Merge pull request #422 from wwarthen/work

Config File Cleanup

Binary/Apps/Test/inttest.doc

@@ -0,0 +1,44 @@
+INTTEST
+=======
+
+RomWBW includes an API allowing applications to "hook" interrupts.
+The `INTTEST` utility allows you to test this functionality.
+
+
+** Syntax **
+
+`INTTEST`
+
+
+** Usage **
+
+`INTTEST` is an interactive application.  At startup, it will display
+a list of the interrupt vector slots in your system along with the
+current vector address for each of them.
+
+It then prompts you to enter the slot number (in hex) of a vector to
+hook.  After entering this, the application will watch the hooked
+vector and countdown from 0xFF to 0x00 as interrupts are noted.
+
+When the counter reaches 0x00, the interrupt is unhooked and the
+application terminates.  The application can also be terminated by
+pressing <esc>.
+
+
+** Notes **
+
+If your system is running without interrupts active, the application
+will terminate immediately.
+
+All slots have vectors even if the corresponding interrupt is not
+doing anything.  In this case, the vector is pointing to the "bad
+interrupt" handler.
+
+If you hook a vector that is not receiving any interrupts, the
+down-counter will not do anything.
+
+
+** Etymology* *
+
+The `INTTEST` command is an original product and the source code is
+provided in the RomWBW distribution.

Binary/ReadMe.txt

@@ -6,37 +6,37 @@
 ***                                                                 ***
 ***********************************************************************
 
-This directory ("Binary") is part of the RomWBW System Software 
-distribution archive.  It contains the completed binary outputs of 
-the build process.  As described below, these files are used to 
+This directory ("Binary") is part of the RomWBW System Software
+distribution archive.  It contains the completed binary outputs of
+the build process.  As described below, these files are used to
 assemble a working RetroBrew Computers system.
 
-The files in this directory are created by the build process that is 
-documented in the ReadMe.txt file in the Source directory.  When 
-released the directory is populated with the default output files.  
-However, the output of custom builds will be placed in this directory 
+The files in this directory are created by the build process that is
+documented in the ReadMe.txt file in the Source directory.  When
+released the directory is populated with the default output files.
+However, the output of custom builds will be placed in this directory
 as well.
 
-If you only see a few files in this directory, then you downloaded 
-just the source from GitHub.  To retrieve the full release download 
-package, go to https://github.com/wwarthen/RomWBW.  On this page, 
-look for the text "XX releases" where XX is a number. Click on this 
-text to go to the releases page.  On this page, you will see the 
-latest releases listed.  For each release, you will see a package 
-file called something like "RomWBW-2.9.0-Package.zip".  Click on the 
+If you only see a few files in this directory, then you downloaded
+just the source from GitHub.  To retrieve the full release download
+package, go to https://github.com/wwarthen/RomWBW.  On this page,
+look for the text "XX releases" where XX is a number. Click on this
+text to go to the releases page.  On this page, you will see the
+latest releases listed.  For each release, you will see a package
+file called something like "RomWBW-2.9.0-Package.zip".  Click on the
 package file for the release you want to download.
 
 ROM Firmware Images (<plt>_<cfg>.rom)
 -------------------------------------
 
-The files with a ".rom" extension are binary images ready to program 
-into an appropriate PROM.  These files are named with the format 
-<plt>_<cfg>.rom. <plt> refers to the primary platform such as Zeta, 
-N8, Mark IV, etc.  <cfg> refers to the specific configuration.  In 
-general, there will be a standard configuration ("std") for each 
-platform.  So, for example, the file called MK4_std.rom is a ROM 
-image for the Mark IV with the standard configuration. If a custom 
-configuration called "custom" is created and built, a new file called 
+The files with a ".rom" extension are binary images ready to program
+into an appropriate PROM.  These files are named with the format
+<plt>_<cfg>.rom. <plt> refers to the primary platform such as Zeta,
+N8, Mark IV, etc.  <cfg> refers to the specific configuration.  In
+general, there will be a standard configuration ("std") for each
+platform.  So, for example, the file called MK4_std.rom is a ROM
+image for the Mark IV with the standard configuration. If a custom
+configuration called "custom" is created and built, a new file called
 MK4_custom.rom will be added to this directory.
 
 Documentation of the pre-built ROM Images is contained in
@@ -54,52 +54,52 @@ contents.  Refer to the RomWBW User Guide for more information.
 ROM Executable Images (<plt>_<cfg>.com)
 ---------------------------------------
 
-When a ROM image (".rom") is created, an executable version of the 
-ROM is also created.  These files have the same naming convention as 
-the ROM Image files, but have the extension ".com".  These files can 
+When a ROM image (".rom") is created, an executable version of the
+ROM is also created.  These files have the same naming convention as
+the ROM Image files, but have the extension ".com".  These files can
 be copied to a working system and run like a normal CP/M application.
 
-When run on the target system, they install in RAM just like they had 
+When run on the target system, they install in RAM just like they had
 been loaded from  ROM.  This allows a new ROM build to be tested
 without reprogramming the actual ROM.
 
-WARNING: In a few cases the .com file is too big to load.  If you get 
-a message like "Full" or "BAD LOAD" when trying to load one of the 
-.com files, it is too big.  In these cases, you will not be able to 
+WARNING: In a few cases the .com file is too big to load.  If you get
+a message like "Full" or "BAD LOAD" when trying to load one of the
+.com files, it is too big.  In these cases, you will not be able to
 test the ROM prior to programming it.
 
 VDU ROM Image (vdu.rom)
 -----------------------
 
-The VDU video board requires a dedicated onboard ROM containing the 
-font data.  The "vdu.rom" file contains the binary data to program 
+The VDU video board requires a dedicated onboard ROM containing the
+font data.  The "vdu.rom" file contains the binary data to program
 onto that chip.
 
-Disk Images (fd_*.img, hd_*.img, psys.img)
-------------------------------------------
+Disk Images (fd_*.img, hd_*.img)
+--------------------------------
 
-RomWBW includes a mechanism for generating floppy disk and hard disk 
-binary images that are ready to copy directly to a floppy, hard disk, 
-CF Card, or SD Card which will then be ready for use in any 
+RomWBW includes a mechanism for generating floppy disk and hard disk
+binary images that are ready to copy directly to a floppy, hard disk,
+CF Card, or SD Card which will then be ready for use in any
 RomWBW-based system.
 
-Essentially, these files contain prepared floppy and hard disk images 
-with a large set of programs and related files.  By copying the 
-contents of these files to appropriate media as described below, you 
+Essentially, these files contain prepared floppy and hard disk images
+with a large set of programs and related files.  By copying the
+contents of these files to appropriate media as described below, you
 can quickly create ready-to-use media.  Win32DiskImager or
 RawWriteWin can be used to copy images directly to media.  These
 programs are included in the RomWBW Tools directory.
 
-The fd_*.img files are floppy disk images.  They are sized for 1.44MB 
-floppy media and can be copied to actual floppy disks using 
-RawWriteWin (as long as you have access to a floppy drive on your 
-Windows computer).  The resulting floppy disks will be usable on any 
+The fd_*.img files are floppy disk images.  They are sized for 1.44MB
+floppy media and can be copied to actual floppy disks using
+RawWriteWin (as long as you have access to a floppy drive on your
+Windows computer).  The resulting floppy disks will be usable on any
 RomWBW-based system with floppy drive(s).
 
-Likewise, the hd512_*.img and hd1k_*.img files are hard disk images.  
-Each file is intended to be copied to the start of any type of hard 
-disk media (typically a CF Card or SD Card). The resulting media will 
-be usable on any RomWBW-based system that accepts the corresponding 
+Likewise, the hd512_*.img and hd1k_*.img files are hard disk images.
+Each file is intended to be copied to the start of any type of hard
+disk media (typically a CF Card or SD Card). The resulting media will
+be usable on any RomWBW-based system that accepts the corresponding
 media type.
 
 NOTE: The hd512_*.img files are equivalent to the hd_*.img
@@ -109,34 +109,58 @@ maximum number of CP/M directory entries from 512 to 1024.
 Refer to the ReadMe.txt in the Source/Images directory
 for details.
 
-Documentation of the pre-built disk images is contained in the 
+Documentation of the pre-built disk images is contained in the
 "RomWBW User Guide" found in the Doc directory.  The contents of
 the disk images is contained in the "RomWBW Disk Catalog", but it
 is significantly out-of-date.
 
-The contents of the floppy/hard disk images are created by 
-the BuildImages.cmd script in the Source directory.  Additional 
-information on how to generate custom disk images is found in the 
+The contents of the floppy/hard disk images are created by
+the BuildImages.cmd script in the Source directory.  Additional
+information on how to generate custom disk images is found in the
 Source\Images ReadMe.txt file.
 
-The psys.img file contains a full implementation of the UCSD p-System 
-for the Z80 running under RomWBW.  This image file must be placed on 
-disk media by itself (not appended or concatenated with hd*.img files.  
-Refer to the Source/pSys/ReadMe.txt file for more information on the 
+Disk Images (hd512_combo.img, hd1k_combo.img, *_std_hd1k_combo.img)
+-------------------------------------------------------------------
+
+The hd512_combo.img and hd1k_combo.img file are the primary combo
+disk image files suitable for most platforms.
+
+The *_std_hd1k_combo.img files are platform specific combo files
+typically used in romless platforms, they also contain RomWBW binary code
+that is loaded at boot time into RAM
+
+Disk Images (hd1k_prefix.dat, *_std_hd1k_prefix.dat)
+----------------------------------------------------
+
+The hd1k_prefix.dat file is part of the combo disk images and is
+applied to hd1k image files as a prefix, it contains the standard
+partion table.
+
+The *_std_hd1k_prefix.dat files are platform specific prefixes
+typically used in romless platforms, they also contain RomWBW binary code
+that is loaded at boot time into RAM
+
+Disk Images (psys.img)
+----------------------
+
+The psys.img file contains a full implementation of the UCSD p-System
+for the Z80 running under RomWBW.  This image file must be placed on
+disk media by itself (not appended or concatenated with hd*.img files.
+Refer to the Source/pSys/ReadMe.txt file for more information on the
 p-System implementation.
 
 Propeller ROM Images (*.eeprom)
 -------------------------------
 
-The files with and extension of ".eeprom" contain the binary images 
-to be programmed into the Propeller-based boards.  The list below 
+The files with and extension of ".eeprom" contain the binary images
+to be programmed into the Propeller-based boards.  The list below
 indicates which file targets each of the Propeller board variants:
 
 	ParPortProp	ParPortProp.eeprom
 	PropIO V1	PropIO.eeprom
 	PropIO V2	PropIO2.eeprom
 
-Refer to the board documentation of the boards for more information 
+Refer to the board documentation of the boards for more information
 on how to program the EEPROMs on these boards.
 
 Apps Directory
@@ -144,4 +168,4 @@ Apps Directory
 
 The Apps subdirectory contains the executable application files that
 are specific to RomWBW.  The source for these applications is found
-in the Source\Apps directory of the distribution.
+in the Source\Apps directory of the distribution.

Doc/ChangeLog.txt

@@ -14,7 +14,7 @@ Version 3.5
 - DDW: Added support for Duodyne Media board
 - WBW: Auto restore TMS video on user reset (CP/M warm boot)
 - L?B: Added support for NABU w/ RomWBW Option Board
-- M?P: Reorganization of Doc directory introducing subfolders
+- MAP: Reorganization of Doc directory introducing subfolders
 - WBW: Upgraded BBCBASIC to v5.00
 - W?S: Updated FLASH utility to v1.3.9
 - WBW: Support RCBus PS/2 Keyboard (EP/Sally)
@@ -22,6 +22,19 @@ Version 3.5
 - WBW: Preliminary support for S100 FPGA Z80 platform
 - WBW: Added simple serial (SSER) driver
 - WBW: Added preliminary support for S100 FPGA Z80 SD Cards
+- M?R: Consolidated ROM Applications document into the Applications document
+- M?R: Reviewed and substantially improved the Applications document
+- WBW: Added support for DS1305 RTC on S100 FPGA Z80
+- WBW: Added support for Les Bird's RCBus Graphics/Sound/Joystick module
+- WBW: Added support for Les Bird's Dual 16C550 UART module
+- WBW: Refactor UART driver for more flexible configuration
+- M?R: Added hour/minute/second display to timer app
+- WBW: Substantial customization of NZ-COM disk image
+- WBW: Refactor build post-processing (ZRC, ZZRCC, etc.)
+- MAP: Improved section Real Time Clock in User Guide document
+- WBW: Support for Hitachi HD44780-based LCD display
+- DRJ: Added support for Genesis STD Bus Z180 platform
+- MAP: Improved section Disk Management in User Guide document
 
 Version 3.4
 -----------
@@ -690,4 +703,4 @@ interrupts disabled the BIOS will now start OK even if some vagrant
 hardware is asserting an interrupt (DISKIO).  Seems like this is better
 anyway -- general idea is that we only enable interupts precisely
 when desired for very specific controled purposes since there is no
-concept of interrupt dispatching available.
+concept of interrupt dispatching available.

Doc/Contrib/ZSystem.txt

@@ -20,7 +20,7 @@ Beyond the construction and integration of the actual DOS itself, the majority o
 
 The remainder of this document details the changes I made as I went along.  In all cases, my goal was to keep the result as close to the original distribution as possible.  I started by copying all of the files from the distribution (contained in zsdos2.zip) into Support\ZSDOS.  From there I tested, modified, updated, and customized as documented below.  Finally, I cherry picked files that made sense to include on the ZSystem ROM disks.
 
-1. CLOCKS.DAT has been updated to include the RomWBW clock driver, HBCLK.  I have also added the SIMHCLOK clock driver.
+1. CLOCKS.DAT has been updated to include the RomWBW clock driver, WBWCLK.  I have also added the SIMHCLOK clock driver.
 
 2. STAMPS.DAT has been replaced with an updated version.  The update was called STAMPS11.DAT and was found on the Walnut Creek CP/M CDROM.  The original version has a bug that prevents RSX (resident system extension) mode to load properly.
 

Doc/Testing Notes.txt

@@ -1,144 +0,0 @@
-SIMH (X)
-----
-- Test UART driver
-- Test HDSK driver
-
-Zeta 1 (X)
-------
-- Test UART driver
-- Test PPP detection (startup w/ and w/o PPP)
-- Test boot to CRT
-- Test PPPSD driver
-- Test PPPCON driver (video & kbd)
-- Test FD driver
-- Test FDU app
-
-Zeta 2 (X)
-------
-- Test UART driver
-- Test PPP detection (startup w/ and w/o PPP)
-- Test boot to CRT
-- Test PPPSD driver
-- Test PPPCON driver (video & kbd)
-- Test FD driver
-- Test FDU app
-
-RCBus (X)
-------
-- Test SIO driver (Serial Module)
-- Test ACIA driver (Dual Serial Module)
-- Test IDE driver (Compact Flash Module)
-- Test PPIDE driver (IDE Module)
-- Test FD driver (SMC and WDC)
-- Test FDU app (SMC and WDC)
-
-N8-2312 (X)
--------
-- Test ASCI driver
-- Test SD driver (CSIO mode)
-- Test FD driver
-- Test FDU app
-- Test TMS driver (video & kbd)
-
-N8-2511 (X)
--------
-- Test ASCI driver
-- Test SD driver (Juha mode)
-- Test FD driver
-- Test FDU app
-- Test TMS driver (video & kbd)
-
-SBC (X)
----
-- Test UART driver
-- Test PPIDE driver
-- Test PPISD driver
-- Test PRP detection
-- Test boot to CRT console
-
-MK4 (X)
----
-- Test ASCI driver
-- Test IDE driver
-- Test SD driver
-- Test PRP detection
-
-RAMF (X)
-----
-- Test RAMF driver
-
-PRP (X)
----
-- Test PRPSD driver
-- Test PRPCON driver (video & kbd)
-
-SCG (X)
----
-- Test TMS driver (video)
-
-VDU (X)
----
-- Test CVDU driver (video & kbd)
-
-CVDU (X)
-----
-- Test CVDU driver (video & kbd)
-
-VGA (X)
----
-- Test VGA driver (video & kbd)
-
-DIO (X)
----
-- Test FD driver
-- Test FDU app
-- Test IDE driver
-
-DIO3 (X)
-----
-- Test FD driver
-- Test FDU app
-- Test PPIDE driver
-
-DIDE (X)
-----
-- Test FD driver
-- Test FDU app
-- Test IDE driver
-
-DSD (X)
----
-- Test SD driver
-
-4UART (X)
------
-- Test UART driver
-
-
-UNA (X)
----
-- General Startup
-- Boot from disk functionality
-- Image loading
-- Monitor
-- XM app
-- ASSIGN app
-- MODE app
-- SYSCOPY app
-- OSLDR app
-- FDU app
-- FDISK80 app
-
-GENERAL (X)
--------
-- Boot to ROM
-- Boot to Disk
-- Boot to Monitor
-- XM app
-- XM port auto-detect
-- ASSIGN app
-- MODE app
-- SYSCOPY app
-- FDU app
-- FDISK80 app
-- TUNE app

ReadMe.md

@@ -1,292 +1,293 @@
-
-
-**RomWBW ReadMe** \
-Version 3.5 \
-Wayne Warthen  ([wwarthen@gmail.com](mailto:wwarthen@gmail.com)) \
-30 Jun 2024
-
-# Overview
-
-RomWBW software provides a complete, commercial quality implementation
-of CP/M (and workalike) operating systems and applications for modern
-Z80/180/280 retro-computing hardware systems. A wide variety of
-platforms are supported including those produced by these developer
-communities:
-
-- [RetroBrew Computers](https://www.retrobrewcomputers.org)
-  (<https://www.retrobrewcomputers.org>)
-- [RC2014](https://rc2014.co.uk) (<https://rc2014.co.uk>),  
-  [RC2014-Z80](https://groups.google.com/g/rc2014-z80)
-  (<https://groups.google.com/g/rc2014-z80>)
-- [Retro Computing](https://groups.google.com/g/retro-comp)
-  (<https://groups.google.com/g/retro-comp>)
-- [Small Computer Central](https://smallcomputercentral.com/)
-  (<https://smallcomputercentral.com/>)
-
-A complete list of the currently supported platforms is found in the
-\[Installation\] section.
-
-General features include:
-
-- Z80 Family CPUs including Z80, Z180, and Z280
-- Banked memory services for several banking designs
-- Disk drivers for RAM, ROM, Floppy, IDE ATA/ATAPI, CF, SD, USB, Zip,
-  Iomega
-- Serial drivers including UART (16550-like), ASCI, ACIA, SIO
-- Video drivers including TMS9918, SY6545, MOS8563, HD6445
-- Keyboard (PS/2) drivers via VT8242 or PPI interfaces
-- Real time clock drivers including DS1302, BQ4845
-- OSes: CP/M 2.2, ZSDOS, CP/M 3, NZ-COM, ZPM3, QPM, p-System, and
-  FreeRTOS
-- Built-in VT-100 terminal emulation support
-
-RomWBW is distributed as both source code and pre-built ROM and disk
-images. Some of the provided software can be launched directly from the
-ROM firmware itself:
-
-- System Monitor
-- Operating Systems (CP/M 2.2, ZSDOS)
-- ROM BASIC (Nascom BASIC and Tasty BASIC)
-- ROM Forth
-
-A dynamic disk drive letter assignment mechanism allows mapping
-operating system drive letters to any available disk media.
-Additionally, mass storage devices (IDE Disk, CF Card, SD Card, etc.)
-support the use of multiple slices (up to 256 per device). Each slice
-contains a complete CP/M filesystem and can be mapped independently to
-any drive letter. This overcomes the inherent size limitations in legacy
-OSes and allows up to 2GB of accessible storage on a single device.
-
-The pre-built ROM firmware images are generally suitable for most users.
-However, it is also very easy to modify and build custom ROM images that
-fully tailor the firmware to your specific preferences. All tools
-required to build custom ROM firmware under Windows are included – no
-need to install assemblers, etc. The firmware can also be built using
-Linux or MacOS after confirming a few standard tools have been
-installed.
-
-Multiple disk images are provided in the distribution. Most disk images
-contain a complete, bootable, ready-to-run implementation of a specific
-operating system. A “combo” disk image contains multiple slices, each
-with a full operating system implementation. If you use this disk image,
-you can easily pick whichever operating system you want to boot without
-changing media.
-
-By design, RomWBW isolates all of the hardware specific functions in the
-ROM chip itself. The ROM provides a hardware abstraction layer such that
-all of the operating systems and applications on a disk will run on any
-RomWBW-based system. To put it simply, you can take a disk (or CF/SD/USB
-Card) and move it between systems transparently.
-
-A tool is provided that allows you to access a FAT-12/16/32 filesystem.
-The FAT filesystem may be coresident on the same disk media as RomWBW
-slices or on stand-alone media. This makes exchanging files with modern
-OSes such as Windows, MacOS, and Linux very easy.
-
-# Acquiring RomWBW
-
-The [RomWBW Repository](https://github.com/wwarthen/RomWBW)
-(<https://github.com/wwarthen/RomWBW>) on GitHub is the official
-distribution location for all project source and documentation. The
-fully-built distribution releases are available on the [RomWBW Releases
-Page](https://github.com/wwarthen/RomWBW/releases)
-(<https://github.com/wwarthen/RomWBW/releases>) of the repository. On
-this page, you will normally see a Development Snapshot as well as
-recent stable releases. Unless you have a specific reason, I suggest you
-stick to the most recent stable release. Expand the “Assets” drop-down
-for the release you want to download, then select the asset named
-RomWBW-vX.X.X-Package.zip. The Package asset includes all pre-built ROM
-and Disk images as well as full source code. The other assets contain
-only source code and do not have the pre-built ROM or disk images.
-
-All source code and distributions are maintained on GitHub. Code
-contributions are very welcome.
-
-# Installation & Operation
-
-In general, installation of RomWBW on your platform is very simple. You
-just need to program your ROM with the correct ROM image from the RomWBW
-distribution. Subsequently, you can write disk images on your disk
-drives (IDE disk, CF Card, SD Card, etc.) which then provides even more
-functionality.
-
-Complete instructions for installation and operation of RomWBW are found
-in the [RomWBW User
-Guide](https://github.com/wwarthen/RomWBW/raw/master/Doc/RomWBW%20User%20Guide.pdf).
-
-## Documentation
-
-Documentation for RomWBW includes:
-
-- [RomWBW User
-  Guide](https://github.com/wwarthen/RomWBW/raw/master/Doc/RomWBW%20User%20Guide.pdf)
-- [RomWBW System
-  Guide](https://github.com/wwarthen/RomWBW/raw/master/Doc/RomWBW%20System%20Guide.pdf)
-- [RomWBW
-  Applications](https://github.com/wwarthen/RomWBW/raw/master/Doc/RomWBW%20Applications.pdf)
-- [RomWBW ROM
-  Applications](https://github.com/wwarthen/RomWBW/raw/master/Doc/RomWBW%20ROM%20Applications.pdf)
-- [RomWBW
-  Errata](https://github.com/wwarthen/RomWBW/raw/master/Doc/RomWBW%20Errata.pdf)
-
-# Acknowledgments
-
-I want to acknowledge that a great deal of the code and inspiration for
-RomWBW has been provided by or derived from the work of others in the
-RetroBrew Computers Community. I sincerely appreciate all of their
-contributions. The list below is probably missing many names – please
-let me know if I missed you!
-
-- Andrew Lynch started it all when he created the N8VEM Z80 SBC which
-  became the first platform RomWBW supported. Some of his original code
-  can still be found in RomWBW.
-
-- Dan Werner wrote much of the code from which RomWBW was originally
-  derived and he has always been a great source of knowledge and advice.
-
-- Douglas Goodall contributed code, time, testing, and advice in “the
-  early days”. He created an entire suite of application programs to
-  enhance the use of RomWBW. Unfortunately, they have become unusable
-  due to internal changes within RomWBW. As of RomWBW 2.6, these
-  applications are no longer provided.
-
-- Sergey Kiselev created several hardware platforms for RomWBW including
-  the very popular Zeta.
-
-- David Giles created support for the Z180 CSIO which is now included SD
-  Card driver.
-
-- Phil Summers contributed the Forth and BASIC adaptations in ROM, the
-  AY-3-8910 sound driver, DMA support, and a long list of general code
-  and documentation enhancements.
-
-- Ed Brindley contributed some of the code that supports the RCBus
-  platform.
-
-- Spencer Owen created the RC2014 series of hobbyist kit computers which
-  has exponentially increased RomWBW usage. Some of his kits include
-  RomWBW.
-
-- Stephen Cousins has likewise created a series of hobbyist kit
-  computers at Small Computer Central and is distributing RomWBW with
-  many of them.
-
-- Alan Cox has contributed some driver code and has provided a great
-  deal of advice.
-
-- The CP/NET client files were developed by Douglas Miller.
-
-- Phillip Stevens contributed support for FreeRTOS.
-
-- Curt Mayer contributed the original Linux / MacOS build process.
-
-- UNA BIOS and FDISK80 are the products of John Coffman.
-
-- FLASH4 is a product of Will Sowerbutts.
-
-- CLRDIR is a product of Max Scane.
-
-- Tasty Basic is a product of Dimitri Theulings.
-
-- Dean Netherton contributed the sound driver interface and the SN76489
-  sound driver.
-
-- The RomWBW Disk Catalog document was produced by Mykl Orders.
-
-- Rob Prouse has created many of the supplemental disk images including
-  Aztec C, HiTech C, SLR Z80ASM, Turbo Pascal, Microsoft BASIC Compiler,
-  Microsoft Fortran Compiler, and a Games compendium.
-
-- Martin R has provided substantial help reviewing and improving the
-  User Guide.
-
-- Jacques Pelletier has contributed the DS1501 RTC driver code.
-
-- Jose Collado has contributed enhancements to the TMS driver including
-  compatibility with standard TMS register configuration.
-
-- Kevin Boone has contributed a generic HBIOS date/time utility (WDATE).
-
-- Matt Carroll has contributed a fix to XM.COM that corrects the port
-  specification when doing a send.
-
-- Dean Jenkins enhanced the build process to accommodate the Raspberry
-  Pi 4.
-
-- Tom Plano has contributed a new utility (HTALK) to allow talking
-  directly to HBIOS COM ports.
-
-- Lars Nelson has contributed several generic utilities such as a
-  universal (OS agnostic) UNARC application.
-
-- Dylan Hall added support for specifying a secondary console.
-
-- Bill Shen has contributed boot loaders for several of his systems.
-
-- Laszlo Szolnoki has contributed an EF9345 video display controller
-  driver.
-
-- Ladislau Szilagyi has contributed an enhanced version of CP/M Cowgol
-  that leverages RomWBW memory banking.
-
-- Les Bird has contributed support for the NABU w/ Option Board
-
-Contributions of all kinds to RomWBW are very welcome.
-
-# Licensing
-
-RomWBW is free software: you can redistribute it and/or modify it under
-the terms of the GNU General Public License as published by the Free
-Software Foundation, either version 3 of the License, or (at your
-option) any later version.
-
-RomWBW is distributed in the hope that it will be useful, but WITHOUT
-ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
-more details.
-
-You should have received a copy of the GNU General Public License along
-with RomWBW. If not, see <https://www.gnu.org/licenses/>.
-
-Portions of RomWBW were created by, contributed by, or derived from the
-work of others. It is believed that these works are being used in
-accordance with the intentions and/or licensing of their creators.
-
-If anyone feels their work is being used outside of its intended
-licensing, please notify:
-
-> Wayne Warthen  
-> <wwarthen@gmail.com>
-
-RomWBW is an aggregate work. It is composed of many individual,
-standalone programs that are distributed as a whole to function as a
-cohesive system. Each program may have its own licensing which may be
-different from other programs within the aggregate.
-
-In some cases, a single program (e.g., CP/M Operating System) is
-composed of multiple components with different licenses. It is believed
-that in all such cases the licenses are compatible with GPL version 3.
-
-RomWBW encourages code contributions from others. Contributors may
-assert their own copyright in their contributions by annotating the
-contributed source code appropriately. Contributors are further
-encouraged to submit their contributions via the RomWBW source code
-control system to ensure their contributions are clearly documented.
-
-All contributions to RomWBW are subject to this license.
-
-# Getting Assistance
-
-The best way to get assistance with RomWBW or any aspect of the
-RetroBrew Computers projects is via one of the community forums:
-
-- [RetroBrew Computers Forum](https://www.retrobrewcomputers.org/forum/)
-- [RC2014 Google
-  Group](https://groups.google.com/forum/#!forum/rc2014-z80)
-- [retro-comp Google
-  Group](https://groups.google.com/forum/#!forum/retro-comp)
-
-Submission of issues and bugs are welcome at the [RomWBW GitHub
-Repository](https://github.com/wwarthen/RomWBW).
-
-Also feel free to email Wayne Warthen at <wwarthen@gmail.com>.
+
+
+**RomWBW ReadMe** \
+Version 3.5 \
+Wayne Warthen  ([wwarthen@gmail.com](mailto:wwarthen@gmail.com)) \
+06 Sep 2024
+
+# Overview
+
+RomWBW software provides a complete, commercial quality implementation
+of CP/M (and workalike) operating systems and applications for modern
+Z80/180/280 retro-computing hardware systems. A wide variety of
+platforms are supported including those produced by these developer
+communities:
+
+- [RetroBrew Computers](https://www.retrobrewcomputers.org)
+  (<https://www.retrobrewcomputers.org>)
+- [RC2014](https://rc2014.co.uk) (<https://rc2014.co.uk>),  
+  [RC2014-Z80](https://groups.google.com/g/rc2014-z80)
+  (<https://groups.google.com/g/rc2014-z80>)
+- [Retro Computing](https://groups.google.com/g/retro-comp)
+  (<https://groups.google.com/g/retro-comp>)
+- [Small Computer Central](https://smallcomputercentral.com/)
+  (<https://smallcomputercentral.com/>)
+
+A complete list of the currently supported platforms is found in the
+\[Installation\] section.
+
+General features include:
+
+- Z80 Family CPUs including Z80, Z180, and Z280
+- Banked memory services for several banking designs
+- Disk drivers for RAM, ROM, Floppy, IDE ATA/ATAPI, CF, SD, USB, Zip,
+  Iomega
+- Serial drivers including UART (16550-like), ASCI, ACIA, SIO
+- Video drivers including TMS9918, SY6545, MOS8563, HD6445
+- Keyboard (PS/2) drivers via VT8242 or PPI interfaces
+- Real time clock drivers including DS1302, BQ4845
+- OSes: CP/M 2.2, ZSDOS, CP/M 3, NZ-COM, ZPM3, QPM, p-System, and
+  FreeRTOS
+- Built-in VT-100 terminal emulation support
+
+RomWBW is distributed as both source code and pre-built ROM and disk
+images. Some of the provided software can be launched directly from the
+ROM firmware itself:
+
+- System Monitor
+- Operating Systems (CP/M 2.2, ZSDOS)
+- ROM BASIC (Nascom BASIC and Tasty BASIC)
+- ROM Forth
+
+A dynamic disk drive letter assignment mechanism allows mapping
+operating system drive letters to any available disk media.
+Additionally, mass storage devices (IDE Disk, CF Card, SD Card, etc.)
+support the use of multiple slices (up to 256 per device). Each slice
+contains a complete CP/M filesystem and can be mapped independently to
+any drive letter. This overcomes the inherent size limitations in legacy
+OSes and allows up to 2GB of accessible storage on a single device.
+
+The pre-built ROM firmware images are generally suitable for most users.
+However, it is also very easy to modify and build custom ROM images that
+fully tailor the firmware to your specific preferences. All tools
+required to build custom ROM firmware under Windows are included – no
+need to install assemblers, etc. The firmware can also be built using
+Linux or MacOS after confirming a few standard tools have been
+installed.
+
+Multiple disk images are provided in the distribution. Most disk images
+contain a complete, bootable, ready-to-run implementation of a specific
+operating system. A “combo” disk image contains multiple slices, each
+with a full operating system implementation. If you use this disk image,
+you can easily pick whichever operating system you want to boot without
+changing media.
+
+By design, RomWBW isolates all of the hardware specific functions in the
+ROM chip itself. The ROM provides a hardware abstraction layer such that
+all of the operating systems and applications on a disk will run on any
+RomWBW-based system. To put it simply, you can take a disk (or CF/SD/USB
+Card) and move it between systems transparently.
+
+A tool is provided that allows you to access a FAT-12/16/32 filesystem.
+The FAT filesystem may be coresident on the same disk media as RomWBW
+slices or on stand-alone media. This makes exchanging files with modern
+OSes such as Windows, MacOS, and Linux very easy.
+
+# Acquiring RomWBW
+
+The [RomWBW Repository](https://github.com/wwarthen/RomWBW)
+(<https://github.com/wwarthen/RomWBW>) on GitHub is the official
+distribution location for all project source and documentation. The
+fully-built distribution releases are available on the [RomWBW Releases
+Page](https://github.com/wwarthen/RomWBW/releases)
+(<https://github.com/wwarthen/RomWBW/releases>) of the repository. On
+this page, you will normally see a Development Snapshot as well as
+recent stable releases. Unless you have a specific reason, I suggest you
+stick to the most recent stable release. Expand the “Assets” drop-down
+for the release you want to download, then select the asset named
+RomWBW-vX.X.X-Package.zip. The Package asset includes all pre-built ROM
+and Disk images as well as full source code. The other assets contain
+only source code and do not have the pre-built ROM or disk images.
+
+All source code and distributions are maintained on GitHub. Code
+contributions are very welcome.
+
+# Installation & Operation
+
+In general, installation of RomWBW on your platform is very simple. You
+just need to program your ROM with the correct ROM image from the RomWBW
+distribution. Subsequently, you can write disk images on your disk
+drives (IDE disk, CF Card, SD Card, etc.) which then provides even more
+functionality.
+
+Complete instructions for installation and operation of RomWBW are found
+in the [RomWBW User
+Guide](https://github.com/wwarthen/RomWBW/raw/master/Doc/RomWBW%20User%20Guide.pdf).
+
+## Documentation
+
+Documentation for RomWBW includes:
+
+- [RomWBW User
+  Guide](https://github.com/wwarthen/RomWBW/raw/master/Doc/RomWBW%20User%20Guide.pdf)
+- [RomWBW System
+  Guide](https://github.com/wwarthen/RomWBW/raw/master/Doc/RomWBW%20System%20Guide.pdf)
+- [RomWBW
+  Applications](https://github.com/wwarthen/RomWBW/raw/master/Doc/RomWBW%20Applications.pdf)
+- [RomWBW
+  Errata](https://github.com/wwarthen/RomWBW/raw/master/Doc/RomWBW%20Errata.pdf)
+
+# Acknowledgments
+
+I want to acknowledge that a great deal of the code and inspiration for
+RomWBW has been provided by or derived from the work of others in the
+RetroBrew Computers Community. I sincerely appreciate all of their
+contributions. The list below is probably missing many names – please
+let me know if I missed you!
+
+- Andrew Lynch started it all when he created the N8VEM Z80 SBC which
+  became the first platform RomWBW supported. Some of his original code
+  can still be found in RomWBW.
+
+- Dan Werner wrote much of the code from which RomWBW was originally
+  derived and he has always been a great source of knowledge and advice.
+
+- Douglas Goodall contributed code, time, testing, and advice in “the
+  early days”. He created an entire suite of application programs to
+  enhance the use of RomWBW. Unfortunately, they have become unusable
+  due to internal changes within RomWBW. As of RomWBW 2.6, these
+  applications are no longer provided.
+
+- Sergey Kiselev created several hardware platforms for RomWBW including
+  the very popular Zeta.
+
+- David Giles created support for the Z180 CSIO which is now included SD
+  Card driver.
+
+- Phil Summers contributed the Forth and BASIC adaptations in ROM, the
+  AY-3-8910 sound driver, DMA support, and a long list of general code
+  and documentation enhancements.
+
+- Ed Brindley contributed some of the code that supports the RCBus
+  platform.
+
+- Spencer Owen created the RC2014 series of hobbyist kit computers which
+  has exponentially increased RomWBW usage. Some of his kits include
+  RomWBW.
+
+- Stephen Cousins has likewise created a series of hobbyist kit
+  computers at Small Computer Central and is distributing RomWBW with
+  many of them.
+
+- Alan Cox has contributed some driver code and has provided a great
+  deal of advice.
+
+- The CP/NET client files were developed by Douglas Miller.
+
+- Phillip Stevens contributed support for FreeRTOS.
+
+- Curt Mayer contributed the original Linux / MacOS build process.
+
+- UNA BIOS and FDISK80 are the products of John Coffman.
+
+- FLASH4 is a product of Will Sowerbutts.
+
+- CLRDIR is a product of Max Scane.
+
+- Tasty Basic is a product of Dimitri Theulings.
+
+- Dean Netherton contributed the sound driver interface and the SN76489
+  sound driver.
+
+- The RomWBW Disk Catalog document was produced by Mykl Orders.
+
+- Rob Prouse has created many of the supplemental disk images including
+  Aztec C, HiTech C, SLR Z80ASM, Turbo Pascal, Microsoft BASIC Compiler,
+  Microsoft Fortran Compiler, and a Games compendium.
+
+- Martin R has provided substantial help reviewing and improving the
+  User Guide and Applications documents.
+
+- Mark Pruden has also contributed a great deal of content to the User
+  Guide.
+
+- Jacques Pelletier has contributed the DS1501 RTC driver code.
+
+- Jose Collado has contributed enhancements to the TMS driver including
+  compatibility with standard TMS register configuration.
+
+- Kevin Boone has contributed a generic HBIOS date/time utility (WDATE).
+
+- Matt Carroll has contributed a fix to XM.COM that corrects the port
+  specification when doing a send.
+
+- Dean Jenkins enhanced the build process to accommodate the Raspberry
+  Pi 4.
+
+- Tom Plano has contributed a new utility (HTALK) to allow talking
+  directly to HBIOS COM ports.
+
+- Lars Nelson has contributed several generic utilities such as a
+  universal (OS agnostic) UNARC application.
+
+- Dylan Hall added support for specifying a secondary console.
+
+- Bill Shen has contributed boot loaders for several of his systems.
+
+- Laszlo Szolnoki has contributed an EF9345 video display controller
+  driver.
+
+- Ladislau Szilagyi has contributed an enhanced version of CP/M Cowgol
+  that leverages RomWBW memory banking.
+
+- Les Bird has contributed support for the NABU w/ Option Board
+
+Contributions of all kinds to RomWBW are very welcome.
+
+# Licensing
+
+RomWBW is free software: you can redistribute it and/or modify it under
+the terms of the GNU General Public License as published by the Free
+Software Foundation, either version 3 of the License, or (at your
+option) any later version.
+
+RomWBW is distributed in the hope that it will be useful, but WITHOUT
+ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+more details.
+
+You should have received a copy of the GNU General Public License along
+with RomWBW. If not, see <https://www.gnu.org/licenses/>.
+
+Portions of RomWBW were created by, contributed by, or derived from the
+work of others. It is believed that these works are being used in
+accordance with the intentions and/or licensing of their creators.
+
+If anyone feels their work is being used outside of its intended
+licensing, please notify:
+
+> Wayne Warthen  
+> <wwarthen@gmail.com>
+
+RomWBW is an aggregate work. It is composed of many individual,
+standalone programs that are distributed as a whole to function as a
+cohesive system. Each program may have its own licensing which may be
+different from other programs within the aggregate.
+
+In some cases, a single program (e.g., CP/M Operating System) is
+composed of multiple components with different licenses. It is believed
+that in all such cases the licenses are compatible with GPL version 3.
+
+RomWBW encourages code contributions from others. Contributors may
+assert their own copyright in their contributions by annotating the
+contributed source code appropriately. Contributors are further
+encouraged to submit their contributions via the RomWBW source code
+control system to ensure their contributions are clearly documented.
+
+All contributions to RomWBW are subject to this license.
+
+# Getting Assistance
+
+The best way to get assistance with RomWBW or any aspect of the
+RetroBrew Computers projects is via one of the community forums:
+
+- [RetroBrew Computers Forum](https://www.retrobrewcomputers.org/forum/)
+- [RC2014 Google
+  Group](https://groups.google.com/forum/#!forum/rc2014-z80)
+- [retro-comp Google
+  Group](https://groups.google.com/forum/#!forum/retro-comp)
+
+Submission of issues and bugs are welcome at the [RomWBW GitHub
+Repository](https://github.com/wwarthen/RomWBW).
+
+Also feel free to email Wayne Warthen at <wwarthen@gmail.com>.

