

 HD512PREFIX =
@@ -80,7 +80,7 @@ blankhd1k:
 	@sys= ; \
 	case $@ in \
 		(*cpm22*) sys=../CPM22/cpm_wbw.sys;; \
-		(*qpm*) sys=d_qpm/u0/qpm.sys;; \
+		(*qpm*) sys=../QPM/qpm_wbw.sys;; \
 		(*zsdos* | *nzcom* | *dos65*) sys=../ZSDOS/zsys_wbw.sys;; \
 		(*cpm3*) sys=../CPM3/cpmldr.sys;; \
 		(*zpm3*) sys=../ZPM3/zpmldr.sys;; \
--- a/Source/Images/d_blank/ReadMe.txt
+++ b/Source/Images/d_blank/ReadMe.txt
@@ -0,0 +1,6 @@
+===== Blank Disk for RomWBW =====
+
+This disk is intentionally empty and just provides an empty slice
+that can be used in the concatenation of slices as desired
+
+-- WBW 3:59 PM 10/4/2023
--- a/Source/Images/d_qpm/ReadMe.txt
+++ b/Source/Images/d_qpm/ReadMe.txt
@@ -36,11 +36,19 @@ code brakpoints.  This conflicts the use of that vector for any
 system that is using interrupt mode 1.  DEBUGZ can be configured
 (using DBGINST) to use a different vector.

-The QSTAMP program, which is used to initialize a disk for date/time
-stamping, misbehavews when run on the (new) RomWBW 1024 directory
-format disks.  It creates an invalid directory entry for the
-date/time stamp data file.  This is definitely a QP/M issue.  The
-directory entry can be manually corrected.
+The QSTAMP program, which is used to initialize a disk for date/time 
+stamping, misbehavews when run on the (new) RomWBW 1024 directory 
+format disks.  It creates an invalid directory entry for the date/time 
+stamp data file.  This is definitely a QP/M issue.  The directory entry 
+can be manually corrected.  Specifically the byte offset 15 should 
+contain the number of 128-byte records in the file.  Instead, it is set 
+to 0x01.  You can edit the entry, change it to 0x80 and everything
+starts working.
+
+There are two text files (QPMCMDS.TXT and QPMUTILS.TXT) included.  They
+came from the original QP/M 2.7 distribution.  These files have
+escape sequences imbedded in them which makes them look a little
+strange depending on the terminal emulation you are using.

 == QPM 2.7 Files ==

@@ -48,10 +56,9 @@ The following files came from the official QP/M distribution.  Actually,
 they came from 3 Microcode Consulting files (qpm27.zip, debugz.zip,
 and linkz.zip).  The original distribution files can be found on the
 Microcode Consulting website at https://www.microcodeconsulting.com/.
-Documentation (pdf) files are incuded in these original distribution
-.zip files.  These documentation files have not been included in the
-RomWBW distribution.  Please retrieve them yourself from the website
-if desired.
+Documentation (pdf) files are included in these original distribution
+.zip files.  These documentation files have been included in the
+RomWBW distribution in the Doc folder.

 D.COM - Directory lister
 DBGINST.COM - Configures DEBUGZ debugger
--- a/Source/Images/d_qpm/u0/qpm.sys
+++ b/Source/Images/d_qpm/u0/qpm.sys
--- a/Source/Images/diskdefs
+++ b/Source/Images/diskdefs
@@ -310,6 +310,32 @@ diskdef wbw_rom1024
  os 2.2
 end

+# RomWBW 512KB RAM (256KB reserved, 256KB RAM Disk)
+
+diskdef wbw_ram512
+  seclen 512
+  tracks 8
+  sectrk 64
+  blocksize 2048
+  maxdir 256
+  skew 0
+  boottrk 0
+  os 2.2
+end
+
+# RomWBW 1024KB RAM (256KB reserved, 768KB RAM Disk)
+
+diskdef wbw_ram1024
+  seclen 512
+  tracks 24
+  sectrk 64
+  blocksize 2048
+  maxdir 256
+  skew 0
+  boottrk 0
+  os 2.2
+end
+
 # RomWBW 720K floppy media