ReadMe.txt

@@ -1,297 +1,299 @@
-RomWBW ReadMe
-Wayne Warthen (wwarthen@gmail.com)
-30 Jun 2024
-
-
-
-OVERVIEW
-
-
-RomWBW software provides a complete, commercial quality implementation
-of CP/M (and workalike) operating systems and applications for modern
-Z80/180/280 retro-computing hardware systems. A wide variety of
-platforms are supported including those produced by these developer
-communities:
-
--   RetroBrew Computers (https://www.retrobrewcomputers.org)
--   RC2014 (https://rc2014.co.uk),
-    RC2014-Z80 (https://groups.google.com/g/rc2014-z80)
--   Retro Computing (https://groups.google.com/g/retro-comp)
--   Small Computer Central (https://smallcomputercentral.com/)
-
-A complete list of the currently supported platforms is found in the
-[Installation] section.
-
-General features include:
-
--   Z80 Family CPUs including Z80, Z180, and Z280
--   Banked memory services for several banking designs
--   Disk drivers for RAM, ROM, Floppy, IDE ATA/ATAPI, CF, SD, USB, Zip,
-    Iomega
--   Serial drivers including UART (16550-like), ASCI, ACIA, SIO
--   Video drivers including TMS9918, SY6545, MOS8563, HD6445
--   Keyboard (PS/2) drivers via VT8242 or PPI interfaces
--   Real time clock drivers including DS1302, BQ4845
--   OSes: CP/M 2.2, ZSDOS, CP/M 3, NZ-COM, ZPM3, QPM, p-System, and
-    FreeRTOS
--   Built-in VT-100 terminal emulation support
-
-RomWBW is distributed as both source code and pre-built ROM and disk
-images. Some of the provided software can be launched directly from the
-ROM firmware itself:
-
--   System Monitor
--   Operating Systems (CP/M 2.2, ZSDOS)
--   ROM BASIC (Nascom BASIC and Tasty BASIC)
--   ROM Forth
-
-A dynamic disk drive letter assignment mechanism allows mapping
-operating system drive letters to any available disk media.
-Additionally, mass storage devices (IDE Disk, CF Card, SD Card, etc.)
-support the use of multiple slices (up to 256 per device). Each slice
-contains a complete CP/M filesystem and can be mapped independently to
-any drive letter. This overcomes the inherent size limitations in legacy
-OSes and allows up to 2GB of accessible storage on a single device.
-
-The pre-built ROM firmware images are generally suitable for most users.
-However, it is also very easy to modify and build custom ROM images that
-fully tailor the firmware to your specific preferences. All tools
-required to build custom ROM firmware under Windows are included – no
-need to install assemblers, etc. The firmware can also be built using
-Linux or MacOS after confirming a few standard tools have been
-installed.
-
-Multiple disk images are provided in the distribution. Most disk images
-contain a complete, bootable, ready-to-run implementation of a specific
-operating system. A “combo” disk image contains multiple slices, each
-with a full operating system implementation. If you use this disk image,
-you can easily pick whichever operating system you want to boot without
-changing media.
-
-By design, RomWBW isolates all of the hardware specific functions in the
-ROM chip itself. The ROM provides a hardware abstraction layer such that
-all of the operating systems and applications on a disk will run on any
-RomWBW-based system. To put it simply, you can take a disk (or CF/SD/USB
-Card) and move it between systems transparently.
-
-A tool is provided that allows you to access a FAT-12/16/32 filesystem.
-The FAT filesystem may be coresident on the same disk media as RomWBW
-slices or on stand-alone media. This makes exchanging files with modern
-OSes such as Windows, MacOS, and Linux very easy.
-
-
-
-ACQUIRING ROMWBW
-
-
-The RomWBW Repository (https://github.com/wwarthen/RomWBW) on GitHub is
-the official distribution location for all project source and
-documentation. The fully-built distribution releases are available on
-the RomWBW Releases Page (https://github.com/wwarthen/RomWBW/releases)
-of the repository. On this page, you will normally see a Development
-Snapshot as well as recent stable releases. Unless you have a specific
-reason, I suggest you stick to the most recent stable release. Expand
-the “Assets” drop-down for the release you want to download, then select
-the asset named RomWBW-vX.X.X-Package.zip. The Package asset includes
-all pre-built ROM and Disk images as well as full source code. The other
-assets contain only source code and do not have the pre-built ROM or
-disk images.
-
-All source code and distributions are maintained on GitHub. Code
-contributions are very welcome.
-
-
-
-INSTALLATION & OPERATION
-
-
-In general, installation of RomWBW on your platform is very simple. You
-just need to program your ROM with the correct ROM image from the RomWBW
-distribution. Subsequently, you can write disk images on your disk
-drives (IDE disk, CF Card, SD Card, etc.) which then provides even more
-functionality.
-
-Complete instructions for installation and operation of RomWBW are found
-in the RomWBW User Guide.
-
-
-Documentation
-
-Documentation for RomWBW includes:
-
--   RomWBW User Guide
--   RomWBW System Guide
--   RomWBW Applications
--   RomWBW ROM Applications
--   RomWBW Errata
-
-
-
-ACKNOWLEDGMENTS
-
-
-I want to acknowledge that a great deal of the code and inspiration for
-RomWBW has been provided by or derived from the work of others in the
-RetroBrew Computers Community. I sincerely appreciate all of their
-contributions. The list below is probably missing many names – please
-let me know if I missed you!
-
--   Andrew Lynch started it all when he created the N8VEM Z80 SBC which
-    became the first platform RomWBW supported. Some of his original
-    code can still be found in RomWBW.
-
--   Dan Werner wrote much of the code from which RomWBW was originally
-    derived and he has always been a great source of knowledge and
-    advice.
-
--   Douglas Goodall contributed code, time, testing, and advice in “the
-    early days”. He created an entire suite of application programs to
-    enhance the use of RomWBW. Unfortunately, they have become unusable
-    due to internal changes within RomWBW. As of RomWBW 2.6, these
-    applications are no longer provided.
-
--   Sergey Kiselev created several hardware platforms for RomWBW
-    including the very popular Zeta.
-
--   David Giles created support for the Z180 CSIO which is now included
-    SD Card driver.
-
--   Phil Summers contributed the Forth and BASIC adaptations in ROM, the
-    AY-3-8910 sound driver, DMA support, and a long list of general code
-    and documentation enhancements.
-
--   Ed Brindley contributed some of the code that supports the RCBus
-    platform.
-
--   Spencer Owen created the RC2014 series of hobbyist kit computers
-    which has exponentially increased RomWBW usage. Some of his kits
-    include RomWBW.
-
--   Stephen Cousins has likewise created a series of hobbyist kit
-    computers at Small Computer Central and is distributing RomWBW with
-    many of them.
-
--   Alan Cox has contributed some driver code and has provided a great
-    deal of advice.
-
--   The CP/NET client files were developed by Douglas Miller.
-
--   Phillip Stevens contributed support for FreeRTOS.
-
--   Curt Mayer contributed the original Linux / MacOS build process.
-
--   UNA BIOS and FDISK80 are the products of John Coffman.
-
--   FLASH4 is a product of Will Sowerbutts.
-
--   CLRDIR is a product of Max Scane.
-
--   Tasty Basic is a product of Dimitri Theulings.
-
--   Dean Netherton contributed the sound driver interface and the
-    SN76489 sound driver.
-
--   The RomWBW Disk Catalog document was produced by Mykl Orders.
-
--   Rob Prouse has created many of the supplemental disk images
-    including Aztec C, HiTech C, SLR Z80ASM, Turbo Pascal, Microsoft
-    BASIC Compiler, Microsoft Fortran Compiler, and a Games compendium.
-
--   Martin R has provided substantial help reviewing and improving the
-    User Guide.
-
--   Jacques Pelletier has contributed the DS1501 RTC driver code.
-
--   Jose Collado has contributed enhancements to the TMS driver
-    including compatibility with standard TMS register configuration.
-
--   Kevin Boone has contributed a generic HBIOS date/time utility
-    (WDATE).
-
--   Matt Carroll has contributed a fix to XM.COM that corrects the port
-    specification when doing a send.
-
--   Dean Jenkins enhanced the build process to accommodate the Raspberry
-    Pi 4.
-
--   Tom Plano has contributed a new utility (HTALK) to allow talking
-    directly to HBIOS COM ports.
-
--   Lars Nelson has contributed several generic utilities such as a
-    universal (OS agnostic) UNARC application.
-
--   Dylan Hall added support for specifying a secondary console.
-
--   Bill Shen has contributed boot loaders for several of his systems.
-
--   Laszlo Szolnoki has contributed an EF9345 video display controller
-    driver.
-
--   Ladislau Szilagyi has contributed an enhanced version of CP/M Cowgol
-    that leverages RomWBW memory banking.
-
--   Les Bird has contributed support for the NABU w/ Option Board
-
-Contributions of all kinds to RomWBW are very welcome.
-
-
-
-LICENSING
-
-
-RomWBW is free software: you can redistribute it and/or modify it under
-the terms of the GNU General Public License as published by the Free
-Software Foundation, either version 3 of the License, or (at your
-option) any later version.
-
-RomWBW is distributed in the hope that it will be useful, but WITHOUT
-ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
-more details.
-
-You should have received a copy of the GNU General Public License along
-with RomWBW. If not, see https://www.gnu.org/licenses/.
-
-Portions of RomWBW were created by, contributed by, or derived from the
-work of others. It is believed that these works are being used in
-accordance with the intentions and/or licensing of their creators.
-
-If anyone feels their work is being used outside of its intended
-licensing, please notify:
-
-  Wayne Warthen
-  wwarthen@gmail.com
-
-RomWBW is an aggregate work. It is composed of many individual,
-standalone programs that are distributed as a whole to function as a
-cohesive system. Each program may have its own licensing which may be
-different from other programs within the aggregate.
-
-In some cases, a single program (e.g., CP/M Operating System) is
-composed of multiple components with different licenses. It is believed
-that in all such cases the licenses are compatible with GPL version 3.
-
-RomWBW encourages code contributions from others. Contributors may
-assert their own copyright in their contributions by annotating the
-contributed source code appropriately. Contributors are further
-encouraged to submit their contributions via the RomWBW source code
-control system to ensure their contributions are clearly documented.
-
-All contributions to RomWBW are subject to this license.
-
-
-
-GETTING ASSISTANCE
-
-
-The best way to get assistance with RomWBW or any aspect of the
-RetroBrew Computers projects is via one of the community forums:
-
--   RetroBrew Computers Forum
--   RC2014 Google Group
--   retro-comp Google Group
-
-Submission of issues and bugs are welcome at the RomWBW GitHub
-Repository.
-
-Also feel free to email Wayne Warthen at wwarthen@gmail.com.
+RomWBW ReadMe
+Wayne Warthen (wwarthen@gmail.com)
+06 Sep 2024
+
+
+
+OVERVIEW
+
+
+RomWBW software provides a complete, commercial quality implementation
+of CP/M (and workalike) operating systems and applications for modern
+Z80/180/280 retro-computing hardware systems. A wide variety of
+platforms are supported including those produced by these developer
+communities:
+
+-   RetroBrew Computers (https://www.retrobrewcomputers.org)
+-   RC2014 (https://rc2014.co.uk),
+    RC2014-Z80 (https://groups.google.com/g/rc2014-z80)
+-   Retro Computing (https://groups.google.com/g/retro-comp)
+-   Small Computer Central (https://smallcomputercentral.com/)
+
+A complete list of the currently supported platforms is found in the
+[Installation] section.
+
+General features include:
+
+-   Z80 Family CPUs including Z80, Z180, and Z280
+-   Banked memory services for several banking designs
+-   Disk drivers for RAM, ROM, Floppy, IDE ATA/ATAPI, CF, SD, USB, Zip,
+    Iomega
+-   Serial drivers including UART (16550-like), ASCI, ACIA, SIO
+-   Video drivers including TMS9918, SY6545, MOS8563, HD6445
+-   Keyboard (PS/2) drivers via VT8242 or PPI interfaces
+-   Real time clock drivers including DS1302, BQ4845
+-   OSes: CP/M 2.2, ZSDOS, CP/M 3, NZ-COM, ZPM3, QPM, p-System, and
+    FreeRTOS
+-   Built-in VT-100 terminal emulation support
+
+RomWBW is distributed as both source code and pre-built ROM and disk
+images. Some of the provided software can be launched directly from the
+ROM firmware itself:
+
+-   System Monitor
+-   Operating Systems (CP/M 2.2, ZSDOS)
+-   ROM BASIC (Nascom BASIC and Tasty BASIC)
+-   ROM Forth
+
+A dynamic disk drive letter assignment mechanism allows mapping
+operating system drive letters to any available disk media.
+Additionally, mass storage devices (IDE Disk, CF Card, SD Card, etc.)
+support the use of multiple slices (up to 256 per device). Each slice
+contains a complete CP/M filesystem and can be mapped independently to
+any drive letter. This overcomes the inherent size limitations in legacy
+OSes and allows up to 2GB of accessible storage on a single device.
+
+The pre-built ROM firmware images are generally suitable for most users.
+However, it is also very easy to modify and build custom ROM images that
+fully tailor the firmware to your specific preferences. All tools
+required to build custom ROM firmware under Windows are included – no
+need to install assemblers, etc. The firmware can also be built using
+Linux or MacOS after confirming a few standard tools have been
+installed.
+
+Multiple disk images are provided in the distribution. Most disk images
+contain a complete, bootable, ready-to-run implementation of a specific
+operating system. A “combo” disk image contains multiple slices, each
+with a full operating system implementation. If you use this disk image,
+you can easily pick whichever operating system you want to boot without
+changing media.
+
+By design, RomWBW isolates all of the hardware specific functions in the
+ROM chip itself. The ROM provides a hardware abstraction layer such that
+all of the operating systems and applications on a disk will run on any
+RomWBW-based system. To put it simply, you can take a disk (or CF/SD/USB
+Card) and move it between systems transparently.
+
+A tool is provided that allows you to access a FAT-12/16/32 filesystem.
+The FAT filesystem may be coresident on the same disk media as RomWBW
+slices or on stand-alone media. This makes exchanging files with modern
+OSes such as Windows, MacOS, and Linux very easy.
+
+
+
+ACQUIRING ROMWBW
+
+
+The RomWBW Repository (https://github.com/wwarthen/RomWBW) on GitHub is
+the official distribution location for all project source and
+documentation. The fully-built distribution releases are available on
+the RomWBW Releases Page (https://github.com/wwarthen/RomWBW/releases)
+of the repository. On this page, you will normally see a Development
+Snapshot as well as recent stable releases. Unless you have a specific
+reason, I suggest you stick to the most recent stable release. Expand
+the “Assets” drop-down for the release you want to download, then select
+the asset named RomWBW-vX.X.X-Package.zip. The Package asset includes
+all pre-built ROM and Disk images as well as full source code. The other
+assets contain only source code and do not have the pre-built ROM or
+disk images.
+
+All source code and distributions are maintained on GitHub. Code
+contributions are very welcome.
+
+
+
+INSTALLATION & OPERATION
+
+
+In general, installation of RomWBW on your platform is very simple. You
+just need to program your ROM with the correct ROM image from the RomWBW
+distribution. Subsequently, you can write disk images on your disk
+drives (IDE disk, CF Card, SD Card, etc.) which then provides even more
+functionality.
+
+Complete instructions for installation and operation of RomWBW are found
+in the RomWBW User Guide.
+
+
+Documentation
+
+Documentation for RomWBW includes:
+
+-   RomWBW User Guide
+-   RomWBW System Guide
+-   RomWBW Applications
+-   RomWBW Errata
+
+
+
+ACKNOWLEDGMENTS
+
+
+I want to acknowledge that a great deal of the code and inspiration for
+RomWBW has been provided by or derived from the work of others in the
+RetroBrew Computers Community. I sincerely appreciate all of their
+contributions. The list below is probably missing many names – please
+let me know if I missed you!
+
+-   Andrew Lynch started it all when he created the N8VEM Z80 SBC which
+    became the first platform RomWBW supported. Some of his original
+    code can still be found in RomWBW.
+
+-   Dan Werner wrote much of the code from which RomWBW was originally
+    derived and he has always been a great source of knowledge and
+    advice.
+
+-   Douglas Goodall contributed code, time, testing, and advice in “the
+    early days”. He created an entire suite of application programs to
+    enhance the use of RomWBW. Unfortunately, they have become unusable
+    due to internal changes within RomWBW. As of RomWBW 2.6, these
+    applications are no longer provided.
+
+-   Sergey Kiselev created several hardware platforms for RomWBW
+    including the very popular Zeta.
+
+-   David Giles created support for the Z180 CSIO which is now included
+    SD Card driver.
+
+-   Phil Summers contributed the Forth and BASIC adaptations in ROM, the
+    AY-3-8910 sound driver, DMA support, and a long list of general code
+    and documentation enhancements.
+
+-   Ed Brindley contributed some of the code that supports the RCBus
+    platform.
+
+-   Spencer Owen created the RC2014 series of hobbyist kit computers
+    which has exponentially increased RomWBW usage. Some of his kits
+    include RomWBW.
+
+-   Stephen Cousins has likewise created a series of hobbyist kit
+    computers at Small Computer Central and is distributing RomWBW with
+    many of them.
+
+-   Alan Cox has contributed some driver code and has provided a great
+    deal of advice.
+
+-   The CP/NET client files were developed by Douglas Miller.
+
+-   Phillip Stevens contributed support for FreeRTOS.
+
+-   Curt Mayer contributed the original Linux / MacOS build process.
+
+-   UNA BIOS and FDISK80 are the products of John Coffman.
+
+-   FLASH4 is a product of Will Sowerbutts.
+
+-   CLRDIR is a product of Max Scane.
+
+-   Tasty Basic is a product of Dimitri Theulings.
+
+-   Dean Netherton contributed the sound driver interface and the
+    SN76489 sound driver.
+
+-   The RomWBW Disk Catalog document was produced by Mykl Orders.
+
+-   Rob Prouse has created many of the supplemental disk images
+    including Aztec C, HiTech C, SLR Z80ASM, Turbo Pascal, Microsoft
+    BASIC Compiler, Microsoft Fortran Compiler, and a Games compendium.
+
+-   Martin R has provided substantial help reviewing and improving the
+    User Guide and Applications documents.
+
+-   Mark Pruden has also contributed a great deal of content to the User
+    Guide.
+
+-   Jacques Pelletier has contributed the DS1501 RTC driver code.
+
+-   Jose Collado has contributed enhancements to the TMS driver
+    including compatibility with standard TMS register configuration.
+
+-   Kevin Boone has contributed a generic HBIOS date/time utility
+    (WDATE).
+
+-   Matt Carroll has contributed a fix to XM.COM that corrects the port
+    specification when doing a send.
+
+-   Dean Jenkins enhanced the build process to accommodate the Raspberry
+    Pi 4.
+
+-   Tom Plano has contributed a new utility (HTALK) to allow talking
+    directly to HBIOS COM ports.
+
+-   Lars Nelson has contributed several generic utilities such as a
+    universal (OS agnostic) UNARC application.
+
+-   Dylan Hall added support for specifying a secondary console.
+
+-   Bill Shen has contributed boot loaders for several of his systems.
+
+-   Laszlo Szolnoki has contributed an EF9345 video display controller
+    driver.
+
+-   Ladislau Szilagyi has contributed an enhanced version of CP/M Cowgol
+    that leverages RomWBW memory banking.
+
+-   Les Bird has contributed support for the NABU w/ Option Board
+
+Contributions of all kinds to RomWBW are very welcome.
+
+
+
+LICENSING
+
+
+RomWBW is free software: you can redistribute it and/or modify it under
+the terms of the GNU General Public License as published by the Free
+Software Foundation, either version 3 of the License, or (at your
+option) any later version.
+
+RomWBW is distributed in the hope that it will be useful, but WITHOUT
+ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+more details.
+
+You should have received a copy of the GNU General Public License along
+with RomWBW. If not, see https://www.gnu.org/licenses/.
+
+Portions of RomWBW were created by, contributed by, or derived from the
+work of others. It is believed that these works are being used in
+accordance with the intentions and/or licensing of their creators.
+
+If anyone feels their work is being used outside of its intended
+licensing, please notify:
+
+  Wayne Warthen
+  wwarthen@gmail.com
+
+RomWBW is an aggregate work. It is composed of many individual,
+standalone programs that are distributed as a whole to function as a
+cohesive system. Each program may have its own licensing which may be
+different from other programs within the aggregate.
+
+In some cases, a single program (e.g., CP/M Operating System) is
+composed of multiple components with different licenses. It is believed
+that in all such cases the licenses are compatible with GPL version 3.
+
+RomWBW encourages code contributions from others. Contributors may
+assert their own copyright in their contributions by annotating the
+contributed source code appropriately. Contributors are further
+encouraged to submit their contributions via the RomWBW source code
+control system to ensure their contributions are clearly documented.
+
+All contributions to RomWBW are subject to this license.
+
+
+
+GETTING ASSISTANCE
+
+
+The best way to get assistance with RomWBW or any aspect of the
+RetroBrew Computers projects is via one of the community forums:
+
+-   RetroBrew Computers Forum
+-   RC2014 Google Group
+-   retro-comp Google Group
+
+Submission of issues and bugs are welcome at the RomWBW GitHub
+Repository.
+
+Also feel free to email Wayne Warthen at wwarthen@gmail.com.

Source/Apps/Test/inttest/Build.cmd

@@ -8,4 +8,5 @@ set TASMTABS=%TOOLS%\tasm32
 tasm -t180 -g3 -fFF inttest.asm inttest.com inttest.lst || exit /b
 
 copy /Y inttest.com ..\..\..\..\Binary\Apps\Test\ || exit /b
+copy /Y inttest.doc ..\..\..\..\Binary\Apps\Test\ || exit /b
 

Source/Apps/Test/inttest/Makefile

@@ -1,5 +1,7 @@
 OBJECTS = inttest.com
+DOCS = inttest.doc
 DEST = ../../../../Binary/Apps/Test
+DOCDEST = ../../../../Binary/Apps/Test
 TOOLS =../../../../Tools
 
 USETASM=1

Source/Apps/Test/inttest/inttest.doc

@@ -0,0 +1,44 @@
+INTTEST
+=======
+
+RomWBW includes an API allowing applications to "hook" interrupts.
+The `INTTEST` utility allows you to test this functionality.
+
+
+** Syntax **
+
+`INTTEST`
+
+
+** Usage **
+
+`INTTEST` is an interactive application.  At startup, it will display
+a list of the interrupt vector slots in your system along with the
+current vector address for each of them.
+
+It then prompts you to enter the slot number (in hex) of a vector to
+hook.  After entering this, the application will watch the hooked
+vector and countdown from 0xFF to 0x00 as interrupts are noted.
+
+When the counter reaches 0x00, the interrupt is unhooked and the
+application terminates.  The application can also be terminated by
+pressing <esc>.
+
+
+** Notes **
+
+If your system is running without interrupts active, the application
+will terminate immediately.
+
+All slots have vectors even if the corresponding interrupt is not
+doing anything.  In this case, the vector is pointing to the "bad
+interrupt" handler.
+
+If you hook a vector that is not receiving any interrupts, the
+down-counter will not do anything.
+
+
+** Etymology* *
+
+The `INTTEST` command is an original product and the source code is
+provided in the RomWBW distribution.

Source/Apps/Tune/tune.asm

@@ -49,6 +49,8 @@
 ;   2024-02-23 [WBW] Include ACR value in config table
 ;   2024-04-16 [WBW] Add support for NABU AY-3-8910
 ;   2024-05-10 [WBW] Hack to avoid corrupting bits 6&7 of PSG R7 for NABU!
+;   2024-07-08 [WBW] Add support for Les Bird's Graphics, Sound, Joystick
+;   2024-07-11 [WBW] Updated, Les Bird's module now uses same settings as EB6
 ;_______________________________________________________________________________
 ;
 ; ToDo:
@@ -572,8 +574,8 @@ CFGSIZ	.EQU	$ - CFGTBL
 	.DB	$07,	$D8,	$D0,	$D8,	$FF,	$FF,	$FF	; RCZ80 W/ RC SOUND MODULE (EB)
 	.DW	HWSTR_RCEB
 ;
-	.DB	$07,	$A0,	$A1,	$A2,	$FF,	$FF,	$FF	; RCZ80 W/ RC SOUND MODULE (EB Rev 6)
-	.DW	HWSTR_RCEB6
+	.DB	$07,	$A0,	$A1,	$A2,	$FF,	$FF,	$FF	; RCZ80 W/ RC SOUND MODULE (MSX)
+	.DW	HWSTR_RCMSX
 ;
 	.DB	$07,	$D1,	$D0,	$D0,	$FF,	$FF,	$FF	; RCZ80 W/ RC SOUND MODULE (MF)
 	.DW	HWSTR_RCMF
@@ -584,8 +586,8 @@ CFGSIZ	.EQU	$ - CFGTBL
 	.DB	$08,	$68,	$60,	$68,	$C0,	$FF,	$FF	; RCZ180 W/ RC SOUND MODULE (EB)
 	.DW	HWSTR_RCEB
 ;
-	.DB	$08,	$A0,	$A1,	$A2,	$C0,	$FF,	$FF	; RCZ180 W/ RC SOUND MODULE (EB Rev 6)
-	.DW	HWSTR_RCEB6
+	.DB	$08,	$A0,	$A1,	$A2,	$C0,	$FF,	$FF	; RCZ180 W/ RC SOUND MODULE (MSX)
+	.DW	HWSTR_RCMSX
 ;
 	.DB	$08,	$61,	$60,	$60,	$C0,	$FF,	$FF	; RCZ180 W/ RC SOUND MODULE (MF)
 	.DW	HWSTR_RCMF
@@ -596,8 +598,8 @@ CFGSIZ	.EQU	$ - CFGTBL
 	.DB	$09,	$D8,	$D0,	$D8,	$FF,	$FF,	$FF	; EZZ80 W/ RC SOUND MODULE (EB)
 	.DW	HWSTR_RCEB
 ;
-	.DB	$09,	$A0,	$A1,	$A2,	$FF,	$FF,	$FF	; EZZ80 W/ RC SOUND MODULE (EB Rev 6)
-	.DW	HWSTR_RCEB6
+	.DB	$09,	$A0,	$A1,	$A2,	$FF,	$FF,	$FF	; EZZ80 W/ RC SOUND MODULE (MSX)
+	.DW	HWSTR_RCMSX
 ;
 	.DB	$09,	$D1,	$D0,	$D0,	$FF,	$FF,	$FF	; EZZ80 W/ RC SOUND MODULE (MF)
 	.DW	HWSTR_RCMF
@@ -608,8 +610,8 @@ CFGSIZ	.EQU	$ - CFGTBL
 	.DB	$0A,	$68,	$60,	$68,	$C0,	$FF,	$FF	; SCZ180 W/ RC SOUND MODULE (EB)
 	.DW	HWSTR_RCEB
 ;
-	.DB	$0A,	$A0,	$A1,	$A2,	$C0,	$FF,	$FF	; SCZ180 W/ RC SOUND MODULE (EB Rev 6)
-	.DW	HWSTR_RCEB6
+	.DB	$0A,	$A0,	$A1,	$A2,	$C0,	$FF,	$FF	; SCZ180 W/ RC SOUND MODULE (MS6)
+	.DW	HWSTR_RCMSX
 ;
 	.DB	$0A,	$61,	$60,	$60,	$C0,	$FF,	$FF	; SCZ180 W/ RC SOUND MODULE (MF)
 	.DW	HWSTR_RCMF
@@ -620,8 +622,8 @@ CFGSIZ	.EQU	$ - CFGTBL
 	.DB	$0B,	$D8,	$D0,	$D8,	$FF,	$FF,	$FF	; RCZ280 W/ RC SOUND MODULE (EB)
 	.DW	HWSTR_RCEB
 ;
-	.DB	$0B,	$A0,	$A1,	$A2,	$FF,	$FF,	$FF	; RCZ280 W/ RC SOUND MODULE (EB Rev 6)
-	.DW	HWSTR_RCEB6
+	.DB	$0B,	$A0,	$A1,	$A2,	$FF,	$FF,	$FF	; RCZ280 W/ RC SOUND MODULE (MSX)
+	.DW	HWSTR_RCMSX
 ;
 	.DB	$0B,	$D1,	$D0,	$D0,	$FF,	$FF,	$FF	; RCZ280 W/ RC SOUND MODULE (MF)
 	.DW	HWSTR_RCMF
@@ -666,7 +668,7 @@ TMP		.DB	0	; work around use of undocumented Z80
 HBIOSMD		.DB	0	; NON-ZERO IF USING HBIOS SOUND DRIVER, ZERO OTHERWISE
 OCTAVEADJ	.DB	0	; AMOUNT TO ADJUST OCTAVE UP OR DOWN
 
-MSGBAN		.DB	"Tune Player for RomWBW v3.8, 10-May-2024",0
+MSGBAN		.DB	"Tune Player for RomWBW v3.10, 11-Jul-2024",0
 MSGUSE		.DB	"Copyright (C) 2024, Wayne Warthen, GNU GPL v3",13,10
 		.DB	"PTxPlayer Copyright (C) 2004-2007 S.V.Bulba",13,10
 		.DB	"MYMPlay by Marq/Lieves!Tuore",13,10,13,10
@@ -687,7 +689,7 @@ MSGERR		.DB	"App Error", 0
 HWSTR_SCG	.DB	"SCG ECB Board",0
 HWSTR_N8	.DB	"N8 Onboard Sound",0
 HWSTR_RCEB	.DB	"RCBus Sound Module (EB)",0
-HWSTR_RCEB6	.DB	"RCBus Sound Module (EBv6)",0
+HWSTR_RCMSX	.DB	"RCBus Sound Module (MSX)",0
 HWSTR_RCMF	.DB	"RCBus Sound Module (MF)",0
 HWSTR_LINC	.DB	"Z50 LiNC Sound Module",0
 HWSTR_MBC	.DB	"NHYODYNE Sound Module",0

Source/Apps/rtc.asm

@@ -33,6 +33,8 @@
 ;
 ;[2023/07/07] v1.9 Support DUODYNE
 ;
+;[2024/09/02] v1.10  Support Genesis STD Z180
+;
 ; Constants
 ;
 mask_data	.EQU	%10000000	; RTC data line
@@ -52,6 +54,7 @@ PORT_RCZ280	.EQU	$C0		; RTC port for RCZ280
 PORT_MBC	.EQU	$70		; RTC port for MBC
 PORT_RPH	.EQU	$84		; RTC port for RHYOPHYRE
 PORT_DUO	.EQU	$94		; RTC port for DUODYNE
+PORT_STDZ180 .EQU $84         ; RTC Port for STD Bus Z180 board
 
 
 BDOS		.EQU	5		; BDOS invocation vector
@@ -1143,7 +1146,13 @@ HINIT:
 	CP	17		; DUODYNE
 	JP	Z,RTC_INIT2
 ;
-	; Unknown platform
+	LD	C,PORT_STDZ180
+	LD	DE,PLT_STDZ180
+	CP	21		; STD Z180
+	JP	Z,RTC_INIT2
+;
+
+; Unknown platform
 	LD	DE,PLTERR	; BIOS error message
 	LD	C,9		; BDOS string display function
 	CALL	BDOS		; Do it
@@ -1769,6 +1778,7 @@ PLT_RCZ280	.TEXT	", RCBus Z280 RTC Module Latch Port 0xC0\r\n$"
 PLT_MBC		.TEXT	", MBC RTC Latch Port 0x70\r\n$"
 PLT_RPH		.TEXT	", RHYOPHYRE RTC Latch Port 0x84\r\n$"
 PLT_DUO		.TEXT	", DUODYNE RTC Latch Port 0x70\r\n$"
+PLT_STDZ180 .TEXT ", STD Z180 RTC Module latch port 0x84\r\n$"
 
 ;
 ; Generic FOR-NEXT loop algorithm

Source/Doc/Basic.h

@@ -11,7 +11,6 @@ $define{doc_orgurl}{www.retrobrewcomputers.org}$
 $define{doc_user}{[RomWBW User Guide]($doc_root$/RomWBW User Guide.pdf)}$
 $define{doc_sys}{[RomWBW System Guide]($doc_root$/RomWBW System Guide.pdf)}$
 $define{doc_apps}{[RomWBW Applications]($doc_root$/RomWBW Applications.pdf)}$
-$define{doc_romapps}{[RomWBW ROM Applications]($doc_root$/RomWBW ROM Applications.pdf)}$
 $define{doc_catalog}{[RomWBW Disk Catalog]($doc_root$/RomWBW Disk Catalog.pdf)}$
 $define{doc_errata}{[RomWBW Errata]($doc_root$/RomWBW Errata.pdf)}$
 

Source/Doc/Build.cmd

@@ -2,8 +2,12 @@
 setlocal
 
 ::
-:: NOTE: Pandoc and Latex (MiKTeX or TexLive) must be installed
-:: and available on commandline for this build to work!!!
+:: NOTE: Pandoc, LuaLatex (MiKTeX or TexLive), and Roboto Font
+:: must be installed and available on commandline for this build to work!!!
+::
+:: - Pandoc (https://pandoc.org/)
+:: - MiKTeX (https://miktex.org/)
+::   - Install Roboto font from MiKTeX Console
 ::
 
 set TOOLS=..\..\Tools
@@ -11,20 +15,18 @@ set PATH=%TOOLS%\gpp;%PATH%
 
 if not "%1"=="" (call :GenDoc %1 & goto :eof)
 
-call :GenDoc ReadMe
-call :GenDoc UserGuide
-call :GenDoc SystemGuide
-call :GenDoc Applications
-call :GenDoc ROM_Applications
-call :GenDoc Catalog
-call :GenDoc Errata
+call :GenDoc ReadMe || exit /b
+call :GenDoc UserGuide || exit /b
+call :GenDoc SystemGuide || exit /b
+call :GenDoc Applications || exit /b
+call :GenDoc Catalog || exit /b
+call :GenDoc Errata || exit /b
 
 if exist ReadMe.gfm copy Readme.gfm ..\..\ReadMe.md || exit /b
 if exist ReadMe.txt copy ReadMe.txt ..\..\ReadMe.txt || exit /b
 if exist UserGuide.pdf copy UserGuide.pdf "..\..\Doc\RomWBW User Guide.pdf" || exit /b
 if exist SystemGuide.pdf copy SystemGuide.pdf "..\..\Doc\RomWBW System Guide.pdf" || exit /b
 if exist Applications.pdf copy Applications.pdf "..\..\Doc\RomWBW Applications.pdf" || exit /b
-if exist ROM_Applications.pdf copy ROM_Applications.pdf "..\..\Doc\RomWBW ROM Applications.pdf" || exit /b
 if exist Catalog.pdf copy Catalog.pdf "..\..\Doc\RomWBW Disk Catalog.pdf" || exit /b
 if exist Errata.pdf copy Errata.pdf "..\..\Doc\RomWBW Errata.pdf" || exit /b
 
@@ -37,9 +39,6 @@ echo.
 
 echo Processing document %1...
 
-::gpp -o %1.tmp %1.md
-::gpp -o %1.tmp -U "\\" "" "{" "}{" "}" "{" "}" "#" "" %1.md
-::gpp -o %1.tmp -U "" "" "(" "," ")" "(" ")" "#" "" -M "#" "\n" " " " " "\n" "(" ")" %1.md
 gpp -o %1.tmp -U "$" "$" "{" "}{" "}$" "{" "}" "@@@" "" -M "$" "$" "{" "}{" "}$" "{" "}" %1.md || exit /b
 
 ::pandoc %1.tmp -f markdown -t latex -s -o %1.tex --default-image-extension=pdf || exit /b

Source/Doc/Catalog.md

@@ -217,9 +217,9 @@ on using the applications and files listed.
 | `INITDIR.COM`  | ZSDOS      | ZSDOS Prepare disks for P2DOS Stamps |
 | `KERMIT.COM`   |     --     | Generic CP/M 2.2 Kermit communication application |
 | `LBREXT.COM`   |     --     | Extract library files |
-| `LDDS.COM`     | ZSDOS      | Clock driver |
-| `LDNZT.COM`    | ZSDOS      | Clock driver |
-| `LDP2D.COM`    | ZSDOS      | Clock driver |
+| `LDDS.COM`     | ZSDOS      | Load DateStamper date/time stamping resident extension |
+| `LDNZT.COM`    | ZSDOS      | Load NZT date/time stamping resident extension |
+| `LDP2D.COM`    | ZSDOS      | Load P2DOS date/time stamping resident extension |
 | `LIB.COM`      |     --     | DRI Library manager |
 | `LINK.COM`     |     --     | DRI CPM relocatable linker |
 | `LOAD.COM`     |     --     | DRI hex file loader into memory |
@@ -229,7 +229,7 @@ on using the applications and files listed.
 | `PMARC.COM`    |     --     | LHA file compressor |
 | `PMEXT.COM`    |     --     | Extractor for PMARC archives |
 | `PUTBG.COM`    | ZSDOS      | ZSDOS Prepare disk for backgrounder |
-| `PUTDS.COM`    | ZSDOS      | ZSDOS Prepare disk for datestamper |
+| `PUTDS.COM`    | ZSDOS      | ZSDOS Prepare disk for datestamper date/time stamping|
 | `RELOG.COM`    | ZSDOS      | ZSDOS relog disks after program that bypasses BDOS |
 | `RMAC.COM`     |     --     | DRI Relocatable Macro Assembler |
 | `SETTERM.COM`  | ZSDOS      | ZSDOS Installs terminal control codes into DateSamper utilities |

Source/Doc/Graphics/BankSwitchedMemory.svg

@@ -0,0 +1,366 @@
+<?xml version="1.0" encoding="UTF-8" standalone="no"?>
+<!DOCTYPE svg PUBLIC "-//W3C//DTD SVG 1.1//EN" "http://www.w3.org/Graphics/SVG/1.1/DTD/svg11.dtd">
+<!-- Generated by Microsoft Visio, SVG Export BankSwitchedMemory.svg Page-1 -->
+<svg xmlns="http://www.w3.org/2000/svg" xmlns:xlink="http://www.w3.org/1999/xlink" xmlns:ev="http://www.w3.org/2001/xml-events"
+		width="6.51042in" height="5.73361in" viewBox="0 0 468.75 412.82" xml:space="preserve" color-interpolation-filters="sRGB"
+		class="st22">
+	<style type="text/css">
+	<![CDATA[
+		.st1 {fill:#c0c0c0;stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.24}
+		.st2 {fill:#ffffff;stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.24}
+		.st3 {stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.24}
+		.st4 {fill:#ffffff;stroke:none;stroke-linecap:butt;stroke-width:7.2}
+		.st5 {fill:#000000;font-family:Calibri;font-size:0.75em}
+		.st6 {fill:#ffffff;stroke:none;stroke-linecap:butt}
+		.st7 {fill:#000000;font-family:Calibri;font-size:1.00001em}
+		.st8 {fill:none;stroke:none;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.75}
+		.st9 {fill:#000000;font-family:Calibri;font-size:0.833336em}
+		.st10 {font-size:1em}
+		.st11 {stroke:#000000;stroke-dasharray:7,5;stroke-linecap:round;stroke-linejoin:round;stroke-width:1}
+		.st12 {fill:#ffffff;stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:1.5}
+		.st13 {stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:1.5}
+		.st14 {marker-end:url(#mrkr4-136);stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:1.5}
+		.st15 {fill:#000000;fill-opacity:1;stroke:#000000;stroke-opacity:1;stroke-width:0.37313432835821}
+		.st16 {fill:#000000;font-family:Calibri;font-size:0.666664em}
+		.st17 {stroke:#000000;stroke-dasharray:1.5,3;stroke-linecap:round;stroke-linejoin:round;stroke-width:1.5}
+		.st18 {marker-end:url(#mrkr4-165);marker-start:url(#mrkr10-163);stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.24}
+		.st19 {fill:#000000;fill-opacity:1;stroke:#000000;stroke-opacity:1;stroke-width:0.08695652173913}
+		.st20 {marker-end:url(#mrkr4-136);marker-start:url(#mrkr10-193);stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:1.5}
+		.st21 {fill:#ffffff;stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:1}
+		.st22 {fill:none;fill-rule:evenodd;font-size:12px;overflow:visible;stroke-linecap:square;stroke-miterlimit:3}
+	]]>
+	</style>
+
+	<defs id="Markers">
+		<g id="lend4">
+			<path d="M 2 1 L 0 0 L 2 -1 L 2 1 " style="stroke:none"/>
+		</g>
+		<marker id="mrkr4-136" class="st15" refX="-5.36" orient="auto" markerUnits="strokeWidth" overflow="visible">
+			<use xlink:href="#lend4" transform="scale(-2.68,-2.68) "/>
+		</marker>
+		<g id="lend10">
+			<path
+					d="M 0 0.75 C -0.414214 0.75 -0.75 0.414214 -0.75 0 -0.75 -0.414214 -0.414214 -0.75 0 -0.75 0.414214 -0.75 0.75 -0.414214 0.75 0 0.75 0.414214 0.414214 0.75 0 0.75 Z "
+					style="stroke:none"/>
+		</g>
+		<marker id="mrkr10-163" class="st19" refX="7.125" orient="auto" markerUnits="strokeWidth" overflow="visible">
+			<use xlink:href="#lend10" transform="scale(11.5) "/>
+		</marker>
+		<marker id="mrkr4-165" class="st19" refX="-23" orient="auto" markerUnits="strokeWidth" overflow="visible">
+			<use xlink:href="#lend4" transform="scale(-11.5,-11.5) "/>
+		</marker>
+		<marker id="mrkr10-193" class="st15" refX="1.77" orient="auto" markerUnits="strokeWidth" overflow="visible">
+			<use xlink:href="#lend10" transform="scale(2.68) "/>
+		</marker>
+	</defs>
+	<g>
+		<title>Page-1</title>
+		<g id="group13-1" transform="translate(216.75,-109.92)">
+			<title>Data block.13</title>
+			<g id="shape14-2" transform="translate(157.745,0)">
+				<title>Sheet.14</title>
+				<path d="M0 412.82 L11.41 401.41 L11.41 228.61 L0 240.02 L0 412.82 Z" class="st1"/>
+			</g>
+			<g id="shape15-4" transform="translate(0,-172.8)">
+				<title>Sheet.15</title>
+				<path d="M0 412.82 L157.75 412.82 L169.15 401.41 L11.41 401.41 L0 412.82 Z" class="st1"/>
+			</g>
+			<g id="shape16-6">
+				<title>Sheet.16</title>
+				<rect x="0" y="240.02" width="157.745" height="172.8" class="st2"/>
+			</g>
+		</g>
+		<g id="group9-8" transform="translate(216.75,-282.72)">
+			<title>Data block.9</title>
+			<g id="shape10-9" transform="translate(157.745,0)">
+				<title>Sheet.10</title>
+				<path d="M0 412.82 L11.41 401.41 L11.41 343.81 L0 355.22 L0 412.82 Z" class="st1"/>
+			</g>
+			<g id="shape11-11" transform="translate(0,-57.6)">
+				<title>Sheet.11</title>
+				<path d="M0 412.82 L157.75 412.82 L169.15 401.41 L11.41 401.41 L0 412.82 Z" class="st1"/>
+			</g>
+			<g id="shape12-13">
+				<title>Sheet.12</title>
+				<rect x="0" y="355.22" width="157.745" height="57.6" class="st2"/>
+			</g>
+		</g>
+		<g id="group5-15" transform="translate(216.75,-340.32)">
+			<title>Data block</title>
+			<g id="shape6-16" transform="translate(157.745,0)">
+				<title>Sheet.6</title>
+				<path d="M0 412.82 L11.41 401.41 L11.41 379.81 L0 391.22 L0 412.82 Z" class="st1"/>
+			</g>
+			<g id="shape7-18" transform="translate(0,-21.6)">
+				<title>Sheet.7</title>
+				<path d="M0 412.82 L157.75 412.82 L169.15 401.41 L11.41 401.41 L0 412.82 Z" class="st1"/>
+			</g>
+			<g id="shape8-20">
+				<title>Sheet.8</title>
+				<rect x="0" y="391.22" width="157.745" height="21.6" class="st2"/>
+			</g>
+		</g>
+		<g id="shape2-22" transform="translate(65.55,486.457) rotate(180)">
+			<title>Sheet.2</title>
+			<desc>$FE00</desc>
+			<path d="M0 412.82 L36 412.82" class="st3"/>
+			<rect x="-29.1072" y="-418.22" width="22.2144" height="10.7998" transform="rotate(180)" class="st4"/>
+			<text x="-29.11" y="-410.12" transform="rotate(180)" class="st5">$FE00</text>		</g>
+		<g id="shape3-27" transform="translate(65.55,542.541) rotate(180)">
+			<title>Sheet.3</title>
+			<desc>$D000</desc>
+			<path d="M0 412.82 L36 412.82" class="st3"/>
+			<rect x="-29.8916" y="-418.22" width="23.7832" height="10.7998" transform="rotate(180)" class="st6"/>
+			<text x="-29.89" y="-410.12" transform="rotate(180)" class="st5">$D000</text>		</g>
+		<g id="shape17-32" transform="translate(433.37,106.7) rotate(90)">
+			<title>Sheet.17</title>
+			<desc>$8000</desc>
+			<path d="M0 412.82 L46.25 412.82" class="st3"/>
+			<rect x="-38.3323" y="-420.02" width="30.4102" height="14.4001" transform="rotate(180)" class="st6"/>
+			<text x="-38.33" y="-409.22" transform="rotate(180)" class="st7">$8000</text>		</g>
+		<g id="group18-37" transform="translate(297.405,-282.72)">
+			<title>3D stack middle</title>
+			<g id="shape19-38" transform="translate(77.0909,0)">
+				<title>Sheet.19</title>
+				<path d="M0 412.82 L7.2 405.62 L7.2 387.58 L0 394.78 L0 412.82 Z" class="st1"/>
+			</g>
+			<g id="shape20-40">
+				<title>Sheet.20</title>
+				<rect x="0" y="394.784" width="77.0909" height="18.0364" class="st2"/>
+			</g>
+		</g>
+		<g id="group21-42" transform="translate(297.405,-297.12)">
+			<title>3D stack middle.21</title>
+			<g id="shape22-43" transform="translate(77.0909,0)">
+				<title>Sheet.22</title>
+				<path d="M0 412.82 L7.2 405.62 L7.2 384.02 L0 391.22 L0 412.82 Z" class="st1"/>
+			</g>
+			<g id="shape23-45">
+				<title>Sheet.23</title>
+				<rect x="0" y="391.22" width="77.0909" height="21.6" class="st2"/>
+			</g>
+		</g>
+		<g id="group24-47" transform="translate(297.405,-318.72)">
+			<title>3D stack middle.24</title>
+			<g id="shape25-48" transform="translate(77.0909,0)">
+				<title>Sheet.25</title>
+				<path d="M0 412.82 L7.2 405.62 L7.2 384.02 L0 391.22 L0 412.82 Z" class="st1"/>
+			</g>
+			<g id="shape26-50">
+				<title>Sheet.26</title>
+				<rect x="0" y="391.22" width="77.0909" height="21.6" class="st2"/>
+			</g>
+		</g>
+		<g id="shape27-52" transform="translate(220.314,-340.32)">
+			<title>Sheet.27</title>
+			<desc>HBIOS Proxy (RST 08)</desc>
+			<rect x="0" y="391.22" width="154.182" height="21.6" class="st8"/>
+			<text x="34.06" y="405.02" class="st9">HBIOS Proxy (RST 08)</text>		</g>
+		<g id="shape28-55" transform="translate(220.314,-109.92)">
+			<title>Sheet.28</title>
+			<desc>Application Area (TPA)</desc>
+			<rect x="0" y="237.402" width="154.836" height="175.418" class="st8"/>
+			<text x="22.5" y="328.71" class="st7">Application Area (TPA)</text>		</g>
+		<g id="shape29-58" transform="translate(220.314,-282.72)">
+			<title>Sheet.29</title>
+			<desc>Operating System CP/M or ZSYS</desc>
+			<rect x="0" y="355.22" width="77.0909" height="57.6" class="st8"/>
+			<text x="2.38" y="375.02" class="st9">Operating System  <tspan x="11.08" dy="2.4em" class="st10">CP/M or ZSYS</tspan></text>		</g>
+		<g id="shape30-62" transform="translate(297.405,-318.72)">
+			<title>Sheet.30</title>
+			<desc>CBIOS</desc>
+			<rect x="0" y="391.22" width="77.0909" height="21.6" class="st8"/>
+			<text x="26.29" y="405.02" class="st9">CBIOS</text>		</g>
+		<g id="shape31-65" transform="translate(297.405,-297.12)">
+			<title>Sheet.31</title>
+			<desc>BDOS</desc>
+			<rect x="0" y="391.22" width="77.0909" height="21.6" class="st8"/>
+			<text x="27.14" y="405.02" class="st9">BDOS</text>		</g>
+		<g id="shape32-68" transform="translate(297.405,-282.72)">
+			<title>Sheet.32</title>
+			<desc>CCP</desc>
+			<rect x="0" y="398.42" width="77.0909" height="14.4" class="st8"/>
+			<text x="30.63" y="408.62" class="st9">CCP</text>		</g>
+		<g id="group33-71" transform="translate(72.75,-109.92)">
+			<title>Data block.33</title>
+			<g id="shape34-72" transform="translate(108,0)">
+				<title>Sheet.34</title>
+				<path d="M0 412.82 L11.41 401.41 L11.41 286.21 L0 297.62 L0 412.82 Z" class="st1"/>
+			</g>
+			<g id="shape35-74" transform="translate(0,-115.2)">
+				<title>Sheet.35</title>
+				<path d="M0 412.82 L108 412.82 L119.41 401.41 L11.41 401.41 L0 412.82 Z" class="st1"/>
+			</g>
+			<g id="shape36-76">
+				<title>Sheet.36</title>
+				<rect x="0" y="297.62" width="108" height="115.2" class="st2"/>
+			</g>
+		</g>
+		<g id="shape37-78" transform="translate(22.35,-225.12)">
+			<title>Sheet.37</title>
+			<path d="M0 412.82 L360 412.82" class="st11"/>
+		</g>
+		<g id="shape38-81" transform="translate(72.75,-109.92)">
+			<title>Sheet.38</title>
+			<desc>HBIOS (Hardware Drivers)</desc>
+			<rect x="0" y="297.62" width="108" height="115.2" class="st8"/>
+			<text x="38.76" y="351.62" class="st7">HBIOS <tspan x="7.61" dy="1.2em" class="st10">(Hardware Drivers)</tspan></text>		</g>
+		<g id="shape39-85" transform="translate(22.35,-109.92)">
+			<title>Sheet.39</title>
+			<path d="M0 412.82 L338.4 412.82" class="st11"/>
+		</g>
+		<g id="shape40-88" transform="translate(22.35,-361.92)">
+			<title>Sheet.40</title>
+			<path d="M0 412.82 L360 412.82" class="st11"/>
+		</g>
+		<g id="shape43-91" transform="translate(-397.67,302.9) rotate(-90)">
+			<title>Sheet.43</title>
+			<desc>Z80 CPU Address Space</desc>
+			<rect x="0" y="398.42" width="252" height="14.4" class="st12"/>
+			<text x="69.04" y="409.22" class="st7">Z80 CPU Address Space</text>		</g>
+		<g id="shape41-94" transform="translate(-383.27,302.9) rotate(-90)">
+			<title>Sheet.41</title>
+			<desc>Banked Lower 32K</desc>
+			<rect x="0" y="398.42" width="115.2" height="14.4" class="st12"/>
+			<text x="12.48" y="409.22" class="st7">Banked Lower 32K</text>		</g>
+		<g id="shape42-97" transform="translate(-383.27,187.7) rotate(-90)">
+			<title>Sheet.42</title>
+			<desc>Fixed Upper 32K</desc>
+			<rect x="0" y="398.42" width="136.8" height="14.4" class="st12"/>
+			<text x="28.39" y="409.22" class="st7">Fixed Upper 32K</text>		</g>
+		<g id="shape1-100" transform="translate(65.55,463.72) rotate(180)">
+			<title>Sheet.1</title>
+			<desc>$10000</desc>
+			<path d="M0 412.82 L36 412.82" class="st3"/>
+			<rect x="-31.6846" y="-418.22" width="27.3691" height="10.7998" transform="rotate(180)" class="st6"/>
+			<text x="-31.68" y="-410.12" transform="rotate(180)" class="st5">$10000</text>		</g>
+		<g id="shape4-105" transform="translate(65.55,715.72) rotate(180)">
+			<title>Sheet.4</title>
+			<desc>$0000</desc>
+			<path d="M0 412.82 L36 412.82" class="st3"/>
+			<rect x="-29.4038" y="-418.22" width="22.8076" height="10.7998" transform="rotate(180)" class="st4"/>
+			<text x="-29.4" y="-410.12" transform="rotate(180)" class="st5">$0000</text>		</g>
+		<g id="shape44-110" transform="translate(798.77,50.9) rotate(90)">
+			<title>Bracket</title>
+			<path d="M0 412.82 A6.11239 6.11239 0 0 1 5.4 407.42 L64.22 407.42 A6.11239 6.11239 -180 0 0 69.62 402.02 A6.11239 6.11239
+						 -180 0 0 75.02 407.42 L131.4 407.42 A6.11239 6.11239 0 0 1 136.8 412.82" class="st13"/>
+		</g>
+		<g id="shape45-113" transform="translate(0.750002,-52.32)">
+			<title>Sheet.45</title>
+			<desc>Bank 0</desc>
+			<rect x="0" y="398.42" width="36" height="14.4" class="st12"/>
+			<text x="5.69" y="408.32" class="st5">Bank 0</text>		</g>
+		<g id="shape47-116" transform="translate(252.75,-52.32)">
+			<title>Sheet.47</title>
+			<desc>App/OS Banks</desc>
+			<rect x="0" y="398.42" width="108" height="14.4" class="st12"/>
+			<text x="28.09" y="408.32" class="st5">App/OS Banks</text>		</g>
+		<g id="shape48-119" transform="translate(360.75,-52.32)">
+			<title>Sheet.48</title>
+			<desc>Bank N-1</desc>
+			<rect x="0" y="398.42" width="36" height="14.4" class="st12"/>
+			<text x="1.41" y="408.32" class="st5">Bank N-1</text>		</g>
+		<g id="shape49-122" transform="translate(396.75,-52.32)">
+			<title>Sheet.49</title>
+			<desc>Bank N</desc>
+			<rect x="0" y="398.42" width="36" height="14.4" class="st12"/>
+			<text x="5.06" y="408.32" class="st5">Bank N</text>		</g>
+		<g id="shape50-125" transform="translate(36.75,-52.32)">
+			<title>Sheet.50</title>
+			<desc>• • •</desc>
+			<rect x="0" y="398.42" width="216" height="14.4" class="st12"/>
+			<text x="91.49" y="408.62" class="st9">•    •    •</text>		</g>
+		<g id="shape51-128" transform="translate(375.15,715.72) rotate(180)">
+			<title>Bracket.51</title>
+			<path d="M0 412.82 A8.14985 8.14985 0 0 1 7.2 405.62 L36 405.62 A8.14985 8.14985 -180 0 0 43.2 398.42 A8.14985 8.14985
+						 -180 0 0 50.4 405.62 L151.2 405.62 A8.14985 8.14985 0 0 1 158.4 412.82" class="st13"/>
+		</g>
+		<g id="shape55-131" transform="translate(396.75,-66.72)">
+			<title>Sheet.55</title>
+			<path d="M0 187.31 L9 187.31 A9 9 0 0 1 18 196.31 L18 404.78" class="st14"/>
+		</g>
+		<g id="shape56-137" transform="translate(0.750002,-37.92)">
+			<title>Sheet.56</title>
+			<desc>Physical RAM (32K per bank)</desc>
+			<rect x="0" y="398.42" width="432" height="14.4" class="st12"/>
+			<text x="157.88" y="408.62" class="st9">Physical RAM (32K per bank)</text>		</g>
+		<g id="shape57-140" transform="translate(180.75,715.72) rotate(180)">
+			<title>Bracket.57</title>
+			<desc>`</desc>
+			<path d="M0 412.82 A8.14984 8.14984 0 0 1 7.2 405.62 L46.8 405.62 A8.14984 8.14984 -180 0 0 54 398.42 A8.14984 8.14984
+						 -180 0 0 61.2 405.62 L100.8 405.62 A8.14984 8.14984 0 0 1 108 412.82" class="st13"/>
+			<rect x="393.092" y="-58.7999" width="2.328" height="9.59985" transform="rotate(90)" class="st4"/>
+			<text x="393.09" y="-51.6" transform="rotate(90)" class="st16">`</text>		</g>
+		<g id="shape58-145" transform="translate(449.57,360.5) rotate(90)">
+			<title>Sheet.58</title>
+			<path d="M0 412.82 L34.16 412.82" class="st17"/>
+		</g>
+		<g id="group60-148" transform="translate(36.75,-0.12)">
+			<title>3D stack top</title>
+			<desc>RAM Disk</desc>
+			<g id="shape61-149" transform="translate(208.8,0)">
+				<title>Sheet.61</title>
+				<path d="M0 412.82 L7.09 405.73 L7.09 387.73 L0 394.82 L0 412.82 Z" class="st1"/>
+			</g>
+			<g id="shape62-151" transform="translate(0,-18)">
+				<title>Sheet.62</title>
+				<path d="M0 412.82 L208.8 412.82 L215.89 405.73 L7.09 405.73 L0 412.82 Z" class="st1"/>
+			</g>
+			<g id="shape63-153">
+				<title>Sheet.63</title>
+				<rect x="0" y="394.82" width="208.8" height="18" class="st2"/>
+			</g>
+			<g id="shape60-155">
+				<text x="88.83" y="406.22" class="st16">RAM Disk</text>			</g>
+		</g>
+		<g id="shape64-157" transform="translate(-59.27,84.02) rotate(-90)">
+			<title>Pointer (1-D)</title>
+			<path d="M1.71 412.82 L2.07 412.82 L16.08 412.82" class="st18"/>
+		</g>
+		<g id="shape65-166" transform="translate(-95.27,108.5) rotate(-90)">
+			<title>Pointer (1-D).65</title>
+			<path d="M1.71 412.82 L2.07 412.82 L18.96 412.82" class="st18"/>
+		</g>
+		<g id="shape66-173" transform="translate(-52.07,122.9) rotate(-90)">
+			<title>Pointer (1-D).66</title>
+			<path d="M1.71 412.82 L2.07 412.82 L11.76 412.82" class="st18"/>
+		</g>
+		<g id="shape67-180" transform="translate(-105.35,137.3) rotate(-90)">
+			<title>Pointer (1-D).67</title>
+			<path d="M1.71 412.82 L2.07 412.82 L26.16 412.82" class="st18"/>
+		</g>
+		<g id="shape70-187" transform="translate(228.935,-227.945) scale(-1,1)">
+			<title>Sheet.70</title>
+			<path d="M2.65 293.24 L3.01 293.24 L76.08 293.24 A22.5 22.5 0 0 1 98.58 315.74 L98.58 404.78" class="st20"/>
+		</g>
+		<g id="shape68-195" transform="translate(87.15,-289.92)">
+			<title>Sheet.68</title>
+			<desc>HBIOS Function Call w/ Bank Switch</desc>
+			<rect x="0" y="384.02" width="86.4" height="28.8" class="st2"/>
+			<text x="7.14" y="395.72" class="st5">HBIOS Function Call <tspan x="15.11" dy="1.2em" class="st10">w/ Bank Switch</tspan></text>		</g>
+		<g id="shape69-199" transform="translate(0.75,-390.72)">
+			<title>Sheet.69</title>
+			<desc>RomWBW Bank Switched Memory Layout</desc>
+			<rect x="0" y="391.22" width="432" height="21.6" class="st21"/>
+			<text x="113.82" y="405.62" class="st7">RomWBW Bank Switched Memory Layout</text>		</g>
+		<g id="shape59-202" transform="translate(665.566,362.226) rotate(90.2396)">
+			<title>Sheet.59</title>
+			<path d="M0 412.82 L27.11 412.82" class="st17"/>
+		</g>
+		<g id="shape52-205" transform="translate(16.33,324.5) rotate(-90)">
+			<title>Sheet.52</title>
+			<desc>Fixed Mapping of Upper 32K to Last Bank</desc>
+			<rect x="0" y="398.42" width="172.8" height="14.4" class="st8"/>
+			<text x="11.1" y="408.32" class="st5">Fixed Mapping of Upper 32K to Last Bank</text>		</g>
+		<g id="shape72-208" transform="translate(331.95,-66.72)">
+			<title>Sheet.72</title>
+			<path d="M0 384.02 L0 387.62 A3.59999 3.59999 -180 0 0 3.6 391.22 L45.4 391.22 A5 5 0 0 1 50.4 396.22 L50.4 404.78"
+					class="st14"/>
+		</g>
+		<g id="shape74-213" transform="translate(126.75,-66.72) scale(-1,1)">
+			<title>Sheet.74</title>
+			<path d="M0 384.02 L0 387.62 A3.59999 3.59999 -180 0 0 3.6 391.22 L103 391.22 A5 5 0 0 1 108 396.22 L108 404.78"
+					class="st14"/>
+		</g>
+	</g>
+</svg>