 diskdef wbw_fd720
--- a/Source/Images/fd_qpm.txt
+++ b/Source/Images/fd_qpm.txt
@@ -44,7 +44,7 @@ d_cpm22/u0/*.* 0:
 #
 # Add OS image
 #
-../CPM22/cpm_wbw.sys 0:cpm.sys
+../QPM/qpm_wbw.sys 0:qpm.sys
 #
 # Add Common Applications
 #
--- a/Source/Images/hd_blank.txt
+++ b/Source/Images/hd_blank.txt
@@ -0,0 +1,3 @@
+#
+# Blank disk template
+#
--- a/Source/Images/hd_qpm.txt
+++ b/Source/Images/hd_qpm.txt
@@ -51,7 +51,7 @@ cpnet12/*.* 4:
 #
 # Add OS image
 #
-../CPM22/cpm_wbw.sys 0:cpm.sys
+../QPM/qpm_wbw.sys 0:qpm.sys
 #
 # Add Common Applications
 #
--- a/Show More
+++ b/Show More
Author	SHA1	Message	Date
Wayne Warthen	c1fa7b420a	SD Media Automatic Drive Assignment - Issue #365 - Modified SD Media handling such that no OS drive letters will be assigned automatically at OS Startup if there is no media inserted.	2023-10-05 10:14:30 -07:00
Wayne Warthen	9072bc6d70	Issue #366 Based on input from Dean Jenkins: - Updated User Guide to clarify some nuances related to use of Combo Disk Images - Added "blank" slice images	2023-10-04 16:54:34 -07:00
Wayne Warthen	480dbe4f4c	Add Disk Images for ROMless Configurations	2023-10-03 19:44:49 -07:00
Wayne Warthen	26fad23c3a	Z280 ROMless Fixes - Corrected a couple deficiencies that caused Z280 CPUs to fail in the new ROMless configuration	2023-10-03 15:24:18 -07:00
Wayne Warthen	883dab7e97	ROMless Operation Overhaul - Implement new approach to ROMless boot and operation. Still missing the ability to seed the RAM disk. - Tweaks to CH driver	2023-10-01 17:22:19 -07:00
Wayne Warthen	d3f5643791	CH Driver Tweaks	2023-09-24 16:47:36 -07:00
Wayne Warthen	5299d24379	Merge pull request #363 from skullandbones/Issue-362_RPI4_no_bios.bin_v1 zxcc: Fix for load bios.bin failure on a RPi4	2023-09-24 16:25:50 -07:00
Dean Jenkins	a229db96a6	zxcc: Fix for load bios.bin failure on a RPi4 Fix load_bios() when used on a Raspberry Pi4. The defect was corrupting the path of the zxcc executable. The fix is to NUL terminate the path string from the readlink() call.	2023-09-24 17:04:35 +01:00
Wayne Warthen	092e44c62e	RPi Builds & CH375/6 Support - The build process was enhanced by Dean Jenkins to support the Raspberry Pi. Note that the Propeller firmware will not be generated by a RPi build. See Issue #358. - Initial support for USB storage via CH375/6.	2023-09-22 14:13:12 -07:00
Wayne Warthen	722bce819b	Bump Version	2023-09-16 13:41:32 -07:00
Wayne Warthen	2d470a2a90	Merge pull request #360 from danwerner21/dev ESP32 Driver updates	2023-09-16 13:24:08 -07:00
Dan Werner	b6700dfa4c	ESP32 Driver updates	2023-09-16 14:47:09 -05:00
Wayne Warthen	cfc76d0659	Add Heath H8 Framework	2023-09-14 19:38:17 -07:00
Wayne Warthen	7fce3277a0	Create SCZ180_sc700.asm - Missed this file on last commit	2023-09-13 14:56:24 -07:00
Wayne Warthen	2219e4c82d	Miscellaneous - Add SCZ180_sc700 standard build - Minor fix to DMAMON	2023-09-13 14:03:54 -07:00
Wayne Warthen	68e841e62c	Miscellaneous - Minor correction to DMAMON to restore proper operation of interrupt testing - Minor improvements to QPM documentation	2023-09-11 10:17:57 -07:00
Wayne Warthen	bb70c36b36	Improve QPM Build The QPM portion of the build has been updated to dynamically combine the current CBIOS with the static QPM CCP and BDOS binaries. This will keep the QPM system image up to date and avoid HBIOS version mismatch warnings.	2023-09-09 16:18:40 -07:00
Wayne Warthen	c391fd6d56	Support S100 Propeller Console	2023-09-07 18:16:25 -07:00
Wayne Warthen	e69caf5059	Add SROM (Serial ROM) Utility	2023-09-05 16:29:05 -07:00
Wayne Warthen	8b7e71049b	FDC Detection Update & Enable ESP Driver on Duodyne - Based on reports from Martin R, the FDC detection algorithm has been updated to try reading the FDC MSR register twice to try and get the desired value of 0x80. - Dan Werner's ESP board for Duodyne is working well, so the default Duodyne config has been changed to automatically detect this board.	2023-08-25 10:25:07 -07:00
Wayne Warthen	50e190c755	Merge pull request #357 from fernandocarolo/dev Fix references to the EPFDC driver in comments.	2023-08-23 14:44:47 -07:00
Wayne Warthen	d0eccf026b	Enable INTRTC for Easy Z80	2023-08-23 14:28:20 -07:00
Fernando Carolo	39f796ce22	Fix references to the EPFDC driver in comments. The EtchedPixels floppy disk controller is known by the identifier 'FDMODE_EPFDC', but the comments in the Config subdirectory have an incorrect reference to 'EPWDC'. This fix updates the comments to use the correct name.	2023-08-23 21:02:48 +01:00
Wayne Warthen	5610e79db4	Improve FD Driver Detection Credit to Martin R for reporting that his FDC was not being detected. The delay between FDC status register reads was increased in the detection routine to correct this.	2023-08-22 15:22:11 -07:00