Source/Doc/Graphics/CharacterEmulationVideoServices.svg

@@ -0,0 +1,830 @@
+<?xml version="1.0" encoding="UTF-8" standalone="no"?>
+<!DOCTYPE svg PUBLIC "-//W3C//DTD SVG 1.1//EN" "http://www.w3.org/Graphics/SVG/1.1/DTD/svg11.dtd">
+<!-- Generated by Microsoft Visio, SVG Export CharacterEmulationVideoServices.svg Page-1 -->
+<svg xmlns="http://www.w3.org/2000/svg" xmlns:xlink="http://www.w3.org/1999/xlink" xmlns:ev="http://www.w3.org/2001/xml-events"
+		width="6.01042in" height="5.76042in" viewBox="0 0 432.75 414.75" xml:space="preserve" color-interpolation-filters="sRGB"
+		class="st16">
+	<style type="text/css">
+	<![CDATA[
+		.st1 {fill:#ffffff;stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.75}
+		.st2 {fill:#000000;font-family:Calibri;font-size:0.833336em;font-weight:bold}
+		.st3 {font-size:1em}
+		.st4 {marker-end:url(#mrkr13-15);stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.75}
+		.st5 {fill:#000000;fill-opacity:1;stroke:#000000;stroke-opacity:1;stroke-width:0.22935779816514}
+		.st6 {fill:#a5a5a5;stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.75}
+		.st7 {fill:#000000;font-family:Calibri;font-size:0.666664em;font-weight:bold}
+		.st8 {fill:#ffffff;stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.24}
+		.st9 {fill:#00ff00;stroke:none;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.75}
+		.st10 {fill:#e6e6e6;stroke:none;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.75}
+		.st11 {fill:#b3b3b3;stroke:none;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.75}
+		.st12 {fill:none;stroke:none;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.75}
+		.st13 {fill:#ffffff;stroke:#000000;stroke-dasharray:0.75,1.5;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.75}
+		.st14 {fill:#000000;font-family:Calibri;font-size:0.499992em;font-weight:bold}
+		.st15 {fill:#000000;font-family:Calibri;font-size:1.16666em;font-weight:bold}
+		.st16 {fill:none;fill-rule:evenodd;font-size:12px;overflow:visible;stroke-linecap:square;stroke-miterlimit:3}
+	]]>
+	</style>
+
+	<defs id="Markers">
+		<g id="lend13">
+			<path d="M 3 1 L 0 0 L 3 -1 L 3 1 " style="stroke:none"/>
+		</g>
+		<marker id="mrkr13-15" class="st5" refX="-13.08" orient="auto" markerUnits="strokeWidth" overflow="visible">
+			<use xlink:href="#lend13" transform="scale(-4.36,-4.36) "/>
+		</marker>
+	</defs>
+	<g>
+		<title>Page-1</title>
+		<g id="shape81-1" transform="translate(17.625,414.375) rotate(-90)">
+			<title>Sheet.81</title>
+			<rect x="0" y="279.75" width="360" height="135" class="st1"/>
+		</g>
+		<g id="shape80-3" transform="translate(-135.375,414.375) rotate(-90)">
+			<title>Sheet.80</title>
+			<rect x="0" y="189.75" width="360" height="225" class="st1"/>
+		</g>
+		<g id="shape1-5" transform="translate(108.539,-315.375)">
+			<title>Sheet.1</title>
+			<desc>Character I/O Services</desc>
+			<rect x="0" y="378.75" width="53.8364" height="36" class="st1"/>
+			<text x="6.75" y="387.75" class="st2">Character <tspan x="20.06" dy="1.2em" class="st3">I/O </tspan><tspan x="10.06"
+						dy="1.2em" class="st3">Services</tspan></text>		</g>
+		<g id="shape2-10" transform="translate(36.375,-333.375)">
+			<title>Sheet.2</title>
+			<path d="M0 414.75 L62.35 414.75" class="st4"/>
+		</g>
+		<g id="shape8-16" transform="translate(550.125,153.375) rotate(90)">
+			<title>Sheet.8</title>
+			<path d="M0 414.75 L17.19 414.75" class="st4"/>
+		</g>
+		<g id="shape9-21" transform="translate(108.375,-189.375)">
+			<title>Sheet.9</title>
+			<desc>Emulation Services</desc>
+			<rect x="0" y="369.75" width="54" height="45" class="st1"/>
+			<text x="5.78" y="389.25" class="st2">Emulation <tspan x="10.14" dy="1.2em" class="st3">Services</tspan></text>		</g>
+		<g id="shape10-25" transform="translate(108.375,-171.375)">
+			<title>Sheet.10</title>
+			<desc>TTY</desc>
+			<rect x="0" y="396.75" width="54" height="18" class="st1"/>
+			<text x="19.45" y="408.75" class="st2">TTY</text>		</g>
+		<g id="shape11-28" transform="translate(108.375,-153.375)">
+			<title>Sheet.11</title>
+			<desc>ANSI</desc>
+			<rect x="0" y="396.75" width="54" height="18" class="st1"/>
+			<text x="16.98" y="408.75" class="st2">ANSI</text>		</g>
+		<g id="shape12-31" transform="translate(162.211,-180.375)">
+			<title>Sheet.12</title>
+			<path d="M0 414.75 L17.35 414.75" class="st4"/>
+		</g>
+		<g id="shape13-36" transform="translate(162.211,-162.375)">
+			<title>Sheet.13</title>
+			<path d="M0 414.75 L17.35 414.75" class="st4"/>
+		</g>
+		<g id="shape14-41" transform="translate(189.375,-99.375)">
+			<title>Sheet.14</title>
+			<desc>Video Display Adapter Services</desc>
+			<rect x="0" y="324.75" width="54" height="90" class="st1"/>
+			<text x="14.93" y="354.75" class="st2">Video <tspan x="11.88" dy="1.2em" class="st3">Display </tspan><tspan x="10.11"
+						dy="1.2em" class="st3">Adapter </tspan><tspan x="10.14" dy="1.2em" class="st3">Services</tspan></text>		</g>
+		<g id="shape18-47" transform="translate(243.375,-36.375)">
+			<title>Sheet.18</title>
+			<path d="M0 414.75 L62.19 414.75" class="st4"/>
+		</g>
+		<g id="shape27-52" transform="translate(315.375,-315.375)">
+			<title>Sheet.27</title>
+			<desc>UART</desc>
+			<rect x="0" y="396.75" width="44.9182" height="18" class="st6"/>
+			<text x="13.19" y="408.15" class="st7">UART</text>		</g>
+		<g id="shape34-55" transform="translate(314.311,-261.375)">
+			<title>Sheet.34</title>
+			<desc>ASCI</desc>
+			<rect x="0" y="396.75" width="44.9182" height="18" class="st6"/>
+			<text x="14.96" y="408.15" class="st7">ASCI</text>		</g>
+		<g id="group20-58" transform="translate(396.375,-94.875)">
+			<title>Terminal.20</title>
+			<g id="shape36-59" transform="translate(-391.186,414.75) rotate(-90)">
+				<title>Sheet.36</title>
+				<path d="M0 414.75 L27 414.75 L27 409.08 L0 409.08 L0 414.75 ZM26.25 403.93 L23.44 399.37 L3.53 399.37 L0.75 403.93
+							 L26.25 403.93 ZM23.44 399.37 L23.44 391.19 L3.53 391.19 L3.53 399.37 L23.44 399.37 ZM26.25 407.7 L26.25
+							 403.93 L0.75 403.93 L0.75 407.7 L26.25 407.7 ZM24.83 407.7 A1223.48 394.162 90 0 1 2.17 407.7 L24.83
+							 407.7 Z" class="st8"/>
+			</g>
+			<g id="shape37-61" transform="translate(-395.768,392.25) rotate(-90)">
+				<title>Sheet.37</title>
+				<rect x="0" y="414.641" width="0.75" height="0.109091" class="st9"/>
+			</g>
+			<g id="shape38-63" transform="translate(-391.623,414.188) rotate(-90)">
+				<title>Sheet.38</title>
+				<path d="M1.69 410.93 L2.63 410.93 L2.63 410.39 L1.69 410.39 L1.69 410.93 ZM2.81 410.93 L3.75 410.93 L3.75 410.39
+							 L2.81 410.39 L2.81 410.93 ZM3.94 410.93 L4.87 410.93 L4.87 410.39 L3.94 410.39 L3.94 410.93 ZM5.06 410.93
+							 L6 410.93 L6 410.39 L5.06 410.39 L5.06 410.93 ZM12.28 410.93 L13.22 410.93 L13.22 410.39 L12.28 410.39
+							 L12.28 410.93 ZM13.41 410.93 L14.34 410.93 L14.34 410.39 L13.41 410.39 L13.41 410.93 ZM14.53 410.93
+							 L15.47 410.93 L15.47 410.39 L14.53 410.39 L14.53 410.93 ZM15.66 410.93 L16.59 410.93 L16.59 410.39 L15.66
+							 410.39 L15.66 410.93 ZM0 412.02 L1.5 412.02 L1.5 411.48 L0 411.48 L0 412.02 ZM1.69 412.02 L2.63 412.02
+							 L2.63 411.48 L1.69 411.48 L1.69 412.02 ZM2.81 412.02 L3.75 412.02 L3.75 411.48 L2.81 411.48 L2.81 412.02
+							 ZM3.94 412.02 L4.87 412.02 L4.87 411.48 L3.94 411.48 L3.94 412.02 ZM5.06 412.02 L6 412.02 L6 411.48
+							 L5.06 411.48 L5.06 412.02 ZM6.19 412.02 L7.12 412.02 L7.12 411.48 L6.19 411.48 L6.19 412.02 ZM7.31 412.02
+							 L8.25 412.02 L8.25 411.48 L7.31 411.48 L7.31 412.02 ZM8.44 412.02 L9.37 412.02 L9.37 411.48 L8.44 411.48
+							 L8.44 412.02 ZM9.56 412.02 L10.5 412.02 L10.5 411.48 L9.56 411.48 L9.56 412.02 ZM10.69 412.02 L11.62
+							 412.02 L11.62 411.48 L10.69 411.48 L10.69 412.02 ZM11.81 412.02 L12.75 412.02 L12.75 411.48 L11.81 411.48
+							 L11.81 412.02 ZM12.94 412.02 L13.87 412.02 L13.87 411.48 L12.94 411.48 L12.94 412.02 ZM14.06 412.02
+							 L15 412.02 L15 411.48 L14.06 411.48 L14.06 412.02 ZM1.69 412.7 L2.63 412.7 L2.63 412.16 L1.69 412.16
+							 L1.69 412.7 ZM2.81 412.7 L3.75 412.7 L3.75 412.16 L2.81 412.16 L2.81 412.7 ZM3.94 412.7 L4.87 412.7
+							 L4.87 412.16 L3.94 412.16 L3.94 412.7 ZM5.06 412.7 L6 412.7 L6 412.16 L5.06 412.16 L5.06 412.7 ZM6.19
+							 412.7 L7.12 412.7 L7.12 412.16 L6.19 412.16 L6.19 412.7 ZM7.31 412.7 L8.25 412.7 L8.25 412.16 L7.31
+							 412.16 L7.31 412.7 ZM8.44 412.7 L9.37 412.7 L9.37 412.16 L8.44 412.16 L8.44 412.7 ZM9.56 412.7 L10.5
+							 412.7 L10.5 412.16 L9.56 412.16 L9.56 412.7 ZM10.69 412.7 L11.62 412.7 L11.62 412.16 L10.69 412.16 L10.69
+							 412.7 ZM11.81 412.7 L12.75 412.7 L12.75 412.16 L11.81 412.16 L11.81 412.7 ZM12.94 412.7 L13.87 412.7
+							 L13.87 412.16 L12.94 412.16 L12.94 412.7 ZM14.06 412.7 L15 412.7 L15 412.16 L14.06 412.16 L14.06 412.7
+							 ZM1.69 413.39 L2.63 413.39 L2.63 412.84 L1.69 412.84 L1.69 413.39 ZM2.81 413.39 L3.75 413.39 L3.75 412.84
+							 L2.81 412.84 L2.81 413.39 ZM3.94 413.39 L4.87 413.39 L4.87 412.84 L3.94 412.84 L3.94 413.39 ZM5.06 413.39
+							 L6 413.39 L6 412.84 L5.06 412.84 L5.06 413.39 ZM6.19 413.39 L7.12 413.39 L7.12 412.84 L6.19 412.84 L6.19
+							 413.39 ZM7.31 413.39 L8.25 413.39 L8.25 412.84 L7.31 412.84 L7.31 413.39 ZM8.44 413.39 L9.37 413.39
+							 L9.37 412.84 L8.44 412.84 L8.44 413.39 ZM9.56 413.39 L10.5 413.39 L10.5 412.84 L9.56 412.84 L9.56 413.39
+							 ZM10.69 413.39 L11.62 413.39 L11.62 412.84 L10.69 412.84 L10.69 413.39 ZM11.81 413.39 L12.75 413.39
+							 L12.75 412.84 L11.81 412.84 L11.81 413.39 ZM12.94 413.39 L13.87 413.39 L13.87 412.84 L12.94 412.84 L12.94
+							 413.39 ZM14.06 413.39 L15 413.39 L15 412.84 L14.06 412.84 L14.06 413.39 ZM1.69 414.07 L2.63 414.07 L2.63
+							 413.52 L1.69 413.52 L1.69 414.07 ZM2.81 414.07 L3.75 414.07 L3.75 413.52 L2.81 413.52 L2.81 414.07 ZM3.94
+							 414.07 L4.87 414.07 L4.87 413.52 L3.94 413.52 L3.94 414.07 ZM5.06 414.07 L6 414.07 L6 413.52 L5.06 413.52
+							 L5.06 414.07 ZM6.19 414.07 L7.12 414.07 L7.12 413.52 L6.19 413.52 L6.19 414.07 ZM7.31 414.07 L8.25 414.07
+							 L8.25 413.52 L7.31 413.52 L7.31 414.07 ZM8.44 414.07 L9.37 414.07 L9.37 413.52 L8.44 413.52 L8.44 414.07
+							 ZM9.56 414.07 L10.5 414.07 L10.5 413.52 L9.56 413.52 L9.56 414.07 ZM10.69 414.07 L11.62 414.07 L11.62
+							 413.52 L10.69 413.52 L10.69 414.07 ZM11.81 414.07 L12.75 414.07 L12.75 413.52 L11.81 413.52 L11.81 414.07
+							 ZM12.94 414.07 L13.87 414.07 L13.87 413.52 L12.94 413.52 L12.94 414.07 ZM3.94 414.75 L11.62 414.75 L11.62
+							 414.2 L3.94 414.2 L3.94 414.75 ZM21 414.75 L23.25 414.75 L23.25 414.2 L21 414.2 L21 414.75 ZM23.44 414.75
+							 L24.37 414.75 L24.37 414.2 L23.44 414.2 L23.44 414.75 ZM23.44 414.07 L24.37 414.07 L24.37 413.52 L23.44
+							 413.52 L23.44 414.07 ZM22.22 414.07 L23.16 414.07 L23.16 413.52 L22.22 413.52 L22.22 414.07 ZM21 414.07
+							 L21.94 414.07 L21.94 413.52 L21 413.52 L21 414.07 ZM21 413.39 L21.94 413.39 L21.94 412.84 L21 412.84
+							 L21 413.39 ZM21 412.7 L21.94 412.7 L21.94 412.16 L21 412.16 L21 412.7 ZM22.22 412.7 L23.16 412.7 L23.16
+							 412.16 L22.22 412.16 L22.22 412.7 ZM23.44 412.7 L24.37 412.7 L24.37 412.16 L23.44 412.16 L23.44 412.7
+							 ZM23.44 413.39 L24.37 413.39 L24.37 412.84 L23.44 412.84 L23.44 413.39 ZM22.22 413.39 L23.16 413.39
+							 L23.16 412.84 L22.22 412.84 L22.22 413.39 Z" class="st10"/>
+			</g>
+			<g id="shape39-65" transform="translate(-391.623,414.188) rotate(-90)">
+				<title>Sheet.39</title>
+				<path d="M0 410.93 L0.94 410.93 L0.94 410.39 L0 410.39 L0 410.93 ZM0 412.7 L1.5 412.7 L1.5 412.16 L0 412.16 L0 412.7
+							 ZM0 413.39 L1.5 413.39 L1.5 412.84 L0 412.84 L0 413.39 ZM0 414.07 L1.5 414.07 L1.5 413.52 L0 413.52
+							 L0 414.07 ZM0 414.75 L1.5 414.75 L1.5 414.2 L0 414.2 L0 414.75 ZM1.69 414.75 L2.63 414.75 L2.63 414.2
+							 L1.69 414.2 L1.69 414.75 ZM2.81 414.75 L3.75 414.75 L3.75 414.2 L2.81 414.2 L2.81 414.75 ZM11.81 414.75
+							 L12.75 414.75 L12.75 414.2 L11.81 414.2 L11.81 414.75 ZM12.94 414.75 L13.87 414.75 L13.87 414.2 L12.94
+							 414.2 L12.94 414.75 ZM14.06 414.75 L15 414.75 L15 414.2 L14.06 414.2 L14.06 414.75 ZM15.19 414.75 L16.69
+							 414.75 L16.69 414.2 L15.19 414.2 L15.19 414.75 ZM17.25 414.75 L18.19 414.75 L18.19 414.2 L17.25 414.2
+							 L17.25 414.75 ZM18.37 414.75 L19.31 414.75 L19.31 414.2 L18.37 414.2 L18.37 414.75 ZM19.5 414.75 L20.44
+							 414.75 L20.44 414.2 L19.5 414.2 L19.5 414.75 ZM24.66 414.75 L25.59 414.75 L25.59 413.55 L24.66 413.55
+							 L24.66 414.75 ZM24.66 413.44 L25.59 413.44 L25.59 412.16 L24.66 412.16 L24.66 413.44 ZM24.66 412.02
+							 L25.59 412.02 L25.59 411.48 L24.66 411.48 L24.66 412.02 ZM23.44 412.02 L24.37 412.02 L24.37 411.48 L23.44
+							 411.48 L23.44 412.02 ZM22.22 412.02 L23.16 412.02 L23.16 411.48 L22.22 411.48 L22.22 412.02 ZM21 412.02
+							 L21.94 412.02 L21.94 411.48 L21 411.48 L21 412.02 ZM19.5 412.02 L20.44 412.02 L20.44 411.48 L19.5 411.48
+							 L19.5 412.02 ZM19.5 412.7 L20.44 412.7 L20.44 412.16 L19.5 412.16 L19.5 412.7 ZM18.37 414.07 L19.31
+							 414.07 L19.31 413.52 L18.37 413.52 L18.37 414.07 ZM14.06 414.06 L16.69 414.06 L16.69 413.51 L14.06 413.51
+							 L14.06 414.06 ZM15.19 413.37 L16.69 413.37 L16.69 412.17 L15.19 412.17 L15.19 413.37 ZM17.25 412.7 L18.19
+							 412.7 L18.19 412.16 L17.25 412.16 L17.25 412.7 ZM18.37 412.7 L19.31 412.7 L19.31 412.16 L18.37 412.16
+							 L18.37 412.7 ZM18.37 412.02 L19.31 412.02 L19.31 411.48 L18.37 411.48 L18.37 412.02 ZM15.19 412.02 L16.69
+							 412.02 L16.69 411.48 L15.19 411.48 L15.19 412.02 ZM24.19 410.6 L24.94 410.6 L24.94 410.5 L24.19 410.5
+							 L24.19 410.6 ZM23.06 410.6 L23.81 410.6 L23.81 410.5 L23.06 410.5 L23.06 410.6 ZM19.5 410.93 L20.44
+							 410.93 L20.44 410.39 L19.5 410.39 L19.5 410.93 ZM18.37 410.93 L19.31 410.93 L19.31 410.39 L18.37 410.39
+							 L18.37 410.93 ZM17.25 410.93 L18.19 410.93 L18.19 410.39 L17.25 410.39 L17.25 410.93 ZM10.31 410.93
+							 L11.25 410.93 L11.25 410.39 L10.31 410.39 L10.31 410.93 ZM9.19 410.93 L10.12 410.93 L10.12 410.39 L9.19
+							 410.39 L9.19 410.93 ZM8.06 410.93 L9 410.93 L9 410.39 L8.06 410.39 L8.06 410.93 ZM6.94 410.93 L7.87
+							 410.93 L7.87 410.39 L6.94 410.39 L6.94 410.93 ZM17.25 412.02 L18.19 412.02 L18.19 411.48 L17.25 411.48
+							 L17.25 412.02 Z" class="st11"/>
+			</g>
+		</g>
+		<g id="shape40-67" transform="translate(315.375,-99.375)">
+			<title>Sheet.40</title>
+			<desc>CVDU</desc>
+			<rect x="0" y="396.75" width="44.9182" height="18" class="st6"/>
+			<text x="12.84" y="408.15" class="st7">CVDU</text>		</g>
+		<g id="shape41-70" transform="translate(360.293,-108.375)">
+			<title>Sheet.41</title>
+			<path d="M0 414.75 L26.27 414.75" class="st4"/>
+		</g>
+		<g id="shape47-75" transform="translate(315.375,-63.375)">
+			<title>Sheet.47</title>
+			<desc>UPD7220</desc>
+			<rect x="0" y="396.75" width="44.9182" height="18" class="st6"/>
+			<text x="7.09" y="408.15" class="st7">UPD7220</text>		</g>
+		<g id="shape54-78" transform="translate(315.375,-27.375)">
+			<title>Sheet.54</title>
+			<desc>N8</desc>
+			<rect x="0" y="396.75" width="44.9182" height="18" class="st6"/>
+			<text x="17.8" y="408.15" class="st7">N8</text>		</g>
+		<g id="shape56-81" transform="translate(54.375,-333.375)">
+			<title>Sheet.56</title>
+			<desc>CIOXXX</desc>
+			<rect x="0" y="401.25" width="45" height="13.5" class="st12"/>
+			<text x="10" y="410.4" class="st7">CIOXXX</text>		</g>
+		<g id="shape57-84" transform="translate(54.375,-117.375)">
+			<title>Sheet.57</title>
+			<desc>VDAXXX</desc>
+			<rect x="0" y="401.25" width="45" height="13.5" class="st12"/>
+			<text x="8.58" y="410.4" class="st7">VDAXXX</text>		</g>
+		<g id="shape58-87" transform="translate(-378.375,414.375) rotate(-90)">
+			<title>Sheet.58</title>
+			<desc>Operating System / Utilities</desc>
+			<rect x="0" y="378.75" width="360" height="36" class="st1"/>
+			<text x="122.42" y="399.75" class="st2">Operating System / Utilities</text>		</g>
+		<g id="shape59-90" transform="translate(108.375,-135.375)">
+			<title>Sheet.59</title>
+			<desc>Others...</desc>
+			<path d="M0 414.75 L54 414.75 L54 396.75 L0 396.75 L0 414.75 Z" class="st13"/>
+			<text x="8.91" y="408.75" class="st2">Others...</text>		</g>
+		<g id="shape60-93" transform="translate(162.211,-144.375)">
+			<title>Sheet.60</title>
+			<path d="M0 414.75 L17.35 414.75" class="st4"/>
+		</g>
+		<g id="shape61-98" transform="translate(36.375,-211.875)">
+			<title>Sheet.61</title>
+			<path d="M0 414.75 L62.19 414.75" class="st4"/>
+		</g>
+		<g id="shape62-103" transform="translate(54.375,-211.875)">
+			<title>Sheet.62</title>
+			<desc>EMUXXX</desc>
+			<rect x="0" y="401.25" width="45" height="13.5" class="st12"/>
+			<text x="7.83" y="410.4" class="st7">EMUXXX</text>		</g>
+		<g id="shape15-106" transform="translate(36.375,-117.375)">
+			<title>Sheet.15</title>
+			<path d="M0 414.75 L143.19 414.75" class="st4"/>
+		</g>
+		<g id="group16-111" transform="translate(396.375,-58.875)">
+			<title>Terminal.16</title>
+			<g id="shape42-112" transform="translate(-391.186,414.75) rotate(-90)">
+				<title>Sheet.42</title>
+				<path d="M0 414.75 L27 414.75 L27 409.08 L0 409.08 L0 414.75 ZM26.25 403.93 L23.44 399.37 L3.53 399.37 L0.75 403.93
+							 L26.25 403.93 ZM23.44 399.37 L23.44 391.19 L3.53 391.19 L3.53 399.37 L23.44 399.37 ZM26.25 407.7 L26.25
+							 403.93 L0.75 403.93 L0.75 407.7 L26.25 407.7 ZM24.83 407.7 A1223.48 394.162 90 0 1 2.17 407.7 L24.83
+							 407.7 Z" class="st8"/>
+			</g>
+			<g id="shape43-114" transform="translate(-395.768,392.25) rotate(-90)">
+				<title>Sheet.43</title>
+				<rect x="0" y="414.641" width="0.75" height="0.109091" class="st9"/>
+			</g>
+			<g id="shape44-116" transform="translate(-391.623,414.188) rotate(-90)">
+				<title>Sheet.44</title>
+				<path d="M1.69 410.93 L2.63 410.93 L2.63 410.39 L1.69 410.39 L1.69 410.93 ZM2.81 410.93 L3.75 410.93 L3.75 410.39
+							 L2.81 410.39 L2.81 410.93 ZM3.94 410.93 L4.87 410.93 L4.87 410.39 L3.94 410.39 L3.94 410.93 ZM5.06 410.93
+							 L6 410.93 L6 410.39 L5.06 410.39 L5.06 410.93 ZM12.28 410.93 L13.22 410.93 L13.22 410.39 L12.28 410.39
+							 L12.28 410.93 ZM13.41 410.93 L14.34 410.93 L14.34 410.39 L13.41 410.39 L13.41 410.93 ZM14.53 410.93
+							 L15.47 410.93 L15.47 410.39 L14.53 410.39 L14.53 410.93 ZM15.66 410.93 L16.59 410.93 L16.59 410.39 L15.66
+							 410.39 L15.66 410.93 ZM0 412.02 L1.5 412.02 L1.5 411.48 L0 411.48 L0 412.02 ZM1.69 412.02 L2.63 412.02
+							 L2.63 411.48 L1.69 411.48 L1.69 412.02 ZM2.81 412.02 L3.75 412.02 L3.75 411.48 L2.81 411.48 L2.81 412.02
+							 ZM3.94 412.02 L4.87 412.02 L4.87 411.48 L3.94 411.48 L3.94 412.02 ZM5.06 412.02 L6 412.02 L6 411.48
+							 L5.06 411.48 L5.06 412.02 ZM6.19 412.02 L7.12 412.02 L7.12 411.48 L6.19 411.48 L6.19 412.02 ZM7.31 412.02
+							 L8.25 412.02 L8.25 411.48 L7.31 411.48 L7.31 412.02 ZM8.44 412.02 L9.37 412.02 L9.37 411.48 L8.44 411.48
+							 L8.44 412.02 ZM9.56 412.02 L10.5 412.02 L10.5 411.48 L9.56 411.48 L9.56 412.02 ZM10.69 412.02 L11.62
+							 412.02 L11.62 411.48 L10.69 411.48 L10.69 412.02 ZM11.81 412.02 L12.75 412.02 L12.75 411.48 L11.81 411.48
+							 L11.81 412.02 ZM12.94 412.02 L13.87 412.02 L13.87 411.48 L12.94 411.48 L12.94 412.02 ZM14.06 412.02
+							 L15 412.02 L15 411.48 L14.06 411.48 L14.06 412.02 ZM1.69 412.7 L2.63 412.7 L2.63 412.16 L1.69 412.16
+							 L1.69 412.7 ZM2.81 412.7 L3.75 412.7 L3.75 412.16 L2.81 412.16 L2.81 412.7 ZM3.94 412.7 L4.87 412.7
+							 L4.87 412.16 L3.94 412.16 L3.94 412.7 ZM5.06 412.7 L6 412.7 L6 412.16 L5.06 412.16 L5.06 412.7 ZM6.19
+							 412.7 L7.12 412.7 L7.12 412.16 L6.19 412.16 L6.19 412.7 ZM7.31 412.7 L8.25 412.7 L8.25 412.16 L7.31
+							 412.16 L7.31 412.7 ZM8.44 412.7 L9.37 412.7 L9.37 412.16 L8.44 412.16 L8.44 412.7 ZM9.56 412.7 L10.5
+							 412.7 L10.5 412.16 L9.56 412.16 L9.56 412.7 ZM10.69 412.7 L11.62 412.7 L11.62 412.16 L10.69 412.16 L10.69
+							 412.7 ZM11.81 412.7 L12.75 412.7 L12.75 412.16 L11.81 412.16 L11.81 412.7 ZM12.94 412.7 L13.87 412.7
+							 L13.87 412.16 L12.94 412.16 L12.94 412.7 ZM14.06 412.7 L15 412.7 L15 412.16 L14.06 412.16 L14.06 412.7
+							 ZM1.69 413.39 L2.63 413.39 L2.63 412.84 L1.69 412.84 L1.69 413.39 ZM2.81 413.39 L3.75 413.39 L3.75 412.84
+							 L2.81 412.84 L2.81 413.39 ZM3.94 413.39 L4.87 413.39 L4.87 412.84 L3.94 412.84 L3.94 413.39 ZM5.06 413.39
+							 L6 413.39 L6 412.84 L5.06 412.84 L5.06 413.39 ZM6.19 413.39 L7.12 413.39 L7.12 412.84 L6.19 412.84 L6.19
+							 413.39 ZM7.31 413.39 L8.25 413.39 L8.25 412.84 L7.31 412.84 L7.31 413.39 ZM8.44 413.39 L9.37 413.39
+							 L9.37 412.84 L8.44 412.84 L8.44 413.39 ZM9.56 413.39 L10.5 413.39 L10.5 412.84 L9.56 412.84 L9.56 413.39
+							 ZM10.69 413.39 L11.62 413.39 L11.62 412.84 L10.69 412.84 L10.69 413.39 ZM11.81 413.39 L12.75 413.39
+							 L12.75 412.84 L11.81 412.84 L11.81 413.39 ZM12.94 413.39 L13.87 413.39 L13.87 412.84 L12.94 412.84 L12.94
+							 413.39 ZM14.06 413.39 L15 413.39 L15 412.84 L14.06 412.84 L14.06 413.39 ZM1.69 414.07 L2.63 414.07 L2.63
+							 413.52 L1.69 413.52 L1.69 414.07 ZM2.81 414.07 L3.75 414.07 L3.75 413.52 L2.81 413.52 L2.81 414.07 ZM3.94
+							 414.07 L4.87 414.07 L4.87 413.52 L3.94 413.52 L3.94 414.07 ZM5.06 414.07 L6 414.07 L6 413.52 L5.06 413.52
+							 L5.06 414.07 ZM6.19 414.07 L7.12 414.07 L7.12 413.52 L6.19 413.52 L6.19 414.07 ZM7.31 414.07 L8.25 414.07
+							 L8.25 413.52 L7.31 413.52 L7.31 414.07 ZM8.44 414.07 L9.37 414.07 L9.37 413.52 L8.44 413.52 L8.44 414.07
+							 ZM9.56 414.07 L10.5 414.07 L10.5 413.52 L9.56 413.52 L9.56 414.07 ZM10.69 414.07 L11.62 414.07 L11.62
+							 413.52 L10.69 413.52 L10.69 414.07 ZM11.81 414.07 L12.75 414.07 L12.75 413.52 L11.81 413.52 L11.81 414.07
+							 ZM12.94 414.07 L13.87 414.07 L13.87 413.52 L12.94 413.52 L12.94 414.07 ZM3.94 414.75 L11.62 414.75 L11.62
+							 414.2 L3.94 414.2 L3.94 414.75 ZM21 414.75 L23.25 414.75 L23.25 414.2 L21 414.2 L21 414.75 ZM23.44 414.75
+							 L24.37 414.75 L24.37 414.2 L23.44 414.2 L23.44 414.75 ZM23.44 414.07 L24.37 414.07 L24.37 413.52 L23.44
+							 413.52 L23.44 414.07 ZM22.22 414.07 L23.16 414.07 L23.16 413.52 L22.22 413.52 L22.22 414.07 ZM21 414.07
+							 L21.94 414.07 L21.94 413.52 L21 413.52 L21 414.07 ZM21 413.39 L21.94 413.39 L21.94 412.84 L21 412.84
+							 L21 413.39 ZM21 412.7 L21.94 412.7 L21.94 412.16 L21 412.16 L21 412.7 ZM22.22 412.7 L23.16 412.7 L23.16
+							 412.16 L22.22 412.16 L22.22 412.7 ZM23.44 412.7 L24.37 412.7 L24.37 412.16 L23.44 412.16 L23.44 412.7
+							 ZM23.44 413.39 L24.37 413.39 L24.37 412.84 L23.44 412.84 L23.44 413.39 ZM22.22 413.39 L23.16 413.39
+							 L23.16 412.84 L22.22 412.84 L22.22 413.39 Z" class="st10"/>
+			</g>
+			<g id="shape45-118" transform="translate(-391.623,414.188) rotate(-90)">
+				<title>Sheet.45</title>
+				<path d="M0 410.93 L0.94 410.93 L0.94 410.39 L0 410.39 L0 410.93 ZM0 412.7 L1.5 412.7 L1.5 412.16 L0 412.16 L0 412.7
+							 ZM0 413.39 L1.5 413.39 L1.5 412.84 L0 412.84 L0 413.39 ZM0 414.07 L1.5 414.07 L1.5 413.52 L0 413.52
+							 L0 414.07 ZM0 414.75 L1.5 414.75 L1.5 414.2 L0 414.2 L0 414.75 ZM1.69 414.75 L2.63 414.75 L2.63 414.2
+							 L1.69 414.2 L1.69 414.75 ZM2.81 414.75 L3.75 414.75 L3.75 414.2 L2.81 414.2 L2.81 414.75 ZM11.81 414.75
+							 L12.75 414.75 L12.75 414.2 L11.81 414.2 L11.81 414.75 ZM12.94 414.75 L13.87 414.75 L13.87 414.2 L12.94
+							 414.2 L12.94 414.75 ZM14.06 414.75 L15 414.75 L15 414.2 L14.06 414.2 L14.06 414.75 ZM15.19 414.75 L16.69
+							 414.75 L16.69 414.2 L15.19 414.2 L15.19 414.75 ZM17.25 414.75 L18.19 414.75 L18.19 414.2 L17.25 414.2
+							 L17.25 414.75 ZM18.37 414.75 L19.31 414.75 L19.31 414.2 L18.37 414.2 L18.37 414.75 ZM19.5 414.75 L20.44
+							 414.75 L20.44 414.2 L19.5 414.2 L19.5 414.75 ZM24.66 414.75 L25.59 414.75 L25.59 413.55 L24.66 413.55
+							 L24.66 414.75 ZM24.66 413.44 L25.59 413.44 L25.59 412.16 L24.66 412.16 L24.66 413.44 ZM24.66 412.02
+							 L25.59 412.02 L25.59 411.48 L24.66 411.48 L24.66 412.02 ZM23.44 412.02 L24.37 412.02 L24.37 411.48 L23.44
+							 411.48 L23.44 412.02 ZM22.22 412.02 L23.16 412.02 L23.16 411.48 L22.22 411.48 L22.22 412.02 ZM21 412.02
+							 L21.94 412.02 L21.94 411.48 L21 411.48 L21 412.02 ZM19.5 412.02 L20.44 412.02 L20.44 411.48 L19.5 411.48
+							 L19.5 412.02 ZM19.5 412.7 L20.44 412.7 L20.44 412.16 L19.5 412.16 L19.5 412.7 ZM18.37 414.07 L19.31
+							 414.07 L19.31 413.52 L18.37 413.52 L18.37 414.07 ZM14.06 414.06 L16.69 414.06 L16.69 413.51 L14.06 413.51
+							 L14.06 414.06 ZM15.19 413.37 L16.69 413.37 L16.69 412.17 L15.19 412.17 L15.19 413.37 ZM17.25 412.7 L18.19
+							 412.7 L18.19 412.16 L17.25 412.16 L17.25 412.7 ZM18.37 412.7 L19.31 412.7 L19.31 412.16 L18.37 412.16
+							 L18.37 412.7 ZM18.37 412.02 L19.31 412.02 L19.31 411.48 L18.37 411.48 L18.37 412.02 ZM15.19 412.02 L16.69
+							 412.02 L16.69 411.48 L15.19 411.48 L15.19 412.02 ZM24.19 410.6 L24.94 410.6 L24.94 410.5 L24.19 410.5
+							 L24.19 410.6 ZM23.06 410.6 L23.81 410.6 L23.81 410.5 L23.06 410.5 L23.06 410.6 ZM19.5 410.93 L20.44
+							 410.93 L20.44 410.39 L19.5 410.39 L19.5 410.93 ZM18.37 410.93 L19.31 410.93 L19.31 410.39 L18.37 410.39
+							 L18.37 410.93 ZM17.25 410.93 L18.19 410.93 L18.19 410.39 L17.25 410.39 L17.25 410.93 ZM10.31 410.93
+							 L11.25 410.93 L11.25 410.39 L10.31 410.39 L10.31 410.93 ZM9.19 410.93 L10.12 410.93 L10.12 410.39 L9.19
+							 410.39 L9.19 410.93 ZM8.06 410.93 L9 410.93 L9 410.39 L8.06 410.39 L8.06 410.93 ZM6.94 410.93 L7.87
+							 410.93 L7.87 410.39 L6.94 410.39 L6.94 410.93 ZM17.25 412.02 L18.19 412.02 L18.19 411.48 L17.25 411.48
+							 L17.25 412.02 Z" class="st11"/>
+			</g>
+		</g>
+		<g id="shape46-120" transform="translate(360.375,-72.375)">
+			<title>Sheet.46</title>
+			<path d="M0 414.75 L26.19 414.75" class="st4"/>
+		</g>
+		<g id="group48-125" transform="translate(396.436,-22.875)">
+			<title>Terminal.48</title>
+			<g id="shape49-126" transform="translate(-391.186,414.75) rotate(-90)">
+				<title>Sheet.49</title>
+				<path d="M0 414.75 L27 414.75 L27 409.08 L0 409.08 L0 414.75 ZM26.25 403.93 L23.44 399.37 L3.53 399.37 L0.75 403.93
+							 L26.25 403.93 ZM23.44 399.37 L23.44 391.19 L3.53 391.19 L3.53 399.37 L23.44 399.37 ZM26.25 407.7 L26.25
+							 403.93 L0.75 403.93 L0.75 407.7 L26.25 407.7 ZM24.83 407.7 A1223.48 394.162 90 0 1 2.17 407.7 L24.83
+							 407.7 Z" class="st8"/>
+			</g>
+			<g id="shape50-128" transform="translate(-395.768,392.25) rotate(-90)">
+				<title>Sheet.50</title>
+				<rect x="0" y="414.641" width="0.75" height="0.109091" class="st9"/>
+			</g>
+			<g id="shape51-130" transform="translate(-391.623,414.188) rotate(-90)">
+				<title>Sheet.51</title>
+				<path d="M1.69 410.93 L2.63 410.93 L2.63 410.39 L1.69 410.39 L1.69 410.93 ZM2.81 410.93 L3.75 410.93 L3.75 410.39
+							 L2.81 410.39 L2.81 410.93 ZM3.94 410.93 L4.87 410.93 L4.87 410.39 L3.94 410.39 L3.94 410.93 ZM5.06 410.93
+							 L6 410.93 L6 410.39 L5.06 410.39 L5.06 410.93 ZM12.28 410.93 L13.22 410.93 L13.22 410.39 L12.28 410.39
+							 L12.28 410.93 ZM13.41 410.93 L14.34 410.93 L14.34 410.39 L13.41 410.39 L13.41 410.93 ZM14.53 410.93
+							 L15.47 410.93 L15.47 410.39 L14.53 410.39 L14.53 410.93 ZM15.66 410.93 L16.59 410.93 L16.59 410.39 L15.66
+							 410.39 L15.66 410.93 ZM0 412.02 L1.5 412.02 L1.5 411.48 L0 411.48 L0 412.02 ZM1.69 412.02 L2.63 412.02
+							 L2.63 411.48 L1.69 411.48 L1.69 412.02 ZM2.81 412.02 L3.75 412.02 L3.75 411.48 L2.81 411.48 L2.81 412.02
+							 ZM3.94 412.02 L4.87 412.02 L4.87 411.48 L3.94 411.48 L3.94 412.02 ZM5.06 412.02 L6 412.02 L6 411.48
+							 L5.06 411.48 L5.06 412.02 ZM6.19 412.02 L7.12 412.02 L7.12 411.48 L6.19 411.48 L6.19 412.02 ZM7.31 412.02
+							 L8.25 412.02 L8.25 411.48 L7.31 411.48 L7.31 412.02 ZM8.44 412.02 L9.37 412.02 L9.37 411.48 L8.44 411.48
+							 L8.44 412.02 ZM9.56 412.02 L10.5 412.02 L10.5 411.48 L9.56 411.48 L9.56 412.02 ZM10.69 412.02 L11.62
+							 412.02 L11.62 411.48 L10.69 411.48 L10.69 412.02 ZM11.81 412.02 L12.75 412.02 L12.75 411.48 L11.81 411.48
+							 L11.81 412.02 ZM12.94 412.02 L13.87 412.02 L13.87 411.48 L12.94 411.48 L12.94 412.02 ZM14.06 412.02
+							 L15 412.02 L15 411.48 L14.06 411.48 L14.06 412.02 ZM1.69 412.7 L2.63 412.7 L2.63 412.16 L1.69 412.16
+							 L1.69 412.7 ZM2.81 412.7 L3.75 412.7 L3.75 412.16 L2.81 412.16 L2.81 412.7 ZM3.94 412.7 L4.87 412.7
+							 L4.87 412.16 L3.94 412.16 L3.94 412.7 ZM5.06 412.7 L6 412.7 L6 412.16 L5.06 412.16 L5.06 412.7 ZM6.19
+							 412.7 L7.12 412.7 L7.12 412.16 L6.19 412.16 L6.19 412.7 ZM7.31 412.7 L8.25 412.7 L8.25 412.16 L7.31
+							 412.16 L7.31 412.7 ZM8.44 412.7 L9.37 412.7 L9.37 412.16 L8.44 412.16 L8.44 412.7 ZM9.56 412.7 L10.5
+							 412.7 L10.5 412.16 L9.56 412.16 L9.56 412.7 ZM10.69 412.7 L11.62 412.7 L11.62 412.16 L10.69 412.16 L10.69
+							 412.7 ZM11.81 412.7 L12.75 412.7 L12.75 412.16 L11.81 412.16 L11.81 412.7 ZM12.94 412.7 L13.87 412.7
+							 L13.87 412.16 L12.94 412.16 L12.94 412.7 ZM14.06 412.7 L15 412.7 L15 412.16 L14.06 412.16 L14.06 412.7
+							 ZM1.69 413.39 L2.63 413.39 L2.63 412.84 L1.69 412.84 L1.69 413.39 ZM2.81 413.39 L3.75 413.39 L3.75 412.84
+							 L2.81 412.84 L2.81 413.39 ZM3.94 413.39 L4.87 413.39 L4.87 412.84 L3.94 412.84 L3.94 413.39 ZM5.06 413.39
+							 L6 413.39 L6 412.84 L5.06 412.84 L5.06 413.39 ZM6.19 413.39 L7.12 413.39 L7.12 412.84 L6.19 412.84 L6.19
+							 413.39 ZM7.31 413.39 L8.25 413.39 L8.25 412.84 L7.31 412.84 L7.31 413.39 ZM8.44 413.39 L9.37 413.39
+							 L9.37 412.84 L8.44 412.84 L8.44 413.39 ZM9.56 413.39 L10.5 413.39 L10.5 412.84 L9.56 412.84 L9.56 413.39
+							 ZM10.69 413.39 L11.62 413.39 L11.62 412.84 L10.69 412.84 L10.69 413.39 ZM11.81 413.39 L12.75 413.39
+							 L12.75 412.84 L11.81 412.84 L11.81 413.39 ZM12.94 413.39 L13.87 413.39 L13.87 412.84 L12.94 412.84 L12.94
+							 413.39 ZM14.06 413.39 L15 413.39 L15 412.84 L14.06 412.84 L14.06 413.39 ZM1.69 414.07 L2.63 414.07 L2.63
+							 413.52 L1.69 413.52 L1.69 414.07 ZM2.81 414.07 L3.75 414.07 L3.75 413.52 L2.81 413.52 L2.81 414.07 ZM3.94
+							 414.07 L4.87 414.07 L4.87 413.52 L3.94 413.52 L3.94 414.07 ZM5.06 414.07 L6 414.07 L6 413.52 L5.06 413.52
+							 L5.06 414.07 ZM6.19 414.07 L7.12 414.07 L7.12 413.52 L6.19 413.52 L6.19 414.07 ZM7.31 414.07 L8.25 414.07
+							 L8.25 413.52 L7.31 413.52 L7.31 414.07 ZM8.44 414.07 L9.37 414.07 L9.37 413.52 L8.44 413.52 L8.44 414.07
+							 ZM9.56 414.07 L10.5 414.07 L10.5 413.52 L9.56 413.52 L9.56 414.07 ZM10.69 414.07 L11.62 414.07 L11.62
+							 413.52 L10.69 413.52 L10.69 414.07 ZM11.81 414.07 L12.75 414.07 L12.75 413.52 L11.81 413.52 L11.81 414.07
+							 ZM12.94 414.07 L13.87 414.07 L13.87 413.52 L12.94 413.52 L12.94 414.07 ZM3.94 414.75 L11.62 414.75 L11.62
+							 414.2 L3.94 414.2 L3.94 414.75 ZM21 414.75 L23.25 414.75 L23.25 414.2 L21 414.2 L21 414.75 ZM23.44 414.75
+							 L24.37 414.75 L24.37 414.2 L23.44 414.2 L23.44 414.75 ZM23.44 414.07 L24.37 414.07 L24.37 413.52 L23.44
+							 413.52 L23.44 414.07 ZM22.22 414.07 L23.16 414.07 L23.16 413.52 L22.22 413.52 L22.22 414.07 ZM21 414.07
+							 L21.94 414.07 L21.94 413.52 L21 413.52 L21 414.07 ZM21 413.39 L21.94 413.39 L21.94 412.84 L21 412.84
+							 L21 413.39 ZM21 412.7 L21.94 412.7 L21.94 412.16 L21 412.16 L21 412.7 ZM22.22 412.7 L23.16 412.7 L23.16
+							 412.16 L22.22 412.16 L22.22 412.7 ZM23.44 412.7 L24.37 412.7 L24.37 412.16 L23.44 412.16 L23.44 412.7
+							 ZM23.44 413.39 L24.37 413.39 L24.37 412.84 L23.44 412.84 L23.44 413.39 ZM22.22 413.39 L23.16 413.39
+							 L23.16 412.84 L22.22 412.84 L22.22 413.39 Z" class="st10"/>
+			</g>
+			<g id="shape52-132" transform="translate(-391.623,414.188) rotate(-90)">
+				<title>Sheet.52</title>
+				<path d="M0 410.93 L0.94 410.93 L0.94 410.39 L0 410.39 L0 410.93 ZM0 412.7 L1.5 412.7 L1.5 412.16 L0 412.16 L0 412.7
+							 ZM0 413.39 L1.5 413.39 L1.5 412.84 L0 412.84 L0 413.39 ZM0 414.07 L1.5 414.07 L1.5 413.52 L0 413.52
+							 L0 414.07 ZM0 414.75 L1.5 414.75 L1.5 414.2 L0 414.2 L0 414.75 ZM1.69 414.75 L2.63 414.75 L2.63 414.2
+							 L1.69 414.2 L1.69 414.75 ZM2.81 414.75 L3.75 414.75 L3.75 414.2 L2.81 414.2 L2.81 414.75 ZM11.81 414.75
+							 L12.75 414.75 L12.75 414.2 L11.81 414.2 L11.81 414.75 ZM12.94 414.75 L13.87 414.75 L13.87 414.2 L12.94
+							 414.2 L12.94 414.75 ZM14.06 414.75 L15 414.75 L15 414.2 L14.06 414.2 L14.06 414.75 ZM15.19 414.75 L16.69
+							 414.75 L16.69 414.2 L15.19 414.2 L15.19 414.75 ZM17.25 414.75 L18.19 414.75 L18.19 414.2 L17.25 414.2
+							 L17.25 414.75 ZM18.37 414.75 L19.31 414.75 L19.31 414.2 L18.37 414.2 L18.37 414.75 ZM19.5 414.75 L20.44
+							 414.75 L20.44 414.2 L19.5 414.2 L19.5 414.75 ZM24.66 414.75 L25.59 414.75 L25.59 413.55 L24.66 413.55
+							 L24.66 414.75 ZM24.66 413.44 L25.59 413.44 L25.59 412.16 L24.66 412.16 L24.66 413.44 ZM24.66 412.02
+							 L25.59 412.02 L25.59 411.48 L24.66 411.48 L24.66 412.02 ZM23.44 412.02 L24.37 412.02 L24.37 411.48 L23.44
+							 411.48 L23.44 412.02 ZM22.22 412.02 L23.16 412.02 L23.16 411.48 L22.22 411.48 L22.22 412.02 ZM21 412.02
+							 L21.94 412.02 L21.94 411.48 L21 411.48 L21 412.02 ZM19.5 412.02 L20.44 412.02 L20.44 411.48 L19.5 411.48
+							 L19.5 412.02 ZM19.5 412.7 L20.44 412.7 L20.44 412.16 L19.5 412.16 L19.5 412.7 ZM18.37 414.07 L19.31
+							 414.07 L19.31 413.52 L18.37 413.52 L18.37 414.07 ZM14.06 414.06 L16.69 414.06 L16.69 413.51 L14.06 413.51
+							 L14.06 414.06 ZM15.19 413.37 L16.69 413.37 L16.69 412.17 L15.19 412.17 L15.19 413.37 ZM17.25 412.7 L18.19
+							 412.7 L18.19 412.16 L17.25 412.16 L17.25 412.7 ZM18.37 412.7 L19.31 412.7 L19.31 412.16 L18.37 412.16
+							 L18.37 412.7 ZM18.37 412.02 L19.31 412.02 L19.31 411.48 L18.37 411.48 L18.37 412.02 ZM15.19 412.02 L16.69
+							 412.02 L16.69 411.48 L15.19 411.48 L15.19 412.02 ZM24.19 410.6 L24.94 410.6 L24.94 410.5 L24.19 410.5
+							 L24.19 410.6 ZM23.06 410.6 L23.81 410.6 L23.81 410.5 L23.06 410.5 L23.06 410.6 ZM19.5 410.93 L20.44
+							 410.93 L20.44 410.39 L19.5 410.39 L19.5 410.93 ZM18.37 410.93 L19.31 410.93 L19.31 410.39 L18.37 410.39
+							 L18.37 410.93 ZM17.25 410.93 L18.19 410.93 L18.19 410.39 L17.25 410.39 L17.25 410.93 ZM10.31 410.93
+							 L11.25 410.93 L11.25 410.39 L10.31 410.39 L10.31 410.93 ZM9.19 410.93 L10.12 410.93 L10.12 410.39 L9.19
+							 410.39 L9.19 410.93 ZM8.06 410.93 L9 410.93 L9 410.39 L8.06 410.39 L8.06 410.93 ZM6.94 410.93 L7.87
+							 410.93 L7.87 410.39 L6.94 410.39 L6.94 410.93 ZM17.25 412.02 L18.19 412.02 L18.19 411.48 L17.25 411.48
+							 L17.25 412.02 Z" class="st11"/>
+			</g>
+		</g>
+		<g id="shape53-134" transform="translate(360.293,-36.375)">
+			<title>Sheet.53</title>
+			<path d="M0 414.75 L26.27 414.75" class="st4"/>
+		</g>
+		<g id="group22-139" transform="translate(396.375,-310.875)">
+			<title>Terminal.22</title>
+			<g id="shape23-140" transform="translate(-391.186,414.75) rotate(-90)">
+				<title>Sheet.23</title>
+				<path d="M0 414.75 L27 414.75 L27 409.08 L0 409.08 L0 414.75 ZM26.25 403.93 L23.44 399.37 L3.53 399.37 L0.75 403.93
+							 L26.25 403.93 ZM23.44 399.37 L23.44 391.19 L3.53 391.19 L3.53 399.37 L23.44 399.37 ZM26.25 407.7 L26.25
+							 403.93 L0.75 403.93 L0.75 407.7 L26.25 407.7 ZM24.83 407.7 A1223.48 394.162 90 0 1 2.17 407.7 L24.83
+							 407.7 Z" class="st8"/>
+			</g>
+			<g id="shape24-142" transform="translate(-395.768,392.25) rotate(-90)">
+				<title>Sheet.24</title>
+				<rect x="0" y="414.641" width="0.75" height="0.109091" class="st9"/>
+			</g>
+			<g id="shape25-144" transform="translate(-391.623,414.188) rotate(-90)">
+				<title>Sheet.25</title>
+				<path d="M1.69 410.93 L2.63 410.93 L2.63 410.39 L1.69 410.39 L1.69 410.93 ZM2.81 410.93 L3.75 410.93 L3.75 410.39
+							 L2.81 410.39 L2.81 410.93 ZM3.94 410.93 L4.87 410.93 L4.87 410.39 L3.94 410.39 L3.94 410.93 ZM5.06 410.93
+							 L6 410.93 L6 410.39 L5.06 410.39 L5.06 410.93 ZM12.28 410.93 L13.22 410.93 L13.22 410.39 L12.28 410.39
+							 L12.28 410.93 ZM13.41 410.93 L14.34 410.93 L14.34 410.39 L13.41 410.39 L13.41 410.93 ZM14.53 410.93
+							 L15.47 410.93 L15.47 410.39 L14.53 410.39 L14.53 410.93 ZM15.66 410.93 L16.59 410.93 L16.59 410.39 L15.66
+							 410.39 L15.66 410.93 ZM0 412.02 L1.5 412.02 L1.5 411.48 L0 411.48 L0 412.02 ZM1.69 412.02 L2.63 412.02
+							 L2.63 411.48 L1.69 411.48 L1.69 412.02 ZM2.81 412.02 L3.75 412.02 L3.75 411.48 L2.81 411.48 L2.81 412.02
+							 ZM3.94 412.02 L4.87 412.02 L4.87 411.48 L3.94 411.48 L3.94 412.02 ZM5.06 412.02 L6 412.02 L6 411.48
+							 L5.06 411.48 L5.06 412.02 ZM6.19 412.02 L7.12 412.02 L7.12 411.48 L6.19 411.48 L6.19 412.02 ZM7.31 412.02
+							 L8.25 412.02 L8.25 411.48 L7.31 411.48 L7.31 412.02 ZM8.44 412.02 L9.37 412.02 L9.37 411.48 L8.44 411.48
+							 L8.44 412.02 ZM9.56 412.02 L10.5 412.02 L10.5 411.48 L9.56 411.48 L9.56 412.02 ZM10.69 412.02 L11.62
+							 412.02 L11.62 411.48 L10.69 411.48 L10.69 412.02 ZM11.81 412.02 L12.75 412.02 L12.75 411.48 L11.81 411.48
+							 L11.81 412.02 ZM12.94 412.02 L13.87 412.02 L13.87 411.48 L12.94 411.48 L12.94 412.02 ZM14.06 412.02
+							 L15 412.02 L15 411.48 L14.06 411.48 L14.06 412.02 ZM1.69 412.7 L2.63 412.7 L2.63 412.16 L1.69 412.16
+							 L1.69 412.7 ZM2.81 412.7 L3.75 412.7 L3.75 412.16 L2.81 412.16 L2.81 412.7 ZM3.94 412.7 L4.87 412.7
+							 L4.87 412.16 L3.94 412.16 L3.94 412.7 ZM5.06 412.7 L6 412.7 L6 412.16 L5.06 412.16 L5.06 412.7 ZM6.19
+							 412.7 L7.12 412.7 L7.12 412.16 L6.19 412.16 L6.19 412.7 ZM7.31 412.7 L8.25 412.7 L8.25 412.16 L7.31
+							 412.16 L7.31 412.7 ZM8.44 412.7 L9.37 412.7 L9.37 412.16 L8.44 412.16 L8.44 412.7 ZM9.56 412.7 L10.5
+							 412.7 L10.5 412.16 L9.56 412.16 L9.56 412.7 ZM10.69 412.7 L11.62 412.7 L11.62 412.16 L10.69 412.16 L10.69
+							 412.7 ZM11.81 412.7 L12.75 412.7 L12.75 412.16 L11.81 412.16 L11.81 412.7 ZM12.94 412.7 L13.87 412.7
+							 L13.87 412.16 L12.94 412.16 L12.94 412.7 ZM14.06 412.7 L15 412.7 L15 412.16 L14.06 412.16 L14.06 412.7
+							 ZM1.69 413.39 L2.63 413.39 L2.63 412.84 L1.69 412.84 L1.69 413.39 ZM2.81 413.39 L3.75 413.39 L3.75 412.84
+							 L2.81 412.84 L2.81 413.39 ZM3.94 413.39 L4.87 413.39 L4.87 412.84 L3.94 412.84 L3.94 413.39 ZM5.06 413.39
+							 L6 413.39 L6 412.84 L5.06 412.84 L5.06 413.39 ZM6.19 413.39 L7.12 413.39 L7.12 412.84 L6.19 412.84 L6.19
+							 413.39 ZM7.31 413.39 L8.25 413.39 L8.25 412.84 L7.31 412.84 L7.31 413.39 ZM8.44 413.39 L9.37 413.39
+							 L9.37 412.84 L8.44 412.84 L8.44 413.39 ZM9.56 413.39 L10.5 413.39 L10.5 412.84 L9.56 412.84 L9.56 413.39
+							 ZM10.69 413.39 L11.62 413.39 L11.62 412.84 L10.69 412.84 L10.69 413.39 ZM11.81 413.39 L12.75 413.39
+							 L12.75 412.84 L11.81 412.84 L11.81 413.39 ZM12.94 413.39 L13.87 413.39 L13.87 412.84 L12.94 412.84 L12.94
+							 413.39 ZM14.06 413.39 L15 413.39 L15 412.84 L14.06 412.84 L14.06 413.39 ZM1.69 414.07 L2.63 414.07 L2.63
+							 413.52 L1.69 413.52 L1.69 414.07 ZM2.81 414.07 L3.75 414.07 L3.75 413.52 L2.81 413.52 L2.81 414.07 ZM3.94
+							 414.07 L4.87 414.07 L4.87 413.52 L3.94 413.52 L3.94 414.07 ZM5.06 414.07 L6 414.07 L6 413.52 L5.06 413.52
+							 L5.06 414.07 ZM6.19 414.07 L7.12 414.07 L7.12 413.52 L6.19 413.52 L6.19 414.07 ZM7.31 414.07 L8.25 414.07
+							 L8.25 413.52 L7.31 413.52 L7.31 414.07 ZM8.44 414.07 L9.37 414.07 L9.37 413.52 L8.44 413.52 L8.44 414.07
+							 ZM9.56 414.07 L10.5 414.07 L10.5 413.52 L9.56 413.52 L9.56 414.07 ZM10.69 414.07 L11.62 414.07 L11.62
+							 413.52 L10.69 413.52 L10.69 414.07 ZM11.81 414.07 L12.75 414.07 L12.75 413.52 L11.81 413.52 L11.81 414.07
+							 ZM12.94 414.07 L13.87 414.07 L13.87 413.52 L12.94 413.52 L12.94 414.07 ZM3.94 414.75 L11.62 414.75 L11.62
+							 414.2 L3.94 414.2 L3.94 414.75 ZM21 414.75 L23.25 414.75 L23.25 414.2 L21 414.2 L21 414.75 ZM23.44 414.75
+							 L24.37 414.75 L24.37 414.2 L23.44 414.2 L23.44 414.75 ZM23.44 414.07 L24.37 414.07 L24.37 413.52 L23.44
+							 413.52 L23.44 414.07 ZM22.22 414.07 L23.16 414.07 L23.16 413.52 L22.22 413.52 L22.22 414.07 ZM21 414.07
+							 L21.94 414.07 L21.94 413.52 L21 413.52 L21 414.07 ZM21 413.39 L21.94 413.39 L21.94 412.84 L21 412.84
+							 L21 413.39 ZM21 412.7 L21.94 412.7 L21.94 412.16 L21 412.16 L21 412.7 ZM22.22 412.7 L23.16 412.7 L23.16
+							 412.16 L22.22 412.16 L22.22 412.7 ZM23.44 412.7 L24.37 412.7 L24.37 412.16 L23.44 412.16 L23.44 412.7
+							 ZM23.44 413.39 L24.37 413.39 L24.37 412.84 L23.44 412.84 L23.44 413.39 ZM22.22 413.39 L23.16 413.39
+							 L23.16 412.84 L22.22 412.84 L22.22 413.39 Z" class="st10"/>
+			</g>
+			<g id="shape26-146" transform="translate(-391.623,414.188) rotate(-90)">
+				<title>Sheet.26</title>
+				<path d="M0 410.93 L0.94 410.93 L0.94 410.39 L0 410.39 L0 410.93 ZM0 412.7 L1.5 412.7 L1.5 412.16 L0 412.16 L0 412.7
+							 ZM0 413.39 L1.5 413.39 L1.5 412.84 L0 412.84 L0 413.39 ZM0 414.07 L1.5 414.07 L1.5 413.52 L0 413.52
+							 L0 414.07 ZM0 414.75 L1.5 414.75 L1.5 414.2 L0 414.2 L0 414.75 ZM1.69 414.75 L2.63 414.75 L2.63 414.2
+							 L1.69 414.2 L1.69 414.75 ZM2.81 414.75 L3.75 414.75 L3.75 414.2 L2.81 414.2 L2.81 414.75 ZM11.81 414.75
+							 L12.75 414.75 L12.75 414.2 L11.81 414.2 L11.81 414.75 ZM12.94 414.75 L13.87 414.75 L13.87 414.2 L12.94
+							 414.2 L12.94 414.75 ZM14.06 414.75 L15 414.75 L15 414.2 L14.06 414.2 L14.06 414.75 ZM15.19 414.75 L16.69
+							 414.75 L16.69 414.2 L15.19 414.2 L15.19 414.75 ZM17.25 414.75 L18.19 414.75 L18.19 414.2 L17.25 414.2
+							 L17.25 414.75 ZM18.37 414.75 L19.31 414.75 L19.31 414.2 L18.37 414.2 L18.37 414.75 ZM19.5 414.75 L20.44
+							 414.75 L20.44 414.2 L19.5 414.2 L19.5 414.75 ZM24.66 414.75 L25.59 414.75 L25.59 413.55 L24.66 413.55
+							 L24.66 414.75 ZM24.66 413.44 L25.59 413.44 L25.59 412.16 L24.66 412.16 L24.66 413.44 ZM24.66 412.02
+							 L25.59 412.02 L25.59 411.48 L24.66 411.48 L24.66 412.02 ZM23.44 412.02 L24.37 412.02 L24.37 411.48 L23.44
+							 411.48 L23.44 412.02 ZM22.22 412.02 L23.16 412.02 L23.16 411.48 L22.22 411.48 L22.22 412.02 ZM21 412.02
+							 L21.94 412.02 L21.94 411.48 L21 411.48 L21 412.02 ZM19.5 412.02 L20.44 412.02 L20.44 411.48 L19.5 411.48
+							 L19.5 412.02 ZM19.5 412.7 L20.44 412.7 L20.44 412.16 L19.5 412.16 L19.5 412.7 ZM18.37 414.07 L19.31
+							 414.07 L19.31 413.52 L18.37 413.52 L18.37 414.07 ZM14.06 414.06 L16.69 414.06 L16.69 413.51 L14.06 413.51
+							 L14.06 414.06 ZM15.19 413.37 L16.69 413.37 L16.69 412.17 L15.19 412.17 L15.19 413.37 ZM17.25 412.7 L18.19
+							 412.7 L18.19 412.16 L17.25 412.16 L17.25 412.7 ZM18.37 412.7 L19.31 412.7 L19.31 412.16 L18.37 412.16
+							 L18.37 412.7 ZM18.37 412.02 L19.31 412.02 L19.31 411.48 L18.37 411.48 L18.37 412.02 ZM15.19 412.02 L16.69
+							 412.02 L16.69 411.48 L15.19 411.48 L15.19 412.02 ZM24.19 410.6 L24.94 410.6 L24.94 410.5 L24.19 410.5
+							 L24.19 410.6 ZM23.06 410.6 L23.81 410.6 L23.81 410.5 L23.06 410.5 L23.06 410.6 ZM19.5 410.93 L20.44
+							 410.93 L20.44 410.39 L19.5 410.39 L19.5 410.93 ZM18.37 410.93 L19.31 410.93 L19.31 410.39 L18.37 410.39
+							 L18.37 410.93 ZM17.25 410.93 L18.19 410.93 L18.19 410.39 L17.25 410.39 L17.25 410.93 ZM10.31 410.93
+							 L11.25 410.93 L11.25 410.39 L10.31 410.39 L10.31 410.93 ZM9.19 410.93 L10.12 410.93 L10.12 410.39 L9.19
+							 410.39 L9.19 410.93 ZM8.06 410.93 L9 410.93 L9 410.39 L8.06 410.39 L8.06 410.93 ZM6.94 410.93 L7.87
+							 410.93 L7.87 410.39 L6.94 410.39 L6.94 410.93 ZM17.25 412.02 L18.19 412.02 L18.19 411.48 L17.25 411.48
+							 L17.25 412.02 Z" class="st11"/>
+			</g>
+		</g>
+		<g id="shape28-148" transform="translate(360.293,-324.375)">
+			<title>Sheet.28</title>
+			<path d="M0 414.75 L26.27 414.75" class="st4"/>
+		</g>
+		<g id="group29-153" transform="translate(396.375,-256.875)">
+			<title>Terminal.29</title>
+			<g id="shape30-154" transform="translate(-391.186,414.75) rotate(-90)">
+				<title>Sheet.30</title>
+				<path d="M0 414.75 L27 414.75 L27 409.08 L0 409.08 L0 414.75 ZM26.25 403.93 L23.44 399.37 L3.53 399.37 L0.75 403.93
+							 L26.25 403.93 ZM23.44 399.37 L23.44 391.19 L3.53 391.19 L3.53 399.37 L23.44 399.37 ZM26.25 407.7 L26.25
+							 403.93 L0.75 403.93 L0.75 407.7 L26.25 407.7 ZM24.83 407.7 A1223.48 394.162 90 0 1 2.17 407.7 L24.83
+							 407.7 Z" class="st8"/>
+			</g>
+			<g id="shape31-156" transform="translate(-395.768,392.25) rotate(-90)">
+				<title>Sheet.31</title>
+				<rect x="0" y="414.641" width="0.75" height="0.109091" class="st9"/>
+			</g>
+			<g id="shape32-158" transform="translate(-391.623,414.188) rotate(-90)">
+				<title>Sheet.32</title>
+				<path d="M1.69 410.93 L2.63 410.93 L2.63 410.39 L1.69 410.39 L1.69 410.93 ZM2.81 410.93 L3.75 410.93 L3.75 410.39
+							 L2.81 410.39 L2.81 410.93 ZM3.94 410.93 L4.87 410.93 L4.87 410.39 L3.94 410.39 L3.94 410.93 ZM5.06 410.93
+							 L6 410.93 L6 410.39 L5.06 410.39 L5.06 410.93 ZM12.28 410.93 L13.22 410.93 L13.22 410.39 L12.28 410.39
+							 L12.28 410.93 ZM13.41 410.93 L14.34 410.93 L14.34 410.39 L13.41 410.39 L13.41 410.93 ZM14.53 410.93
+							 L15.47 410.93 L15.47 410.39 L14.53 410.39 L14.53 410.93 ZM15.66 410.93 L16.59 410.93 L16.59 410.39 L15.66
+							 410.39 L15.66 410.93 ZM0 412.02 L1.5 412.02 L1.5 411.48 L0 411.48 L0 412.02 ZM1.69 412.02 L2.63 412.02
+							 L2.63 411.48 L1.69 411.48 L1.69 412.02 ZM2.81 412.02 L3.75 412.02 L3.75 411.48 L2.81 411.48 L2.81 412.02
+							 ZM3.94 412.02 L4.87 412.02 L4.87 411.48 L3.94 411.48 L3.94 412.02 ZM5.06 412.02 L6 412.02 L6 411.48
+							 L5.06 411.48 L5.06 412.02 ZM6.19 412.02 L7.12 412.02 L7.12 411.48 L6.19 411.48 L6.19 412.02 ZM7.31 412.02
+							 L8.25 412.02 L8.25 411.48 L7.31 411.48 L7.31 412.02 ZM8.44 412.02 L9.37 412.02 L9.37 411.48 L8.44 411.48
+							 L8.44 412.02 ZM9.56 412.02 L10.5 412.02 L10.5 411.48 L9.56 411.48 L9.56 412.02 ZM10.69 412.02 L11.62
+							 412.02 L11.62 411.48 L10.69 411.48 L10.69 412.02 ZM11.81 412.02 L12.75 412.02 L12.75 411.48 L11.81 411.48
+							 L11.81 412.02 ZM12.94 412.02 L13.87 412.02 L13.87 411.48 L12.94 411.48 L12.94 412.02 ZM14.06 412.02
+							 L15 412.02 L15 411.48 L14.06 411.48 L14.06 412.02 ZM1.69 412.7 L2.63 412.7 L2.63 412.16 L1.69 412.16
+							 L1.69 412.7 ZM2.81 412.7 L3.75 412.7 L3.75 412.16 L2.81 412.16 L2.81 412.7 ZM3.94 412.7 L4.87 412.7
+							 L4.87 412.16 L3.94 412.16 L3.94 412.7 ZM5.06 412.7 L6 412.7 L6 412.16 L5.06 412.16 L5.06 412.7 ZM6.19
+							 412.7 L7.12 412.7 L7.12 412.16 L6.19 412.16 L6.19 412.7 ZM7.31 412.7 L8.25 412.7 L8.25 412.16 L7.31
+							 412.16 L7.31 412.7 ZM8.44 412.7 L9.37 412.7 L9.37 412.16 L8.44 412.16 L8.44 412.7 ZM9.56 412.7 L10.5
+							 412.7 L10.5 412.16 L9.56 412.16 L9.56 412.7 ZM10.69 412.7 L11.62 412.7 L11.62 412.16 L10.69 412.16 L10.69
+							 412.7 ZM11.81 412.7 L12.75 412.7 L12.75 412.16 L11.81 412.16 L11.81 412.7 ZM12.94 412.7 L13.87 412.7
+							 L13.87 412.16 L12.94 412.16 L12.94 412.7 ZM14.06 412.7 L15 412.7 L15 412.16 L14.06 412.16 L14.06 412.7
+							 ZM1.69 413.39 L2.63 413.39 L2.63 412.84 L1.69 412.84 L1.69 413.39 ZM2.81 413.39 L3.75 413.39 L3.75 412.84
+							 L2.81 412.84 L2.81 413.39 ZM3.94 413.39 L4.87 413.39 L4.87 412.84 L3.94 412.84 L3.94 413.39 ZM5.06 413.39
+							 L6 413.39 L6 412.84 L5.06 412.84 L5.06 413.39 ZM6.19 413.39 L7.12 413.39 L7.12 412.84 L6.19 412.84 L6.19
+							 413.39 ZM7.31 413.39 L8.25 413.39 L8.25 412.84 L7.31 412.84 L7.31 413.39 ZM8.44 413.39 L9.37 413.39
+							 L9.37 412.84 L8.44 412.84 L8.44 413.39 ZM9.56 413.39 L10.5 413.39 L10.5 412.84 L9.56 412.84 L9.56 413.39
+							 ZM10.69 413.39 L11.62 413.39 L11.62 412.84 L10.69 412.84 L10.69 413.39 ZM11.81 413.39 L12.75 413.39
+							 L12.75 412.84 L11.81 412.84 L11.81 413.39 ZM12.94 413.39 L13.87 413.39 L13.87 412.84 L12.94 412.84 L12.94
+							 413.39 ZM14.06 413.39 L15 413.39 L15 412.84 L14.06 412.84 L14.06 413.39 ZM1.69 414.07 L2.63 414.07 L2.63
+							 413.52 L1.69 413.52 L1.69 414.07 ZM2.81 414.07 L3.75 414.07 L3.75 413.52 L2.81 413.52 L2.81 414.07 ZM3.94
+							 414.07 L4.87 414.07 L4.87 413.52 L3.94 413.52 L3.94 414.07 ZM5.06 414.07 L6 414.07 L6 413.52 L5.06 413.52
+							 L5.06 414.07 ZM6.19 414.07 L7.12 414.07 L7.12 413.52 L6.19 413.52 L6.19 414.07 ZM7.31 414.07 L8.25 414.07
+							 L8.25 413.52 L7.31 413.52 L7.31 414.07 ZM8.44 414.07 L9.37 414.07 L9.37 413.52 L8.44 413.52 L8.44 414.07
+							 ZM9.56 414.07 L10.5 414.07 L10.5 413.52 L9.56 413.52 L9.56 414.07 ZM10.69 414.07 L11.62 414.07 L11.62
+							 413.52 L10.69 413.52 L10.69 414.07 ZM11.81 414.07 L12.75 414.07 L12.75 413.52 L11.81 413.52 L11.81 414.07
+							 ZM12.94 414.07 L13.87 414.07 L13.87 413.52 L12.94 413.52 L12.94 414.07 ZM3.94 414.75 L11.62 414.75 L11.62
+							 414.2 L3.94 414.2 L3.94 414.75 ZM21 414.75 L23.25 414.75 L23.25 414.2 L21 414.2 L21 414.75 ZM23.44 414.75
+							 L24.37 414.75 L24.37 414.2 L23.44 414.2 L23.44 414.75 ZM23.44 414.07 L24.37 414.07 L24.37 413.52 L23.44
+							 413.52 L23.44 414.07 ZM22.22 414.07 L23.16 414.07 L23.16 413.52 L22.22 413.52 L22.22 414.07 ZM21 414.07
+							 L21.94 414.07 L21.94 413.52 L21 413.52 L21 414.07 ZM21 413.39 L21.94 413.39 L21.94 412.84 L21 412.84
+							 L21 413.39 ZM21 412.7 L21.94 412.7 L21.94 412.16 L21 412.16 L21 412.7 ZM22.22 412.7 L23.16 412.7 L23.16
+							 412.16 L22.22 412.16 L22.22 412.7 ZM23.44 412.7 L24.37 412.7 L24.37 412.16 L23.44 412.16 L23.44 412.7
+							 ZM23.44 413.39 L24.37 413.39 L24.37 412.84 L23.44 412.84 L23.44 413.39 ZM22.22 413.39 L23.16 413.39
+							 L23.16 412.84 L22.22 412.84 L22.22 413.39 Z" class="st10"/>
+			</g>
+			<g id="shape33-160" transform="translate(-391.623,414.188) rotate(-90)">
+				<title>Sheet.33</title>
+				<path d="M0 410.93 L0.94 410.93 L0.94 410.39 L0 410.39 L0 410.93 ZM0 412.7 L1.5 412.7 L1.5 412.16 L0 412.16 L0 412.7
+							 ZM0 413.39 L1.5 413.39 L1.5 412.84 L0 412.84 L0 413.39 ZM0 414.07 L1.5 414.07 L1.5 413.52 L0 413.52
+							 L0 414.07 ZM0 414.75 L1.5 414.75 L1.5 414.2 L0 414.2 L0 414.75 ZM1.69 414.75 L2.63 414.75 L2.63 414.2
+							 L1.69 414.2 L1.69 414.75 ZM2.81 414.75 L3.75 414.75 L3.75 414.2 L2.81 414.2 L2.81 414.75 ZM11.81 414.75
+							 L12.75 414.75 L12.75 414.2 L11.81 414.2 L11.81 414.75 ZM12.94 414.75 L13.87 414.75 L13.87 414.2 L12.94
+							 414.2 L12.94 414.75 ZM14.06 414.75 L15 414.75 L15 414.2 L14.06 414.2 L14.06 414.75 ZM15.19 414.75 L16.69
+							 414.75 L16.69 414.2 L15.19 414.2 L15.19 414.75 ZM17.25 414.75 L18.19 414.75 L18.19 414.2 L17.25 414.2
+							 L17.25 414.75 ZM18.37 414.75 L19.31 414.75 L19.31 414.2 L18.37 414.2 L18.37 414.75 ZM19.5 414.75 L20.44
+							 414.75 L20.44 414.2 L19.5 414.2 L19.5 414.75 ZM24.66 414.75 L25.59 414.75 L25.59 413.55 L24.66 413.55
+							 L24.66 414.75 ZM24.66 413.44 L25.59 413.44 L25.59 412.16 L24.66 412.16 L24.66 413.44 ZM24.66 412.02
+							 L25.59 412.02 L25.59 411.48 L24.66 411.48 L24.66 412.02 ZM23.44 412.02 L24.37 412.02 L24.37 411.48 L23.44
+							 411.48 L23.44 412.02 ZM22.22 412.02 L23.16 412.02 L23.16 411.48 L22.22 411.48 L22.22 412.02 ZM21 412.02
+							 L21.94 412.02 L21.94 411.48 L21 411.48 L21 412.02 ZM19.5 412.02 L20.44 412.02 L20.44 411.48 L19.5 411.48
+							 L19.5 412.02 ZM19.5 412.7 L20.44 412.7 L20.44 412.16 L19.5 412.16 L19.5 412.7 ZM18.37 414.07 L19.31
+							 414.07 L19.31 413.52 L18.37 413.52 L18.37 414.07 ZM14.06 414.06 L16.69 414.06 L16.69 413.51 L14.06 413.51
+							 L14.06 414.06 ZM15.19 413.37 L16.69 413.37 L16.69 412.17 L15.19 412.17 L15.19 413.37 ZM17.25 412.7 L18.19
+							 412.7 L18.19 412.16 L17.25 412.16 L17.25 412.7 ZM18.37 412.7 L19.31 412.7 L19.31 412.16 L18.37 412.16
+							 L18.37 412.7 ZM18.37 412.02 L19.31 412.02 L19.31 411.48 L18.37 411.48 L18.37 412.02 ZM15.19 412.02 L16.69
+							 412.02 L16.69 411.48 L15.19 411.48 L15.19 412.02 ZM24.19 410.6 L24.94 410.6 L24.94 410.5 L24.19 410.5
+							 L24.19 410.6 ZM23.06 410.6 L23.81 410.6 L23.81 410.5 L23.06 410.5 L23.06 410.6 ZM19.5 410.93 L20.44
+							 410.93 L20.44 410.39 L19.5 410.39 L19.5 410.93 ZM18.37 410.93 L19.31 410.93 L19.31 410.39 L18.37 410.39
+							 L18.37 410.93 ZM17.25 410.93 L18.19 410.93 L18.19 410.39 L17.25 410.39 L17.25 410.93 ZM10.31 410.93
+							 L11.25 410.93 L11.25 410.39 L10.31 410.39 L10.31 410.93 ZM9.19 410.93 L10.12 410.93 L10.12 410.39 L9.19
+							 410.39 L9.19 410.93 ZM8.06 410.93 L9 410.93 L9 410.39 L8.06 410.39 L8.06 410.93 ZM6.94 410.93 L7.87
+							 410.93 L7.87 410.39 L6.94 410.39 L6.94 410.93 ZM17.25 412.02 L18.19 412.02 L18.19 411.48 L17.25 411.48
+							 L17.25 412.02 Z" class="st11"/>
+			</g>
+		</g>
+		<g id="shape35-162" transform="translate(359.23,-270.375)">
+			<title>Sheet.35</title>
+			<path d="M0 414.75 L27.34 414.75" class="st4"/>
+		</g>
+		<g id="shape55-167" transform="translate(360.375,-324.375)">
+			<title>Sheet.55</title>
+			<desc>RS-232</desc>
+			<rect x="0" y="405.75" width="27" height="9" class="st12"/>
+			<text x="4.91" y="412.05" class="st14">RS-232</text>		</g>
+		<g id="shape63-170" transform="translate(359.311,-270.375)">
+			<title>Sheet.63</title>
+			<desc>RS-232</desc>
+			<rect x="0" y="405.75" width="27" height="9" class="st12"/>
+			<text x="4.91" y="412.05" class="st14">RS-232</text>		</g>
+		<g id="shape64-173" transform="translate(360.375,-108.375)">
+			<title>Sheet.64</title>
+			<desc>VGA</desc>
+			<rect x="0" y="405.75" width="27" height="9" class="st12"/>
+			<text x="8" y="412.05" class="st14">VGA</text>		</g>
+		<g id="shape65-176" transform="translate(360.375,-72.375)">
+			<title>Sheet.65</title>
+			<desc>VGA</desc>
+			<rect x="0" y="405.75" width="27" height="9" class="st12"/>
+			<text x="8" y="412.05" class="st14">VGA</text>		</g>
+		<g id="shape66-179" transform="translate(360.375,-36.375)">
+			<title>Sheet.66</title>
+			<desc>NTSC</desc>
+			<rect x="0" y="405.75" width="27" height="9" class="st12"/>
+			<text x="7.03" y="412.05" class="st14">NTSC</text>		</g>
+		<g id="shape67-182" transform="translate(108.375,-297.375)">
+			<title>Sheet.67</title>
+			<desc>UART</desc>
+			<rect x="0" y="396.75" width="54" height="18" class="st1"/>
+			<text x="15.42" y="408.75" class="st2">UART</text>		</g>
+		<g id="shape68-185" transform="translate(108.375,-279.375)">
+			<title>Sheet.68</title>
+			<desc>ASCI</desc>
+			<rect x="0" y="396.75" width="54" height="18" class="st1"/>
+			<text x="17.63" y="408.75" class="st2">ASCI</text>		</g>
+		<g id="shape69-188" transform="translate(108.375,-261.375)">
+			<title>Sheet.69</title>
+			<desc>VDU</desc>
+			<rect x="0" y="396.75" width="54" height="18" class="st1"/>
+			<text x="17.63" y="408.75" class="st2">VDU</text>		</g>
+		<g id="shape74-191" transform="translate(189.375,-81.375)">
+			<title>Sheet.74</title>
+			<desc>SY6545</desc>
+			<rect x="0" y="396.75" width="54" height="18" class="st1"/>
+			<text x="11.9" y="408.75" class="st2">SY6545</text>		</g>
+		<g id="shape75-194" transform="translate(189.375,-63.375)">
+			<title>Sheet.75</title>
+			<desc>MC8563</desc>
+			<rect x="0" y="396.75" width="54" height="18" class="st1"/>
+			<text x="9.85" y="408.75" class="st2">MC8563</text>		</g>
+		<g id="shape76-197" transform="translate(189.375,-45.375)">
+			<title>Sheet.76</title>
+			<desc>uPD7220</desc>
+			<rect x="0" y="396.75" width="54" height="18" class="st1"/>
+			<text x="8.37" y="408.75" class="st2">uPD7220</text>		</g>
+		<g id="shape79-200" transform="translate(0.375,-396.375)">
+			<title>Sheet.79</title>
+			<desc>Character / Emulation / Video Services</desc>
+			<rect x="0" y="396.75" width="432" height="18" class="st1"/>
+			<text x="103.64" y="409.95" class="st15">Character / Emulation / Video Services</text>		</g>
+		<g id="shape82-203" transform="translate(54.375,-360.375)">
+			<title>Sheet.82</title>
+			<desc>HBIOS</desc>
+			<rect x="0" y="396.75" width="225" height="18" class="st12"/>
+			<text x="99.47" y="408.75" class="st2">HBIOS</text>		</g>
+		<g id="shape83-206" transform="translate(297.375,-360.375)">
+			<title>Sheet.83</title>
+			<desc>HARDWARE</desc>
+			<rect x="0" y="396.75" width="135" height="18" class="st12"/>
+			<text x="42.53" y="408.75" class="st2">HARDWARE</text>		</g>
+		<g id="shape84-209" transform="translate(189.375,-27.375)">
+			<title>Sheet.84</title>
+			<desc>TMS9918</desc>
+			<rect x="0" y="396.75" width="54" height="18" class="st1"/>
+			<text x="7.65" y="408.75" class="st2">TMS9918</text>		</g>
+		<g id="group87-212" transform="translate(395.311,-130.875)">
+			<title>Terminal.87</title>
+			<g id="shape88-213" transform="translate(-391.186,414.75) rotate(-90)">
+				<title>Sheet.88</title>
+				<path d="M0 414.75 L27 414.75 L27 409.08 L0 409.08 L0 414.75 ZM26.25 403.93 L23.44 399.37 L3.53 399.37 L0.75 403.93
+							 L26.25 403.93 ZM23.44 399.37 L23.44 391.19 L3.53 391.19 L3.53 399.37 L23.44 399.37 ZM26.25 407.7 L26.25
+							 403.93 L0.75 403.93 L0.75 407.7 L26.25 407.7 ZM24.83 407.7 A1223.48 394.162 90 0 1 2.17 407.7 L24.83
+							 407.7 Z" class="st8"/>
+			</g>
+			<g id="shape89-215" transform="translate(-395.768,392.25) rotate(-90)">
+				<title>Sheet.89</title>
+				<rect x="0" y="414.641" width="0.75" height="0.109091" class="st9"/>
+			</g>
+			<g id="shape90-217" transform="translate(-391.623,414.188) rotate(-90)">
+				<title>Sheet.90</title>
+				<path d="M1.69 410.93 L2.63 410.93 L2.63 410.39 L1.69 410.39 L1.69 410.93 ZM2.81 410.93 L3.75 410.93 L3.75 410.39
+							 L2.81 410.39 L2.81 410.93 ZM3.94 410.93 L4.87 410.93 L4.87 410.39 L3.94 410.39 L3.94 410.93 ZM5.06 410.93
+							 L6 410.93 L6 410.39 L5.06 410.39 L5.06 410.93 ZM12.28 410.93 L13.22 410.93 L13.22 410.39 L12.28 410.39
+							 L12.28 410.93 ZM13.41 410.93 L14.34 410.93 L14.34 410.39 L13.41 410.39 L13.41 410.93 ZM14.53 410.93
+							 L15.47 410.93 L15.47 410.39 L14.53 410.39 L14.53 410.93 ZM15.66 410.93 L16.59 410.93 L16.59 410.39 L15.66
+							 410.39 L15.66 410.93 ZM0 412.02 L1.5 412.02 L1.5 411.48 L0 411.48 L0 412.02 ZM1.69 412.02 L2.63 412.02
+							 L2.63 411.48 L1.69 411.48 L1.69 412.02 ZM2.81 412.02 L3.75 412.02 L3.75 411.48 L2.81 411.48 L2.81 412.02
+							 ZM3.94 412.02 L4.87 412.02 L4.87 411.48 L3.94 411.48 L3.94 412.02 ZM5.06 412.02 L6 412.02 L6 411.48
+							 L5.06 411.48 L5.06 412.02 ZM6.19 412.02 L7.12 412.02 L7.12 411.48 L6.19 411.48 L6.19 412.02 ZM7.31 412.02
+							 L8.25 412.02 L8.25 411.48 L7.31 411.48 L7.31 412.02 ZM8.44 412.02 L9.37 412.02 L9.37 411.48 L8.44 411.48
+							 L8.44 412.02 ZM9.56 412.02 L10.5 412.02 L10.5 411.48 L9.56 411.48 L9.56 412.02 ZM10.69 412.02 L11.62
+							 412.02 L11.62 411.48 L10.69 411.48 L10.69 412.02 ZM11.81 412.02 L12.75 412.02 L12.75 411.48 L11.81 411.48
+							 L11.81 412.02 ZM12.94 412.02 L13.87 412.02 L13.87 411.48 L12.94 411.48 L12.94 412.02 ZM14.06 412.02
+							 L15 412.02 L15 411.48 L14.06 411.48 L14.06 412.02 ZM1.69 412.7 L2.63 412.7 L2.63 412.16 L1.69 412.16
+							 L1.69 412.7 ZM2.81 412.7 L3.75 412.7 L3.75 412.16 L2.81 412.16 L2.81 412.7 ZM3.94 412.7 L4.87 412.7
+							 L4.87 412.16 L3.94 412.16 L3.94 412.7 ZM5.06 412.7 L6 412.7 L6 412.16 L5.06 412.16 L5.06 412.7 ZM6.19
+							 412.7 L7.12 412.7 L7.12 412.16 L6.19 412.16 L6.19 412.7 ZM7.31 412.7 L8.25 412.7 L8.25 412.16 L7.31
+							 412.16 L7.31 412.7 ZM8.44 412.7 L9.37 412.7 L9.37 412.16 L8.44 412.16 L8.44 412.7 ZM9.56 412.7 L10.5
+							 412.7 L10.5 412.16 L9.56 412.16 L9.56 412.7 ZM10.69 412.7 L11.62 412.7 L11.62 412.16 L10.69 412.16 L10.69
+							 412.7 ZM11.81 412.7 L12.75 412.7 L12.75 412.16 L11.81 412.16 L11.81 412.7 ZM12.94 412.7 L13.87 412.7
+							 L13.87 412.16 L12.94 412.16 L12.94 412.7 ZM14.06 412.7 L15 412.7 L15 412.16 L14.06 412.16 L14.06 412.7
+							 ZM1.69 413.39 L2.63 413.39 L2.63 412.84 L1.69 412.84 L1.69 413.39 ZM2.81 413.39 L3.75 413.39 L3.75 412.84
+							 L2.81 412.84 L2.81 413.39 ZM3.94 413.39 L4.87 413.39 L4.87 412.84 L3.94 412.84 L3.94 413.39 ZM5.06 413.39
+							 L6 413.39 L6 412.84 L5.06 412.84 L5.06 413.39 ZM6.19 413.39 L7.12 413.39 L7.12 412.84 L6.19 412.84 L6.19
+							 413.39 ZM7.31 413.39 L8.25 413.39 L8.25 412.84 L7.31 412.84 L7.31 413.39 ZM8.44 413.39 L9.37 413.39
+							 L9.37 412.84 L8.44 412.84 L8.44 413.39 ZM9.56 413.39 L10.5 413.39 L10.5 412.84 L9.56 412.84 L9.56 413.39
+							 ZM10.69 413.39 L11.62 413.39 L11.62 412.84 L10.69 412.84 L10.69 413.39 ZM11.81 413.39 L12.75 413.39
+							 L12.75 412.84 L11.81 412.84 L11.81 413.39 ZM12.94 413.39 L13.87 413.39 L13.87 412.84 L12.94 412.84 L12.94
+							 413.39 ZM14.06 413.39 L15 413.39 L15 412.84 L14.06 412.84 L14.06 413.39 ZM1.69 414.07 L2.63 414.07 L2.63
+							 413.52 L1.69 413.52 L1.69 414.07 ZM2.81 414.07 L3.75 414.07 L3.75 413.52 L2.81 413.52 L2.81 414.07 ZM3.94
+							 414.07 L4.87 414.07 L4.87 413.52 L3.94 413.52 L3.94 414.07 ZM5.06 414.07 L6 414.07 L6 413.52 L5.06 413.52
+							 L5.06 414.07 ZM6.19 414.07 L7.12 414.07 L7.12 413.52 L6.19 413.52 L6.19 414.07 ZM7.31 414.07 L8.25 414.07
+							 L8.25 413.52 L7.31 413.52 L7.31 414.07 ZM8.44 414.07 L9.37 414.07 L9.37 413.52 L8.44 413.52 L8.44 414.07
+							 ZM9.56 414.07 L10.5 414.07 L10.5 413.52 L9.56 413.52 L9.56 414.07 ZM10.69 414.07 L11.62 414.07 L11.62
+							 413.52 L10.69 413.52 L10.69 414.07 ZM11.81 414.07 L12.75 414.07 L12.75 413.52 L11.81 413.52 L11.81 414.07
+							 ZM12.94 414.07 L13.87 414.07 L13.87 413.52 L12.94 413.52 L12.94 414.07 ZM3.94 414.75 L11.62 414.75 L11.62
+							 414.2 L3.94 414.2 L3.94 414.75 ZM21 414.75 L23.25 414.75 L23.25 414.2 L21 414.2 L21 414.75 ZM23.44 414.75
+							 L24.37 414.75 L24.37 414.2 L23.44 414.2 L23.44 414.75 ZM23.44 414.07 L24.37 414.07 L24.37 413.52 L23.44
+							 413.52 L23.44 414.07 ZM22.22 414.07 L23.16 414.07 L23.16 413.52 L22.22 413.52 L22.22 414.07 ZM21 414.07
+							 L21.94 414.07 L21.94 413.52 L21 413.52 L21 414.07 ZM21 413.39 L21.94 413.39 L21.94 412.84 L21 412.84
+							 L21 413.39 ZM21 412.7 L21.94 412.7 L21.94 412.16 L21 412.16 L21 412.7 ZM22.22 412.7 L23.16 412.7 L23.16
+							 412.16 L22.22 412.16 L22.22 412.7 ZM23.44 412.7 L24.37 412.7 L24.37 412.16 L23.44 412.16 L23.44 412.7
+							 ZM23.44 413.39 L24.37 413.39 L24.37 412.84 L23.44 412.84 L23.44 413.39 ZM22.22 413.39 L23.16 413.39
+							 L23.16 412.84 L22.22 412.84 L22.22 413.39 Z" class="st10"/>
+			</g>
+			<g id="shape91-219" transform="translate(-391.623,414.188) rotate(-90)">
+				<title>Sheet.91</title>
+				<path d="M0 410.93 L0.94 410.93 L0.94 410.39 L0 410.39 L0 410.93 ZM0 412.7 L1.5 412.7 L1.5 412.16 L0 412.16 L0 412.7
+							 ZM0 413.39 L1.5 413.39 L1.5 412.84 L0 412.84 L0 413.39 ZM0 414.07 L1.5 414.07 L1.5 413.52 L0 413.52
+							 L0 414.07 ZM0 414.75 L1.5 414.75 L1.5 414.2 L0 414.2 L0 414.75 ZM1.69 414.75 L2.63 414.75 L2.63 414.2
+							 L1.69 414.2 L1.69 414.75 ZM2.81 414.75 L3.75 414.75 L3.75 414.2 L2.81 414.2 L2.81 414.75 ZM11.81 414.75
+							 L12.75 414.75 L12.75 414.2 L11.81 414.2 L11.81 414.75 ZM12.94 414.75 L13.87 414.75 L13.87 414.2 L12.94
+							 414.2 L12.94 414.75 ZM14.06 414.75 L15 414.75 L15 414.2 L14.06 414.2 L14.06 414.75 ZM15.19 414.75 L16.69
+							 414.75 L16.69 414.2 L15.19 414.2 L15.19 414.75 ZM17.25 414.75 L18.19 414.75 L18.19 414.2 L17.25 414.2
+							 L17.25 414.75 ZM18.37 414.75 L19.31 414.75 L19.31 414.2 L18.37 414.2 L18.37 414.75 ZM19.5 414.75 L20.44
+							 414.75 L20.44 414.2 L19.5 414.2 L19.5 414.75 ZM24.66 414.75 L25.59 414.75 L25.59 413.55 L24.66 413.55
+							 L24.66 414.75 ZM24.66 413.44 L25.59 413.44 L25.59 412.16 L24.66 412.16 L24.66 413.44 ZM24.66 412.02
+							 L25.59 412.02 L25.59 411.48 L24.66 411.48 L24.66 412.02 ZM23.44 412.02 L24.37 412.02 L24.37 411.48 L23.44
+							 411.48 L23.44 412.02 ZM22.22 412.02 L23.16 412.02 L23.16 411.48 L22.22 411.48 L22.22 412.02 ZM21 412.02
+							 L21.94 412.02 L21.94 411.48 L21 411.48 L21 412.02 ZM19.5 412.02 L20.44 412.02 L20.44 411.48 L19.5 411.48
+							 L19.5 412.02 ZM19.5 412.7 L20.44 412.7 L20.44 412.16 L19.5 412.16 L19.5 412.7 ZM18.37 414.07 L19.31
+							 414.07 L19.31 413.52 L18.37 413.52 L18.37 414.07 ZM14.06 414.06 L16.69 414.06 L16.69 413.51 L14.06 413.51
+							 L14.06 414.06 ZM15.19 413.37 L16.69 413.37 L16.69 412.17 L15.19 412.17 L15.19 413.37 ZM17.25 412.7 L18.19
+							 412.7 L18.19 412.16 L17.25 412.16 L17.25 412.7 ZM18.37 412.7 L19.31 412.7 L19.31 412.16 L18.37 412.16
+							 L18.37 412.7 ZM18.37 412.02 L19.31 412.02 L19.31 411.48 L18.37 411.48 L18.37 412.02 ZM15.19 412.02 L16.69
+							 412.02 L16.69 411.48 L15.19 411.48 L15.19 412.02 ZM24.19 410.6 L24.94 410.6 L24.94 410.5 L24.19 410.5
+							 L24.19 410.6 ZM23.06 410.6 L23.81 410.6 L23.81 410.5 L23.06 410.5 L23.06 410.6 ZM19.5 410.93 L20.44
+							 410.93 L20.44 410.39 L19.5 410.39 L19.5 410.93 ZM18.37 410.93 L19.31 410.93 L19.31 410.39 L18.37 410.39
+							 L18.37 410.93 ZM17.25 410.93 L18.19 410.93 L18.19 410.39 L17.25 410.39 L17.25 410.93 ZM10.31 410.93
+							 L11.25 410.93 L11.25 410.39 L10.31 410.39 L10.31 410.93 ZM9.19 410.93 L10.12 410.93 L10.12 410.39 L9.19
+							 410.39 L9.19 410.93 ZM8.06 410.93 L9 410.93 L9 410.39 L8.06 410.39 L8.06 410.93 ZM6.94 410.93 L7.87
+							 410.93 L7.87 410.39 L6.94 410.39 L6.94 410.93 ZM17.25 412.02 L18.19 412.02 L18.19 411.48 L17.25 411.48
+							 L17.25 412.02 Z" class="st11"/>
+			</g>
+		</g>
+		<g id="shape92-221" transform="translate(314.311,-135.375)">
+			<title>Sheet.92</title>
+			<desc>VDU</desc>
+			<rect x="0" y="396.75" width="44.9182" height="18" class="st6"/>
+			<text x="14.96" y="408.15" class="st7">VDU</text>		</g>
+		<g id="shape93-224" transform="translate(359.23,-144.375)">
+			<title>Sheet.93</title>
+			<path d="M0 414.75 L26.27 414.75" class="st4"/>
+		</g>
+		<g id="shape94-229" transform="translate(359.311,-144.375)">
+			<title>Sheet.94</title>
+			<desc>NTSC</desc>
+			<rect x="0" y="405.75" width="27" height="9" class="st12"/>
+			<text x="7.03" y="412.05" class="st14">NTSC</text>		</g>
+		<g id="shape96-232" transform="translate(243.375,-90.375)">
+			<title>Sheet.96</title>
+			<path d="M0 414.75 L4.05 414.75 A4.05 4.05 -180 0 0 8.1 410.7 L8.1 365.25 A4.5 4.5 0 0 1 12.6 360.75 L61.13 360.75"
+					class="st4"/>
+		</g>
+		<g id="shape7-237" transform="translate(243.375,-72.375)">
+			<title>Sheet.7</title>
+			<path d="M0 414.75 L13.5 414.75 A4.5 4.5 -180 0 0 18 410.25 L18 383.25 A4.5 4.5 0 0 1 22.5 378.75 L62.19 378.75"
+					class="st4"/>
+		</g>
+		<g id="shape17-242" transform="translate(243.375,-54.375)">
+			<title>Sheet.17</title>
+			<path d="M0 414.75 L22.5 414.75 A4.5 4.5 -180 0 0 27 410.25 L27 401.25 A4.5 4.5 0 0 1 31.5 396.75 L62.19 396.75"
+					class="st4"/>
+		</g>
+		<g id="shape3-247" transform="translate(162.375,-306.375)">
+			<title>Sheet.3</title>
+			<path d="M0 414.75 L31.5 414.75 A4.5 4.5 -180 0 0 36 410.25 L36 401.25 A4.5 4.5 0 0 1 40.5 396.75 L143.19 396.75"
+					class="st4"/>
+		</g>
+		<g id="shape4-252" transform="translate(162.375,-270.375)">
+			<title>Sheet.4</title>
+			<path d="M0 396.75 L31.5 396.75 A4.5 4.5 0 0 1 36 401.25 L36 410.25 A4.5 4.5 -180 0 0 40.5 414.75 L142.13 414.75"
+					class="st4"/>
+		</g>
+	</g>
+</svg>

Source/Doc/Graphics/Logo.svg

@@ -1,15 +1,9 @@
 <?xml version="1.0" encoding="UTF-8" standalone="no"?>
 <!DOCTYPE svg PUBLIC "-//W3C//DTD SVG 1.1//EN" "http://www.w3.org/Graphics/SVG/1.1/DTD/svg11.dtd">
-<!-- Generated by Microsoft Visio, SVG Export WBW.svg Page-1 -->
+<!-- Generated by Microsoft Visio, SVG Export Logo.svg Page-1 -->
 <svg xmlns="http://www.w3.org/2000/svg" xmlns:xlink="http://www.w3.org/1999/xlink" xmlns:ev="http://www.w3.org/2001/xml-events"
-		xmlns:v="http://schemas.microsoft.com/visio/2003/SVGExtensions/" width="8.5in" height="11in" viewBox="0 0 612 792"
-		xml:space="preserve" color-interpolation-filters="sRGB" class="st3">
-	<v:documentProperties v:langID="1033" v:viewMarkup="false">
-		<v:userDefs>
-			<v:ud v:nameU="msvNoAutoConnect" v:val="VT0(1):26"/>
-		</v:userDefs>
-	</v:documentProperties>
-
+		width="3.76042in" height="1.26042in" viewBox="0 0 270.75 90.75" xml:space="preserve" color-interpolation-filters="sRGB"
+		class="st3">
 	<style type="text/css">
 	<![CDATA[
 		.st1 {fill:#4bacc6;stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-opacity:0;stroke-width:0.75}
@@ -18,52 +12,51 @@
 	]]>
 	</style>
 
-	<g v:mID="0" v:index="1" v:groupContext="foregroundPage">
+	<g>
 		<title>Page-1</title>
-		<v:pageProperties v:drawingScale="1" v:pageScale="1" v:drawingUnits="19" v:shadowOffsetX="9" v:shadowOffsetY="-9"/>
-		<g id="shape34-1" v:mID="34" v:groupContext="shape" transform="translate(18,-684)">
+		<g id="shape34-1" transform="translate(0.375,-0.375)">
 			<title>Sheet.34</title>
-			<rect x="0" y="702" width="18" height="90" rx="9" ry="9" class="st1"/>
+			<rect x="0" y="0.75" width="18" height="90" rx="9" ry="9" class="st1"/>
 		</g>
-		<g id="shape35-3" v:mID="35" v:groupContext="shape" transform="translate(54,-684)">
+		<g id="shape35-3" transform="translate(36.375,-0.375)">
 			<title>Sheet.35</title>
-			<rect x="0" y="738" width="18" height="54" rx="9" ry="9" class="st1"/>
+			<rect x="0" y="36.75" width="18" height="54" rx="9" ry="9" class="st1"/>
 		</g>
-		<g id="shape36-5" v:mID="36" v:groupContext="shape" transform="translate(90,-684)">
+		<g id="shape36-5" transform="translate(72.375,-0.375)">
 			<title>Sheet.36</title>
-			<rect x="0" y="702" width="18" height="90" rx="9" ry="9" class="st1"/>
+			<rect x="0" y="0.75" width="18" height="90" rx="9" ry="9" class="st1"/>
 		</g>
-		<g id="shape38-7" v:mID="38" v:groupContext="shape" transform="translate(234,-684)">
+		<g id="shape38-7" transform="translate(216.375,-0.375)">
 			<title>Sheet.38</title>
-			<rect x="0" y="738" width="18" height="54" rx="9" ry="9" class="st1"/>
+			<rect x="0" y="36.75" width="18" height="54" rx="9" ry="9" class="st1"/>
 		</g>
-		<g id="shape39-9" v:mID="39" v:groupContext="shape" transform="translate(270,-684)">
+		<g id="shape39-9" transform="translate(252.375,-0.375)">
 			<title>Sheet.39</title>
-			<rect x="0" y="702" width="18" height="90" rx="9" ry="9" class="st1"/>
+			<rect x="0" y="0.75" width="18" height="90" rx="9" ry="9" class="st1"/>
 		</g>
-		<g id="shape44-11" v:mID="44" v:groupContext="shape" transform="translate(198,-684)">
+		<g id="shape44-11" transform="translate(180.375,-0.375)">
 			<title>Sheet.44</title>
-			<rect x="0" y="702" width="18" height="90" rx="9" ry="9" class="st1"/>
+			<rect x="0" y="0.75" width="18" height="90" rx="9" ry="9" class="st1"/>
 		</g>
-		<g id="shape48-13" v:mID="48" v:groupContext="shape" transform="translate(126,-756)">
+		<g id="shape48-13" transform="translate(108.375,-72.375)">
 			<title>Sheet.48</title>
-			<rect x="0" y="774" width="36" height="18" rx="9" ry="9" class="st1"/>
+			<rect x="0" y="72.75" width="36" height="18" rx="9" ry="9" class="st1"/>
 		</g>
-		<g id="shape49-15" v:mID="49" v:groupContext="shape" transform="translate(126,-720)">
+		<g id="shape49-15" transform="translate(108.375,-36.375)">
 			<title>Sheet.49</title>
-			<rect x="0" y="774" width="36" height="18" rx="9" ry="9" class="st1"/>
+			<rect x="0" y="72.75" width="36" height="18" rx="9" ry="9" class="st1"/>
 		</g>
-		<g id="shape50-17" v:mID="50" v:groupContext="shape" transform="translate(126,-684)">
+		<g id="shape50-17" transform="translate(108.375,-0.375)">
 			<title>Sheet.50</title>
-			<rect x="0" y="774" width="36" height="18" rx="9" ry="9" class="st1"/>
+			<rect x="0" y="72.75" width="36" height="18" rx="9" ry="9" class="st1"/>
 		</g>
-		<g id="shape52-19" v:mID="52" v:groupContext="shape" transform="translate(153,-729)">
+		<g id="shape52-19" transform="translate(135.375,-45.375)">
 			<title>Sheet.52</title>
-			<path d="M-0 756 A18 18 0 0 1 18 774 A18 18 0 0 1 -0 792" class="st2"/>
+			<path d="M-0 54.75 A18 18 0 0 1 18 72.75 A18 18 0 0 1 -0 90.75" class="st2"/>
 		</g>
-		<g id="shape53-22" v:mID="53" v:groupContext="shape" transform="translate(153,-693)">
+		<g id="shape53-22" transform="translate(135.375,-9.375)">
 			<title>Sheet.53</title>
-			<path d="M-0 756 A18 18 0 0 1 18 774 A18 18 0 0 1 -0 792" class="st2"/>
+			<path d="M-0 54.75 A18 18 0 0 1 18 72.75 A18 18 0 0 1 -0 90.75" class="st2"/>
 		</g>
 	</g>
 </svg>

Source/Doc/Graphics/Panel.svg

@@ -0,0 +1,369 @@
+<?xml version="1.0" encoding="UTF-8" standalone="no"?>
+<!DOCTYPE svg PUBLIC "-//W3C//DTD SVG 1.1//EN" "http://www.w3.org/Graphics/SVG/1.1/DTD/svg11.dtd">
+<!-- Generated by Microsoft Visio, SVG Export Panel.svg Page-1 -->
+<svg xmlns="http://www.w3.org/2000/svg" xmlns:xlink="http://www.w3.org/1999/xlink" xmlns:ev="http://www.w3.org/2001/xml-events"
+		width="4.51042in" height="2.51042in" viewBox="0 0 324.75 180.75" xml:space="preserve" color-interpolation-filters="sRGB"
+		class="st11">
+	<style type="text/css">
+	<![CDATA[
+		.st1 {fill:#ff0000;stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.75}
+		.st2 {fill:#7f7f7f;stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.75}
+		.st3 {fill:#000000;stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.75}
+		.st4 {stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:2}
+		.st5 {fill:none;stroke:none;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.75}
+		.st6 {fill:#000000;font-family:Calibri;font-size:1.00001em}
+		.st7 {stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.75}
+		.st8 {fill:#000000;font-family:Calibri;font-size:0.666664em}
+		.st9 {fill:#000000;font-family:Calibri;font-size:0.499992em}
+		.st10 {fill:none;stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.75}
+		.st11 {fill:none;fill-rule:evenodd;font-size:12px;overflow:visible;stroke-linecap:square;stroke-miterlimit:3}
+	]]>
+	</style>
+
+	<g>
+		<title>Page-1</title>
+		<g id="shape1-1" transform="translate(27.375,-117.375)">
+			<title>Sheet.1</title>
+			<ellipse cx="9" cy="171.75" rx="9" ry="9.00001" class="st1"/>
+		</g>
+		<g id="shape2-3" transform="translate(99.375,-27.375)">
+			<title>Sheet.2</title>
+			<ellipse cx="9" cy="171.75" rx="9" ry="9.00001" class="st2"/>
+		</g>
+		<g id="shape3-5" transform="translate(106.125,-18.375)">
+			<title>Sheet.3</title>
+			<rect x="0" y="160.5" width="4.5" height="20.25" rx="2.25" ry="2.25" class="st3"/>
+		</g>
+		<g id="shape8-7" transform="translate(63.375,-117.375)">
+			<title>Sheet.8</title>
+			<ellipse cx="9" cy="171.75" rx="9" ry="9.00001" class="st1"/>
+		</g>
+		<g id="shape9-9" transform="translate(99.375,-117.375)">
+			<title>Sheet.9</title>
+			<ellipse cx="9" cy="171.75" rx="9" ry="9.00001" class="st1"/>
+		</g>
+		<g id="shape10-11" transform="translate(135.375,-117.375)">
+			<title>Sheet.10</title>
+			<ellipse cx="9" cy="171.75" rx="9" ry="9.00001" class="st1"/>
+		</g>
+		<g id="shape11-13" transform="translate(171.375,-117.375)">
+			<title>Sheet.11</title>
+			<ellipse cx="9" cy="171.75" rx="9" ry="9.00001" class="st1"/>
+		</g>
+		<g id="shape12-15" transform="translate(207.375,-117.375)">
+			<title>Sheet.12</title>
+			<ellipse cx="9" cy="171.75" rx="9" ry="9.00001" class="st1"/>
+		</g>
+		<g id="shape13-17" transform="translate(243.375,-117.375)">
+			<title>Sheet.13</title>
+			<ellipse cx="9" cy="171.75" rx="9" ry="9.00001" class="st1"/>
+		</g>
+		<g id="shape14-19" transform="translate(279.375,-117.375)">
+			<title>Sheet.14</title>
+			<ellipse cx="9" cy="171.75" rx="9" ry="9.00001" class="st1"/>
+		</g>
+		<g id="shape18-21" transform="translate(27.375,-27.375)">
+			<title>Sheet.18</title>
+			<ellipse cx="9" cy="171.75" rx="9" ry="9.00001" class="st2"/>
+		</g>
+		<g id="shape19-23" transform="translate(34.125,-18.375)">
+			<title>Sheet.19</title>
+			<rect x="0" y="160.5" width="4.5" height="20.25" rx="2.25" ry="2.25" class="st3"/>
+		</g>
+		<g id="shape20-25" transform="translate(63.375,-27.375)">
+			<title>Sheet.20</title>
+			<ellipse cx="9" cy="171.75" rx="9" ry="9.00001" class="st2"/>
+		</g>
+		<g id="shape21-27" transform="translate(70.125,-18.375)">
+			<title>Sheet.21</title>
+			<rect x="0" y="160.5" width="4.5" height="20.25" rx="2.25" ry="2.25" class="st3"/>
+		</g>
+		<g id="shape22-29" transform="translate(135.375,-27.375)">
+			<title>Sheet.22</title>
+			<ellipse cx="9" cy="171.75" rx="9" ry="9.00001" class="st2"/>
+		</g>
+		<g id="shape23-31" transform="translate(142.125,-18.375)">
+			<title>Sheet.23</title>
+			<rect x="0" y="160.5" width="4.5" height="20.25" rx="2.25" ry="2.25" class="st3"/>
+		</g>
+		<g id="shape24-33" transform="translate(171.375,-27.375)">
+			<title>Sheet.24</title>
+			<ellipse cx="9" cy="171.75" rx="9" ry="9.00001" class="st2"/>
+		</g>
+		<g id="shape25-35" transform="translate(178.125,-18.375)">
+			<title>Sheet.25</title>
+			<rect x="0" y="160.5" width="4.5" height="20.25" rx="2.25" ry="2.25" class="st3"/>
+		</g>
+		<g id="shape26-37" transform="translate(207.375,-27.375)">
+			<title>Sheet.26</title>
+			<ellipse cx="9" cy="171.75" rx="9" ry="9.00001" class="st2"/>
+		</g>
+		<g id="shape27-39" transform="translate(214.125,-18.375)">
+			<title>Sheet.27</title>
+			<rect x="0" y="160.5" width="4.5" height="20.25" rx="2.25" ry="2.25" class="st3"/>
+		</g>
+		<g id="shape28-41" transform="translate(243.375,-27.375)">
+			<title>Sheet.28</title>
+			<ellipse cx="9" cy="171.75" rx="9" ry="9.00001" class="st2"/>
+		</g>
+		<g id="shape29-43" transform="translate(250.125,-18.375)">
+			<title>Sheet.29</title>
+			<rect x="0" y="160.5" width="4.5" height="20.25" rx="2.25" ry="2.25" class="st3"/>
+		</g>
+		<g id="shape30-45" transform="translate(279.375,-27.375)">
+			<title>Sheet.30</title>
+			<ellipse cx="9" cy="171.75" rx="9" ry="9.00001" class="st2"/>
+		</g>
+		<g id="shape31-47" transform="translate(286.125,-18.375)">
+			<title>Sheet.31</title>
+			<rect x="0" y="160.5" width="4.5" height="20.25" rx="2.25" ry="2.25" class="st3"/>
+		</g>
+		<g id="shape32-49" transform="translate(18.375,-153.375)">
+			<title>Sheet.32</title>
+			<path d="M0 180.75 L144 180.75" class="st4"/>
+		</g>
+		<g id="shape33-52" transform="translate(199.125,18.375) rotate(90)">
+			<title>Sheet.33</title>
+			<path d="M0 180.75 L18 180.75" class="st4"/>
+		</g>
+		<g id="shape34-55" transform="translate(343.125,18.375) rotate(90)">
+			<title>Sheet.34</title>
+			<path d="M0 180.75 L18 180.75" class="st4"/>
+		</g>
+		<g id="shape35-58" transform="translate(27.375,-135.375)">
+			<title>Sheet.35</title>
+			<desc>8</desc>
+			<rect x="0" y="162.75" width="18" height="18" class="st5"/>
+			<text x="5.96" y="175.35" class="st6">8</text>		</g>
+		<g id="shape36-61" transform="translate(63.375,-135.375)">
+			<title>Sheet.36</title>
+			<desc>4</desc>
+			<rect x="0" y="162.75" width="18" height="18" class="st5"/>
+			<text x="5.96" y="175.35" class="st6">4</text>		</g>
+		<g id="shape37-64" transform="translate(99.375,-135.375)">
+			<title>Sheet.37</title>
+			<desc>2</desc>
+			<rect x="0" y="162.75" width="18" height="18" class="st5"/>
+			<text x="5.96" y="175.35" class="st6">2</text>		</g>
+		<g id="shape38-67" transform="translate(135.375,-135.375)">
+			<title>Sheet.38</title>
+			<desc>1</desc>
+			<rect x="0" y="162.75" width="18" height="18" class="st5"/>
+			<text x="5.96" y="175.35" class="st6">1</text>		</g>
+		<g id="shape39-70" transform="translate(18.375,-153.375)">
+			<title>Sheet.39</title>
+			<desc>High</desc>
+			<rect x="0" y="162.75" width="144" height="18" class="st5"/>
+			<text x="60.91" y="175.35" class="st6">High</text>		</g>
+		<g id="shape40-73" transform="translate(162.375,-153.375)">
+			<title>Sheet.40</title>
+			<path d="M0 180.75 L144 180.75" class="st4"/>
+		</g>
+		<g id="shape41-76" transform="translate(343.125,18.375) rotate(90)">
+			<title>Sheet.41</title>
+			<path d="M0 180.75 L18 180.75" class="st4"/>
+		</g>
+		<g id="shape42-79" transform="translate(487.125,18.375) rotate(90)">
+			<title>Sheet.42</title>
+			<path d="M0 180.75 L18 180.75" class="st4"/>
+		</g>
+		<g id="shape43-82" transform="translate(171.375,-135.375)">
+			<title>Sheet.43</title>
+			<desc>8</desc>
+			<rect x="0" y="162.75" width="18" height="18" class="st5"/>
+			<text x="5.96" y="175.35" class="st6">8</text>		</g>
+		<g id="shape44-85" transform="translate(207.375,-135.375)">
+			<title>Sheet.44</title>
+			<desc>4</desc>
+			<rect x="0" y="162.75" width="18" height="18" class="st5"/>
+			<text x="5.96" y="175.35" class="st6">4</text>		</g>
+		<g id="shape45-88" transform="translate(243.375,-135.375)">
+			<title>Sheet.45</title>
+			<desc>2</desc>
+			<rect x="0" y="162.75" width="18" height="18" class="st5"/>
+			<text x="5.96" y="175.35" class="st6">2</text>		</g>
+		<g id="shape46-91" transform="translate(279.375,-135.375)">
+			<title>Sheet.46</title>
+			<desc>1</desc>
+			<rect x="0" y="162.75" width="18" height="18" class="st5"/>
+			<text x="5.96" y="175.35" class="st6">1</text>		</g>
+		<g id="shape47-94" transform="translate(162.375,-153.375)">
+			<title>Sheet.47</title>
+			<desc>Low</desc>
+			<rect x="0" y="162.75" width="144" height="18" class="st5"/>
+			<text x="62.02" y="175.35" class="st6">Low</text>		</g>
+		<g id="shape48-97" transform="translate(27.375,-99.3749)">
+			<title>Sheet.48</title>
+			<desc>7</desc>
+			<rect x="0" y="162.75" width="18" height="18" class="st5"/>
+			<text x="5.96" y="175.35" class="st6">7</text>		</g>
+		<g id="shape49-100" transform="translate(63.375,-99.3749)">
+			<title>Sheet.49</title>
+			<desc>6</desc>
+			<rect x="0" y="162.75" width="18" height="18" class="st5"/>
+			<text x="5.96" y="175.35" class="st6">6</text>		</g>
+		<g id="shape50-103" transform="translate(99.375,-99.375)">
+			<title>Sheet.50</title>
+			<desc>5</desc>
+			<rect x="0" y="162.75" width="18" height="18" class="st5"/>
+			<text x="5.96" y="175.35" class="st6">5</text>		</g>
+		<g id="shape52-106" transform="translate(135.375,-99.375)">
+			<title>Sheet.52</title>
+			<desc>4</desc>
+			<rect x="0" y="162.75" width="18" height="18" class="st5"/>
+			<text x="5.96" y="175.35" class="st6">4</text>		</g>
+		<g id="shape53-109" transform="translate(171.375,-99.375)">
+			<title>Sheet.53</title>
+			<desc>3</desc>
+			<rect x="0" y="162.75" width="18" height="18" class="st5"/>
+			<text x="5.96" y="175.35" class="st6">3</text>		</g>
+		<g id="shape54-112" transform="translate(207.375,-99.375)">
+			<title>Sheet.54</title>
+			<desc>2</desc>
+			<rect x="0" y="162.75" width="18" height="18" class="st5"/>
+			<text x="5.96" y="175.35" class="st6">2</text>		</g>
+		<g id="shape55-115" transform="translate(243.375,-99.375)">
+			<title>Sheet.55</title>
+			<desc>1</desc>
+			<rect x="0" y="162.75" width="18" height="18" class="st5"/>
+			<text x="5.96" y="175.35" class="st6">1</text>		</g>
+		<g id="shape56-118" transform="translate(279.375,-99.375)">
+			<title>Sheet.56</title>
+			<desc>0</desc>
+			<rect x="0" y="162.75" width="18" height="18" class="st5"/>
+			<text x="5.96" y="175.35" class="st6">0</text>		</g>
+		<g id="shape57-121" transform="translate(94.875,-58.875)">
+			<title>Sheet.57</title>
+			<path d="M0 180.75 L27 180.75" class="st7"/>
+		</g>
+		<g id="shape58-124" transform="translate(90.375,-58.875)">
+			<title>Sheet.58</title>
+			<desc>Auto</desc>
+			<rect x="0" y="171.75" width="36" height="9.00001" class="st5"/>
+			<text x="10.13" y="178.65" class="st8">Auto</text>		</g>
+		<g id="shape59-127" transform="translate(90.375,-49.875)">
+			<title>Sheet.59</title>
+			<desc>Menu</desc>
+			<rect x="0" y="171.75" width="36" height="9.00001" class="st5"/>
+			<text x="8.39" y="178.65" class="st8">Menu</text>		</g>
+		<g id="shape61-130" transform="translate(22.875,-58.875)">
+			<title>Sheet.61</title>
+			<path d="M0 180.75 L27 180.75" class="st7"/>
+		</g>
+		<g id="shape62-133" transform="translate(18.375,-58.875)">
+			<title>Sheet.62</title>
+			<desc>CRT</desc>
+			<rect x="0" y="171.75" width="36" height="9.00001" class="st5"/>
+			<text x="11.75" y="178.65" class="st8">CRT</text>		</g>
+		<g id="shape63-136" transform="translate(18.375,-49.875)">
+			<title>Sheet.63</title>
+			<desc>Serial</desc>
+			<rect x="0" y="171.75" width="36" height="9.00001" class="st5"/>
+			<text x="9.03" y="178.65" class="st8">Serial</text>		</g>
+		<g id="shape64-139" transform="translate(58.875,-58.875)">
+			<title>Sheet.64</title>
+			<path d="M0 180.75 L27 180.75" class="st7"/>
+		</g>
+		<g id="shape65-142" transform="translate(54.375,-58.875)">
+			<title>Sheet.65</title>
+			<desc>Sec</desc>
+			<rect x="0" y="171.75" width="36" height="9.00001" class="st5"/>
+			<text x="12.48" y="178.65" class="st8">Sec</text>		</g>
+		<g id="shape66-145" transform="translate(54.375,-49.875)">
+			<title>Sheet.66</title>
+			<desc>Pri</desc>
+			<rect x="0" y="171.75" width="36" height="9.00001" class="st5"/>
+			<text x="13.62" y="178.65" class="st8">Pri</text>		</g>
+		<g id="shape67-148" transform="translate(130.875,-58.875)">
+			<title>Sheet.67</title>
+			<path d="M0 180.75 L27 180.75" class="st7"/>
+		</g>
+		<g id="shape68-151" transform="translate(126.375,-58.875)">
+			<title>Sheet.68</title>
+			<desc>Disk</desc>
+			<rect x="0" y="171.75" width="36" height="9.00001" class="st5"/>
+			<text x="11.24" y="178.65" class="st8">Disk</text>		</g>
+		<g id="shape69-154" transform="translate(126.375,-49.875)">
+			<title>Sheet.69</title>
+			<desc>ROM</desc>
+			<rect x="0" y="171.75" width="36" height="9.00001" class="st5"/>
+			<text x="9.76" y="178.65" class="st8">ROM</text>		</g>
+		<g id="shape70-157" transform="translate(166.875,-58.875)">
+			<title>Sheet.70</title>
+			<path d="M0 180.75 L27 180.75" class="st7"/>
+		</g>
+		<g id="shape71-160" transform="translate(162.375,-58.875)">
+			<title>Sheet.71</title>
+			<desc>Floppy</desc>
+			<rect x="0" y="171.75" width="36" height="9.00001" class="st5"/>
+			<text x="7.12" y="178.65" class="st8">Floppy</text>		</g>
+		<g id="shape72-163" transform="translate(162.375,-49.875)">
+			<title>Sheet.72</title>
+			<desc>Hard</desc>
+			<rect x="0" y="171.75" width="36" height="9.00001" class="st5"/>
+			<text x="10.1" y="178.65" class="st8">Hard</text>		</g>
+		<g id="shape73-166" transform="translate(202.875,-58.875)">
+			<title>Sheet.73</title>
+			<path d="M0 180.75 L99 180.75" class="st7"/>
+		</g>
+		<g id="shape74-169" transform="translate(198.375,-49.875)">
+			<title>Sheet.74</title>
+			<desc>4</desc>
+			<rect x="0" y="171.75" width="36" height="9.00001" class="st5"/>
+			<text x="15.97" y="178.65" class="st8">4</text>		</g>
+		<g id="shape75-172" transform="translate(234.375,-49.875)">
+			<title>Sheet.75</title>
+			<desc>2</desc>
+			<rect x="0" y="171.75" width="36" height="9.00001" class="st5"/>
+			<text x="15.97" y="178.65" class="st8">2</text>		</g>
+		<g id="shape76-175" transform="translate(270.375,-49.875)">
+			<title>Sheet.76</title>
+			<desc>1</desc>
+			<rect x="0" y="171.75" width="36" height="9.00001" class="st5"/>
+			<text x="15.97" y="178.65" class="st8">1</text>		</g>
+		<g id="shape78-178" transform="translate(198.375,-58.875)">
+			<title>Sheet.78</title>
+			<desc>ROM App / Boot Slice</desc>
+			<rect x="0" y="171.75" width="108" height="9.00001" class="st5"/>
+			<text x="18.99" y="178.65" class="st8">ROM App / Boot Slice</text>		</g>
+		<g id="shape79-181" transform="translate(18.375,-0.375)">
+			<title>Sheet.79</title>
+			<desc>ROM Apps: 0=Monitor 1=BASIC 2=Forth 3=Game 4=CP/M 2.2 5=Z-Sys...</desc>
+			<rect x="0" y="171.75" width="288" height="9" class="st5"/>
+			<text x="19.9" y="178.05" class="st9">ROM Apps:   0=Monitor   1=BASIC   2=Forth   3=Game   4=CP/M 2.2   5=Z-System   6=Net Boot   7=User</text>		</g>
+		<g id="shape80-184" transform="translate(0.375,-0.375)">
+			<title>Sheet.80</title>
+			<rect x="0" y="0.750005" width="324" height="180" class="st10"/>
+		</g>
+		<g id="shape81-186" transform="translate(18.375,-72.375)">
+			<title>Sheet.81</title>
+			<path d="M0 180.75 L144 180.75" class="st4"/>
+		</g>
+		<g id="shape82-189" transform="translate(199.125,99.375) rotate(90)">
+			<title>Sheet.82</title>
+			<path d="M0 180.75 L18 180.75" class="st4"/>
+		</g>
+		<g id="shape84-192" transform="translate(18.375,-72.375)">
+			<title>Sheet.84</title>
+			<desc>Console</desc>
+			<rect x="0" y="162.75" width="72" height="18" class="st5"/>
+			<text x="16.61" y="175.35" class="st6">Console</text>		</g>
+		<g id="shape85-195" transform="translate(162.375,-72.375)">
+			<title>Sheet.85</title>
+			<path d="M0 180.75 L144 180.75" class="st4"/>
+		</g>
+		<g id="shape86-198" transform="translate(271.125,99.375) rotate(90)">
+			<title>Sheet.86</title>
+			<path d="M0 180.75 L18 180.75" class="st4"/>
+		</g>
+		<g id="shape87-201" transform="translate(487.125,99.375) rotate(90)">
+			<title>Sheet.87</title>
+			<path d="M0 180.75 L18 180.75" class="st4"/>
+		</g>
+		<g id="shape88-204" transform="translate(90.375,-72.375)">
+			<title>Sheet.88</title>
+			<desc>Boot</desc>
+			<rect x="0" y="162.75" width="216" height="18" class="st5"/>
+			<text x="96.4" y="175.35" class="st6">Boot</text>		</g>
+	</g>
+</svg>

Source/Doc/Graphics/hd512.svg

@@ -0,0 +1,236 @@
+<?xml version="1.0" encoding="UTF-8" standalone="no"?>
+<!DOCTYPE svg PUBLIC "-//W3C//DTD SVG 1.1//EN" "http://www.w3.org/Graphics/SVG/1.1/DTD/svg11.dtd">
+<!-- Generated by Microsoft Visio, SVG Export hd512.svg Page-1 -->
+<svg xmlns="http://www.w3.org/2000/svg" xmlns:xlink="http://www.w3.org/1999/xlink" xmlns:ev="http://www.w3.org/2001/xml-events"
+		width="6.51389in" height="3.90694in" viewBox="0 0 469 281.3" xml:space="preserve" color-interpolation-filters="sRGB"
+		class="st16">
+	<style type="text/css">
+	<![CDATA[
+		.st1 {fill:#ffffff;stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:1}
+		.st2 {fill:#000000;font-family:Calibri;font-size:1.5em}
+		.st3 {fill:#ffffff;stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.24}
+		.st4 {fill:#000000;font-family:Calibri;font-size:0.666664em}
+		.st5 {fill:none;stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:1}
+		.st6 {fill:#d8d8d8;stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:1}
+		.st7 {fill:none;stroke:none;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.75}
+		.st8 {marker-start:url(#mrkr4-40);stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.24}
+		.st9 {fill:#000000;fill-opacity:1;stroke:#000000;stroke-opacity:1;stroke-width:0.08695652173913}
+		.st10 {fill:#000000;font-family:Calibri;font-size:0.499992em}
+		.st11 {marker-end:url(#mrkr4-58);stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.24}
+		.st12 {stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.25}
+		.st13 {marker-end:url(#mrkr9-69);marker-start:url(#mrkr4-40);stroke:#000000;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.24}
+		.st14 {marker-end:url(#mrkr4-114);stroke:#000000;stroke-dasharray:1.75,1.25;stroke-linecap:round;stroke-linejoin:round;stroke-width:0.25}
+		.st15 {fill:#000000;fill-opacity:1;stroke:#000000;stroke-opacity:1;stroke-width:0.090252707581227}
+		.st16 {fill:none;fill-rule:evenodd;font-size:12px;overflow:visible;stroke-linecap:square;stroke-miterlimit:3}
+	]]>
+	</style>
+
+	<defs id="Markers">
+		<g id="lend4">
+			<path d="M 2 1 L 0 0 L 2 -1 L 2 1 " style="stroke:none"/>
+		</g>
+		<marker id="mrkr4-40" class="st9" refX="21.5" orient="auto" markerUnits="strokeWidth" overflow="visible">
+			<use xlink:href="#lend4" transform="scale(11.5) "/>
+		</marker>
+		<marker id="mrkr4-58" class="st9" refX="-23" orient="auto" markerUnits="strokeWidth" overflow="visible">
+			<use xlink:href="#lend4" transform="scale(-11.5,-11.5) "/>
+		</marker>
+		<g id="lend9">
+			<path d="M 1 -1 L -1 1 " style="stroke-linecap:round;stroke-linejoin:round;fill:none"/>
+		</g>
+		<marker id="mrkr9-69" class="st9" orient="auto" markerUnits="strokeWidth" overflow="visible">
+			<use xlink:href="#lend9" transform="scale(-11.5,-11.5) "/>
+		</marker>
+		<marker id="mrkr4-114" class="st15" refX="-22.16" orient="auto" markerUnits="strokeWidth" overflow="visible">
+			<use xlink:href="#lend4" transform="scale(-11.08,-11.08) "/>
+		</marker>
+	</defs>
+	<g>
+		<title>Page-1</title>
+		<g id="shape69-1" transform="translate(0.5,-252)">
+			<title>Sheet.69</title>
+			<desc>RomWBW Hard Disk Anatomy (Classic / hd512)</desc>
+			<rect x="0" y="252.5" width="468" height="28.8" class="st1"/>
+			<text x="61.63" y="272.3" class="st2">RomWBW Hard Disk Anatomy (Classic / hd512)</text>		</g>
+		<g id="shape259-4" transform="translate(50.9,-151.2)">
+			<title>Sheet.259</title>
+			<desc>0</desc>
+			<rect x="0" y="266.9" width="14.4" height="14.4" class="st3"/>
+			<text x="5.17" y="276.5" class="st4">0</text>		</g>
+		<g id="shape260-7" transform="translate(65.3,-151.2)">
+			<title>Sheet.260</title>
+			<desc>1</desc>
+			<rect x="0" y="266.9" width="14.4" height="14.4" class="st3"/>
+			<text x="5.17" y="276.5" class="st4">1</text>		</g>
+		<g id="shape261-10" transform="translate(79.7,-151.2)">
+			<title>Sheet.261</title>
+			<desc>2</desc>
+			<rect x="0" y="266.9" width="14.4" height="14.4" class="st3"/>
+			<text x="5.17" y="276.5" class="st4">2</text>		</g>
+		<g id="shape262-13" transform="translate(94.1,-151.2)">
+			<title>Sheet.262</title>
+			<desc>3</desc>
+			<rect x="0" y="266.9" width="14.4" height="14.4" class="st3"/>
+			<text x="5.17" y="276.5" class="st4">3</text>		</g>
+		<g id="shape263-16" transform="translate(108.5,-151.2)">
+			<title>Sheet.263</title>
+			<desc>. . .</desc>
+			<rect x="0" y="266.9" width="72" height="14.4" class="st3"/>
+			<text x="27.54" y="276.5" class="st4">.   .   .</text>		</g>
+		<g id="shape264-19" transform="translate(180.5,-151.2)">
+			<title>Sheet.264</title>
+			<desc>N</desc>
+			<rect x="0" y="266.9" width="14.4" height="14.4" class="st3"/>
+			<text x="4.62" y="276.5" class="st4">N</text>		</g>
+		<g id="shape265-22" transform="translate(50.9,-151.2)">
+			<title>Sheet.265</title>
+			<rect x="0" y="266.9" width="144" height="14.4" class="st5"/>
+		</g>
+		<g id="shape266-24" transform="translate(50.9,-122.4)">
+			<title>Sheet.266</title>
+			<desc>RomWBW Hard Disk (IDE/ATA/ATAPI/CF/SD/USB)</desc>
+			<rect x="0" y="266.9" width="360" height="14.4" class="st6"/>
+			<text x="99.2" y="276.5" class="st4">RomWBW Hard Disk (IDE/ATA/ATAPI/CF/SD/USB)</text>		</g>
+		<g id="shape267-27" transform="translate(230.9,-136.8)">
+			<title>Sheet.267</title>
+			<desc>FAT Partition</desc>
+			<rect x="0" y="266.9" width="165.6" height="14.4" class="st1"/>
+			<text x="61.69" y="276.5" class="st4">FAT Partition</text>		</g>
+		<g id="shape268-30" transform="translate(101.3,-43.2)">
+			<title>Sheet.268</title>
+			<desc>Sector 0</desc>
+			<rect x="0" y="266.9" width="72" height="14.4" class="st7"/>
+			<text x="22.71" y="276.5" class="st4">Sector 0</text>		</g>
+		<g id="shape269-33" transform="translate(158.9,-57.6)">
+			<title>Sheet.269</title>
+			<rect x="0" y="266.9" width="14.4" height="14.4" class="st3"/>
+		</g>
+		<g id="shape270-35" transform="translate(50.9,-64.8)">
+			<title>Sheet.270</title>
+			<path d="M0 228.86 L0 229.22 L0 276.8 A4.5 4.5 -180 0 0 4.5 281.3 L46.08 281.3" class="st8"/>
+		</g>
+		<g id="shape271-41" transform="translate(209.3,-43.2)">
+			<title>Sheet.271</title>
+			<desc>Type 06</desc>
+			<rect x="0" y="274.1" width="43.2" height="7.2" class="st3"/>
+			<text x="11.99" y="279.5" class="st10">Type 06</text>		</g>
+		<g id="shape272-44" transform="translate(209.3,-36)">
+			<title>Sheet.272</title>
+			<rect x="0" y="274.1" width="43.2" height="7.2" class="st3"/>
+		</g>
+		<g id="shape273-46" transform="translate(209.3,-28.8)">
+			<title>Sheet.273</title>
+			<rect x="0" y="274.1" width="43.2" height="7.2" class="st3"/>
+		</g>
+		<g id="shape274-48" transform="translate(209.3,-21.6)">
+			<title>Sheet.274</title>
+			<rect x="0" y="274.1" width="43.2" height="7.2" class="st3"/>
+		</g>
+		<g id="shape275-50" transform="translate(202.1,-7.19997)">
+			<title>Sheet.275</title>
+			<desc>Partition Table</desc>
+			<rect x="0" y="266.9" width="57.6" height="14.4" class="st7"/>
+			<text x="4.92" y="276.5" class="st4">Partition Table</text>		</g>
+		<g id="shape276-53" transform="translate(339.4,65.2999) rotate(90)">
+			<title>Sheet.276</title>
+			<path d="M0 98.42 L0 258.8 A22.5 22.5 -180 0 0 22.5 281.3 L44.88 281.3" class="st11"/>
+		</g>
+		<g id="shape277-59" transform="translate(-71.9999,259.7) rotate(-90)">
+			<title>Bracket.132</title>
+			<path d="M0 281.3 A5.43323 5.43323 0 0 1 4.8 276.5 L9.6 276.5 A5.43323 5.43323 -180 0 0 14.4 271.7 A5.43323 5.43323 -180
+						 0 0 19.2 276.5 L24 276.5 A5.43323 5.43323 0 0 1 28.8 281.3" class="st12"/>
+		</g>
+		<g id="shape278-62" transform="translate(252.5,-180)">
+			<title>Sheet.278</title>
+			<path d="M0 272.06 L0 272.42 L0 274.1 A7.19998 7.19998 -180 0 0 7.2 281.3 L28.8 281.3" class="st13"/>
+		</g>
+		<g id="shape279-70" transform="translate(284.9,-172.8)">
+			<title>Sheet.279</title>
+			<desc>CP/M System Area (128 KB)</desc>
+			<rect x="0" y="266.9" width="111.6" height="14.4" class="st7"/>
+			<text x="1" y="276.5" class="st4">CP/M System Area (128 KB)</text>		</g>
+		<g id="shape280-73" transform="translate(353.8,65.2999) rotate(90)">
+			<title>Sheet.280</title>
+			<path d="M0 112.82 L0 258.8 A22.5 22.5 -180 0 0 22.5 281.3 L44.88 281.3" class="st11"/>
+		</g>
+		<g id="shape281-78" transform="translate(368.2,65.2999) rotate(90)">
+			<title>Sheet.281</title>
+			<path d="M0 127.22 L0 258.8 A22.5 22.5 -180 0 0 22.5 281.3 L44.88 281.3" class="st11"/>
+		</g>
+		<g id="shape282-83" transform="translate(382.6,65.2999) rotate(90)">
+			<title>Sheet.282</title>
+			<path d="M0 141.62 L0 258.8 A22.5 22.5 -180 0 0 22.5 281.3 L44.88 281.3" class="st11"/>
+		</g>
+		<g id="shape283-88" transform="translate(469,65.2999) rotate(90)">
+			<title>Sheet.283</title>
+			<path d="M0 228.02 L0 258.8 A22.5 22.5 -180 0 0 22.5 281.3 L44.88 281.3" class="st11"/>
+		</g>
+		<g id="shape284-93" transform="translate(158.9,-68.3999)">
+			<title>Sheet.284</title>
+			<rect x="0" y="277.7" width="14.4" height="3.6" class="st3"/>
+		</g>
+		<g id="shape285-95" transform="translate(158.9,-64.7999)">
+			<title>Sheet.285</title>
+			<rect x="0" y="277.7" width="14.4" height="3.6" class="st3"/>
+		</g>
+		<g id="shape286-97" transform="translate(158.9,-61.1999)">
+			<title>Sheet.286</title>
+			<rect x="0" y="277.7" width="14.4" height="3.6" class="st3"/>
+		</g>
+		<g id="shape287-99" transform="translate(158.9,-57.5999)">
+			<title>Sheet.287</title>
+			<rect x="0" y="277.7" width="14.4" height="3.6" class="st3"/>
+		</g>
+		<g id="shape288-101" transform="translate(166.1,-57.6)">
+			<title>Stack pointer.179</title>
+			<path d="M33.6 302.9 L5.4 302.9 A5.39999 5.39999 0 0 1 0 297.5 L0 292.1 L0 286.82" class="st11"/>
+		</g>
+		<g id="shape289-106" transform="translate(50.9,-136.8)">
+			<title>Sheet.289</title>
+			<desc>RomWBW Data (8,320 KB * N)</desc>
+			<rect x="0" y="266.9" width="144" height="14.4" class="st1"/>
+			<text x="22.71" y="276.5" class="st4">RomWBW Data (8,320 KB * N)</text>		</g>
+		<g id="shape293-109" transform="translate(252.5,-46.8)">
+			<title>Dynamic connector.207</title>
+			<path d="M0 281.3 L17.1 281.3 A4.5 4.5 -180 0 0 21.6 276.8 L21.6 231.8 A4.5 4.5 -180 0 0 17.1 227.3 L-17.1 227.3 A4.5
+						 4.5 0 0 1 -21.6 222.8 L-21.6 211.24" class="st14"/>
+		</g>
+		<g id="shape294-115" transform="translate(101.3,-57.6)">
+			<title>Sheet.294</title>
+			<desc>MBR</desc>
+			<rect x="0" y="266.9" width="72" height="14.4" class="st5"/>
+			<text x="28.23" y="276.5" class="st4">MBR</text>		</g>
+		<g id="shape295-118" transform="translate(209.156,-21.5999)">
+			<title>Sheet.295</title>
+			<rect x="0" y="252.5" width="43.344" height="28.8" class="st5"/>
+		</g>
+		<g id="shape296-120" transform="translate(245.3,-208.8)">
+			<title>Sheet.296</title>
+			<desc>Slice (8,320 KB)</desc>
+			<rect x="0" y="266.9" width="151.2" height="14.4" class="st5"/>
+			<text x="50.65" y="276.5" class="st4">Slice (8,320 KB)</text>		</g>
+		<g id="shape298-123" transform="translate(245.3,-194.4)">
+			<title>Sheet.298</title>
+			<rect x="0" y="266.9" width="14.4" height="14.4" class="st3"/>
+		</g>
+		<g id="shape299-125" transform="translate(245.3,-194.4)">
+			<title>Sheet.299</title>
+			<desc>CP/M File System (8 MB)</desc>
+			<rect x="0" y="266.9" width="151.2" height="14.4" class="st7"/>
+			<text x="35.37" y="276.5" class="st4">CP/M File System (8 MB)</text>		</g>
+		<g id="shape300-128" transform="translate(245.3,-194.4)">
+			<title>Sheet.300</title>
+			<rect x="0" y="266.9" width="151.2" height="14.4" class="st5"/>
+		</g>
+		<g id="shape301-130" transform="translate(-180,223.7) rotate(-90)">
+			<title>Bracket.301</title>
+			<path d="M-0 281.3 A2.41217 2.41217 0 0 1 2.13 279.17 L5.07 279.17 A2.41217 2.41217 -180 0 0 7.2 277.04 A2.41217 2.41217
+						 -180 0 0 9.33 279.17 L12.27 279.17 A2.41217 2.41217 0 0 1 14.4 281.3" class="st12"/>
+		</g>
+		<g id="shape302-133" transform="translate(-35.9999,72.5) rotate(-90)">
+			<title>Bracket.302</title>
+			<path d="M-0 281.3 A2.41217 2.41217 0 0 1 2.13 279.17 L5.07 279.17 A2.41217 2.41217 -180 0 0 7.2 277.04 A2.41217 2.41217
+						 -180 0 0 9.33 279.17 L12.27 279.17 A2.41217 2.41217 0 0 1 14.4 281.3" class="st12"/>
+		</g>
+	</g>
+</svg>

Source/Doc/Makefile

@@ -1,13 +1,19 @@
 #
-# NOTE: gpp, Pandoc, and Latex (MiKTeX or TexLive) must be installed
+# NOTE: gpp, Pandoc, LuaLatex (MiKTeX or TexLive), and Roboto Font must be installed
 # and available on commandline for this build to work!!!
-# Typically "sudo apt install gpp pandoc texlive-latex-extra texlive-luatex texlive-fonts-extra fonts-roboto"
 #
-OBJECTS = ReadMe.gfm ReadMe.txt UserGuide.pdf SystemGuide.pdf Applications.pdf ROM_Applications.pdf Catalog.pdf Errata.pdf
+# On MacOS:
+# brew install gpp pandoc texlive
+# brew install --cask font-roboto
+#
+# On Ubuntu Linux:
+# apt install gpp pandoc texlive texlive-luatex texlive-fonts-extra
+#
+OBJECTS = ReadMe.gfm ReadMe.txt UserGuide.pdf SystemGuide.pdf Applications.pdf Catalog.pdf Errata.pdf
 # DEST = ../../Doc
 TOOLS = ../../Tools
 OTHERS = *.tmp
-
+
 include $(TOOLS)/Makefile.inc
 
 all :: deploy
@@ -36,6 +42,5 @@ deploy :
 	cp UserGuide.pdf         "../../Doc/RomWBW User Guide.pdf"
 	cp SystemGuide.pdf       "../../Doc/RomWBW System Guide.pdf"
 	cp Applications.pdf      "../../Doc/RomWBW Applications.pdf"
-	cp ROM_Applications.pdf  "../../Doc/RomWBW ROM Applications.pdf"
 	cp Catalog.pdf           "../../Doc/RomWBW Disk Catalog.pdf"
-	cp Errata.pdf             "../../Doc/RomWBW Errata.pdf"
+	cp Errata.pdf            "../../Doc/RomWBW Errata.pdf"

Source/Doc/ROM_Applications.md

@@ -1,635 +0,0 @@
-$define{doc_title}{ROM Applications}$
-$define{doc_author}{Phillip Summers}$
-$define{doc_authmail}{}$
-$include{"Book.h"}$
-
-# Summary
-
-RomWBW includes a small selection of built in utilities and
-programming languages.
-
-`\clearpage`{=latex}
-
-# RomWBW Monitor
-
-The Monitor program is a low level utility that can be used 
-for testing and programming. It allows programs to be entered,
-memory to be examined, and input/output devices to be read or
-written to.
-
-It's key advantage is that is available at boot up. 
-
-Its key disadvantages are that code cannot be entered in assembly 
-language and there is no ability to save to memory devices.
-
-The available memory area for programming is `0200-EDFFh`.
-The following areas are reserved:
-
-Memory Area | Function
-------------|-----------------------------------
-`0000-00FFh`| Jump and restart (RST) vectors
-`0100-01FFh`| HBIOS configuration block
-`EE00-FDFFh`| MONITOR
-`FE00-FFFFh`| HBIOS proxy
-
-Commands can be entered at the command prompt `>` 
-Automatic case conversion takes place on command entry and all 
-arguments are expected to be in hex format.
-
-The current memory bank in low memory is displayed before the prompt i.e.:
-
-`8E>`
-
-The Monitor allows access to all memory locations but ROM and
-Flash memory cannot be written to. Memory outside the normal
-address range can be accessed using the B command. The first
-256 bytes `0000-01FF` is critical for the HBIOS operation.
-Changing banks may make this information inaccessible.
-
-Refer to the RomWBW Architecture manual for details memory banking.
-
-A quick guide to using the Monitor program follows:
-
-## ? - Displays a summary of available commands.
-
-```
-Monitor Commands (all values in hex):
-B                    - Boot system
-D xxxx [yyyy]        - Dump memory from xxxx to yyyy
-F xxxx yyyy zz       - Fill memory from xxxx to yyyy with zz
-H                    - Halt system
-I xxxx               - Input from port xxxx
-K                    - Keyboard echo
-L                    - Load Intel hex data
-M xxxx yyyy zzzz     - Move memory block xxxx-yyyy to zzzz
-O xxxx yy            - Output value yy to port xxxx
-P xxxx               - Program RAM at address xxxx
-R xxxx [[yy] [zzzz]] - Run code at address xxxx
-                       Pass yy and zzzz to register A and BC
-T xxxx	             - X-modem transfer to memory location xxxx
-S xx                 - Set bank to xx
-X                    - Exit monitor
-```
-
-## Cold Boot
-
-B - Performs a cold boot of the ROMWBW system. A complete
-re-initialization of the system is performed and the system
-returns to the Boot Loader prompt.
-
-## Dump Memory
-
-D xxxx [yyyy] - Dump memory from hex location xxxx to yyyy
-on the screen as lines of 16 hexadecimal bytes with their
-ASCII equivalents (if within a set range, else a '.' is
-printed). If the end address is omitted then 256 bytes is
-displayed. 
-
-A good tool to see where code is located, check
-for version id, obtain details for chip configurations and
-execution paths.
-
-Examples: `D 100 1FF`
-
-```
-0100: 10 0B 01 5A 33 45 4E 56 01 00 00 2A 06 00 F9 11  ...Z3ENV...*..ù.
-0110: DE 38 37 ED 52 4D 44 0B 6B 62 13 36 00 ED B0 21  Þ87íRMD.kb.6.í°!
-0120: 7D 32 E5 21 80 00 4E 23 06 00 09 36 00 21 81 00  }2å!..N#...6.!..
-0130: E5 CD 6C 1F C1 C1 E5 2A C9 8C E5 CD 45 05 E5 CD  åÍl.ÁÁå*É.åÍE.åÍ
-0140: 59 1F C3 00 00 C3 AE 01 C3 51 04 C3 4C 02 C3 57  Y.Ã..î.ÃQ.ÃL.ÃW
-0150: 02 C3 64 02 C3 75 02 C3 88 02 C3 B2 03 C3 0D 04  .Ãd.Ãu.Ã..ò.Ã..
-0160: C3 19 04 C3 22 04 C3 2A 04 C3 35 04 C3 40 04 C3  Ã..Ã".Ã*.Ã5.Ã@.Ã
-0170: 48 04 C3 50 04 C3 50 04 C3 50 04 C3 8F 02 C3 93  H.ÃP.ÃP.ÃP.Ã..Ã.
-0180: 02 C3 94 02 C3 95 02 C3 85 04 C3 C7 04 C3 D1 01  .Ã..Ã..Ã..ÃÇ.ÃÑ.
-0190: C3 48 02 C3 E7 04 C3 56 03 C3 D0 01 C3 D0 01 C3  ÃH.Ãç.ÃV.ÃÐ.ÃÐ.Ã
-01A0: D0 01 C3 D0 01 C3 D0 01 C3 D0 01 01 02 01 CD 6B  Ð.ÃÐ.ÃÐ.ÃÐ....Ík
-01B0: 04 54 68 69 73 20 66 75 6E 63 74 69 6F 6E 20 6E  .This function n
-01C0: 6F 74 20 73 75 70 70 6F 72 74 65 64 2E 0D 0A 00  ot supported....
-01D0: C9 3E FF 32 3C 00 3A 5D 00 FE 20 28 14 D6 30 32  É>ÿ2<.:].þ (.Ö02
-01E0: AB 01 32 AD 01 3A 5E 00 FE 20 28 05 D6 30 32 AC  «.2­.:^.þ (.Ö02¬
-01F0: 01 C5 01 F0 F8 CF E5 26 00 0E 0A CD 39 02 7D 3C  .Å.ðøÏå&...Í9.}<
-```
-
-## Fill Memory
-
-F xxxx yyyy zz - Fill memory from hex xxxx to yyyy with
-a single value of zz over the full range. The Dump command
-can be used to confirm that the fill completed as expected. A
-good way to zero out memory areas before writing machine data
-for debug purposes.
-
-## Halt System
-
-H - Halt system. A Z80 HALT instruction is executed. The
-system remains in the halt state until the system is
-physically rebooted. Interrupts will not restart the
-system. On systems that support a HALT status LED, the
-LED will be illuminated.
-
-## Input from port
-
-I xxxx - Input data from port xxxx and display to the screen.
-This command is used to read values from hardware I/O ports
-and display the contents in hexadecimal. 
-
-## Keyboard Echo
-
-K - Echo any key-presses from the terminal. Press 'ESC' key
-to quit. This facility provides that any key stroke sent to
-the computer will be echoed back to the terminal. File down
-loads will be echoed as well while this facility is ‘on’.
-
-## Load Hex format file into memory
-
-L - Load a Intel Hex format file via the terminal program.
-The load address is defined in the hex file of the
-assembled code.
-
-The terminal emulator program should be configured to
-give a delay at the end of each line to allow the monitor
-enough time to parse the line and move the data to memory.
-
-Keep in mind that this will be a transient unless the
-system support battery backed memory. Saving to memory drive 
-is not supported.
-
-## Move memory
-
-M xxxx yyyy zzzz - Move hex memory block xxxx to yyyy to
-memory starting at hex location zzzz. Care should be taken
-to insure that there is enough memory at the destination so
-that code does not get over-written or memory wrapped around.
-
-## Output to port
-
-O xxxx yy - Output data byte xx to port xxxx. This command is
-used to send hexadecimal values to hardware I/O ports to
-verify their operation and is the companion to the I operation.
-Use clip leaded LEDs to confirm the data written.
-
-## Program memory location
-
-P xxxx - Program memory location xxxx. This routine will
-allow you to program a hexadecimal value 'into memory starting
-at location xxxx. Press 'Enter' on a blank line to
-return to the Monitor prompt.
-
-The limitation around programming memory is that it must be 
-entered in hexadecimal. An alternative is to use the L command
-to load a program that has been assembled to a hex file on the
-remote computer.
-
-An excellent online resource for looking up opcodes for entry
-can be found here: [https://clrhome.org/table](https://clrhome.org/table)
-
-## Run program
-
-R xxxx [[yy] [zzzz]] - Run program at location xxxx. If optional
-arguments yy and zzzz are entered they are loaded into the
-A and BC register respectively. The return address of the
-Monitor is saved on the stack so the program can return
-to the monitor. On return to the monitor, the contents of
-the A, HL, DE and BC registers are displayed.
-
-## Set bank
-
-S xx - Change the bank in memory to xx. Memory addresses
-0000-7FFF (i.e. bottom 32k) are affected. Because the
-interrupt vectors are stored in the bottom page of this
-range, this function is disable when interrupt mode 1 is
-being used (IM1). Interrupt mode 2 is not affected as the
-associated jump vectors are stored in high memory. 
-
-Changing the bank also impacts the restart vectors (RST),
-so executing code that call the HBIOS using the RST 08
-assembly code will not work.
-
-The monitor stack resides in high memory and is not affected
-but any code that changes the stack to low memory will be
-affected.
-
-### Bank codes and descriptions
-
-TYPE | DESCRIPTION        |BANK| DETAILS
------|--------------------|----|---------------------
-RAM  | COMMON BANK        | 9F | 1024K RAM SYSTEM
-RAM  | USER BANK          | 9E | 1024K RAM SYSTEM
-RAM  | BIOS BANK          | 9D | 1024K RAM SYSTEM
-RAM  | AUX BANK           | 9C | 1024K RAM SYSTEM
-RAM  | OS BUFFERS END     | 9B | 1024K RAM SYSTEM
-RAM  | OS BUFFERS START   | 98 | 1024K RAM SYSTEM
-RAM  | RAM DRIVE END	  | 97 | 1024K RAM SYSTEM
-RAM  | COMMON BANK        | 8F | 512K RAM SYSTEM
-RAM  | USER BANK          | 8E | 512K RAM SYSTEM
-RAM  | BIOS BANK          | 8D | 512K RAM SYSTEM
-RAM  | AUX BANK           | 8C | 512K RAM SYSTEM
-RAM  | OS BUFFERS         | 8B | 512K RAM SYSTEM
-RAM  | OS BUFFERS         | 8A | 512K RAM SYSTEM
-RAM  | OS BUFFERS         | 89 | 512K RAM SYSTEM
-RAM  | OS BUFFERS         | 88 | 512K RAM SYSTEM
-RAM  | RAM DRIVE END	  | 87 | 512K RAM SYSTEM
-RAM  | RAM DRIVE START    | 80 |
-ROM  | BOOT BANK          | 00 | COLD START & HBIOS
-ROM  | LOADER & IMAGES    | 01 | MONITOR, FORTH
-ROM  | ROM IMAGES CONTD.  | 02 | BASIC, ETC
-ROM  | FAT FILESYSTEM     | 03 | UNA ONLY, ELSE UNUSED
-ROM  | ROM DRIVE START    | 04 |
-ROM  | ROM DRIVE END      | 0F | 512K ROM SYSTEM
-ROM  | ROM DRIVE END      | 1F | 1024K ROM SYSTEM
-
-## X-modem transfer
-
-T xxxx - Receive an X-modem file transfer and load it into
-memory starting at location xxxx. 
-
-128 byte blocks and checksum mode is the only supported 
-protocol.
-
-If the monitor is assembled with the DSKY functionality,
-this feature will be exclude due to space limitations.
-
-
-## NOTES:
-
-The RTC utility on the CP/M ROM disk provides facilities
-to manipulate the Real Time Clock non-volatile Memory. 
-Use the C or Z option from the Boot Loader to load CP/M 
-and then run RTC to see the options list.
-
-# FORTH
-
-CamelForth is the version of Forth included as part of the boot
-ROM in ROMWBW. It has been converted from the Z80 CP/M version
-published here [www.camelforth.com/page.php?5](www.camelforth.com/page.php?5). The author is Brad
-Rodriguez who is a prolific Forth enthusiast, whose work can be
-found here: [www.bradrodriguez/papers/index.html](www.bradrodriguez/papers/index.html)
-
-For those are who are not familiar with Forth, I recommend the
-wikipedia article [en.wikipedia.org/wiki/Forth_(programming_language](en.wikipedia.org/wiki/Forth_(programming_language))
-and the Forth Interest Group website [www.forth.org](www.forth.org)
-
-## Important things to know
-
-Forth is case sensitive.
-
-To exit back to the boot loader type ***bye***
-
-To get a list of available words type ***WORDS***
-
-To reset Forth to its initial state type ***COLD***
-
-Most of the code you find on the internet will not run unless modified or additional Forth
-words are added to the dictionary.
-
-This implementation does not support loading or saving of programs. All programs
-need to be typed in. Additionally, screen editing and code blocks are not supported.
-
-## Structure of Forth source files
-
-File          | Description
---------------|-----------------------------
-camel80.azm   | Code Primitives
- camel80d.azm | CPU Dependencies
- camel80h.azm | High Level words
- camel80r.azm | ROMWBW additions
-glosshi.txt   | Glossary of high level words
-glosslo.txt   | Glossary of low level words
-glossr.txt    | Glossary of ROMWBW additions
-
-## ROMWBW Additions
-
-Extensions and changes to this implementation compared to the original distribution are:
-
-The source code has been converted from Z80mr assembler to Hector Peraza's zsm.
-
-An additional file camel80r.azm has been added for including additional words to 
-the dictionary at build time. However, as currently configured there is very little space
-allocated for addition words. Exceeding the allocated ROM space will generate an error
-message when building.
-
-James Bowman's double precision words have been added from his RC2014 version:
-[https://github.com/jamesbowman/camelforth-z80](https://github.com/jamesbowman/camelforth-z80)
-
-Word    | Syntax                     | Description
---------|----------------------------|---------------------------------
-D+	| d1 d2 -- d1+d2             | Add double numbers
-2>R	| d --                       | 2 to R
-2R>	| d --                       | fetch 2 from R
-M*/	| d1 n2 u3 --  d=(d1*n2)/u3  | double precision mult. div
-SVC	| hl de bc n -- hl de bc af  | Execute a ROMWBW function
-P!	| n p --                     | Write a byte to a I/O port
-P@      | p -- n                     | Read a byte from and I/O port
-
-# BASIC
-
-For those who are not familiar with BASIC, it stands for Beginners All purpose Symbolic
-Instruction Code. 
-
-ROMWBW contains two versions of ROM BASIC, a full implementation and a "tiny" BASIC.
-
-The full implementation is a version of Microsoft BASIC from the NASCOM Computer.
-
-A comprehensive instruction manual is available in the Doc\\Contrib directory.
-
-## ROMWBW specific features
-
-- Sound
-- Graphics
-- Terminal Support
-
-## ROMWBW unsupported features
-
-- This ROM-hosted implementation does not support cassette or disk
-  access for loading and saving programs.
-
-# TastyBASIC
-
-TastyBASIC offers a minimal implementation of BASIC that is only 2304 bytes in size. 
-It originates from Li-Chen Wang's Palo Alto Tiny BASIC from around 1976. It's small size suited the tiny memory capacities of the time. This implementation is by Dimitri Theulings and his
-original source can be found here [https://github.com/dimitrit/tastybasic](https://github.com/dimitrit/tastybasic)
-
-## Features / Limitations
-
-- This ROM-hosted implementation does not support disk access for
-  loading and saving programs.
-- Integer arithmetic, numbers -32767 to 32767
-- Singles letter variables A-Z
-- 1-dimensional array support
-- Strings are not supported
-
-## Direct Commands
-
-- `LIST`,`RUN`, `NEW`, `CLEAR`, `BYE`
-
-## Statements
-
-- `LET`, `IF`, `GOTO`, `GOSUB RETURN`, `REM`, `FOR TO NEXT STEP`, `INPUT`, `PRINT`, `POKE`, `END`
-
-## Functions
-
-- `PEEK`, `RND`, `ABS`, `USR`, `SIZE`
-
-## Operators
-
-- `>=`, `#`, `>`, `=`, `<=`, `<`
-
-- Operator precedence is supported.
-
-Type ***BYE*** to return to the monitor.
-
-# Play a Game
-
-## 2048
-
-2048 is a puzzle game that can be both mindless and challenging. It
-appears deceptively simple but failure can creep up on you suddenly.
-
-It requires an ANSI/VT-100 compatible colour terminal to play.
-
-2048 is like a sliding puzzle game except the puzzle tiles are 
-numbers instead of pictures. Instead of moving a single tile all 
-tiles are moved simultaneously in the same direction. Where two 
-tiles of the same number collide, they are reduced to one tile with
-the combined value. After every move a new tile is added with
-a starting value of 2. 
-
-The goal is to create a tile of 2048 before all tile locations are
-occupied. Reaching the highest points score, which is the sum of all
-the tiles is a secondary goal. The game will automatically end when 
-there are no more possible moves.
-
-Play consists of entering a direction to move. Directions can be entered
-using any of three different keyboard direction sets.
-
-```
-Direction | Keys
-----------|----------
-Up        | w ^E 8
-Down      | s ^X 2
-Left      | a ^S 4
-Right     | d ^D 6
-```
-The puzzle board is a 4x4 grid. At start, the grid will be populated
-with two 2 tiles. An example game sequence is shown below with new
-tiles to the game shown in brackets.
-
-```
-Start             Move 1 - Up       Move 2 - Left     Move 3 - Left
-+---+---+---+---+ +---+---+---+---+ +---+---+---+---+ +---+---+---+---+
-|   |   |   |(2)| |   |   |   | 4 | | 4 |   |   |   | | 4 |   |   |   |
-+---+---+---+---+ +---+---+---+---+ +---+---+---+---+ +---+---+---+---+
-|   |   |   |   | |   |   |   |   | |   |   |   |(4)| | 4 |   |   |   |
-+---+---+---+---+ +---+---+---+---+ +---+---+---+---+ +---+---+---+---+
-|   |   |   |(2)| |   |   |   |   | |   |   |   |   | |   |   |   |   |
-+---+---+---+---+ +---+---+---+---+ +---+---+---+---+ +---+---+---+---+
-|   |   |   |   | |   |   |(2)|   | | 2 |   |   |   | | 2 |   |(2)|   |
-+---+---+---+---+ +---+---+---+---+ +---+---+---+---+ +---+---+---+---+
-
-Move 4 - Left     Move 5 - Up       Move 6 - Right    Move 7 - Up
-+---+---+---+---+ +---+---+---+---+ +---+---+---+---+ +---+---+---+---+
-| 4 |   |   |   | | 8 |   |   | 4 | |   |   | 8 | 4 | |   |   | 8 | 8 |
-+---+---+---+---+ +---+---+---+---+ +---+---+---+---+ +---+---+---+---+
-| 4 |   |   |(4)| | 4 |   |   |   | |   |   |   | 4 | |   |   |   | 2 |
-+---+---+---+---+ +---+---+---+---+ +---+---+---+---+ +---+---+---+---+
-|   |   |   |   | |   |   |   |   | |   |   |   |   | |   |   |   |   |
-+---+---+---+---+ +---+---+---+---+ +---+---+---+---+ +---+---+---+---+
-| 4 |   |   |   | |(2)|   |   |   | |(2)|   |   | 2 | |(2)|   |   |   |
-+---+---+---+---+ +---+---+---+---+ +---+---+---+---+ +---+---+---+---+
-```
-This is how I lost this game:
-```
-+---+---+---+---+
-| 4 | 2 | 16| 4 |
-+---+---+---+---+
-| 32| 64| 8 | 2 |
-+---+---+---+---+
-| 4 | 8 |128| 32|
-+---+---+---+---+
-|(2)| 16| 8 | 4 |
-+---+---+---+---+
-```
-Press Q at any time to bring up the option to Quit or Restart the game.
-
-# Network Boot
-
-# Xmodem Flash Updater
-
-The ROMWBW Xmodem flash updater provides the capability to update ROMWBW from the boot loader using  an x-modem file transfer. It offers similar capabilities to Will Sowerbutts FLASH4 utility except that the flashing process occurs during the file transfer. 
-
-These are the key differences between the two methods are:
-
-Xmodem Flash Updater            | FLASH4
---------------------------------|-----------------
-Available from the boot loader   | Well proven and tested
-Xmodem transfer is integrated    | Wider range of supported chips and hardware
-Integrated checksum utilities    | Wider range of supported platforms
-Capability to copy a ROM image   | Only reprograms sectors that have changed
-More convenient one step process | Ability save and verify ROM images
-No intermediate storage required | Progress display while flashing
-.                                | Displays chip identification information
-.                                | Faster file transfer
-                                 
-The major disadvantages of the Updater is that it is new and relatively untested. There is the risk that a failed transfer will result in a partially flashed and unbootable ROM. There are some limitations on serial transfer speeds.
- 
-The updater utility was initially intended to support the Retrobrew SBC-V2-005 platform using Atmel 39SF040 flash chips but has now been extended to be more generic in operation.
-
-Supported flash chips are 
-39SF040, 29F040,  AT49F040, AT29C040, M29F040 , MX29F040,  A29010B, A29040B
-
-The Atmel 39SF040 chip is recommended as it can erase and write 4Kb sectors. Other chips require the whole chip to be erased.
-
-## Usage
-
-In most cases, completing a ROM update is a simple as:
-
-1. Booting to the boot loader prompt
-2. Selecting option X - Xmodem Flash Updater
-3. Selecting option U - Update
-4. Initiating an X-modem transfer of your ROM image on your console device
-5. Selecting option R - Reboot
-
-If your console device is not able to transfer a ROM image i.e. your console is a VDU then you will have to use the console options to identify which character-input/output device is to be used as the serial device for transfer.
-
-When your console is the serial device used for the transfer, no progress information is displayed as this would disrupt the x-modem file transfer. If you use an alternate character-input/output devices as the serial device for the transfer then progress information will be displayed on the console device.
-
-Due to different platform processor speeds,  serials speeds and flow control capabilities the default console or serial device speed may need to be reduced for a successful transfer and flash to occur. The **Set Console Interface/Baud code** option at the Boot Loader can be used to change the speed if required. Additionally, the Updater has options to set to and revert from a recommended speed. 
-
-See the ROMWBW Applications guide for additional information on performing upgrades.
-
-## Console Options
-
-Option ( C ) - Set Console Device
-
-Option ( S ) - Set Serial Device
-
-By default the updater assumes that the current console is a serial device and that the ROM file to be flashed will also be transferred across this device, so the Console and Serial device are both the same.
-
-Either device can be can be change to another character-input/output device but the updater will always expect to receive the x-modem transfer on the **Serial Device**
-
-The advantage of transferring on a different device to the console is that progress information can be displayed during the transfer.
-
-Option ( > ) - Set Recommended Baud Rate
-
-Option ( < ) - Revert to Original Baud Rate
-
-## Programming options
-
-Option ( U ) - Begin Update
-
-The will begin the update process. The updater will expect to start receiving
-an x-modem file on the serial device unit.
-
-X-modem sends the file in packets of 128 bytes. The updater will cache 32
-packets which is 1 flash sector and then write that sector to the
-flash device.
-
-If using separate console, bank and sector progress information will shown
-
-```
-BANK 00 s00 s01 s02 s03 s04 s05 s06 s06 s07
-BANK 01 s00 s01 s02 s03 s04 s05 s06 s06 s07
-BANK 02 s00 s01 s02 s03 s04 s05 s06 s06 s07 etc
-```
-
-The x-modem file transfer protocol does not provide any filename or size
-information for the transfer so the updater does not perform any checks
-on the file suitability.
-
-The updater expects the file size to be a multiple of 4 kilobytes and
-will write all data received to the flash device. A system update
-file (128kb .img) or complete ROM can be received and written (512kb or
-1024kb .rom)
-
-If the update fails it is recommended that you retry before rebooting or
-exiting to the Boot loader as your machine may not be bootable.
-
-Option ( D ) - Duplicate flash #1 to flash #2
- 
-This option will make a copy of flash #1 onto flash #2. The purpose of this is to enable
- making a backup copy of the current flash. Intended for systems using 2x512Kb Flash devices.
-
-Option ( V ) - Toggle Write Verify
-
-By default each flash sector will be verified after being written. Slight
-performance improvements can be gained if turned off and could be used if
-you are experiencing reliable transfers and flashing.
-
-## Exit options
-
-Option ( R ) - Reboot
-
-Execute a cold reboot. This should be done after a successful update. If
-you perform a cold reboot after a failed update then it is likely that
-your system will be unusable and removing and reprogramming the flash
-will be required.
-
-Option ( Q ) - Quit to boot loader. 
-
-The SBC Boot Loader is reloaded from ROM and
-executed. After a successful update a Reboot should be performed. However,
-in the case of a failed update this option could be used to attempt to
-load CP/M and perform the normal x-modem / flash process to recover.
-
-## CRC Utility options
-
-Option ( 1 ) and ( 2 ) - Calculate and display CRC32 of 1st or 2nd 512k ROM.
-Option ( 3 ) - Calculate and display CRC32 of a 1024k (2x512Kb) ROM.
-
-Can be used to verify if a ROM image has been transferred and flashed correctly. Refer  to the Teraterm section below for details on configuring the automatic display of a files CRC after it has been transferred.
-
-In Windows, right clicking on a file should also give you a context menu option CRC SHA which will allow you to select a CRC32 calculation to be done on the selected file.
-
-## Tera Term macro configuration 
-
-Macros are a useful tool for automatic common tasks. There are a number of instances where using macros to facilitate the update process could be worthwhile if you are:
-
-* Following the ROMWBW development builds.
-* Doing lots of configuration changes.
-* Doing development on ROMWBW drivers
-
-Macros can be used to automate sending ROM updates or images and for my own purposed I have set up a separate macro for transferring each of the standard build ROM, my own custom configuration ROM and update ROM.
-
-An example macro file to send an *.upd file, using checksum mode and display the crc32 value of the transmitted file:
-
-```
-Xmodem send, checksum, display crc32
-xmodemsend '\\desktop\users\phillip\documents\github\romwbw\binary\sbc_std_cust.upd' 1
-crc32file crc '\\desktop\users\phillip\documents\github\romwbw\binary\sbc_std_cust.rom'
-sprintf '0x%08x' crc
-messagebox inputstr 'crc32'
-```
-
-## Serial speed guidelines
-
-As identified in the introduction, there are limitations on serial speed depending on processor speed and flow control settings. Listed below are some of the results identified during testing.
-
-Platform / Configuration       | Processor Speed | Maximum Serial Speed
--------------------------------|-----------------|---------------------
-SBC-V2  UART no flow control   | 2mhz            | 9600
-SBC-V2  UART no flow control   | 4mhz            | 19200
-SBC-V2  UART no flow control   | 5mhz            | 19200
-SBC-V2  UART no flow control   | 8mhz            | 38400
-SBC-V2  UART no flow control   | 10mhz           | 38400
-SBC-V2  USB-FIFO 2mhz+         |                 | n/a
-SBC-MK4 ASCI no flow control   | 18.432mhz       | 9600
-SBC-MK4 ASCI with flow control | 18.432mhz       | 38400
-
-The **Set Recommend Baud Rate** option in the Updater menu follows the following guidelines.
-
-Processor Speed | Baud Rate
-----------------|----------
-1Mhz            | 4800
-2-3Mhz          | 9600
-4-7Mhz          | 19200
-8-20Mhz         | 38400
-
-These can be customized in the updater.asm source code in the CLKTBL table  if desired.
-Feedback to the ROMWBW developers on these guidelines would be appreciated.
-
-## Notes:
-- All testing was done with Teraterm x-modem, Forcing checksum mode using macros was found to give  the most reliable transfer.
-- Partial writes can be completed with 39SF040 chips. Other chips require entire flash to be erased before being written.
-- An SBC V2-005 MegaFlash or Z80 MBC required for 1mb flash support. The Updater assumes both chips are same type
-- Failure handling has not been tested.
-- Timing broadly calibrated on a Z80 SBC-v2
-- UNA BIOS not supported

Source/Doc/ReadMe.md

@@ -114,7 +114,6 @@ Documentation for $doc_product$ includes:
 * $doc_user$
 * $doc_sys$
 * $doc_apps$
-* $doc_romapps$
 * $doc_errata$
 
 # Acknowledgments
@@ -188,6 +187,9 @@ please let me know if I missed you!
   compendium.
 
 * Martin R has provided substantial help reviewing and improving the
+  User Guide and Applications documents.
+  
+* Mark Pruden has also contributed a great deal of content to the
   User Guide.
 
 * Jacques Pelletier has contributed the DS1501 RTC driver code.

Source/Doc/SystemGuide.md

@@ -126,6 +126,7 @@ execution.
 
 ![Bank Switched Memory Layout](Graphics/BankSwitchedMemory){ width=100% }
 
+
 ## Bank Id
 
 RomWBW utilizes a specific assignment of memory banks for dedicated
@@ -262,6 +263,106 @@ Common Bank:
 It is a fixed mapping that is never changed in normal RomWBW operation
 hence the name "Common".
 
+# Disk Layout
+
+RomWBW supports two hard disk layouts: the Classic layout used by 
+RomWBW with 512 directory entries per slice and a Modern layout with 
+1024 directory entries per slice.  These layouts are referred to as
+hd512 and hd1k respectively.
+
+WARNING: You **can not** mix the two hard disk layouts on one hard 
+disk device.  You can use different layouts on different hard disk 
+devices in a single system though.
+
+RomWBW determines which of the hard disk layouts to use for a given 
+hard disk device based on whether there is a RomWBW hard disk 
+partition on the disk containing the slices.   If there is no RomWBW 
+partition, then RomWBW will assume the 512 directory entry format for 
+all slices and will assume the slices start at the first sector of 
+the hard disk.  If there is a RomWBW partition on the hard disk 
+device, then RomWBW will assume the 1024 directory entry format for 
+all slices and will assume the slices are located in the defined 
+partition.
+
+RomWBW supports up to 256 CP/M slices (0-255).  Under hd512, the slices
+begin at the start of the hard disk.  Under hd1k, the slices reside
+within partition type 0x2E.
+
+RomWBW accesses all hard disks using Logical Block Addressing (pure
+sector offset).  When necessary, RomWBW simulates the following disk
+geometry for operating systems:
+
+- Sector = 512 Bytes
+- Track = 16 Sectors (8KB per Track)
+- Cylinder = 16 Tracks (256 Sectors per Cylinder, 128KB per Cylinder)
+
+If one is used, the FAT Partition must not overlap the CP/M slices.
+The FAT partition does not need to start immediately after the CP/M
+slices nor does it need to extend to the end of the hard disk.  Its
+location and size are entirely determined by its corresponding
+partition table entry.
+
+Drive letters in CP/M are ASSIGNed to the numbered slices as desired.  
+At boot, RomWBW automatically assigns up to  8 slices to drive letters 
+starting with the first available drive letter (typically C:).
+
+Microsoft Windows will assign a single drive letter to the FAT partition
+when the CF/SD Card is inserted.  The drive letter assigned has no 
+relationship to the CP/M drive letters assigned to CP/M slices.
+
+In general, Windows, MacOS, or Linux know nothing about the CP/M slices 
+and CP/M knows nothing about the FAT partition.  However, the FAT 
+application can be run under CP/M to access the FAT partition 
+programmatically.
+
+A CP/M slice is (re)initialized using the CP/M command CLRDIR.  A CP/M 
+slice can be made bootable by copying system image to the System Area 
+using SYSCOPY.
+
+The FAT partition can be created from CP/M using the FDISK80 application.
+
+The FAT partition can be initialized using the FAT application from CP/M
+using the command `FAT FORMAT n:` where n is the RomWBW disk unit 
+number containing the FAT partition to be formatted.
+
+## Modern Disk Layout (hd1k)
+
+![Modern Disk Layout](Graphics/hd1k)
+
+The CP/M filesystem on a Modern disk will accommodate 1,024 directory 
+entries.
+
+The CP/M slices reside entirely within a hard disk partition of type
+0x2E.  The number of slices is determined by the number of slices that
+fit within the partition spaces allocated up to the maximum of 256.
+
+## Classic Disk Layout (hd512)
+
+![Classic Disk Layout](Graphics/hd512)
+
+The CP/M filesystem on a Classic disk will accommodate 512 directory 
+entries.
+
+The CP/M slices reside on the hard disk starting at the first sector
+of the hard disk.  The number of CP/M slices is not explicitly recorded
+anywhere on the hard disk.  It is up to the system user to know how
+many slices are being used based on the size of the hard disk media
+and/or the start of a FAT partition.
+
+A partition table may exist within the first sector of the first
+slice.  For Classic disks, the partition table defines only the
+location and size of the FAT partition.  The Partition Table does
+not control the location or number of CP/M slices in any way.
+
+The Partition Table resides in a sector that is shared with the System 
+Area of CP/M Slice 0.  However, the RomWBW implementation of CP/M takes 
+steps to avoid changing or corrupting the Partition Table area.
+
+The FAT partition can be created from CP/M using the FDISK80 
+application.  The user is responsible for ensuring that the start of the
+FAT partition does not overlap with the area they intend to use for 
+CP/M slices.  FDISK80 has a Reserve option to assist with this.
+
 # System Boot Process
 
 A multi-phase boot strategy is employed. This is necessary because at
@@ -746,12 +847,19 @@ more of the defined media types.
 | MID_FD111     | 9      | 8" 1.11M Floppy                            |
 | MID_HD1K      | 10     | Hard Disk (LBA) w/ 1024 directory entries  |
 
+**NOTE**: HBIOS does not actually differentiate between MID_HD512 and
+MID_HD1K.  The use of these two formats is determined by the use of a
+partition table on the media and is implemented by the operating
+system itself.  HBIOS treats all hard disks as raw sectors. See
+[Function 0x18 -- Disk Media (DIOMEDIA)] for more information on the
+Media ID byte returned.
+
 HBIOS supports both Cylinder/Head/Sector (CHS) and Logical Block 
 Addresses (CHS) when locating a sector for I/O (see DIOSEEK function). 
 For devices that are natively CHS (e.g., floppy disk), the HBIOS driver 
 can convert LBA values to CHS values according to the geometry of the 
 current media.  For devices that are natively LBA (e.g., hard disk), the
- HBIOS driver simulates CHS using a fictitious geometry provided by the 
+HBIOS driver simulates CHS using a fictitious geometry provided by the 
 driver (typically 16 sectors per track and 16 heads per cylinder).
 
 ### Function 0x10 -- Disk Status (DIOSTATUS)
@@ -964,6 +1072,12 @@ Report the Media ID (E) for the for media in the specified Disk Unit
 will be performed.  The Status (A) is a standard HBIOS result code. If 
 there is no media in device, function will return an error status.
 
+**NOTE**: This function will always return MID_HD512 for hard disk
+devices.  MID_HD1K is provided for use internally by operating systems
+that provide different filsystem formats depending on the partition
+table.  This function cannot be used to determine if an HD1K formatted
+partition exists on the hard disk.
+
 ### Function 0x19 -- Disk Define Media (DIODEFMED)
 
 | **Entry Parameters**                   | **Returned Values**                    |
@@ -997,7 +1111,7 @@ DIOMEDIA function to force this if desired.
 | **Entry Parameters**                   | **Returned Values**                    |
 |----------------------------------------|----------------------------------------|
 | B: 0x1B                                | A: Status                              |
-| C: Disk Unit                           | D: Heads                               |
+| C: Disk Unit                           | D: Heads / LBA                         |
 |                                        | E: Sectors                             |
 |                                        | HL: Cylinder Count                     |
 |                                        | BC: Block Size                         |
@@ -1007,7 +1121,11 @@ device uses LBA mode addressing natively, then the drivers simulated
 geometry will be returned. The Status (A) is a standard HBIOS result 
 code.  If the media is unknown, an error will be returned.
 
-Heads (D) refers to the number of heads per cylinder.  Sectors (E)
+LBA capability is indicated by D:7.  When set, the device is capable
+of LBA addressing.  Refer to [Function 0x12 -- Disk Seek (DIOSEEK)]
+for more information on specifying LBA vs. CHS addresses.
+
+Heads (D:6-0) refers to the number of heads per cylinder.  Sectors (E)
 refers to the number of sectors per track.  Cylinder Count (HL) is the
 total number of cylinders addressable for the media.  Block Size (BC)
 is the number of bytes in one sector.
@@ -2015,7 +2133,7 @@ sound will play for the duration defined in HL and then return.
 | **Entry Parameters**                   | **Returned Values**                    |
 |----------------------------------------|----------------------------------------|
 | B: 0x57                                | A: Status                              |
-| C: Disk Unit                           | C: Device Attributes                   |
+| C: Sound Unit                          | C: Device Attributes                   |
 |                                        | D: Device Type                         |
 |                                        | E: Device Number                       |
 |                                        | H: Device Unit Mode                    |
@@ -2038,6 +2156,17 @@ is servicing the specified unit.  Both of these values are considered
 driver specific.  Refer to the associated hardware driver for the values
 used.
 
+### Function 0x58 -- Sound Beep (SNDBEEP)
+
+| **Entry Parameters**                   | **Returned Values**                    |
+|----------------------------------------|----------------------------------------|
+| B: 0x58                                | A: Status                              |
+| C: Sound Unit                          |                                        |
+
+Play a beep tone on the specified Sound Unit (C).  The beep will
+normally be about 1/3 second in duration and the tone will be
+approximately B5.
+
 `\clearpage`{=latex}
 
 ## System (SYS)
@@ -2398,6 +2527,9 @@ a double-word binary value.  The frequency of the system timer in Hertz
 is returned in Frequency (C). The returned Status (A) is a standard HBIOS
 result code.
 
+The tick count is a 32 bit binary value.  It will rollover to zero
+if the maximum value for a 32 bit number is reached.
+
 Note that not all hardware configuration have a system timer.  You
 can determine if a timer exists by calling this function repeatedly
 to see if it is incrementing.

Source/FZ80/Build.cmd

@@ -5,17 +5,20 @@ set TOOLS=../../Tools
 
 set PATH=%TOOLS%\srecord;%PATH%
 
-if exist ..\..\Binary\FZ80_std.rom call :build_fz80
+for %%f in (..\..\Binary\FZ80_*.rom) do call :build %%~nf
 
 goto :eof
 
-:build_fz80
+:build
+echo.
+echo Creating %1 disk image...
+echo.
 
 srec_cat -generate 0x0 0x100000 --constant 0x00 -o temp.dat -binary
 srec_cat temp.dat -binary -exclude 0x1B8 0x200 fz80_ptbl.bin -binary -offset 0x1B8 -o temp.dat -binary
-srec_cat temp.dat -binary -exclude 0x80000 0xE0000 ..\..\Binary\FZ80_std.rom -binary -offset 0x80000 -o temp.dat -binary
-move temp.dat ..\..\Binary\hd1k_fz80_prefix.dat
+srec_cat temp.dat -binary -exclude 0x80000 0xE0000 ..\..\Binary\%1.rom -binary -offset 0x80000 -o temp.dat -binary
+move temp.dat ..\..\Binary\%1_hd1k_prefix.dat
 
-copy /b ..\..\Binary\hd1k_fz80_prefix.dat + ..\..\Binary\hd1k_cpm22.img + ..\..\Binary\hd1k_zsdos.img + ..\..\Binary\hd1k_nzcom.img + ..\..\Binary\hd1k_cpm3.img + ..\..\Binary\hd1k_zpm3.img + ..\..\Binary\hd1k_ws4.img ..\..\Binary\hd1k_fz80_combo.img || exit /b
+copy /b ..\..\Binary\%1_hd1k_prefix.dat + ..\..\Binary\hd1k_cpm22.img + ..\..\Binary\hd1k_zsdos.img + ..\..\Binary\hd1k_nzcom.img + ..\..\Binary\hd1k_cpm3.img + ..\..\Binary\hd1k_zpm3.img + ..\..\Binary\hd1k_ws4.img ..\..\Binary\%1_hd1k_combo.img || exit /b
 
 goto :eof

Source/FZ80/Makefile

@@ -1,24 +1,25 @@
-HD1KFZ80PREFIX = hd1k_fz80_prefix.dat
-HD1KFZ80COMBOIMG = hd1k_fz80_combo.img
-FZ80ROM = ../../Binary/FZ80_std.rom
-HD1KIMGS = ../../Binary/hd1k_cpm22.img ../../Binary/hd1k_zsdos.img ../../Binary/hd1k_nzcom.img \
-	../../Binary/hd1k_cpm3.img ../../Binary/hd1k_zpm3.img ../../Binary/hd1k_ws4.img
-
-OBJECTS := $(HD1KFZ80PREFIX) $(HD1KFZ80COMBOIMG)
-
 DEST=../../Binary
 
+HD1KIMGS = $(DEST)/hd1k_cpm22.img $(DEST)/hd1k_zsdos.img $(DEST)/hd1k_nzcom.img \
+	$(DEST)/hd1k_cpm3.img $(DEST)/hd1k_zpm3.img $(DEST)/hd1k_ws4.img
+
+ROMS := $(wildcard $(DEST)/FZ80_*.rom)
+ROMS := $(patsubst $(DEST)/%.rom,%,$(ROMS))
+
+OBJECTS := $(patsubst %,%_hd1k_prefix.dat,$(ROMS))
+OBJECTS += $(patsubst %,%_hd1k_combo.img,$(ROMS))
+
 TOOLS = ../../Tools
 
 include $(TOOLS)/Makefile.inc
 
 DIFFPATH = $(DIFFTO)/Binary
 
-$(HD1KFZ80PREFIX):
+%_hd1k_prefix.dat: $(DEST)/%.rom
 	srec_cat -generate 0x0 0x100000 --constant 0x00 -o temp.dat -binary
 	srec_cat temp.dat -binary -exclude 0x1B8 0x200 fz80_ptbl.bin -binary -offset 0x1B8 -o temp.dat -binary
-	srec_cat temp.dat -binary -exclude 0x80000 0xE0000 $(FZ80ROM) -binary -offset 0x80000 -o temp.dat -binary
+	srec_cat temp.dat -binary -exclude 0x80000 0xE0000 $< -binary -offset 0x80000 -o temp.dat -binary
 	mv temp.dat $@
 
-$(HD1KFZ80COMBOIMG): $(HD1KFZ80PREFIX) $(HD1KIMGS)
+%_hd1k_combo.img: %_hd1k_prefix.dat  $(HD1KIMGS)
 	cat $^ > $@

Source/HBIOS/Bank Layout.txt

@@ -43,8 +43,8 @@ Standard RAM Bank Layout (512K)
 Bank ID         Usage
 -------         ------
 0x80            RomWBW HBIOS
-0x81-0x88       RAM Disk Data (3)
-0x89-0x8B	App Banks (8)
+0x81-0x88       RAM Disk Data (8)
+0x89-0x8B	App Banks (3)
 0x8C		CP/M 3 Buffers
 0x8D            CP/M 3 OS
 0x8E            User TPA

Source/HBIOS/Build.cmd

@@ -211,31 +211,29 @@ call Build ZETA2 std || exit /b
 call Build N8 std || exit /b
 call Build MK4 std || exit /b
 call Build RCZ80 std || exit /b
-call Build RCZ80 kio || exit /b
-call Build RCZ80 easy || exit /b
-call Build RCZ80 tiny || exit /b
-call Build RCZ80 skz || exit /b
-:: call Build RCZ80 mt || exit /b
-:: call Build RCZ80 duart || exit /b
-call Build RCZ80 zrc || exit /b
-call Build RCZ80 zrc_ram || exit /b
-call Build RCZ80 zrc512 || exit /b
-call Build RCZ180 ext || exit /b
-call Build RCZ180 nat || exit /b
-call Build RCZ180 z1rcc || exit /b
-call Build RCZ280 ext || exit /b
-call Build RCZ280 nat || exit /b
-call Build RCZ280 zz80mb || exit /b
-call Build RCZ280 zzrcc || exit /b
-call Build RCZ280 zzrcc_ram || exit /b
-call Build SCZ180 sc126 || exit /b
-call Build SCZ180 sc130 || exit /b
-call Build SCZ180 sc131 || exit /b
-call Build SCZ180 sc140 || exit /b
-call Build SCZ180 sc503 || exit /b
-call Build SCZ180 sc700 || exit /b
+call Build RCZ80 kio_std || exit /b
+call Build RCZ80 easy_std || exit /b
+call Build RCZ80 tiny_std || exit /b
+call Build RCZ80 skz_std || exit /b
+call Build RCZ80 zrc_std || exit /b
+call Build RCZ80 zrc_ram_std || exit /b
+call Build RCZ80 zrc512_std || exit /b
+call Build RCZ180 ext_std || exit /b
+call Build RCZ180 nat_std || exit /b
+call Build RCZ180 z1rcc_std || exit /b
+call Build RCZ280 ext_std || exit /b
+call Build RCZ280 nat_std || exit /b
+call Build RCZ280 zz80mb_std || exit /b
+call Build RCZ280 zzrcc_std || exit /b
+call Build RCZ280 zzrcc_ram_std || exit /b
+call Build SCZ180 sc126_std || exit /b
+call Build SCZ180 sc130_std || exit /b
+call Build SCZ180 sc131_std || exit /b
+call Build SCZ180 sc140_std || exit /b
+call Build SCZ180 sc503_std || exit /b
+call Build SCZ180 sc700_std || exit /b
+call Build GMZ180 std || exit /b
 call Build DYNO std || exit /b
-call Build UNA std || exit /b
 call Build RPH std || exit /b
 call Build Z80RETRO std || exit /b
 call Build S100 std || exit /b
@@ -245,5 +243,6 @@ call Build EPITX std || exit /b
 :: call Build MON std || exit /b
 call Build NABU std || exit /b
 call Build FZ80 std || exit /b
+call Build UNA std || exit /b
 
 goto :eof

Source/HBIOS/Build.ps1

@@ -28,7 +28,7 @@ $ErrorAction = 'Stop'
 #
 
 $PlatformListZ80 = "SBC", "MBC", "ZETA", "ZETA2", "RCZ80", "Z80RETRO", "DUO", "UNA", "HEATH", "MON", "NABU", "FZ80"
-$PlatformListZ180 = "N8", "MK4", "RCZ180", "SCZ180", "DYNO", "RPH", "S100", "EPITX"
+$PlatformListZ180 = "N8", "MK4", "RCZ180", "SCZ180", "DYNO", "RPH", "S100", "EPITX", "GMZ180"
 $PlatformListZ280 = "RCZ280"
 
 #

Source/HBIOS/Build.sh

@@ -11,48 +11,47 @@ export CPUFAM
 
 if [ "${ROM_PLATFORM}" == "dist" ] ; then
 	echo "!!!DISTRIBUTION BUILD!!!"
-	ROM_PLATFORM="DYNO"; ROM_CONFIG="std"; bash Build.sh
-	ROM_PLATFORM="MK4"; ROM_CONFIG="std"; bash Build.sh
-	ROM_PLATFORM="N8"; ROM_CONFIG="std"; bash Build.sh
-	ROM_PLATFORM="RCZ180"; ROM_CONFIG="ext"; bash Build.sh
-	ROM_PLATFORM="RCZ180"; ROM_CONFIG="nat"; bash Build.sh
-	ROM_PLATFORM="RCZ180"; ROM_CONFIG="z1rcc"; bash Build.sh
-	ROM_PLATFORM="RCZ280"; ROM_CONFIG="ext"; bash Build.sh
-	ROM_PLATFORM="RCZ280"; ROM_CONFIG="nat"; bash Build.sh
-	ROM_PLATFORM="RCZ280"; ROM_CONFIG="zz80mb"; bash Build.sh
-	ROM_PLATFORM="RCZ280"; ROM_CONFIG="zzrcc"; bash Build.sh
-	ROM_PLATFORM="RCZ280"; ROM_CONFIG="zzrcc_ram"; bash Build.sh
-#	ROM_PLATFORM="RCZ80"; ROM_CONFIG="mt"; bash Build.sh
-#	ROM_PLATFORM="RCZ80"; ROM_CONFIG="duart"; bash Build.sh
-	ROM_PLATFORM="RCZ80"; ROM_CONFIG="std"; bash Build.sh
-	ROM_PLATFORM="RCZ80"; ROM_CONFIG="kio"; bash Build.sh
-	ROM_PLATFORM="RCZ80"; ROM_CONFIG="easy"; bash Build.sh
-	ROM_PLATFORM="RCZ80"; ROM_CONFIG="tiny"; bash Build.sh
-	ROM_PLATFORM="RCZ80"; ROM_CONFIG="skz"; bash Build.sh
-	ROM_PLATFORM="RCZ80"; ROM_CONFIG="zrc"; bash Build.sh
-	ROM_PLATFORM="RCZ80"; ROM_CONFIG="zrc_ram"; bash Build.sh
-	ROM_PLATFORM="RCZ80"; ROM_CONFIG="zrc512"; bash Build.sh
-	ROM_PLATFORM="RPH"; ROM_CONFIG="std"; bash Build.sh
 	ROM_PLATFORM="SBC"; ROM_CONFIG="std"; bash Build.sh
 	ROM_PLATFORM="SBC"; ROM_CONFIG="simh"; bash Build.sh
 	ROM_PLATFORM="MBC"; ROM_CONFIG="std"; bash Build.sh
-	ROM_PLATFORM="DUO"; ROM_CONFIG="std"; bash Build.sh
-	ROM_PLATFORM="SCZ180"; ROM_CONFIG="sc126"; bash Build.sh
-	ROM_PLATFORM="SCZ180"; ROM_CONFIG="sc130"; bash Build.sh
-	ROM_PLATFORM="SCZ180"; ROM_CONFIG="sc131"; bash Build.sh
-	ROM_PLATFORM="SCZ180"; ROM_CONFIG="sc140"; bash Build.sh
-	ROM_PLATFORM="SCZ180"; ROM_CONFIG="sc503"; bash Build.sh
-	ROM_PLATFORM="SCZ180"; ROM_CONFIG="sc700"; bash Build.sh
-	ROM_PLATFORM="S100"; ROM_CONFIG="std"; bash Build.sh
-	ROM_PLATFORM="UNA"; ROM_CONFIG="std"; bash Build.sh
-	ROM_PLATFORM="Z80RETRO"; ROM_CONFIG="std"; bash Build.sh
 	ROM_PLATFORM="ZETA"; ROM_CONFIG="std"; bash Build.sh
 	ROM_PLATFORM="ZETA2"; ROM_CONFIG="std"; bash Build.sh
+	ROM_PLATFORM="N8"; ROM_CONFIG="std"; bash Build.sh
+	ROM_PLATFORM="MK4"; ROM_CONFIG="std"; bash Build.sh
+	ROM_PLATFORM="RCZ80"; ROM_CONFIG="std"; bash Build.sh
+	ROM_PLATFORM="RCZ80"; ROM_CONFIG="kio_std"; bash Build.sh
+	ROM_PLATFORM="RCZ80"; ROM_CONFIG="easy_std"; bash Build.sh
+	ROM_PLATFORM="RCZ80"; ROM_CONFIG="tiny_std"; bash Build.sh
+	ROM_PLATFORM="RCZ80"; ROM_CONFIG="skz_std"; bash Build.sh
+	ROM_PLATFORM="RCZ80"; ROM_CONFIG="zrc_std"; bash Build.sh
+	ROM_PLATFORM="RCZ80"; ROM_CONFIG="zrc_ram_std"; bash Build.sh
+	ROM_PLATFORM="RCZ80"; ROM_CONFIG="zrc512_std"; bash Build.sh
+	ROM_PLATFORM="RCZ180"; ROM_CONFIG="ext_std"; bash Build.sh
+	ROM_PLATFORM="RCZ180"; ROM_CONFIG="nat_std"; bash Build.sh
+	ROM_PLATFORM="RCZ180"; ROM_CONFIG="z1rcc_std"; bash Build.sh
+	ROM_PLATFORM="RCZ280"; ROM_CONFIG="ext_std"; bash Build.sh
+	ROM_PLATFORM="RCZ280"; ROM_CONFIG="nat_std"; bash Build.sh
+	ROM_PLATFORM="RCZ280"; ROM_CONFIG="zz80mb_std"; bash Build.sh
+	ROM_PLATFORM="RCZ280"; ROM_CONFIG="zzrcc_std"; bash Build.sh
+	ROM_PLATFORM="RCZ280"; ROM_CONFIG="zzrcc_ram_std"; bash Build.sh
+	ROM_PLATFORM="SCZ180"; ROM_CONFIG="sc126_std"; bash Build.sh
+	ROM_PLATFORM="SCZ180"; ROM_CONFIG="sc130_std"; bash Build.sh
+	ROM_PLATFORM="SCZ180"; ROM_CONFIG="sc131_std"; bash Build.sh
+	ROM_PLATFORM="SCZ180"; ROM_CONFIG="sc140_std"; bash Build.sh
+	ROM_PLATFORM="SCZ180"; ROM_CONFIG="sc503_std"; bash Build.sh
+	ROM_PLATFORM="SCZ180"; ROM_CONFIG="sc700_std"; bash Build.sh
+	ROM_PLATFORM="GMZ180"; ROM_CONFIG="std"; bash Build.sh
+	ROM_PLATFORM="DYNO"; ROM_CONFIG="std"; bash Build.sh
+	ROM_PLATFORM="RPH"; ROM_CONFIG="std"; bash Build.sh
+	ROM_PLATFORM="Z80RETRO"; ROM_CONFIG="std"; bash Build.sh
+	ROM_PLATFORM="S100"; ROM_CONFIG="std"; bash Build.sh
+	ROM_PLATFORM="DUO"; ROM_CONFIG="std"; bash Build.sh
 	ROM_PLATFORM="HEATH"; ROM_CONFIG="std"; bash Build.sh
 	ROM_PLATFORM="EPITX"; ROM_CONFIG="std"; bash Build.sh
 #	ROM_PLATFORM="MON"; ROM_CONFIG="std"; bash Build.sh
 	ROM_PLATFORM="NABU"; ROM_CONFIG="std"; bash Build.sh
 	ROM_PLATFORM="FZ80"; ROM_CONFIG="std"; bash Build.sh
+	ROM_PLATFORM="UNA"; ROM_CONFIG="std"; bash Build.sh
 	exit
 fi
 

Source/HBIOS/Config/DUO_std.asm

@@ -1,30 +1,50 @@
 ;
 ;==================================================================================================
-;   DUODYNE STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR DUODYNE
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_duo.asm"
+#include "cfg_DUO.asm"
 ;
 CPUOSC		.SET	8000000		; CPU OSC FREQ IN MHZ
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP

Source/HBIOS/Config/DYNO_std.asm

@@ -1,30 +1,50 @@
 ;
 ;==================================================================================================
-;   DYNO STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR DYNO
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_dyno.asm"
+#include "cfg_DYNO.asm"
 ;
 CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP

Source/HBIOS/Config/EPITX_std.asm

@@ -1,32 +1,52 @@
 ;
 ;==================================================================================================
-;   Z180 Mini ITX STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR Z180 MINI ITX
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	PLATFORM_NAME	"Z180 MiniITX"
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_epitx.asm"
+#include "cfg_EPITX.asm"
 ;
 CRTACT		.SET	TRUE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
 ;

Source/HBIOS/Config/FZ80_std.asm

@@ -1,34 +1,50 @@
 ;
 ;==================================================================================================
-;   S100 FPGZ Z80 STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR S100 FPGA Z80
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_fz80.asm"
+#include "cfg_FZ80.asm"
 ;
 CPUOSC		.SET	8000000		; CPU OSC FREQ IN MHZ
 CRTACT		.SET	TRUE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
-;
-; SD CARD SUPPORT CURRENTLY BROKEN
-SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
-SDTRACE		.SET	3		; SD: TRACE LEVEL (0=NO,1=ERRORS,2=ALL)

Source/HBIOS/Config/GMZ180_std.asm

@@ -0,0 +1,92 @@
+;
+;==================================================================================================
+;   ROMWBW DEFAULT BUILD SETTINGS FOR GENESIS STD Z180
+;==================================================================================================
+;
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
+;
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
+;
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
+;
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
+;
+#DEFINE PLATFORM_NAME "GM STD BUS Z180", " [", CONFIG, "]"
+;
+#DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
+;
+#include "cfg_GMZ180.asm"
+;
+CPUOSC	.SET	18432000	; CPU OSC FREQ IN MHZ
+CRTACT	.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
+;
+Z180_CLKDIV	.SET	1		; Z180: CHK DIV: 0=OSC/2, 1=OSC, 2=OSC*2
+Z180_MEMWAIT	.SET	0		; Z180: MEMORY WAIT STATES (0-3)
+Z180_IOWAIT	.SET	1		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
+;
+LEDENABLE	.SET	FALSE		; ENABLE STATUS LED (SINGLE LED)
+LEDMODE	.SET	LEDMODE_STD	; LEDMODE_[STD|SC|RTC|NABU]
+;
+FPLED_ENABLE	.SET	FALSE		; FP: ENABLES FRONT PANEL LEDS
+FPLED_IO	.SET	$00		; FP: PORT ADDRESS FOR FP LEDS
+;
+DSRTCENABLE	.SET	TRUE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
+INTRTCENABLE	.SET	TRUE		; ENABLE PERIODIC INTERRUPT CLOCK DRIVER (INTRTC.ASM)
+;
+UARTENABLE	.SET	FALSE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+ASCIENABLE	.SET	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
+ACIAENABLE	.SET	FALSE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
+SIOENABLE	.SET	FALSE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
+;
+TMSENABLE	.SET	FALSE		; TMS: ENABLE TMS9918 VIDEO/KBD DRIVER (TMS.ASM)
+TMSTIMENABLE	.SET	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
+TMSMODE	.SET	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MSXKBD|COLECO]
+MKYENABLE	.SET	FALSE		; MSX 5255 PPI KEYBOARD COMPATIBLE DRIVER (REQUIRES TMS VDA DRIVER)
+EFENABLE	.SET	FALSE		; EF: ENABLE EF9345 VIDEO DRIVER (EF.ASM)
+VDAEMU_SERKBD	.SET	0		; VDA EMULATION: SERIAL KBD UNIT #, OR $FF FOR HW KBD
+;
+AY38910ENABLE	.SET	FALSE		; AY: AY-3-8910 / YM2149 SOUND DRIVER
+AYMODE		.SET	AYMODE_RCZ180	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LINC]
+SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
+;
+FDENABLE	.SET	FALSE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
+FDMODE	.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPWDC]
+;
+IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
+PPIDEENABLE	.SET	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
+SDENABLE	.SET	TRUE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
+SDMODE	.SET	SDMODE_GM	; SD: DRIVER MODE: SDMODE_[JUHA|N8|CSIO|PPI|UART|DSD|MK4|SC|MT|USR]
+SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD & SC ONLY
+;
+PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)

Source/HBIOS/Config/HEATH_std.asm

@@ -1,69 +1,48 @@
 ;
 ;==================================================================================================
-;   HEATH H8 Z80 STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR HEATH H8 Z80
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz80.asm"
+#include "cfg_HEATH.asm"
 ;
-CPUOSC		.SET	7372800		; CPU OSC FREQ IN MHZ
-CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
-;
-DSKYENABLE	.SET	TRUE		; ENABLES DSKY FUNCTIONALITY
-H8PENABLE	.SET	TRUE		; ENABLES HEATH H8 FRONT PANEL
-;
-FPLED_ENABLE	.SET	TRUE		; FP: ENABLES FRONT PANEL LEDS
-FPSW_ENABLE	.SET	TRUE		; FP: ENABLES FRONT PANEL SWITCHES
-;
-DSRTCENABLE	.SET	TRUE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
-RP5RTCENABLE	.SET	FALSE		; RP5C01 RTC BASED CLOCK (RP5RTC.ASM)
-;
-UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
-ACIAENABLE	.SET	TRUE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
-SIOENABLE	.SET	TRUE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
-DUARTENABLE	.SET	FALSE		; DUART: ENABLE 2681/2692 SERIAL DRIVER (DUART.ASM)
-;
-LPTENABLE	.SET	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
-;
-TMSENABLE	.SET	FALSE		; TMS: ENABLE TMS9918 VIDEO/KBD DRIVER (TMS.ASM)
-TMSTIMENABLE	.SET	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
-TMSMODE		.SET	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MSXKBD|COLECO]
-MKYENABLE	.SET	FALSE		; MSX 5255 PPI KEYBOARD COMPATIBLE DRIVER (REQUIRES TMS VDA DRIVER)
-VRCENABLE	.SET	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
-VDAEMU_SERKBD	.SET	0		; VDA EMULATION: SERIAL KBD UNIT #, OR $FF FOR HW KBD
-;
-AY38910ENABLE	.SET	FALSE		; AY: AY-3-8910 / YM2149 SOUND DRIVER
-AYMODE		.SET	AYMODE_RCZ80	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LINC]
-SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
-;
-FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
-FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
-;
-IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
-PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
-SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
-SDMODE		.SET	SDMODE_PIO	; SD: DRIVER MODE: SDMODE_[JUHA|N8|CSIO|PPI|UART|DSD|MK4|SC|MT|PIO|USR]
-SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
-IMMENABLE	.SET	FALSE		; IMM: ENABLE IMM DISK DRIVER (IMM.ASM)
-;
-PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)

Source/HBIOS/Config/MBC_std.asm

@@ -1,30 +1,50 @@
 ;
 ;==================================================================================================
-;   MBC CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR NHYODYNE
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_mbc.asm"
+#include "cfg_MBC.asm"
 ;
 CPUOSC		.SET	8000000		; CPU OSC FREQ IN MHZ
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP

Source/HBIOS/Config/MK4_std.asm

@@ -1,30 +1,50 @@
 ;
 ;==================================================================================================
-;   MARK IV STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR MARK IV
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_mk4.asm"
+#include "cfg_MK4.asm"
 ;
 CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
 INTMODE		.SET	2		; INTERRUPTS: 0=NONE, 1=MODE 1, 2=MODE 2
@@ -35,9 +55,6 @@ Z180_MEMWAIT	.SET	0		; Z180: MEMORY WAIT STATES (0-3)
 Z180_IOWAIT	.SET	1		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
 ;
 UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
-UARTCAS		.SET	TRUE		; UART: AUTO-DETECT ECB CASSETTE UART
-UARTMFP		.SET	TRUE		; UART: AUTO-DETECT MF/PIC UART
-UART4		.SET	TRUE		; UART: AUTO-DETECT 4UART UART
 SIOENABLE	.SET	FALSE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
 ;
 TMSENABLE	.SET	FALSE		; TMS: ENABLE TMS9918 VIDEO/KBD DRIVER (TMS.ASM)

Source/HBIOS/Config/MON_std.asm

@@ -1,30 +1,50 @@
 ;
 ;==================================================================================================
-;   MONSPUTER Z80 STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR MONSPUTER Z80
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_mon.asm"
+#include "cfg_MON.asm"
 ;
 CPUOSC		.SET	4000000		; CPU OSC FREQ IN MHZ
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP

Source/HBIOS/Config/N8_std.asm

@@ -1,30 +1,50 @@
 ;
 ;==================================================================================================
-;   N8 STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR N8
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_n8.asm"
+#include "cfg_N8.asm"
 ;
 CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
 INTMODE		.SET	2		; INTERRUPTS: 0=NONE, 1=MODE 1, 2=MODE 2

Source/HBIOS/Config/NABU_std.asm

@@ -1,32 +1,52 @@
 ;
 ;==================================================================================================
-;   NABU Z80 STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR NABU Z80
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_nabu.asm"
+#include "cfg_NABU.asm"
 ;
 CRTACT		.SET	TRUE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
 ;
-TMSMODE		.SET	TMSMODE_NABU80	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MSXKBD|COLECO|DUO|NABU40|NABU80]
+TMS80COLS	.SET	TRUE	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MSXKBD|COLECO|DUO|NABU40|NABU80]
 

Source/HBIOS/Config/RCZ180_ext_std.asm

@@ -1,30 +1,50 @@
 ;
 ;==================================================================================================
-;   RCBUS Z180 STANDARD CONFIGURATION (EXTERNAL MMU ON 512K RAM/ROM BANKED MEMORY MODULE)
+;   ROMWBW DEFAULT BUILD SETTINGS FOR RCBUS Z180 W/ EXTERNAL Z2 MMU
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz180.asm"
+#include "cfg_RCZ180.asm"
 ;
 CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP

Source/HBIOS/Config/RCZ180_nat_std.asm

@@ -1,30 +1,50 @@
 ;
 ;==================================================================================================
-;   RCBUS Z180 STANDARD CONFIGURATION (NATIVE Z180 MMU W/ LINEAR MEMORY MODULE)
+;   ROMWBW DEFAULT BUILD SETTINGS FOR RCBUS Z180 W/ NATIVE Z180 MMU
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz180.asm"
+#include "cfg_RCZ180.asm"
 ;
 CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP

Source/HBIOS/Config/RCZ180_z1rcc_std.asm

@@ -1,32 +1,52 @@
 ;
 ;==================================================================================================
-;   RCBUS Z180 Z1RCC CONFIGURATION (ROMLESS)
+;   ROMWBW DEFAULT BUILD SETTINGS FOR RCBUS Z180 ROMLESS Z1RCC
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE PLATFORM_NAME "Z1RCC", " [", CONFIG, "]"
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz180.asm"
+#include "cfg_RCZ180.asm"
 ;
 CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP

Source/HBIOS/Config/RCZ280_ext_std.asm

@@ -1,30 +1,50 @@
 ;
 ;==================================================================================================
-;   RCBUS Z280 STANDARD CONFIGURATION (EXTERNAL MMU ON 512K RAM/ROM BANKED MEMORY MODULE)
+;   ROMWBW DEFAULT BUILD SETTINGS FOR RCBUS Z280 W/ EXTERNAL Z2 MMU
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz280.asm"
+#include "cfg_RCZ280.asm"
 ;
 CPUOSC		.SET	24000000	; CPU OSC FREQ IN MHZ
 INTMODE		.SET	1		; INTERRUPTS: 0=NONE, 1=MODE 1, 2=MODE 2

Source/HBIOS/Config/RCZ280_nat_std.asm

@@ -1,30 +1,50 @@
 ;
 ;==================================================================================================
-;   RCBUS Z280 STANDARD CONFIGURATION (NATIVE Z280 MMU W/ LINEAR MEMORY)
+;   ROMWBW DEFAULT BUILD SETTINGS FOR RCBUS Z280 W/ NATIVE Z280 MMU
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz280.asm"
+#include "cfg_RCZ280.asm"
 ;
 CPUOSC		.SET	24000000	; CPU OSC FREQ IN MHZ
 INTMODE		.SET	3		; INTERRUPTS: 0=NONE, 1=MODE 1, 2=MODE 2

Source/HBIOS/Config/RCZ280_zz80mb_std.asm

@@ -1,32 +1,52 @@
 ;
 ;==================================================================================================
-;   RCBUS Z280 STANDARD CONFIGURATION (NATIVE Z280 MMU W/ LINEAR MEMORY ON ZZ80MB)
+;   ROMWBW DEFAULT BUILD SETTINGS FOR RCBUS ZZ80MB Z280 W/ NATIVE Z280 MMU
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE PLATFORM_NAME "ZZ80MB", " [", CONFIG, "]"
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz280.asm"
+#include "cfg_RCZ280.asm"
 ;
 CPUOSC		.SET	24000000	; CPU OSC FREQ IN MHZ
 INTMODE		.SET	3		; INTERRUPTS: 0=NONE, 1=MODE 1, 2=MODE 2

Source/HBIOS/Config/RCZ280_zzrcc_ram_std.asm

@@ -1,32 +1,52 @@
 ;
 ;==================================================================================================
-;   RCBUS Z280 ZZRCC CONFIGURATION (ROMLESS)
+;   ROMWBW DEFAULT BUILD SETTINGS FOR RCBUS Z280 ROMLESS ZZRCC W/ NATIVE Z280 MMU
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE PLATFORM_NAME "ZZRCC", " [", CONFIG, "]"
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz280.asm"
+#include "cfg_RCZ280.asm"
 ;
 CPUOSC		.SET	29491200	; CPU OSC FREQ IN MHZ
 INTMODE		.SET	3		; INTERRUPTS: 0=NONE, 1=MODE 1, 2=MODE 2

Source/HBIOS/Config/RCZ280_zzrcc_std.asm

@@ -1,32 +1,52 @@
 ;
 ;==================================================================================================
-;   RCBUS Z280 ZZRCC CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR RCBUS Z280 ZZRCC W/ NATIVE Z280 MMU
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE PLATFORM_NAME "ZZRCC", " [", CONFIG, "]"
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz280.asm"
+#include "cfg_RCZ280.asm"
 ;
 CPUOSC		.SET	29491200	; CPU OSC FREQ IN MHZ
 INTMODE		.SET	3		; INTERRUPTS: 0=NONE, 1=MODE 1, 2=MODE 2

Source/HBIOS/Config/RCZ80_easy_std.asm

@@ -1,32 +1,52 @@
 ;
 ;==================================================================================================
-;   EASY Z80 STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR EASY Z80
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE PLATFORM_NAME "Easy-Z80", " [", CONFIG, "]"
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz80.asm"
+#include "cfg_RCZ80.asm"
 ;
 PLATFORM	.SET	PLT_EZZ80	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH]
 CPUOSC		.SET	10000000	; CPU OSC FREQ IN MHZ

Source/HBIOS/Config/RCZ80_jbl.asm

@@ -1,8 +1,49 @@
 ;
 ;==================================================================================================
-;   RCBUS Z80 COLECOVISION-COMPATIBLE CONFIGURATION FOR J.B. LANGSTON'S GAME BOARDS
+;   ROMWBW DEFAULT BUILD SETTINGS FOR RCBUS Z80 W/ JBL GAME BOARDS
 ;==================================================================================================
 ;
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
+;
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
+;
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
+;
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
+;
+; NOTES:
+;
 ; THIS CONFIGURATION ENABLES DRIVERS FOR THE TMS9918 AND SN76489 BOARDS BY J.B. LANGSTON
 ; AND THE YM2149 BOARD BY ED BRINDLEY. THE TMS9918 IS CONFIGURED TO USE THE COLECOVISION
 ; PORTS AND HAS INTERRUPTS DISABLED BECAUSE COLECOVISION USES NMI, WHICH WOULD BREAK CP/M
@@ -22,16 +63,9 @@
 ; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
 ; YOUR FILE IN THE BUILD PROCESS.
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
-;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
-;
 #DEFINE	BOOT_DEFAULT	"Z"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz80.asm"
+#include "cfg_RCZ80.asm"
 ;
 CPUOSC		.SET	3686400		; CPU OSC FREQ IN MHZ
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP

Source/HBIOS/Config/RCZ80_kio_std.asm

@@ -1,30 +1,50 @@
 ;
 ;==================================================================================================
-;   RCBUS Z80 STANDARD CONFIGURATION W/ KIO
+;   ROMWBW DEFAULT BUILD SETTINGS FOR RCBUS Z80 W/ KIO
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz80.asm"
+#include "cfg_RCZ80.asm"
 ;
 CPUOSC		.SET	7372800		; CPU OSC FREQ IN MHZ
 INTMODE		.SET	2		; INTERRUPTS: 0=NONE, 1=MODE 1, 2=MODE 2

Source/HBIOS/Config/RCZ80_skz_std.asm

@@ -1,30 +1,50 @@
 ;
 ;==================================================================================================
-;   RCBUS Z80 STANDARD CONFIGURATION W/ SERGEY KISELEV Z80 + 512K CPU
+;   ROMWBW DEFAULT BUILD SETTINGS FOR RCBUS Z80 W/ SERGEY KISELEL Z80+512K CPU
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz80.asm"
+#include "cfg_RCZ80.asm"
 ;
 CPUOSC		.SET	7372800		; CPU OSC FREQ IN MHZ
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP

Source/HBIOS/Config/RCZ80_std.asm

@@ -1,30 +1,50 @@
 ;
 ;==================================================================================================
-;   RCBUS Z80 STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR RCBUS Z80
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz80.asm"
+#include "cfg_RCZ80.asm"
 ;
 CPUOSC		.SET	7372800		; CPU OSC FREQ IN MHZ
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -45,7 +65,6 @@ LPTENABLE	.SET	FALSE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)
 TMSENABLE	.SET	FALSE		; TMS: ENABLE TMS9918 VIDEO/KBD DRIVER (TMS.ASM)
 TMSTIMENABLE	.SET	FALSE		; TMS: ENABLE TIMER INTERRUPTS (REQUIRES IM1)
 TMSMODE		.SET	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MSXKBD|COLECO]
-MKYENABLE	.SET	FALSE		; MSX 5255 PPI KEYBOARD COMPATIBLE DRIVER (REQUIRES TMS VDA DRIVER)
 VRCENABLE	.SET	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
 EFENABLE	.SET	FALSE		; EF: ENABLE EF9345 VIDEO DRIVER (EF.ASM)
 VDAEMU_SERKBD	.SET	0		; VDA EMULATION: SERIAL KBD UNIT #, OR $FF FOR HW KBD

Source/HBIOS/Config/RCZ80_tiny_std.asm

@@ -1,32 +1,52 @@
 ;
 ;==================================================================================================
-;   TINY Z80 STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR TINY Z80
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE PLATFORM_NAME "Tiny-Z80", " [", CONFIG, "]"
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz80.asm"
+#include "cfg_RCZ80.asm"
 ;
 PLATFORM	.SET	PLT_EZZ80	; PLT_[SBC|ZETA|ZETA2|N8|MK4|UNA|RCZ80|RCZ180|EZZ80|SCZ180|DYNO|RCZ280|MBC|RPH]
 CPUOSC		.SET	16000000	; CPU OSC FREQ IN MHZ

Source/HBIOS/Config/RCZ80_user.asm

@@ -0,0 +1,57 @@
+;
+;==================================================================================================
+;   ROMWBW CUSTOM USER BUILD SETTINGS EXAMPLE FOR RCBUS Z80
+;==================================================================================================
+;
+; THIS FILE IS AN EXAMPLE OF A CUSTOM USER SETTINGS FILE.  THESE
+; SETTINGS OVERRIDE THE DEFAULT SETTINGS OF THE INHERITED FILES AS
+; DESIRED BY A USER.
+;
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
+;
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
+;
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; THIS FILE EXEMPLIFIES THE IDEAL WAY TO CREATE A USER SPECIFIC BUILD
+; CONFIGURATION.  NOTICE THAT IT INCLUDES THE DEFAULT BUILD SETTINGS
+; FILE AND OVERRIDES SOME DESIRED SETTINGS.
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
+;
+; THIS EXAMPLE CUSTOM USER SETTINGS FILE DOES THE FOLLOWING:
+;
+; 1. SETS A CUSTOM NAME USED IN THE BOOT LOADER BANNER
+; 2. BOOTS ZSDOS BY DEFAULT AFTER 10 SECOND DELAY
+; 3. ENABLES LPT PRINTER SUPPORT
+;
+#DEFINE PLATFORM_NAME "My Custom RCBus Computer", " [", CONFIG, "]"
+#DEFINE	BOOT_DEFAULT "Z"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
+;
+#include "Config/RCZ80_std.asm"		; INHERIT FROM OFFICIAL BUILD SETTINGS
+;
+BOOT_TIMEOUT	.SET	10		; AUTO BOOT TIMEOUT IN SECONDS, -1 TO DISABLE, 0 FOR IMMEDIATE
+;
+LPTENABLE	.SET	TRUE		; LPT: ENABLE CENTRONICS PRINTER DRIVER (LPT.ASM)

Source/HBIOS/Config/RCZ80_zrc512_std.asm

@@ -1,32 +1,52 @@
 ;
 ;==================================================================================================
-;   RCBUS Z80 ZRC512 CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR RCBUS Z80 ZRC512
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE PLATFORM_NAME "ZRC512", " [", CONFIG, "]"
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz80.asm"
+#include "cfg_RCZ80.asm"
 ;
 CPUOSC		.SET	22000000	; CPU OSC FREQ IN MHZ
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP

Source/HBIOS/Config/RCZ80_zrc_ram_std.asm

@@ -1,32 +1,52 @@
 ;
 ;==================================================================================================
-;   RCBUS Z80 ZRC CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR RCBUS Z80 ROMLESS ZRC
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE PLATFORM_NAME "ZRC", " [", CONFIG, "]"
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz80.asm"
+#include "cfg_RCZ80.asm"
 ;
 CPUOSC		.SET	14745600	; CPU OSC FREQ IN MHZ
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP

Source/HBIOS/Config/RCZ80_zrc_std.asm

@@ -1,32 +1,52 @@
 ;
 ;==================================================================================================
-;   RCBUS Z80 ZRC CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR RCBUS Z80 ZRC
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE PLATFORM_NAME "ZRC", " [", CONFIG, "]"
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rcz80.asm"
+#include "cfg_RCZ80.asm"
 ;
 CPUOSC		.SET	14745600	; CPU OSC FREQ IN MHZ
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP

Source/HBIOS/Config/RPH_std.asm

@@ -1,30 +1,50 @@
 ;
 ;==================================================================================================
-;   RHYOPHYRE STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR RHYOPHYRE
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_rph.asm"
+#include "cfg_RPH.asm"
 ;
 CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP

Source/HBIOS/Config/S100_std.asm

@@ -1,30 +1,50 @@
 ;
 ;==================================================================================================
-;   S100 STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR S100
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_s100.asm"
+#include "cfg_S100.asm"
 ;
 CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
 CRTACT		.SET	TRUE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP

Source/HBIOS/Config/SBC_max.asm

@@ -27,7 +27,7 @@
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_sbc.asm"
+#include "cfg_SBC.asm"
 ;
 BATCOND		.SET	TRUE		; ENABLE LOW BATTERY WARNING MESSAGE
 HBIOS_MUTEX	.SET	TRUE		; ENABLE REENTRANT CALLS TO HBIOS (ADDS OVERHEAD)

Source/HBIOS/Config/SBC_simh.asm

@@ -24,7 +24,7 @@
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_sbc.asm"
+#include "cfg_SBC.asm"
 ;
 INTMODE		.SET	1		; INTERRUPTS: 0=NONE, 1=MODE 1, 2=MODE 2
 ;
@@ -33,7 +33,15 @@ HTIMENABLE	.SET	TRUE		; ENABLE SIMH TIMER SUPPORT
 SIMRTCENABLE	.SET	TRUE		; ENABLE SIMH CLOCK DRIVER (SIMRTC.ASM)
 DSRTCENABLE	.SET	FALSE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
 ;
-UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
-UARTSBCFORCE	.SET	TRUE		; UART: FORCE DETECTION OF SBC UART (FOR SIMH)
+UARTENABLE	.SET	FALSE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+;
+SSERENABLE	.SET	TRUE		; SSER: ENABLE SIMPLE SERIAL DRIVER (SSER.ASM)
+SSERCFG		.SET	SER_9600_8N1	; SSER: SERIAL LINE CONFIG
+SSERSTATUS	.SET	$6D		; SSER: STATUS PORT
+SSERDATA	.SET	$68		; SSER: DATA PORT
+SSERIRDY	.SET	%00000001	; SSER: INPUT READY BIT MASK
+SSERIINV	.SET	FALSE		; SSER: INPUT READY BIT INVERTED
+SSERORDY	.SET	%00100000	; SSER: OUTPUT READY BIT MASK
+SSEROINV	.SET	FALSE		; SSER: OUTPUT READY BIT INVERTED
 ;
 HDSKENABLE	.SET	TRUE		; HDSK: ENABLE SIMH HDSK DISK DRIVER (HDSK.ASM)

Source/HBIOS/Config/SBC_std.asm

@@ -1,41 +1,56 @@
 ;
 ;==================================================================================================
-;   SBC STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR N8VEM SBC
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_sbc.asm"
+#include "cfg_SBC.asm"
 ;
 CPUOSC		.SET	8000000		; CPU OSC FREQ IN MHZ
 INTMODE		.SET	0		; INTERRUPTS: 0=NONE, 1=MODE 1, 2=MODE 2
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
 ;
 UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
-UARTSBC		.SET	TRUE		; UART: AUTO-DETECT SBC/ZETA ONBOARD UART
-UARTCAS		.SET	TRUE		; UART: AUTO-DETECT ECB CASSETTE UART
-UARTMFP		.SET	TRUE		; UART: AUTO-DETECT MF/PIC UART
-UART4		.SET	TRUE		; UART: AUTO-DETECT 4UART UART
-UARTRC		.SET	FALSE		; UART: AUTO-DETECT RC UART
 SIOENABLE	.SET	TRUE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
 ;
 TMSENABLE	.SET	FALSE		; TMS: ENABLE TMS9918 VIDEO/KBD DRIVER (TMS.ASM)

Source/HBIOS/Config/SCZ180_sc126_std.asm

@@ -1,32 +1,52 @@
 ;
 ;==================================================================================================
-;   SC126 STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR SC126
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE PLATFORM_NAME "Small Computer SC126", " [", CONFIG, "]"
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_scz180.asm"
+#include "cfg_SCZ180.asm"
 ;
 CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP

Source/HBIOS/Config/SCZ180_sc130_std.asm

@@ -1,32 +1,52 @@
 ;
 ;==================================================================================================
-;   SC130 STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR SC130
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE PLATFORM_NAME "Small Computer SC130", " [", CONFIG, "]"
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_scz180.asm"
+#include "cfg_SCZ180.asm"
 ;
 CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP

Source/HBIOS/Config/SCZ180_sc131.asm

@@ -1,55 +0,0 @@
-;
-;==================================================================================================
-;   SC131 STANDARD CONFIGURATION
-;==================================================================================================
-;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
-;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
-;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
-;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
-;
-#DEFINE PLATFORM_NAME "Small Computer SC131", " [", CONFIG, "]"
-;
-#DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
-;
-#include "cfg_scz180.asm"
-;
-CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
-;
-Z180_CLKDIV	.SET	1		; Z180: CHK DIV: 0=OSC/2, 1=OSC, 2=OSC*2
-Z180_MEMWAIT	.SET	0		; Z180: MEMORY WAIT STATES (0-3)
-Z180_IOWAIT	.SET	1		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
-;
-FPLED_ENABLE	.SET	FALSE		; FP: ENABLES FRONT PANEL LEDS
-FPSW_ENABLE	.SET	FALSE		; FP: ENABLES FRONT PANEL SWITCHES
-;
-LEDENABLE	.SET	TRUE		; ENABLE STATUS LED (SINGLE LED)
-;
-DSRTCENABLE	.SET	FALSE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
-INTRTCENABLE	.SET	TRUE		; ENABLE PERIODIC INTERRUPT CLOCK DRIVER (INTRTC.ASM)
-;
-UARTENABLE	.SET	FALSE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
-ASCIENABLE	.SET	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
-ACIAENABLE	.SET	FALSE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
-SIOENABLE	.SET	FALSE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
-;
-IDEENABLE	.SET	FALSE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
-PPIDEENABLE	.SET	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
-SDENABLE	.SET	TRUE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
-SDMODE		.SET	SDMODE_SC	; SD: DRIVER MODE: SDMODE_[JUHA|N8|CSIO|PPI|UART|DSD|MK4|SC|MT|USR]
-SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD & SC ONLY
-CHENABLE	.SET	FALSE		; CH: ENABLE CH375/376 USB SUPPORT

Source/HBIOS/Config/SCZ180_sc131_std.asm

@@ -0,0 +1,75 @@
+;
+;==================================================================================================
+;   ROMWBW DEFAULT BUILD SETTINGS FOR SC131
+;==================================================================================================
+;
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
+;
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
+;
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
+;
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
+;
+#DEFINE PLATFORM_NAME "Small Computer SC131", " [", CONFIG, "]"
+;
+#DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
+;
+#include "cfg_SCZ180.asm"
+;
+CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
+;
+Z180_CLKDIV	.SET	1		; Z180: CHK DIV: 0=OSC/2, 1=OSC, 2=OSC*2
+Z180_MEMWAIT	.SET	0		; Z180: MEMORY WAIT STATES (0-3)
+Z180_IOWAIT	.SET	1		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
+;
+FPLED_ENABLE	.SET	FALSE		; FP: ENABLES FRONT PANEL LEDS
+FPSW_ENABLE	.SET	FALSE		; FP: ENABLES FRONT PANEL SWITCHES
+;
+LEDENABLE	.SET	TRUE		; ENABLE STATUS LED (SINGLE LED)
+;
+DSRTCENABLE	.SET	FALSE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
+INTRTCENABLE	.SET	TRUE		; ENABLE PERIODIC INTERRUPT CLOCK DRIVER (INTRTC.ASM)
+;
+UARTENABLE	.SET	FALSE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+ASCIENABLE	.SET	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
+ACIAENABLE	.SET	FALSE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
+SIOENABLE	.SET	FALSE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
+;
+IDEENABLE	.SET	FALSE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
+PPIDEENABLE	.SET	FALSE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
+SDENABLE	.SET	TRUE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
+SDMODE		.SET	SDMODE_SC	; SD: DRIVER MODE: SDMODE_[JUHA|N8|CSIO|PPI|UART|DSD|MK4|SC|MT|USR]
+SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD & SC ONLY
+CHENABLE	.SET	FALSE		; CH: ENABLE CH375/376 USB SUPPORT

Source/HBIOS/Config/SCZ180_sc140_std.asm

@@ -1,32 +1,52 @@
 ;
 ;==================================================================================================
-;   SC140 STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR PLATFORM: SBC
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE PLATFORM_NAME "Small Computer SC140", " [", CONFIG, "]"
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_scz180.asm"
+#include "cfg_SCZ180.asm"
 ;
 CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
 ;

Source/HBIOS/Config/SCZ180_sc503_std.asm

@@ -1,32 +1,52 @@
 ;
 ;==================================================================================================
-;   SC503 STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR SC503
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE PLATFORM_NAME "Small Computer SC503", " [", CONFIG, "]"
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_scz180.asm"
+#include "cfg_SCZ180.asm"
 ;
 CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
 ;
@@ -40,6 +60,7 @@ FPSW_ENABLE	.SET	TRUE		; FP: ENABLES FRONT PANEL SWITCHES
 FPSW_IO		.SET	$A0		; FP: PORT ADDRESS FOR FP SWITCHES
 ;
 LEDENABLE	.SET	TRUE		; ENABLE STATUS LED (SINGLE LED)
+LEDMODE		.SET	LEDMODE_STD	; LEDMODE_[STD|SC|RTC|NABU]
 ;
 DSRTCENABLE	.SET	TRUE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
 INTRTCENABLE	.SET	TRUE		; ENABLE PERIODIC INTERRUPT CLOCK DRIVER (INTRTC.ASM)

Source/HBIOS/Config/SCZ180_sc700_std.asm

@@ -1,32 +1,52 @@
 ;
 ;==================================================================================================
-;   SC700 STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR SC700
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE PLATFORM_NAME "Small Computer SC700", " [", CONFIG, "]"
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_scz180.asm"
+#include "cfg_SCZ180.asm"
 ;
 CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
 CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
@@ -37,7 +57,6 @@ Z180_IOWAIT	.SET	1		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
 ;
 LEDENABLE	.SET	TRUE		; ENABLE STATUS LED (SINGLE LED)
 LEDMODE		.SET	LEDMODE_STD	; LEDMODE_[STD|SC|RTC|NABU]
-LEDPORT		.SET	$0E		; STATUS LED PORT ADDRESS
 ;
 FPLED_ENABLE	.SET	TRUE		; FP: ENABLES FRONT PANEL LEDS
 FPLED_IO	.SET	$00		; FP: PORT ADDRESS FOR FP LEDS

Source/HBIOS/Config/UNA_std.asm

@@ -1,27 +1,47 @@
 ;
 ;==================================================================================================
-;   UNA STANDARD CONFIGURATION
+;   ROMWBW DEFAULT BUILD SETTINGS FOR UNA
 ;==================================================================================================
 ;
-; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
-; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
-; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
-; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
-; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
-; YOUR FILE IN THE BUILD PROCESS.
+; THIS FILE DEFINES THE DEFAULT CONFIGURATION SETTINGS FOR THE PLATFORM
+; INDICATED ABOVE.  THESE SETTINGS DEFINE THE OFFICIAL BUILD FOR THIS
+; PLATFORM AS DISTRIBUTED IN ROMWBW RELEASES.
 ;
-; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
-; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
-; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
-; SETTINGS.
+; ROMWBW USES CASCADING CONFIGURATION FILES AS INDICATED BELOW:
 ;
-; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
-; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
-; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+; cfg_MASTER.asm			- MASTER: CONFIGURATION FILE DEFINES ALL POSSIBLE ROMWBW SETTINGS
+; |
+; +-> cfg_<platform>.asm		- PLATFORM: DEFAULT SETTINGS FOR SPECIFIC PLATFORM
+;     |
+;     +-> Config/<plt>_std.asm		- BUILD: SETTINGS FOR EACH OFFICIAL DIST BUILD
+;         |
+;         +-> Config/<plt>_<cust>.asm	- USER: CUSTOM USER BUILD SETTINGS
 ;
-; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
-; DIRECTORIES ABOVE THIS ONE).
+; THE TOP (MASTER CONFIGURATION) FILE DEFINES ALL POSSIBLE ROMWBW
+; CONFIGURATION SETTINGS. EACH FILE BELOW THE MASTER CONFIGURATION FILE
+; INHERITS THE CUMULATIVE SETTINGS OF THE FILES ABOVE IT AND MAY
+; OVERRIDE THESE SETTINGS AS DESIRED.
+;
+; OTHER THAN THE TOP MASTER FILE, EACH FILE MUST "#INCLUDE" ITS PARENT
+; FILE (SEE #INCLUDE STATEMENT BELOW).  THE TOP TWO FILES SHOULD NOT BE
+; MODIFIED.
+;
+; TO CUSTOMIZE YOUR BUILD SETTINGS YOU SHOULD MODIFY THIS FILE, THE
+; DEFAULT BUILD SETTINGS (Config/<platform>_std.asm) OR PREFERABLY
+; CREATE AN OPTIONAL CUSTOM USER SETTINGS FILE THAT INCLUDES THE DEFAULT
+; BUILD SETTINGS FILE (SEE EXAMPLE Config/SBC_user.asm).
+;
+; BY CREATING A CUSTOM USER SETTINGS FILE, YOU ARE LESS LIKELY TO BE
+; IMPACTED BY FUTURE CHANGES BECAUSE YOU WILL BE INHERITING MOST
+; OF YOUR SETTINGS WHICH WILL BE UPDATED BY AUTHORS AS ROMWBW EVOLVES.
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE
+; SOURCE DIRECTORY (TWO DIRECTORIES ABOVE THIS ONE).
+;
+; *** WARNING: ASIDE FROM THE MASTER CONFIGURATION FILE, YOU MUST USE
+; ".SET" TO OVERRIDE SETTINGS.  THE ASSEMBLER WILL ERROR IF YOU ATTEMPT
+; TO USE ".EQU" BECAUSE IT WON'T LET YOU REDEFINE A SETTING WITH ".EQU".
 ;
 #DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
 ;
-#include "cfg_una.asm"
+#include "cfg_UNA.asm"